| # Kconfig.hdc1008 - HDC1008 temperature and humidity sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig HDC1008 |
| bool |
| prompt "HDC1008 Temperature and Humidity Sensor" |
| depends on SENSOR && I2C && GPIO |
| default n |
| help |
| Enable driver for HDC1008 temperature and humidity sensors. |
| |
| config HDC1008_SYS_LOG_LEVEL |
| int "HDC1008 Log level" |
| depends on SYS_LOG && HDC1008 |
| default 0 |
| range 0 4 |
| help |
| Sets log level for HDC1008 driver. |
| Levels are: |
| |
| - 0 OFF: do not write |
| |
| - 1 ERROR: only write SYS_LOG_ERR |
| |
| - 2 WARNING: write SYS_LOG_WRN in addition to previous level |
| |
| - 3 INFO: write SYS_LOG_INF in addition to previous levels |
| |
| - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels |
| |
| config HDC1008_NAME |
| string |
| prompt "Driver name" |
| default "HDC1008" |
| depends on HDC1008 |
| help |
| Device name with which the HDC1008 sensor is identified. |
| |
| config HDC1008_INIT_PRIORITY |
| int |
| prompt "Init priority" |
| depends on HDC1008 |
| default 70 |
| help |
| Device driver initialization priority. |
| |
| choice |
| prompt "I2C address" |
| depends on HDC1008 |
| default HDC1008_I2C_ADDR_0 |
| help |
| I2C address of the HDC1008 sensor. |
| |
| config HDC1008_I2C_ADDR_0 |
| bool |
| prompt "0x40" |
| help |
| A0 connected GND and A1 connected to GND. |
| |
| config HDC1008_I2C_ADDR_1 |
| bool |
| prompt "0x41" |
| help |
| A0 connected VDD and A1 connected to GND. |
| |
| config HDC1008_I2C_ADDR_2 |
| bool |
| prompt "0x42" |
| help |
| A0 connected GND and A1 connected to VDD. |
| |
| config HDC1008_I2C_ADDR_3 |
| bool |
| prompt "0x43" |
| help |
| A0 connected VDD and A1 connected to VDD. |
| |
| endchoice |
| |
| config HDC1008_I2C_MASTER_DEV_NAME |
| string |
| prompt "I2C master where HDC1008 is connected" |
| depends on HDC1008 |
| default "I2C_0" |
| help |
| Specify the device name of the I2C master device to which the |
| HDC1008 chip is connected. |
| |
| config HDC1008_GPIO_DEV_NAME |
| string |
| prompt "GPIO device" |
| default "GPIO_0" |
| depends on HDC1008 |
| help |
| The device name of the GPIO device to which the HDC1008 data-ready |
| pin is connected. |
| |
| config HDC1008_GPIO_PIN_NUM |
| int |
| prompt "Interrupt GPIO pin number" |
| default 0 |
| depends on HDC1008 |
| help |
| The number of the GPIO on which the data-ready signal from the HDC1008 |
| chip will be received. |
