| /* |
| * Copyright (c) 2020 Intel Corporation |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #define DT_DRV_COMPAT zephyr_gsm_ppp |
| |
| #include <zephyr/logging/log.h> |
| LOG_MODULE_REGISTER(modem_gsm, CONFIG_MODEM_LOG_LEVEL); |
| |
| #include <stdlib.h> |
| #include <zephyr/kernel.h> |
| #include <zephyr/device.h> |
| #include <zephyr/sys/ring_buffer.h> |
| #include <zephyr/sys/util.h> |
| #include <zephyr/net/ppp.h> |
| #include <zephyr/drivers/modem/gsm_ppp.h> |
| #include <zephyr/drivers/uart.h> |
| #include <zephyr/drivers/console/uart_mux.h> |
| |
| #include "modem_context.h" |
| #include "modem_iface_uart.h" |
| #include "modem_cmd_handler.h" |
| #include "../console/gsm_mux.h" |
| |
| #include <stdio.h> |
| |
| #define GSM_UART_NODE DT_INST_BUS(0) |
| #define GSM_CMD_READ_BUF 128 |
| #define GSM_CMD_AT_TIMEOUT K_SECONDS(2) |
| #define GSM_CMD_SETUP_TIMEOUT K_SECONDS(6) |
| /* GSM_CMD_LOCK_TIMEOUT should be longer than GSM_CMD_AT_TIMEOUT & GSM_CMD_SETUP_TIMEOUT, |
| * otherwise the gsm_ppp_stop might fail to lock tx. |
| */ |
| #define GSM_CMD_LOCK_TIMEOUT K_SECONDS(10) |
| #define GSM_RECV_MAX_BUF 30 |
| #define GSM_RECV_BUF_SIZE 128 |
| #define GSM_ATTACH_RETRY_DELAY_MSEC 1000 |
| #define GSM_REGISTER_DELAY_MSEC 1000 |
| #define GSM_RETRY_DELAY K_SECONDS(1) |
| |
| #define GSM_RSSI_RETRY_DELAY_MSEC 2000 |
| #define GSM_RSSI_RETRIES 10 |
| #define GSM_RSSI_INVALID -1000 |
| |
| #if defined(CONFIG_MODEM_GSM_ENABLE_CESQ_RSSI) |
| #define GSM_RSSI_MAXVAL 0 |
| #else |
| #define GSM_RSSI_MAXVAL -51 |
| #endif |
| |
| /* Modem network registration state */ |
| enum network_state { |
| GSM_NET_INIT = -1, |
| GSM_NET_NOT_REGISTERED, |
| GSM_NET_HOME_NETWORK, |
| GSM_NET_SEARCHING, |
| GSM_NET_REGISTRATION_DENIED, |
| GSM_NET_UNKNOWN, |
| GSM_NET_ROAMING, |
| }; |
| |
| static struct gsm_modem { |
| struct k_mutex lock; |
| const struct device *dev; |
| struct modem_context context; |
| |
| struct modem_cmd_handler_data cmd_handler_data; |
| uint8_t cmd_match_buf[GSM_CMD_READ_BUF]; |
| struct k_sem sem_response; |
| struct k_sem sem_if_down; |
| |
| struct modem_iface_uart_data gsm_data; |
| struct k_work_delayable gsm_configure_work; |
| char gsm_rx_rb_buf[PPP_MRU * 3]; |
| |
| uint8_t *ppp_recv_buf; |
| size_t ppp_recv_buf_len; |
| |
| enum gsm_ppp_state { |
| GSM_PPP_START, |
| GSM_PPP_WAIT_AT, |
| GSM_PPP_AT_RDY, |
| GSM_PPP_STATE_INIT, |
| GSM_PPP_STATE_CONTROL_CHANNEL = GSM_PPP_STATE_INIT, |
| GSM_PPP_STATE_PPP_CHANNEL, |
| GSM_PPP_STATE_AT_CHANNEL, |
| GSM_PPP_STATE_DONE, |
| GSM_PPP_SETUP = GSM_PPP_STATE_DONE, |
| GSM_PPP_REGISTERING, |
| GSM_PPP_ATTACHING, |
| GSM_PPP_ATTACHED, |
| GSM_PPP_SETUP_DONE, |
| GSM_PPP_STOP, |
| GSM_PPP_STATE_ERROR, |
| } state; |
| |
| const struct device *ppp_dev; |
| const struct device *at_dev; |
| const struct device *control_dev; |
| |
| struct net_if *iface; |
| |
| struct k_thread rx_thread; |
| struct k_work_q workq; |
| struct k_work_delayable rssi_work_handle; |
| struct gsm_ppp_modem_info minfo; |
| |
| enum network_state net_state; |
| |
| int retries; |
| bool modem_info_queried : 1; |
| |
| void *user_data; |
| |
| gsm_modem_power_cb modem_on_cb; |
| gsm_modem_power_cb modem_off_cb; |
| struct net_mgmt_event_callback gsm_mgmt_cb; |
| } modem; |
| |
| NET_BUF_POOL_DEFINE(gsm_recv_pool, GSM_RECV_MAX_BUF, GSM_RECV_BUF_SIZE, 0, NULL); |
| K_KERNEL_STACK_DEFINE(gsm_rx_stack, CONFIG_MODEM_GSM_RX_STACK_SIZE); |
| K_KERNEL_STACK_DEFINE(gsm_workq_stack, CONFIG_MODEM_GSM_WORKQ_STACK_SIZE); |
| |
| static inline void gsm_ppp_lock(struct gsm_modem *gsm) |
| { |
| (void)k_mutex_lock(&gsm->lock, K_FOREVER); |
| } |
| |
| static inline void gsm_ppp_unlock(struct gsm_modem *gsm) |
| { |
| (void)k_mutex_unlock(&gsm->lock); |
| } |
| |
| static inline int gsm_work_reschedule(struct k_work_delayable *dwork, k_timeout_t delay) |
| { |
| return k_work_reschedule_for_queue(&modem.workq, dwork, delay); |
| } |
| |
| #if defined(CONFIG_MODEM_GSM_ENABLE_CESQ_RSSI) |
| /* helper macro to keep readability */ |
| #define ATOI(s_, value_, desc_) modem_atoi(s_, value_, desc_, __func__) |
| |
| /** |
| * @brief Convert string to long integer, but handle errors |
| * |
| * @param s: string with representation of integer number |
| * @param err_value: on error return this value instead |
| * @param desc: name the string being converted |
| * @param func: function where this is called (typically __func__) |
| * |
| * @retval return integer conversion on success, or err_value on error |
| */ |
| static int modem_atoi(const char *s, const int err_value, |
| const char *desc, const char *func) |
| { |
| int ret; |
| char *endptr; |
| |
| ret = (int)strtol(s, &endptr, 10); |
| if ((endptr == NULL) || (*endptr != '\0')) { |
| LOG_ERR("bad %s '%s' in %s", s, |
| desc, func); |
| return err_value; |
| } |
| |
| return ret; |
| } |
| #endif |
| |
| static void gsm_rx(void *p1, void *p2, void *p3) |
| { |
| ARG_UNUSED(p2); |
| ARG_UNUSED(p3); |
| |
| struct gsm_modem *gsm = p1; |
| LOG_DBG("starting"); |
| |
| while (true) { |
| modem_iface_uart_rx_wait(&gsm->context.iface, K_FOREVER); |
| |
| /* The handler will listen AT channel */ |
| modem_cmd_handler_process(&gsm->context.cmd_handler, &gsm->context.iface); |
| } |
| } |
| |
| MODEM_CMD_DEFINE(gsm_cmd_ok) |
| { |
| (void)modem_cmd_handler_set_error(data, 0); |
| LOG_DBG("ok"); |
| k_sem_give(&modem.sem_response); |
| return 0; |
| } |
| |
| MODEM_CMD_DEFINE(gsm_cmd_error) |
| { |
| (void)modem_cmd_handler_set_error(data, -EINVAL); |
| LOG_DBG("error"); |
| k_sem_give(&modem.sem_response); |
| return 0; |
| } |
| |
| /* Handler: +CME Error: <err>[0] */ |
| MODEM_CMD_DEFINE(gsm_cmd_exterror) |
| { |
| /* TODO: map extended error codes to values */ |
| (void)modem_cmd_handler_set_error(data, -EIO); |
| k_sem_give(&modem.sem_response); |
| return 0; |
| } |
| |
| static const struct modem_cmd response_cmds[] = { |
| MODEM_CMD("OK", gsm_cmd_ok, 0U, ""), |
| MODEM_CMD("ERROR", gsm_cmd_error, 0U, ""), |
| MODEM_CMD("+CME ERROR: ", gsm_cmd_exterror, 1U, ""), |
| MODEM_CMD("CONNECT", gsm_cmd_ok, 0U, ""), |
| }; |
| |
| static int unquoted_atoi(const char *s, int base) |
| { |
| if (*s == '"') { |
| s++; |
| } |
| |
| return strtol(s, NULL, base); |
| } |
| |
| /* |
| * Handler: +COPS: <mode>[0],<format>[1],<oper>[2] |
| */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_cops) |
| { |
| if (argc >= 1) { |
| #if defined(CONFIG_MODEM_CELL_INFO) |
| if (argc >= 3) { |
| modem.context.data_operator = unquoted_atoi(argv[2], 10); |
| LOG_INF("operator: %u", |
| modem.context.data_operator); |
| } |
| #endif |
| if (unquoted_atoi(argv[0], 10) == 0) { |
| modem.context.is_automatic_oper = true; |
| } else { |
| modem.context.is_automatic_oper = false; |
| } |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * Provide modem info if modem shell is enabled. This can be shown with |
| * "modem list" shell command. |
| */ |
| |
| /* Handler: <manufacturer> */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_manufacturer) |
| { |
| size_t out_len; |
| |
| out_len = net_buf_linearize(modem.minfo.mdm_manufacturer, |
| sizeof(modem.minfo.mdm_manufacturer) - 1, |
| data->rx_buf, 0, len); |
| modem.minfo.mdm_manufacturer[out_len] = '\0'; |
| LOG_INF("Manufacturer: %s", modem.minfo.mdm_manufacturer); |
| |
| return 0; |
| } |
| |
| /* Handler: <model> */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_model) |
| { |
| size_t out_len; |
| |
| out_len = net_buf_linearize(modem.minfo.mdm_model, |
| sizeof(modem.minfo.mdm_model) - 1, |
| data->rx_buf, 0, len); |
| modem.minfo.mdm_model[out_len] = '\0'; |
| LOG_INF("Model: %s", modem.minfo.mdm_model); |
| |
| return 0; |
| } |
| |
| /* Handler: <rev> */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_revision) |
| { |
| size_t out_len; |
| |
| out_len = net_buf_linearize(modem.minfo.mdm_revision, |
| sizeof(modem.minfo.mdm_revision) - 1, |
| data->rx_buf, 0, len); |
| modem.minfo.mdm_revision[out_len] = '\0'; |
| LOG_INF("Revision: %s", modem.minfo.mdm_revision); |
| |
| return 0; |
| } |
| |
| /* Handler: <IMEI> */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_imei) |
| { |
| size_t out_len; |
| |
| out_len = net_buf_linearize(modem.minfo.mdm_imei, sizeof(modem.minfo.mdm_imei) - 1, |
| data->rx_buf, 0, len); |
| modem.minfo.mdm_imei[out_len] = '\0'; |
| LOG_INF("IMEI: %s", modem.minfo.mdm_imei); |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_MODEM_SIM_NUMBERS) |
| /* Handler: <IMSI> */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_imsi) |
| { |
| size_t out_len; |
| |
| out_len = net_buf_linearize(modem.minfo.mdm_imsi, sizeof(modem.minfo.mdm_imsi) - 1, |
| data->rx_buf, 0, len); |
| modem.minfo.mdm_imsi[out_len] = '\0'; |
| LOG_INF("IMSI: %s", modem.minfo.mdm_imsi); |
| |
| return 0; |
| } |
| |
| /* Handler: <ICCID> */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_iccid) |
| { |
| size_t out_len; |
| |
| out_len = net_buf_linearize(modem.minfo.mdm_iccid, sizeof(modem.minfo.mdm_iccid) - 1, |
| data->rx_buf, 0, len); |
| modem.minfo.mdm_iccid[out_len] = '\0'; |
| if (modem.minfo.mdm_iccid[0] == '+') { |
| /* Seen on U-blox SARA: "+CCID: nnnnnnnnnnnnnnnnnnnn". |
| * Skip over the +CCID bit, which other modems omit. |
| */ |
| char *p = strchr(modem.minfo.mdm_iccid, ' '); |
| |
| if (p) { |
| size_t iccid_len = strlen(p+1); |
| |
| (void)memmove(modem.minfo.mdm_iccid, p+1, iccid_len+1); |
| } |
| } |
| LOG_INF("ICCID: %s", modem.minfo.mdm_iccid); |
| |
| return 0; |
| } |
| #endif /* CONFIG_MODEM_SIM_NUMBERS */ |
| |
| MODEM_CMD_DEFINE(on_cmd_net_reg_sts) |
| { |
| modem.net_state = (enum network_state)atoi(argv[1]); |
| |
| switch (modem.net_state) { |
| case GSM_NET_NOT_REGISTERED: |
| LOG_DBG("Network %s.", "not registered"); |
| break; |
| case GSM_NET_HOME_NETWORK: |
| LOG_DBG("Network %s.", "registered, home network"); |
| break; |
| case GSM_NET_SEARCHING: |
| LOG_DBG("Searching for network..."); |
| break; |
| case GSM_NET_REGISTRATION_DENIED: |
| LOG_DBG("Network %s.", "registration denied"); |
| break; |
| case GSM_NET_UNKNOWN: |
| LOG_DBG("Network %s.", "unknown"); |
| break; |
| case GSM_NET_ROAMING: |
| LOG_DBG("Network %s.", "registered, roaming"); |
| break; |
| default: |
| break; |
| } |
| |
| return 0; |
| } |
| |
| #if defined(CONFIG_MODEM_CELL_INFO) |
| |
| /* |
| * Handler: +CEREG: <n>[0],<stat>[1],<tac>[2],<ci>[3],<AcT>[4] |
| */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_cereg) |
| { |
| if (argc >= 4) { |
| modem.context.data_lac = unquoted_atoi(argv[2], 16); |
| modem.context.data_cellid = unquoted_atoi(argv[3], 16); |
| LOG_INF("lac: %u, cellid: %u", |
| modem.context.data_lac, |
| modem.context.data_cellid); |
| } |
| |
| if (argc >= 5) { |
| modem.context.data_act = unquoted_atoi(argv[4], 10); |
| LOG_INF("act: %u", modem.context.data_act); |
| } |
| |
| return 0; |
| } |
| |
| static const struct setup_cmd query_cellinfo_cmds[] = { |
| SETUP_CMD_NOHANDLE("AT+CEREG=2"), |
| SETUP_CMD("AT+CEREG?", "", on_cmd_atcmdinfo_cereg, 5U, ","), |
| SETUP_CMD_NOHANDLE("AT+COPS=3,2"), |
| SETUP_CMD("AT+COPS?", "", on_cmd_atcmdinfo_cops, 3U, ","), |
| }; |
| |
| static int gsm_query_cellinfo(struct gsm_modem *gsm) |
| { |
| int ret; |
| |
| ret = modem_cmd_handler_setup_cmds_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| query_cellinfo_cmds, |
| ARRAY_SIZE(query_cellinfo_cmds), |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| if (ret < 0) { |
| LOG_WRN("modem query for cell info returned %d", ret); |
| } |
| |
| return ret; |
| } |
| #endif /* CONFIG_MODEM_CELL_INFO */ |
| |
| #if defined(CONFIG_MODEM_GSM_ENABLE_CESQ_RSSI) |
| /* |
| * Handler: +CESQ: <rxlev>[0],<ber>[1],<rscp>[2],<ecn0>[3],<rsrq>[4],<rsrp>[5] |
| */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_rssi_cesq) |
| { |
| int rsrp, rscp, rxlev; |
| |
| rsrp = ATOI(argv[5], 0, "rsrp"); |
| rscp = ATOI(argv[2], 0, "rscp"); |
| rxlev = ATOI(argv[0], 0, "rxlev"); |
| |
| if ((rsrp >= 0) && (rsrp <= 97)) { |
| modem.minfo.mdm_rssi = -140 + (rsrp - 1); |
| LOG_DBG("RSRP: %d", modem.minfo.mdm_rssi); |
| } else if ((rscp >= 0) && (rscp <= 96)) { |
| modem.minfo.mdm_rssi = -120 + (rscp - 1); |
| LOG_DBG("RSCP: %d", modem.minfo.mdm_rssi); |
| } else if ((rxlev >= 0) && (rxlev <= 63)) { |
| modem.minfo.mdm_rssi = -110 + (rxlev - 1); |
| LOG_DBG("RSSI: %d", modem.minfo.mdm_rssi); |
| } else { |
| modem.minfo.mdm_rssi = GSM_RSSI_INVALID; |
| LOG_DBG("RSRP/RSCP/RSSI not known"); |
| } |
| |
| return 0; |
| } |
| #else |
| /* Handler: +CSQ: <signal_power>[0],<qual>[1] */ |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_rssi_csq) |
| { |
| /* Expected response is "+CSQ: <signal_power>,<qual>" */ |
| if (argc > 0) { |
| int rssi = atoi(argv[0]); |
| |
| if ((rssi >= 0) && (rssi <= 31)) { |
| rssi = -113 + (rssi * 2); |
| } else { |
| rssi = GSM_RSSI_INVALID; |
| } |
| |
| modem.minfo.mdm_rssi = rssi; |
| LOG_DBG("RSSI: %d", rssi); |
| } |
| |
| return 0; |
| } |
| #endif |
| |
| #if defined(CONFIG_MODEM_GSM_ENABLE_CESQ_RSSI) |
| static const struct modem_cmd read_rssi_cmd = |
| MODEM_CMD("+CESQ:", on_cmd_atcmdinfo_rssi_cesq, 6U, ","); |
| #else |
| static const struct modem_cmd read_rssi_cmd = |
| MODEM_CMD("+CSQ:", on_cmd_atcmdinfo_rssi_csq, 2U, ","); |
| #endif |
| |
| static const struct setup_cmd setup_modem_info_cmds[] = { |
| /* query modem info */ |
| SETUP_CMD("AT+CGMI", "", on_cmd_atcmdinfo_manufacturer, 0U, ""), |
| SETUP_CMD("AT+CGMM", "", on_cmd_atcmdinfo_model, 0U, ""), |
| SETUP_CMD("AT+CGMR", "", on_cmd_atcmdinfo_revision, 0U, ""), |
| SETUP_CMD("AT+CGSN", "", on_cmd_atcmdinfo_imei, 0U, ""), |
| #if defined(CONFIG_MODEM_SIM_NUMBERS) |
| SETUP_CMD("AT+CIMI", "", on_cmd_atcmdinfo_imsi, 0U, ""), |
| SETUP_CMD("AT+CCID", "", on_cmd_atcmdinfo_iccid, 0U, ""), |
| #endif |
| }; |
| |
| static const struct setup_cmd setup_cmds[] = { |
| /* no echo */ |
| SETUP_CMD_NOHANDLE("ATE0"), |
| /* hang up */ |
| SETUP_CMD_NOHANDLE("ATH"), |
| /* extended errors in numeric form */ |
| SETUP_CMD_NOHANDLE("AT+CMEE=1"), |
| /* disable unsolicited network registration codes */ |
| SETUP_CMD_NOHANDLE("AT+CREG=0"), |
| /* create PDP context */ |
| SETUP_CMD_NOHANDLE("AT+CGDCONT=1,\"IP\",\"" CONFIG_MODEM_GSM_APN "\""), |
| #if IS_ENABLED(DT_PROP(GSM_UART_NODE, hw_flow_control)) |
| /* enable hardware flow control */ |
| SETUP_CMD_NOHANDLE("AT+IFC=2,2"), |
| #endif |
| }; |
| |
| MODEM_CMD_DEFINE(on_cmd_atcmdinfo_attached) |
| { |
| /* Expected response is "+CGATT: 0|1" so simply look for '1' */ |
| if ((argc > 0) && (atoi(argv[0]) == 1)) { |
| LOG_INF("Attached to packet service!"); |
| } |
| |
| return 0; |
| } |
| |
| |
| static const struct modem_cmd read_cops_cmd = |
| MODEM_CMD_ARGS_MAX("+COPS:", on_cmd_atcmdinfo_cops, 1U, 4U, ","); |
| |
| static const struct modem_cmd check_net_reg_cmd = |
| MODEM_CMD("+" CONFIG_MODEM_GSM_STATUS_COMMAND, on_cmd_net_reg_sts, 2U, ","); |
| |
| static const struct modem_cmd check_attached_cmd = |
| MODEM_CMD("+CGATT:", on_cmd_atcmdinfo_attached, 1U, ","); |
| |
| static const struct setup_cmd connect_cmds[] = { |
| /* connect to network */ |
| SETUP_CMD_NOHANDLE("ATD*99#"), |
| }; |
| |
| static int gsm_query_modem_info(struct gsm_modem *gsm) |
| { |
| int ret; |
| |
| if (gsm->modem_info_queried) { |
| return 0; |
| } |
| |
| ret = modem_cmd_handler_setup_cmds_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| setup_modem_info_cmds, |
| ARRAY_SIZE(setup_modem_info_cmds), |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| |
| if (ret < 0) { |
| return ret; |
| } |
| |
| gsm->modem_info_queried = true; |
| |
| return 0; |
| } |
| |
| static int gsm_setup_mccmno(struct gsm_modem *gsm) |
| { |
| int ret = 0; |
| |
| if (CONFIG_MODEM_GSM_MANUAL_MCCMNO[0] != '\0') { |
| /* use manual MCC/MNO entry */ |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| NULL, 0, |
| "AT+COPS=1,2,\"" |
| CONFIG_MODEM_GSM_MANUAL_MCCMNO |
| "\"", |
| &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| } else { |
| |
| /* First AT+COPS? is sent to check if automatic selection for operator |
| * is already enabled, if yes we do not send the command AT+COPS= 0,0. |
| */ |
| |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &read_cops_cmd, |
| 1, "AT+COPS?", |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| |
| if (ret < 0) { |
| return ret; |
| } |
| |
| if (!gsm->context.is_automatic_oper) { |
| /* register operator automatically */ |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| NULL, 0, "AT+COPS=0,0", |
| &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| } |
| } |
| |
| if (ret < 0) { |
| LOG_ERR("AT+COPS ret:%d", ret); |
| } |
| |
| return ret; |
| } |
| |
| static struct net_if *ppp_net_if(void) |
| { |
| return net_if_get_first_by_type(&NET_L2_GET_NAME(PPP)); |
| } |
| |
| static void set_ppp_carrier_on(struct gsm_modem *gsm) |
| { |
| const struct device *ppp_dev = device_get_binding(CONFIG_NET_PPP_DRV_NAME); |
| struct net_if *iface = gsm->iface; |
| |
| if (ppp_dev == NULL) { |
| LOG_ERR("Cannot find PPP %s!", CONFIG_NET_PPP_DRV_NAME); |
| return; |
| } |
| |
| net_if_up(iface); |
| } |
| |
| static void query_rssi(struct gsm_modem *gsm, bool lock) |
| { |
| int ret; |
| |
| #if defined(CONFIG_MODEM_GSM_ENABLE_CESQ_RSSI) |
| ret = modem_cmd_send_ext(&gsm->context.iface, &gsm->context.cmd_handler, &read_rssi_cmd, 1, |
| "AT+CESQ", &gsm->sem_response, GSM_CMD_SETUP_TIMEOUT, |
| lock ? 0 : MODEM_NO_TX_LOCK); |
| #else |
| ret = modem_cmd_send_ext(&gsm->context.iface, &gsm->context.cmd_handler, &read_rssi_cmd, 1, |
| "AT+CSQ", &gsm->sem_response, GSM_CMD_SETUP_TIMEOUT, |
| lock ? 0 : MODEM_NO_TX_LOCK); |
| #endif |
| |
| if (ret < 0) { |
| LOG_DBG("No answer to RSSI readout, %s", "ignoring..."); |
| } |
| } |
| |
| static inline void query_rssi_lock(struct gsm_modem *gsm) |
| { |
| query_rssi(gsm, true); |
| } |
| |
| static inline void query_rssi_nolock(struct gsm_modem *gsm) |
| { |
| query_rssi(gsm, false); |
| } |
| |
| static void rssi_handler(struct k_work *work) |
| { |
| struct k_work_delayable *dwork = k_work_delayable_from_work(work); |
| struct gsm_modem *gsm = CONTAINER_OF(dwork, struct gsm_modem, rssi_work_handle); |
| |
| gsm_ppp_lock(gsm); |
| query_rssi_lock(gsm); |
| |
| #if defined(CONFIG_MODEM_CELL_INFO) |
| (void)gsm_query_cellinfo(gsm); |
| #endif |
| (void)gsm_work_reschedule(&gsm->rssi_work_handle, |
| K_SECONDS(CONFIG_MODEM_GSM_RSSI_POLLING_PERIOD)); |
| gsm_ppp_unlock(gsm); |
| } |
| |
| static void gsm_finalize_connection(struct k_work *work) |
| { |
| int ret = 0; |
| struct k_work_delayable *dwork = k_work_delayable_from_work(work); |
| struct gsm_modem *gsm = CONTAINER_OF(dwork, struct gsm_modem, gsm_configure_work); |
| |
| gsm_ppp_lock(gsm); |
| |
| /* If already attached, jump right to RSSI readout */ |
| if (gsm->state == GSM_PPP_ATTACHED) { |
| goto attached; |
| } |
| |
| /* If attach check failed, we should not redo every setup step */ |
| if (gsm->state == GSM_PPP_ATTACHING) { |
| goto attaching; |
| } |
| |
| /* If modem is searching for network, we should skip the setup step */ |
| if (gsm->state == GSM_PPP_REGISTERING) { |
| goto registering; |
| } |
| |
| if (IS_ENABLED(CONFIG_GSM_MUX)) { |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| "AT", &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| if (ret < 0) { |
| LOG_ERR("%s returned %d, %s", "AT", ret, "retrying..."); |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, GSM_RETRY_DELAY); |
| goto unlock; |
| } |
| } |
| gsm->state = GSM_PPP_SETUP; |
| |
| if (IS_ENABLED(CONFIG_MODEM_GSM_FACTORY_RESET_AT_BOOT)) { |
| (void)modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| "AT&F", &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| (void)k_sleep(K_SECONDS(1)); |
| } |
| |
| ret = gsm_setup_mccmno(gsm); |
| if (ret < 0) { |
| LOG_ERR("%s returned %d, %s", "gsm_setup_mccmno", ret, "retrying..."); |
| |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, GSM_RETRY_DELAY); |
| goto unlock; |
| } |
| |
| ret = modem_cmd_handler_setup_cmds_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| setup_cmds, |
| ARRAY_SIZE(setup_cmds), |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| if (ret < 0) { |
| LOG_DBG("%s returned %d, %s", "setup_cmds", ret, "retrying..."); |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, GSM_RETRY_DELAY); |
| goto unlock; |
| } |
| |
| ret = gsm_query_modem_info(gsm); |
| if (ret < 0) { |
| LOG_DBG("Unable to query modem information %d", ret); |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, GSM_RETRY_DELAY); |
| goto unlock; |
| } |
| |
| gsm->state = GSM_PPP_REGISTERING; |
| registering: |
| /* Wait for cell tower registration */ |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &check_net_reg_cmd, 1, |
| "AT+" CONFIG_MODEM_GSM_STATUS_COMMAND "?", |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| if ((ret < 0) || ((gsm->net_state != GSM_NET_ROAMING) && |
| (gsm->net_state != GSM_NET_HOME_NETWORK))) { |
| if (gsm->retries == 0) { |
| gsm->retries = CONFIG_MODEM_GSM_REGISTER_TIMEOUT * |
| (MSEC_PER_SEC / GSM_REGISTER_DELAY_MSEC); |
| } else { |
| gsm->retries--; |
| } |
| |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, |
| K_MSEC(GSM_REGISTER_DELAY_MSEC)); |
| goto unlock; |
| } |
| |
| gsm->retries = 0; |
| gsm->state = GSM_PPP_ATTACHING; |
| attaching: |
| /* Don't initialize PPP until we're attached to packet service */ |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &check_attached_cmd, 1, |
| "AT+CGATT?", |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| if (ret < 0) { |
| /* |
| * retries not set -> trigger N attach retries |
| * retries set -> decrement and retry |
| * retries set, becomes 0 -> trigger full retry |
| */ |
| if (gsm->retries == 0) { |
| gsm->retries = CONFIG_MODEM_GSM_ATTACH_TIMEOUT * |
| (MSEC_PER_SEC / GSM_ATTACH_RETRY_DELAY_MSEC); |
| } else { |
| gsm->retries--; |
| } |
| |
| LOG_DBG("Not attached, %s", "retrying..."); |
| |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, |
| K_MSEC(GSM_ATTACH_RETRY_DELAY_MSEC)); |
| goto unlock; |
| } |
| |
| /* Attached, clear retry counter */ |
| LOG_DBG("modem attach returned %d, %s", ret, "read RSSI"); |
| gsm->state = GSM_PPP_ATTACHED; |
| gsm->retries = GSM_RSSI_RETRIES; |
| |
| attached: |
| |
| if (!IS_ENABLED(CONFIG_GSM_MUX)) { |
| /* Read connection quality (RSSI) before PPP carrier is ON */ |
| query_rssi_nolock(gsm); |
| |
| if (!((gsm->minfo.mdm_rssi) && (gsm->minfo.mdm_rssi != GSM_RSSI_INVALID) && |
| (gsm->minfo.mdm_rssi <= GSM_RSSI_MAXVAL))) { |
| |
| LOG_DBG("Not valid RSSI, %s", "retrying..."); |
| if (gsm->retries-- > 0) { |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, |
| K_MSEC(GSM_RSSI_RETRY_DELAY_MSEC)); |
| goto unlock; |
| } |
| } |
| #if defined(CONFIG_MODEM_CELL_INFO) |
| (void)gsm_query_cellinfo(gsm); |
| #endif |
| } |
| |
| LOG_DBG("modem RSSI: %d, %s", gsm->minfo.mdm_rssi, "enable PPP"); |
| |
| ret = modem_cmd_handler_setup_cmds_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| connect_cmds, |
| ARRAY_SIZE(connect_cmds), |
| &gsm->sem_response, |
| GSM_CMD_SETUP_TIMEOUT); |
| if (ret < 0) { |
| LOG_DBG("%s returned %d, %s", "connect_cmds", ret, "retrying..."); |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, GSM_RETRY_DELAY); |
| goto unlock; |
| } |
| |
| gsm->state = GSM_PPP_SETUP_DONE; |
| set_ppp_carrier_on(gsm); |
| |
| if (IS_ENABLED(CONFIG_GSM_MUX)) { |
| /* Re-use the original iface for AT channel */ |
| ret = modem_iface_uart_init_dev(&gsm->context.iface, |
| gsm->at_dev); |
| if (ret < 0) { |
| LOG_DBG("iface %suart error %d", "AT ", ret); |
| gsm->state = GSM_PPP_STATE_ERROR; |
| } else { |
| /* Do a test and try to send AT command to modem */ |
| ret = modem_cmd_send_nolock( |
| &gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| "AT", &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| if (ret < 0) { |
| LOG_WRN("%s returned %d, %s", "AT", ret, "iface failed"); |
| gsm->state = GSM_PPP_STATE_ERROR; |
| } else { |
| LOG_INF("AT channel %d connected to %s", |
| DLCI_AT, gsm->at_dev->name); |
| } |
| } |
| |
| modem_cmd_handler_tx_unlock(&gsm->context.cmd_handler); |
| if (gsm->state != GSM_PPP_STATE_ERROR) { |
| (void)gsm_work_reschedule(&gsm->rssi_work_handle, |
| K_SECONDS(CONFIG_MODEM_GSM_RSSI_POLLING_PERIOD)); |
| } |
| } |
| |
| unlock: |
| gsm_ppp_unlock(gsm); |
| } |
| |
| static int mux_enable(struct gsm_modem *gsm) |
| { |
| int ret; |
| |
| /* Turn on muxing */ |
| if (IS_ENABLED(CONFIG_MODEM_GSM_SIMCOM)) { |
| ret = modem_cmd_send_nolock( |
| &gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| #if defined(SIMCOM_LTE) |
| /* FIXME */ |
| /* Some SIMCOM modems can set the channels */ |
| /* Control channel always at DLCI 0 */ |
| "AT+CMUXSRVPORT=0,0;" |
| /* PPP should be at DLCI 1 */ |
| "+CMUXSRVPORT=" STRINGIFY(DLCI_PPP) ",1;" |
| /* AT should be at DLCI 2 */ |
| "+CMUXSRVPORT=" STRINGIFY(DLCI_AT) ",1;" |
| #else |
| "AT" |
| #endif |
| "+CMUX=0,0,5," |
| STRINGIFY(CONFIG_GSM_MUX_MRU_DEFAULT_LEN), |
| &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| } else if (IS_ENABLED(CONFIG_MODEM_GSM_QUECTEL)) { |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| "AT+CMUX=0,0,5," |
| STRINGIFY(CONFIG_GSM_MUX_MRU_DEFAULT_LEN), |
| &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| |
| /* Arbitrary delay for Quectel modems to initialize the CMUX, |
| * without this the AT cmd will fail. |
| */ |
| (void)k_sleep(K_SECONDS(1)); |
| } else { |
| /* Generic GSM modem */ |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| "AT+CMUX=0", &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| } |
| |
| if (ret < 0) { |
| LOG_ERR("AT+CMUX ret:%d", ret); |
| } |
| |
| return ret; |
| } |
| |
| static void mux_setup_next(struct gsm_modem *gsm) |
| { |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, K_MSEC(1)); |
| } |
| |
| static void mux_attach_cb(const struct device *mux, int dlci_address, |
| bool connected, void *user_data) |
| { |
| LOG_DBG("DLCI %d to %s %s", dlci_address, mux->name, |
| connected ? "connected" : "disconnected"); |
| |
| if (connected) { |
| uart_irq_rx_enable(mux); |
| uart_irq_tx_enable(mux); |
| } |
| |
| mux_setup_next(user_data); |
| } |
| |
| static int mux_attach(const struct device *mux, const struct device *uart, |
| int dlci_address, void *user_data) |
| { |
| int ret = uart_mux_attach(mux, uart, dlci_address, mux_attach_cb, |
| user_data); |
| if (ret < 0) { |
| LOG_ERR("Cannot attach DLCI %d (%s) to %s (%d)", dlci_address, |
| mux->name, uart->name, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void mux_setup(struct k_work *work) |
| { |
| struct k_work_delayable *dwork = k_work_delayable_from_work(work); |
| struct gsm_modem *gsm = CONTAINER_OF(dwork, struct gsm_modem, |
| gsm_configure_work); |
| const struct device *const uart = DEVICE_DT_GET(GSM_UART_NODE); |
| int ret; |
| |
| gsm_ppp_lock(gsm); |
| |
| switch (gsm->state) { |
| case GSM_PPP_STATE_CONTROL_CHANNEL: |
| /* We need to call this to reactivate mux ISR. Note: This is only called |
| * after re-initing gsm_ppp. |
| */ |
| if (gsm->ppp_dev != NULL) { |
| uart_mux_enable(gsm->ppp_dev); |
| } |
| |
| /* Get UART device. There is one dev / DLCI */ |
| if (gsm->control_dev == NULL) { |
| gsm->control_dev = uart_mux_alloc(); |
| if (gsm->control_dev == NULL) { |
| LOG_DBG("Cannot get UART mux for %s channel", |
| "control"); |
| goto fail; |
| } |
| } |
| |
| ret = mux_attach(gsm->control_dev, uart, DLCI_CONTROL, gsm); |
| if (ret < 0) { |
| goto fail; |
| } |
| |
| gsm->state = GSM_PPP_STATE_PPP_CHANNEL; |
| goto unlock; |
| |
| case GSM_PPP_STATE_PPP_CHANNEL: |
| if (gsm->ppp_dev == NULL) { |
| gsm->ppp_dev = uart_mux_alloc(); |
| if (gsm->ppp_dev == NULL) { |
| LOG_DBG("Cannot get UART mux for %s channel", |
| "PPP"); |
| goto fail; |
| } |
| } |
| |
| ret = mux_attach(gsm->ppp_dev, uart, DLCI_PPP, gsm); |
| if (ret < 0) { |
| goto fail; |
| } |
| |
| gsm->state = GSM_PPP_STATE_AT_CHANNEL; |
| goto unlock; |
| |
| case GSM_PPP_STATE_AT_CHANNEL: |
| if (gsm->at_dev == NULL) { |
| gsm->at_dev = uart_mux_alloc(); |
| if (gsm->at_dev == NULL) { |
| LOG_DBG("Cannot get UART mux for %s channel", |
| "AT"); |
| goto fail; |
| } |
| } |
| |
| ret = mux_attach(gsm->at_dev, uart, DLCI_AT, gsm); |
| if (ret < 0) { |
| goto fail; |
| } |
| |
| gsm->state = GSM_PPP_STATE_DONE; |
| goto unlock; |
| |
| case GSM_PPP_STATE_DONE: |
| /* At least the SIMCOM modem expects that the Internet |
| * connection is created in PPP channel. We will need |
| * to attach the AT channel to context iface after the |
| * PPP connection is established in order to give AT commands |
| * to the modem. |
| */ |
| ret = modem_iface_uart_init_dev(&gsm->context.iface, |
| gsm->ppp_dev); |
| if (ret < 0) { |
| LOG_DBG("iface %suart error %d", "PPP ", ret); |
| goto fail; |
| } |
| |
| LOG_INF("PPP channel %d connected to %s", |
| DLCI_PPP, gsm->ppp_dev->name); |
| |
| k_work_init_delayable(&gsm->gsm_configure_work, gsm_finalize_connection); |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, K_NO_WAIT); |
| goto unlock; |
| default: |
| __ASSERT(0, "%s while in state: %d", "mux_setup", gsm->state); |
| /* In case CONFIG_ASSERT is off, goto fail */ |
| goto fail; |
| } |
| |
| fail: |
| gsm->state = GSM_PPP_STATE_ERROR; |
| unlock: |
| gsm_ppp_unlock(gsm); |
| } |
| |
| static void gsm_configure(struct k_work *work) |
| { |
| struct k_work_delayable *dwork = k_work_delayable_from_work(work); |
| struct gsm_modem *gsm = CONTAINER_OF(dwork, struct gsm_modem, |
| gsm_configure_work); |
| int ret = -1; |
| |
| gsm_ppp_lock(gsm); |
| |
| if (gsm->state == GSM_PPP_WAIT_AT) { |
| goto wait_at; |
| } |
| |
| if (gsm->state == GSM_PPP_START) { |
| LOG_DBG("Starting modem %p configuration", gsm); |
| |
| if (gsm->modem_on_cb != NULL) { |
| gsm->modem_on_cb(gsm->dev, gsm->user_data); |
| } |
| |
| gsm->state = GSM_PPP_WAIT_AT; |
| } |
| |
| wait_at: |
| ret = modem_cmd_send_nolock(&gsm->context.iface, |
| &gsm->context.cmd_handler, |
| &response_cmds[0], |
| ARRAY_SIZE(response_cmds), |
| "AT", &gsm->sem_response, |
| GSM_CMD_AT_TIMEOUT); |
| if (ret < 0) { |
| LOG_DBG("modem not ready %d", ret); |
| goto retry; |
| } |
| |
| gsm->state = GSM_PPP_AT_RDY; |
| |
| if (IS_ENABLED(CONFIG_GSM_MUX)) { |
| if (mux_enable(gsm) == 0) { |
| LOG_DBG("GSM muxing %s", "enabled"); |
| } else { |
| LOG_DBG("GSM muxing %s", "disabled"); |
| goto retry; |
| } |
| |
| gsm->state = GSM_PPP_STATE_INIT; |
| |
| k_work_init_delayable(&gsm->gsm_configure_work, mux_setup); |
| } else { |
| k_work_init_delayable(&gsm->gsm_configure_work, gsm_finalize_connection); |
| } |
| |
| retry: |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, K_NO_WAIT); |
| gsm_ppp_unlock(gsm); |
| } |
| |
| void gsm_ppp_start(const struct device *dev) |
| { |
| int ret; |
| struct gsm_modem *gsm = dev->data; |
| |
| gsm_ppp_lock(gsm); |
| |
| if (gsm->state != GSM_PPP_STOP) { |
| LOG_ERR("gsm_ppp is already %s", "started"); |
| goto unlock; |
| } |
| |
| gsm->state = GSM_PPP_START; |
| |
| /* Re-init underlying UART comms */ |
| ret = modem_iface_uart_init_dev(&gsm->context.iface, DEVICE_DT_GET(GSM_UART_NODE)); |
| if (ret < 0) { |
| LOG_ERR("modem_iface_uart_init returned %d", ret); |
| gsm->state = GSM_PPP_STATE_ERROR; |
| goto unlock; |
| } |
| |
| k_work_init_delayable(&gsm->gsm_configure_work, gsm_configure); |
| (void)gsm_work_reschedule(&gsm->gsm_configure_work, K_NO_WAIT); |
| |
| unlock: |
| gsm_ppp_unlock(gsm); |
| } |
| |
| void gsm_ppp_stop(const struct device *dev) |
| { |
| struct gsm_modem *gsm = dev->data; |
| struct net_if *iface = gsm->iface; |
| struct k_work_sync work_sync; |
| |
| if (gsm->state == GSM_PPP_STOP) { |
| LOG_ERR("gsm_ppp is already %s", "stopped"); |
| return; |
| } |
| |
| (void)k_work_cancel_delayable_sync(&gsm->gsm_configure_work, &work_sync); |
| if (IS_ENABLED(CONFIG_GSM_MUX)) { |
| (void)k_work_cancel_delayable_sync(&gsm->rssi_work_handle, &work_sync); |
| } |
| |
| gsm_ppp_lock(gsm); |
| |
| /* wait for the interface to be properly down */ |
| if (net_if_is_up(iface)) { |
| net_if_down(ppp_net_if()); |
| (void)k_sem_take(&gsm->sem_if_down, K_FOREVER); |
| } |
| |
| if (IS_ENABLED(CONFIG_GSM_MUX)) { |
| if (gsm->ppp_dev != NULL) { |
| uart_mux_disable(gsm->ppp_dev); |
| } |
| |
| if (modem_cmd_handler_tx_lock(&gsm->context.cmd_handler, |
| GSM_CMD_LOCK_TIMEOUT) < 0) { |
| LOG_WRN("Failed locking modem cmds!"); |
| } |
| } |
| |
| if (gsm->modem_off_cb != NULL) { |
| gsm->modem_off_cb(gsm->dev, gsm->user_data); |
| } |
| |
| gsm->state = GSM_PPP_STOP; |
| gsm->net_state = GSM_NET_INIT; |
| gsm_ppp_unlock(gsm); |
| } |
| |
| void gsm_ppp_register_modem_power_callback(const struct device *dev, |
| gsm_modem_power_cb modem_on, |
| gsm_modem_power_cb modem_off, |
| void *user_data) |
| { |
| struct gsm_modem *gsm = dev->data; |
| |
| gsm_ppp_lock(gsm); |
| |
| gsm->modem_on_cb = modem_on; |
| gsm->modem_off_cb = modem_off; |
| |
| gsm->user_data = user_data; |
| gsm_ppp_unlock(gsm); |
| } |
| |
| const struct gsm_ppp_modem_info *gsm_ppp_modem_info(const struct device *dev) |
| { |
| struct gsm_modem *gsm = dev->data; |
| |
| return &gsm->minfo; |
| } |
| |
| static void gsm_mgmt_event_handler(struct net_mgmt_event_callback *cb, |
| uint32_t mgmt_event, struct net_if *iface) |
| { |
| if ((mgmt_event & NET_EVENT_IF_DOWN) != mgmt_event) { |
| return; |
| } |
| |
| /* Right now we only support 1 GSM instance */ |
| if (iface != modem.iface) { |
| return; |
| } |
| |
| if (mgmt_event == NET_EVENT_IF_DOWN) { |
| LOG_INF("GSM network interface down"); |
| /* raise semaphore to indicate the interface is down */ |
| k_sem_give(&modem.sem_if_down); |
| return; |
| } |
| } |
| |
| static int gsm_init(const struct device *dev) |
| { |
| struct gsm_modem *gsm = dev->data; |
| int ret; |
| |
| LOG_DBG("Generic GSM modem (%p)", gsm); |
| |
| (void)k_mutex_init(&gsm->lock); |
| gsm->dev = dev; |
| |
| const struct modem_cmd_handler_config cmd_handler_config = { |
| .match_buf = &gsm->cmd_match_buf[0], |
| .match_buf_len = sizeof(gsm->cmd_match_buf), |
| .buf_pool = &gsm_recv_pool, |
| .alloc_timeout = K_NO_WAIT, |
| .eol = "\r", |
| .user_data = NULL, |
| .response_cmds = response_cmds, |
| .response_cmds_len = ARRAY_SIZE(response_cmds), |
| .unsol_cmds = NULL, |
| .unsol_cmds_len = 0, |
| }; |
| |
| (void)k_sem_init(&gsm->sem_response, 0, 1); |
| (void)k_sem_init(&gsm->sem_if_down, 0, 1); |
| |
| ret = modem_cmd_handler_init(&gsm->context.cmd_handler, &gsm->cmd_handler_data, |
| &cmd_handler_config); |
| if (ret < 0) { |
| LOG_DBG("cmd handler error %d", ret); |
| return ret; |
| } |
| |
| #if defined(CONFIG_MODEM_SHELL) |
| /* modem information storage */ |
| gsm->context.data_manufacturer = gsm->minfo.mdm_manufacturer; |
| gsm->context.data_model = gsm->minfo.mdm_model; |
| gsm->context.data_revision = gsm->minfo.mdm_revision; |
| gsm->context.data_imei = gsm->minfo.mdm_imei; |
| #if defined(CONFIG_MODEM_SIM_NUMBERS) |
| gsm->context.data_imsi = gsm->minfo.mdm_imsi; |
| gsm->context.data_iccid = gsm->minfo.mdm_iccid; |
| #endif /* CONFIG_MODEM_SIM_NUMBERS */ |
| gsm->context.data_rssi = &gsm->minfo.mdm_rssi; |
| #endif /* CONFIG_MODEM_SHELL */ |
| |
| gsm->context.is_automatic_oper = false; |
| |
| const struct modem_iface_uart_config uart_config = { |
| .rx_rb_buf = &gsm->gsm_rx_rb_buf[0], |
| .rx_rb_buf_len = sizeof(gsm->gsm_rx_rb_buf), |
| .hw_flow_control = DT_PROP(GSM_UART_NODE, hw_flow_control), |
| .dev = DEVICE_DT_GET(GSM_UART_NODE), |
| }; |
| |
| ret = modem_iface_uart_init(&gsm->context.iface, &gsm->gsm_data, &uart_config); |
| if (ret < 0) { |
| LOG_DBG("iface uart error %d", ret); |
| return ret; |
| } |
| |
| ret = modem_context_register(&gsm->context); |
| if (ret < 0) { |
| LOG_DBG("context error %d", ret); |
| return ret; |
| } |
| |
| /* Initialize to stop state so that it can be started later */ |
| gsm->state = GSM_PPP_STOP; |
| |
| gsm->net_state = GSM_NET_INIT; |
| |
| LOG_DBG("iface->read %p iface->write %p", |
| gsm->context.iface.read, gsm->context.iface.write); |
| |
| (void)k_thread_create(&gsm->rx_thread, gsm_rx_stack, |
| K_KERNEL_STACK_SIZEOF(gsm_rx_stack), |
| gsm_rx, |
| gsm, NULL, NULL, K_PRIO_COOP(7), 0, K_NO_WAIT); |
| (void)k_thread_name_set(&gsm->rx_thread, "gsm_rx"); |
| |
| /* initialize the work queue */ |
| k_work_queue_init(&gsm->workq); |
| k_work_queue_start(&gsm->workq, gsm_workq_stack, K_KERNEL_STACK_SIZEOF(gsm_workq_stack), |
| K_PRIO_COOP(7), NULL); |
| (void)k_thread_name_set(&gsm->workq.thread, "gsm_workq"); |
| |
| if (IS_ENABLED(CONFIG_GSM_MUX)) { |
| k_work_init_delayable(&gsm->rssi_work_handle, rssi_handler); |
| } |
| |
| gsm->iface = ppp_net_if(); |
| if (gsm->iface == NULL) { |
| LOG_ERR("Couldn't find ppp net_if!"); |
| return -ENODEV; |
| } |
| |
| net_mgmt_init_event_callback(&gsm->gsm_mgmt_cb, gsm_mgmt_event_handler, |
| NET_EVENT_IF_DOWN); |
| net_mgmt_add_event_callback(&gsm->gsm_mgmt_cb); |
| |
| if (IS_ENABLED(CONFIG_GSM_PPP_AUTOSTART)) { |
| gsm_ppp_start(dev); |
| } |
| |
| return 0; |
| } |
| |
| DEVICE_DT_DEFINE(DT_DRV_INST(0), gsm_init, NULL, &modem, NULL, |
| POST_KERNEL, CONFIG_MODEM_GSM_INIT_PRIORITY, NULL); |