| /* |
| * Copyright (c) 2020, NXP |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #include <mem.h> |
| #include <arm/armv8-m.dtsi> |
| #include <zephyr/dt-bindings/clock/mcux_lpc_syscon_clock.h> |
| #include <zephyr/dt-bindings/gpio/gpio.h> |
| #include <zephyr/dt-bindings/i2c/i2c.h> |
| |
| / { |
| chosen { |
| zephyr,entropy = &trng; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-m33f"; |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| mpu: mpu@e000ed90 { |
| compatible = "arm,armv8m-mpu"; |
| reg = <0xe000ed90 0x40>; |
| arm,num-mpu-regions = <8>; |
| }; |
| }; |
| }; |
| }; |
| |
| &sram { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| sram0: memory@20180000 { |
| compatible = "mmio-sram"; |
| reg = <0x20180000 DT_SIZE_K(3072)>; |
| }; |
| |
| sram1: memory@40140000 { |
| compatible = "zephyr,memory-region", "mmio-sram"; |
| reg = <0x40140000 DT_SIZE_K(16)>; |
| zephyr,memory-region = "SRAM1"; |
| }; |
| }; |
| |
| &systick { |
| /* |
| * RT600 relies by default on the OS Timer for system clock |
| * implementation, so the SysTick node is not to be enabled. |
| */ |
| status = "disabled"; |
| }; |
| |
| &peripheral { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| /* |
| * Note that the offsets here are relative to the base address |
| * defined in either nxp_rt6xx_ns.dtsi or nxp_rt6xx.dtsi. The base |
| * addresses differ between non-secure (0x40000000) and secure |
| * modes (0x50000000). |
| */ |
| |
| clkctl0: clkctl@1000 { |
| compatible = "nxp,lpc-syscon"; |
| reg = <0x1000 0x1000>; |
| #clock-cells = <1>; |
| }; |
| |
| iocon: iocon@4000 { |
| compatible = "nxp,lpc-iocon"; |
| reg = <0x4000 0x1000>; |
| pinctrl: pinctrl { |
| compatible = "nxp,rt-iocon-pinctrl"; |
| }; |
| }; |
| |
| clkctl1: clkctl@21000 { |
| compatible = "nxp,lpc-syscon"; |
| reg = <0x21000 0x1000>; |
| #clock-cells = <1>; |
| }; |
| |
| uuid: uuid@2f50 { |
| compatible = "nxp,lpc-uid"; |
| reg = <0x2f50 0x10>; |
| }; |
| |
| gpio0: gpio@0 { |
| compatible = "nxp,lpc-gpio"; |
| reg = <0x100000 0x1000>; |
| interrupts = <4 2>,<5 2>,<6 2>,<7 2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| port = <0>; |
| }; |
| |
| gpio1: gpio@1 { |
| compatible = "nxp,lpc-gpio"; |
| reg = <0x100000 0x1000>; |
| interrupts = <35 2>,<36 2>,<37 2>,<38 2>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| port = <1>; |
| }; |
| |
| gpio2: gpio@2 { |
| compatible = "nxp,lpc-gpio"; |
| reg = <0x100000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| port = <2>; |
| }; |
| |
| gpio3: gpio@3 { |
| compatible = "nxp,lpc-gpio"; |
| reg = <0x100000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| port = <3>; |
| }; |
| |
| gpio4: gpio@4 { |
| compatible = "nxp,lpc-gpio"; |
| reg = <0x100000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| port = <4>; |
| }; |
| |
| gpio7: gpio@7 { |
| compatible = "nxp,lpc-gpio"; |
| reg = <0x100000 0x1000>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| port = <7>; |
| }; |
| |
| flexcomm0: flexcomm@106000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x106000 0x1000>; |
| interrupts = <14 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM0_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm1: flexcomm@107000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x107000 0x1000>; |
| interrupts = <15 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM1_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm2: flexcomm@108000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x108000 0x1000>; |
| interrupts = <16 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM2_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm3: flexcomm@109000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x109000 0x1000>; |
| interrupts = <17 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM3_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm4: flexcomm@122000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x122000 0x1000>; |
| interrupts = <18 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM4_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm5: flexcomm@123000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x123000 0x1000>; |
| interrupts = <19 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM5_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm6: flexcomm@124000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x124000 0x1000>; |
| interrupts = <43 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM6_CLK>; |
| status = "disabled"; |
| }; |
| |
| flexcomm7: flexcomm@125000 { |
| compatible = "nxp,lpc-flexcomm"; |
| reg = <0x125000 0x1000>; |
| interrupts = <44 0>; |
| clocks = <&clkctl1 MCUX_FLEXCOMM7_CLK>; |
| status = "disabled"; |
| }; |
| |
| pmic_i2c: i2c@127000 { |
| compatible = "nxp,lpc-i2c"; |
| reg = <0x127000 0x1000>; |
| interrupts = <21 0>; |
| clocks = <&clkctl1 MCUX_PMIC_I2C_CLK>; |
| status = "disabled"; |
| }; |
| |
| usbhs: usbhs@144000 { |
| compatible = "nxp,mcux-usbd"; |
| reg = <0x144000 0x1000>; |
| interrupts = <50 1>; |
| num-bidir-endpoints = <6>; |
| usb-controller-index = "LpcIp3511Hs0"; |
| status = "disabled"; |
| }; |
| |
| hs_lspi: spi@126000 { |
| compatible = "nxp,lpc-spi"; |
| /* Enabling cs-gpios below will allow using GPIO CS, |
| rather than Flexcomm SS */ |
| /* cs-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>, |
| <&gpio1 15 GPIO_ACTIVE_LOW>, |
| <&gpio1 16 GPIO_ACTIVE_LOW>, |
| <&gpio1 17 GPIO_ACTIVE_LOW>; */ |
| reg = <0x126000 0x1000>; |
| interrupts = <20 0>; |
| clocks = <&clkctl1 MCUX_HS_SPI_CLK>; |
| status = "disabled"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| dma0: dma-controller@104000 { |
| compatible = "nxp,lpc-dma"; |
| reg = <0x104000 0x1000>; |
| interrupts = <1 0>; |
| status = "disabled"; |
| #dma-cells = <1>; |
| }; |
| |
| dma1: dma-controller@105000 { |
| compatible = "nxp,lpc-dma"; |
| reg = <0x105000 0x1000>; |
| interrupts = <54 0>; |
| status = "disabled"; |
| #dma-cells = <1>; |
| }; |
| |
| os_timer: timers@113000 { |
| compatible = "nxp,os-timer"; |
| reg = <0x113000 0x1000>; |
| interrupts = <41 0>; |
| status = "disabled"; |
| }; |
| |
| rtc: rtc@30000 { |
| compatible = "nxp,lpc-rtc"; |
| reg = <0x30000 0x1000>; |
| interrupts = <32 0>; |
| status = "disabled"; |
| }; |
| |
| trng: random@138000 { |
| compatible = "nxp,kinetis-trng"; |
| reg = <0x138000 0x1000>; |
| status = "okay"; |
| interrupts = <31 0>; |
| }; |
| |
| sc_timer: pwm@146000 { |
| compatible = "nxp,sctimer-pwm"; |
| reg = <0x146000 0x1000>; |
| interrupts = <12 0>; |
| status = "disabled"; |
| prescaler = <8>; |
| #pwm-cells = <3>; |
| }; |
| |
| wwdt0: watchdog@e000 { |
| compatible = "nxp,lpc-wwdt"; |
| reg = <0xe000 0x1000>; |
| interrupts = <0 0>; |
| status = "disabled"; |
| clk-divider = <1>; |
| }; |
| |
| wwdt1: watchdog@2e000 { |
| compatible = "nxp,lpc-wwdt"; |
| reg = <0x2e000 0x1000>; |
| interrupts = <52 0>; |
| status = "disabled"; |
| clk-divider = <1>; |
| }; |
| |
| usdhc0: usdhc@136000 { |
| compatible = "nxp,imx-usdhc"; |
| reg = <0x136000 0x1000>; |
| status = "disabled"; |
| interrupts = <45 0>; |
| clocks = <&clkctl1 MCUX_USDHC1_CLK>; |
| max-current-330 = <1020>; |
| max-current-180 = <1020>; |
| max-bus-freq = <208000000>; |
| min-bus-freq = <400000>; |
| }; |
| |
| usdhc1: usdhc@137000 { |
| compatible = "nxp,imx-usdhc"; |
| reg = <0x137000 0x1000>; |
| status = "disabled"; |
| interrupts = <46 0>; |
| clocks = <&clkctl1 MCUX_USDHC2_CLK>; |
| max-current-330 = <1020>; |
| max-current-180 = <1020>; |
| max-bus-freq = <208000000>; |
| min-bus-freq = <400000>; |
| }; |
| |
| lpadc0: lpadc@13A0000 { |
| compatible = "nxp,lpc-lpadc"; |
| reg = <0x13A000 0x304>; |
| interrupts = <22 0>; |
| status = "disabled"; |
| clk-divider = <1>; |
| clk-source = <0>; |
| voltage-ref= <2>; |
| calibration-average = <128>; |
| power-level = <1>; |
| offset-value-a = <10>; |
| offset-value-b = <10>; |
| #io-channel-cells = <1>; |
| }; |
| |
| ctimer0: ctimer@28000 { |
| compatible = "nxp,lpc-ctimer"; |
| reg = <0x28000 0x1000>; |
| interrupts = <10 0>; |
| status = "disabled"; |
| clk-source = <1>; |
| clocks = <&clkctl1 MCUX_CTIMER0_CLK>; |
| mode = <0>; |
| input = <0>; |
| prescale = <0>; |
| }; |
| |
| ctimer1: ctimer@29000 { |
| compatible = "nxp,lpc-ctimer"; |
| reg = <0x29000 0x1000>; |
| interrupts = <11 0>; |
| status = "disabled"; |
| clk-source = <1>; |
| clocks = <&clkctl1 MCUX_CTIMER1_CLK>; |
| mode = <0>; |
| input = <0>; |
| prescale = <0>; |
| }; |
| |
| ctimer2: ctimer@2a000 { |
| compatible = "nxp,lpc-ctimer"; |
| reg = <0x2a000 0x1000>; |
| interrupts = <39 0>; |
| status = "disabled"; |
| clk-source = <1>; |
| clocks = <&clkctl1 MCUX_CTIMER2_CLK>; |
| mode = <0>; |
| input = <0>; |
| prescale = <0>; |
| }; |
| |
| ctimer3: ctimer@2b000 { |
| compatible = "nxp,lpc-ctimer"; |
| reg = <0x2b000 0x1000>; |
| interrupts = <13 0>; |
| status = "disabled"; |
| clk-source = <1>; |
| clocks = <&clkctl1 MCUX_CTIMER3_CLK>; |
| mode = <0>; |
| input = <0>; |
| prescale = <0>; |
| }; |
| |
| ctimer4: ctimer@2c000 { |
| compatible = "nxp,lpc-ctimer"; |
| reg = <0x2c000 0x1000>; |
| interrupts = <40 0>; |
| status = "disabled"; |
| clk-source = <1>; |
| clocks = <&clkctl1 MCUX_CTIMER4_CLK>; |
| mode = <0>; |
| input = <0>; |
| prescale = <0>; |
| }; |
| |
| i3c0: i3c@36000 { |
| compatible = "nxp,mcux-i3c"; |
| reg = <0x36000 0x1000>; |
| interrupts = <49 0>; |
| clocks = <&clkctl1 MCUX_I3C_CLK>; |
| clk-divider = <2>; |
| clk-divider-slow = <1>; |
| clk-divider-tc = <1>; |
| status = "disabled"; |
| #address-cells = <3>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| &flexspi { |
| compatible = "nxp,imx-flexspi"; |
| interrupts = <42 0>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| &nvic { |
| arm,num-irq-priority-bits = <3>; |
| }; |
