drivers/sensor/sensor_bmi160_trigger.c

/* Bosch BMI160 inertial measurement unit driver, trigger implementation
 *
 * Copyright (c) 2016 Intel Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

#include <nanokernel.h>
#include <sensor.h>

#ifdef CONFIG_BMI160_TRIGGER_SOURCE_GPIO
#include <gpio.h>
#else
#include <ipm.h>
#include <ipm/ipm_quark_se.h>
#endif

#include "sensor_bmi160.h"

static void bmi160_handle_anymotion(struct device *dev)
{
	struct bmi160_device_data *bmi160 = dev->driver_data;
	struct sensor_trigger anym_trigger = {
		.type = SENSOR_TRIG_DELTA,
		.chan = SENSOR_CHAN_ACCEL_ANY,
	};

	if (bmi160->handler_anymotion) {
		bmi160->handler_anymotion(dev, &anym_trigger);
	}
}

static void bmi160_handle_drdy(struct device *dev, uint8_t status)
{
	struct bmi160_device_data *bmi160 = dev->driver_data;
	struct sensor_trigger drdy_trigger = {
		.type = SENSOR_TRIG_DATA_READY,
	};

#if !defined(CONFIG_BMI160_ACCEL_PMU_SUSPEND)
	if (bmi160->handler_drdy_acc && (status & BMI160_STATUS_ACC_DRDY)) {
		drdy_trigger.chan = SENSOR_CHAN_ACCEL_ANY;
		bmi160->handler_drdy_acc(dev, &drdy_trigger);
	}
#endif

#if !defined(CONFIG_BMI160_GYRO_PMU_SUSPEND)
	if (bmi160->handler_drdy_gyr && (status & BMI160_STATUS_GYR_DRDY)) {
		drdy_trigger.chan = SENSOR_CHAN_GYRO_ANY;
		bmi160->handler_drdy_gyr(dev, &drdy_trigger);
	}
#endif
}

static void bmi160_handle_interrupts(void *arg)
{
	struct device *dev = (struct device *)arg;

	union {
		uint8_t raw[6];
		struct {
			uint8_t dummy; /* spi related dummy byte */
			uint8_t status;
			uint8_t int_status[4];
		};
	} buf;

	if (bmi160_read(dev, BMI160_REG_STATUS, buf.raw, sizeof(buf)) < 0) {
		return;
	}

	if ((buf.int_status[0] & BMI160_INT_STATUS0_ANYM) &&
	    (buf.int_status[2] & (BMI160_INT_STATUS2_ANYM_FIRST_X |
				  BMI160_INT_STATUS2_ANYM_FIRST_Y |
				  BMI160_INT_STATUS2_ANYM_FIRST_Z))) {
		bmi160_handle_anymotion(dev);
	}

	if (buf.int_status[1] & BMI160_INT_STATUS1_DRDY) {
		bmi160_handle_drdy(dev, buf.status);
	}

}

#ifdef CONFIG_BMI160_TRIGGER_OWN_FIBER
static char __stack bmi160_fiber_stack[CONFIG_BMI160_FIBER_STACK_SIZE];

static void bmi160_fiber_main(int arg1, int unused)
{
	struct device *dev = (struct device *)arg1;
	struct bmi160_device_data *bmi160 = dev->driver_data;

	while (1) {
		nano_fiber_sem_take(&bmi160->sem, TICKS_UNLIMITED);
		bmi160_handle_interrupts(dev);
	}
}
#endif

#ifdef CONFIG_BMI160_TRIGGER_GLOBAL_FIBER
static void bmi160_work_handler(struct nano_work *work)
{
	struct bmi160_device_data *bmi160 =
		CONTAINER_OF(work, struct bmi160_device_data, work);

	bmi160_handle_interrupts(bmi160->dev);
}
#endif

extern struct bmi160_device_data bmi160_data;

#ifdef CONFIG_BMI160_TRIGGER_SOURCE_GPIO
static void bmi160_gpio_callback(struct device *port,
				 struct gpio_callback *cb, uint32_t pin)
{
	struct bmi160_device_data *bmi160 =
		CONTAINER_OF(cb, struct bmi160_device_data, gpio_cb);

#if defined(CONFIG_BMI160_TRIGGER_OWN_FIBER)
	nano_sem_give(&bmi160->sem);
#elif defined(CONFIG_BMI160_TRIGGER_GLOBAL_FIBER)
	nano_work_submit(&bmi160->work);
#endif
}
#else
QUARK_SE_IPM_DEFINE(bmi160_ipm, 0, QUARK_SE_IPM_INBOUND);

static void bmi160_ipm_callback(void *context, uint32_t id, volatile void *data)
{
	struct bmi160_device_data *bmi160 = context;

#if defined(CONFIG_BMI160_TRIGGER_OWN_FIBER)
	nano_sem_give(&bmi160->sem);
#elif defined(CONFIG_BMI160_TRIGGER_GLOBAL_FIBER)
	nano_work_submit(&bmi160->work);
#endif
}
#endif

static int bmi160_trigger_drdy_set(struct device *dev,
				   enum sensor_channel chan,
				   sensor_trigger_handler_t handler)
{
	struct bmi160_device_data *bmi160 = dev->driver_data;
	uint8_t drdy_en = 0;

#if !defined(CONFIG_BMI160_ACCEL_PMU_SUSPEND)
	if (chan == SENSOR_CHAN_ACCEL_ANY) {
		bmi160->handler_drdy_acc = handler;
	}

	if (bmi160->handler_drdy_acc) {
		drdy_en = BMI160_INT_DRDY_EN;
	}
#endif

#if !defined(CONFIG_BMI160_GYRO_PMU_SUSPEND)
	if (chan == SENSOR_CHAN_GYRO_ANY) {
		bmi160->handler_drdy_gyr = handler;
	}

	if (bmi160->handler_drdy_gyr) {
		drdy_en = BMI160_INT_DRDY_EN;
	}
#endif

	if (bmi160_reg_update(dev, BMI160_REG_INT_EN1,
			      BMI160_INT_DRDY_EN, drdy_en) < 0) {
		return -EIO;
	}

	return 0;
}

#if !defined(CONFIG_BMI160_ACCEL_PMU_SUSPEND)
static int bmi160_trigger_anym_set(struct device *dev,
				   sensor_trigger_handler_t handler)
{
	struct bmi160_device_data *bmi160 = dev->driver_data;
	uint8_t anym_en = 0;

	bmi160->handler_anymotion = handler;

	if (handler) {
		anym_en = BMI160_INT_ANYM_X_EN |
			  BMI160_INT_ANYM_Y_EN |
			  BMI160_INT_ANYM_Z_EN;
	}

	if (bmi160_reg_update(dev, BMI160_REG_INT_EN0,
			      BMI160_INT_ANYM_MASK, anym_en) < 0) {
		return -EIO;
	}

	return 0;
}

static int bmi160_trigger_set_acc(struct device *dev,
				  const struct sensor_trigger *trig,
				  sensor_trigger_handler_t handler)
{
	if (trig->type == SENSOR_TRIG_DATA_READY) {
		return bmi160_trigger_drdy_set(dev, trig->chan, handler);
	} else if (trig->type == SENSOR_TRIG_DELTA) {
		return bmi160_trigger_anym_set(dev, handler);
	}

	return -ENOTSUP;
}

int bmi160_acc_slope_config(struct device *dev, enum sensor_attribute attr,
			    const struct sensor_value *val)
{
	uint8_t acc_range_g, reg_val;
	uint32_t slope_th_ums2;

	if (attr == SENSOR_ATTR_SLOPE_TH) {
		if (val->type != SENSOR_VALUE_TYPE_INT_PLUS_MICRO) {
			return -EINVAL;
		}

		if (bmi160_byte_read(dev, BMI160_REG_ACC_RANGE, &reg_val) < 0) {
			return -EIO;
		}

		acc_range_g = bmi160_acc_reg_val_to_range(reg_val);

		slope_th_ums2 = val->val1 * 1000000 + val->val2;

		/* make sure the provided threshold does not exceed range / 2 */
		if (slope_th_ums2 > (acc_range_g / 2 * SENSOR_G)) {
			return -EINVAL;
		}

		reg_val = 512 * (slope_th_ums2 - 1) / (acc_range_g * SENSOR_G);

		if (bmi160_byte_write(dev, BMI160_REG_INT_MOTION1,
				      reg_val) < 0) {
			return -EIO;
		}
	} else { /* SENSOR_ATTR_SLOPE_DUR */
		if (val->type != SENSOR_VALUE_TYPE_INT) {
			return -EINVAL;
		}

		/* slope duration is measured in number of samples */
		if (val->val1 < 1 || val->val1 > 4) {
			return -ENOTSUP;
		}

		if (bmi160_reg_field_update(dev, BMI160_REG_INT_MOTION0,
					    BMI160_ANYM_DUR_POS,
					    BMI160_ANYM_DUR_MASK,
					    val->val1) < 0) {
			return -EIO;
		}
	}

	return 0;
}
#endif

#if !defined(CONFIG_BMI160_GYRO_PMU_SUSPEND)
static int bmi160_trigger_set_gyr(struct device *dev,
				  const struct sensor_trigger *trig,
				  sensor_trigger_handler_t handler)
{
	if (trig->type == SENSOR_TRIG_DATA_READY) {
		return bmi160_trigger_drdy_set(dev, trig->chan, handler);
	}

	return -ENOTSUP;
}
#endif

int bmi160_trigger_set(struct device *dev,
		       const struct sensor_trigger *trig,
		       sensor_trigger_handler_t handler)
{
#if !defined(CONFIG_BMI160_ACCEL_PMU_SUSPEND)
	if (trig->chan == SENSOR_CHAN_ACCEL_ANY) {
		return bmi160_trigger_set_acc(dev, trig, handler);
	}
#endif
#if !defined(CONFIG_BMI160_GYRO_PMU_SUSPEND)
	if (trig->chan == SENSOR_CHAN_GYRO_ANY) {
		return bmi160_trigger_set_gyr(dev, trig, handler);
	}
#endif
	return -ENOTSUP;
}

int bmi160_trigger_mode_init(struct device *dev)
{
	struct bmi160_device_data *bmi160 = dev->driver_data;

#ifdef CONFIG_BMI160_TRIGGER_SOURCE_GPIO
	struct bmi160_device_config *cfg = dev->config->config_info;

	bmi160->gpio = device_get_binding((char *)cfg->gpio_port);
	if (!bmi160->gpio) {
		SYS_LOG_DBG("Gpio controller %s not found.", cfg->gpio_port);
		return -EINVAL;
	}
#else /* CONFIG_BMI160_TRIGGER_SOURCE_IPM */
	bmi160->ipm = device_get_binding("bmi160_ipm");
	if (!bmi160->ipm) {
		SYS_LOG_DBG("Ipm device bmi160_ipm not found.");
		return -EINVAL;
	}
#endif

#if defined(CONFIG_BMI160_TRIGGER_OWN_FIBER)
	nano_sem_init(&bmi160->sem);

	fiber_start(bmi160_fiber_stack, CONFIG_BMI160_FIBER_STACK_SIZE,
		    bmi160_fiber_main, (int)dev, 0,
		    CONFIG_BMI160_FIBER_PRIORITY, 0);
#elif defined(CONFIG_BMI160_TRIGGER_GLOBAL_FIBER)
	bmi160->work.handler = bmi160_work_handler;
	bmi160->dev = dev;
#endif

	/* map all interrupts to INT1 pin */
	if (bmi160_word_write(dev, BMI160_REG_INT_MAP0, 0xf0ff) < 0) {
		SYS_LOG_DBG("Failed to map interrupts.");
		return -EIO;
	}

#if defined(CONFIG_BMI160_TRIGGER_SOURCE_GPIO)
	gpio_pin_configure(bmi160->gpio, cfg->int_pin,
			   GPIO_DIR_IN | GPIO_INT | GPIO_INT_EDGE |
			   GPIO_INT_ACTIVE_LOW | GPIO_INT_DEBOUNCE);

	gpio_init_callback(&bmi160->gpio_cb,
			   bmi160_gpio_callback,
			   BIT(cfg->int_pin));

	gpio_add_callback(bmi160->gpio, &bmi160->gpio_cb);
	gpio_pin_enable_callback(bmi160->gpio, cfg->int_pin);
#elif defined(CONFIG_BMI160_TRIGGER_SOURCE_IPM)
	ipm_register_callback(bmi160->ipm, bmi160_ipm_callback, bmi160);
	ipm_set_enabled(bmi160->ipm, 1);
#endif

	return bmi160_byte_write(dev, BMI160_REG_INT_OUT_CTRL,
				 BMI160_INT1_OUT_EN | BMI160_INT1_EDGE_CTRL);
}