| /* |
| * Copyright (c) 2024 BayLibre |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /dts-v1/; |
| |
| #include <st/l4/stm32l4s5Xi.dtsi> |
| #include <st/l4/stm32l4s5qiix-pinctrl.dtsi> |
| |
| / { |
| model = "Analog Devices Inc. EVAL-ADIN2111EBZ board"; |
| compatible = "adi,eval-adin2111ebz"; |
| |
| chosen { |
| zephyr,console = &usart1; |
| zephyr,shell-uart = &usart1; |
| zephyr,sram = &sram0; |
| zephyr,flash = &flash0; |
| zephyr,code-partition = &slot0_partition; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| blue_led: uC_led1 { |
| gpios = <&gpiob 6 GPIO_ACTIVE_HIGH>; |
| label = "Debug led uC1"; |
| }; |
| net_red_led: led_NET1 { |
| gpios = <&gpiob 10 GPIO_ACTIVE_HIGH>; |
| label = "NET led 1"; |
| }; |
| net_green_led: led_NET2 { |
| gpios = <&gpiob 11 GPIO_ACTIVE_HIGH>; |
| label = "NET led 2"; |
| }; |
| mod_red_led: led_MOD1 { |
| gpios = <&gpioe 2 GPIO_ACTIVE_HIGH>; |
| label = "Mod led 1"; |
| }; |
| mod_green_led: led_MOD2 { |
| gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>; |
| label = "Mod led 2"; |
| }; |
| }; |
| |
| aliases { |
| led0 = &blue_led; |
| watchdog0 = &iwdg; |
| spi-flash0 = &flash_ext; |
| }; |
| }; |
| |
| &clk_lsi { |
| status = "okay"; |
| }; |
| |
| &clk_hsi48 { |
| status = "okay"; |
| }; |
| |
| &clk_hsi { |
| status = "okay"; |
| }; |
| |
| &pll { |
| div-m = <4>; |
| mul-n = <40>; |
| div-q = <2>; |
| div-r = <2>; |
| clocks = <&clk_hsi>; |
| status = "okay"; |
| }; |
| |
| &rcc { |
| clocks = <&pll>; |
| clock-frequency = <DT_FREQ_M(80)>; |
| ahb-prescaler = <1>; |
| apb1-prescaler = <1>; |
| apb2-prescaler = <1>; |
| }; |
| |
| &flash0 { |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 DT_SIZE_K(64)>; |
| read-only; |
| }; |
| |
| /* |
| * The flash starting at offset 0x10000 and ending at |
| * offset 0x1ffff is reserved for use by the application. |
| */ |
| |
| slot0_partition: partition@20000 { |
| label = "image-0"; |
| reg = <0x00020000 DT_SIZE_K(432)>; |
| }; |
| slot1_partition: partition@8c000 { |
| label = "image-1"; |
| reg = <0x0008C000 DT_SIZE_K(432)>; |
| }; |
| scratch_partition: partition@f8000 { |
| label = "image-scratch"; |
| reg = <0x000F8000 DT_SIZE_K(16)>; |
| }; |
| |
| storage_partition: partition@fc000 { |
| label = "storage"; |
| reg = <0x000fc000 DT_SIZE_K(16)>; |
| }; |
| }; |
| }; |
| |
| &iwdg { |
| status = "okay"; |
| }; |
| |
| &rng { |
| status = "okay"; |
| }; |
| |
| &dma1 { |
| status = "okay"; |
| }; |
| |
| &dmamux1 { |
| status = "okay"; |
| }; |
| |
| &usart1 { /* USB FT232 */ |
| pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa10>; |
| pinctrl-names = "default"; |
| current-speed = <115200>; |
| status = "okay"; |
| }; |
| |
| &spi1 { |
| pinctrl-0 = <&spi1_sck_pa5 &spi1_miso_pa6 &spi1_mosi_pa7>; |
| pinctrl-names = "default"; |
| cs-gpios = <&gpioa 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| status = "okay"; |
| |
| flash_ext: flash@0 { |
| compatible = "issi,is25lp128", "jedec,spi-nor"; |
| size = <134217728>; |
| jedec-id = [96 60 18]; |
| reg = <0>; |
| spi-max-frequency = <133000000>; |
| status = "okay"; |
| }; |
| }; |
| |
| &spi2 { |
| pinctrl-0 = <&spi2_sck_pb13 &spi2_miso_pb14 &spi2_mosi_pb15>; |
| pinctrl-names = "default"; |
| cs-gpios = <&gpiob 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| status = "okay"; |
| dmas = <&dmamux1 2 13 (STM32_DMA_MEMORY_TO_PERIPH | STM32_DMA_MEM_INC | |
| STM32_DMA_MEM_8BITS | STM32_DMA_PERIPH_8BITS)>, |
| <&dmamux1 3 12 (STM32_DMA_PERIPH_TO_MEMORY | STM32_DMA_MEM_INC | |
| STM32_DMA_MEM_8BITS | STM32_DMA_PERIPH_8BITS)>; |
| dma-names = "tx", "rx"; |
| |
| adin2111: adin2111@0 { |
| compatible = "adi,adin2111"; |
| reg = <0x0>; |
| spi-max-frequency = <25000000>; |
| int-gpios = <&gpioa 12 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| spi-oa; |
| spi-oa-protection; |
| |
| port1 { |
| local-mac-address = [ 00 E0 22 FE DA C9 ]; |
| }; |
| port2 { |
| local-mac-address = [ 00 E0 22 FE DA D9 ]; |
| }; |
| mdio { |
| compatible = "adi,adin2111-mdio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| ethernet-phy@1 { |
| reg = <0x1>; |
| compatible = "adi,adin2111-phy"; |
| status = "okay"; |
| }; |
| ethernet-phy@2 { |
| reg = <0x2>; |
| compatible = "adi,adin2111-phy"; |
| status = "okay"; |
| }; |
| }; |
| }; |
| }; |