| # Kconfig.mcp9808 - MCP9808 temperature sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig MCP9808 |
| bool "MCP9808 temperature sensor" |
| depends on SENSOR && I2C |
| default n |
| help |
| Enable driver for MCP9808 temperature sensor. |
| |
| config MCP9808_SYS_LOG_LEVEL |
| int "MCP9808 Log level" |
| depends on SYS_LOG && MCP9808 |
| default 0 |
| range 0 4 |
| help |
| Sets log level for MCP9808 driver. |
| Levels are: |
| |
| - 0 OFF: do not write |
| |
| - 1 ERROR: only write SYS_LOG_ERR |
| |
| - 2 WARNING: write SYS_LOG_WRN in addition to previous level |
| |
| - 3 INFO: write SYS_LOG_INF in addition to previous levels |
| |
| - 4 DEBUG: write SYS_LOG_DBG in addition to previous levels |
| |
| config MCP9808_DEV_NAME |
| string "MCP9808 device name" |
| depends on MCP9808 |
| default "MCP9808" |
| |
| config MCP9808_INIT_PRIORITY |
| int |
| depends on MCP9808 |
| default 70 |
| prompt "Init priority" |
| help |
| Device driver initialization priority. |
| |
| config MCP9808_I2C_ADDR |
| hex "MCP9808 I2C slave address" |
| depends on MCP9808 |
| default 0x18 |
| help |
| Specify the I2C slave address for the MCP9808. |
| |
| config MCP9808_I2C_DEV_NAME |
| string "I2C master where MCP9808 is connected" |
| depends on MCP9808 |
| default "I2C_0" |
| help |
| Specify the device name of the I2C master device to which MCP9808 is |
| connected. |
| |
| choice |
| prompt "MCP9808 trigger mode" |
| depends on MCP9808 |
| default MCP9808_TRIGGER_NONE |
| |
| config MCP9808_TRIGGER_NONE |
| bool "No trigger" |
| |
| config MCP9808_TRIGGER_GLOBAL_FIBER |
| depends on GPIO && SYSTEM_WORKQUEUE |
| select MCP9808_TRIGGER |
| bool "Use global fiber" |
| |
| config MCP9808_TRIGGER_OWN_FIBER |
| depends on GPIO |
| select MCP9808_TRIGGER |
| bool "Use own fiber" |
| |
| endchoice |
| |
| config MCP9808_TRIGGER |
| bool |
| depends on MCP9808 |
| |
| config MCP9808_GPIO_CONTROLLER |
| string "GPIO controller for MCP9808 interrupt" |
| depends on MCP9808 && MCP9808_TRIGGER |
| default "GPIO_0" |
| help |
| The GPIO controller the MCP9808 interrupt is connected to. |
| |
| config MCP9808_GPIO_PIN |
| int "GPIO pin for MCP9808 interrupt" |
| depends on MCP9808 && MCP9808_TRIGGER |
| default 3 |
| help |
| The GPIO pin the MCP9808 interrupt is connected to. |
| |
| config MCP9808_FIBER_STACK_SIZE |
| int "Sensor delayed work fiber stack size" |
| depends on MCP9808 && MCP9808_TRIGGER_OWN_FIBER |
| default 1024 |
| |
| config MCP9808_FIBER_PRIORITY |
| int "MCP9808 fiber priority" |
| depends on MCP9808 && MCP9808_TRIGGER_OWN_FIBER |
| default 10 |
