| # Kconfig.nrf5 - Nordic Semiconductor nRF5 802.15.4 configuration options |
| # |
| |
| choice IEEE802154_NRF5_DRIVER_SUPPORT |
| prompt "nRF52 series IEEE 802.15.4 Driver support" |
| depends on NETWORKING && SOC_NRF52840 |
| default IEEE802154_NRF5_DISABLED |
| |
| config IEEE802154_NRF5_DISABLED |
| bool "Driver disabled" |
| |
| config IEEE802154_NRF5 |
| bool "Regular mode" |
| select NET_L2_IEEE802154 |
| select HAS_NORDIC_DRIVERS |
| |
| config IEEE802154_NRF5_RAW |
| bool "RAW mode" |
| select NET_L2_RAW_CHANNEL |
| select HAS_NORDIC_DRIVERS |
| help |
| Enable IEEE802154_CC2520 driver with RAW channel |
| |
| The CC2520 driver with RAW channel allows to export radio interface |
| over USB making an USB 802.15.4 dongle. |
| |
| endchoice |
| |
| if IEEE802154_NRF5 || IEEE802154_NRF5_RAW |
| |
| config IEEE802154_NRF5_DRV_NAME |
| string "nRF52 IEEE 802.15.4 Driver's name" |
| default "IEEE802154_nrf5" |
| help |
| This option sets the driver name |
| |
| config IEEE802154_NRF5_RX_STACK_SIZE |
| int "Driver's internal RX thread stack size" |
| default 800 |
| help |
| This option sets the driver's stack size for its internal RX thread. |
| The default value should be sufficient, but in case it proves to be |
| a too little one, this option makes it easy to play with the size. |
| |
| config IEEE802154_NRF5_INIT_PRIO |
| int "nRF52 IEEE 802.15.4 initialization priority" |
| default 80 |
| help |
| Set the initialization priority number. Do not mess with it unless |
| you know what you are doing. |
| |
| choice IEEE802154_NRF5_CCA_MODE |
| prompt "nRF52 IEEE 802.15.4 CCA mode" |
| default IEEE802154_NRF5_CCA_MODE_ED |
| help |
| CCA mode |
| |
| config IEEE802154_NRF5_CCA_MODE_ED |
| bool "Energy Above Threshold" |
| |
| config IEEE802154_NRF5_CCA_MODE_CARRIER |
| bool "Carrier Seen" |
| |
| config IEEE802154_NRF5_CCA_MODE_CARRIER_AND_ED |
| bool "Energy Above Threshold AND Carrier Seen" |
| |
| config IEEE802154_NRF5_CCA_MODE_CARRIER_OR_ED |
| bool "Energy Above Threshold OR Carrier Seen" |
| |
| endchoice |
| |
| config IEEE802154_NRF5_CCA_ED_THRESHOLD |
| int "nRF52 IEEE 802.15.4 CCA Energy Detection threshold" |
| default 45 |
| help |
| If energy detected in a given channel is above the value then the channel |
| is deemed busy. The unit is defined as per 802.15.4-2006 spec. |
| |
| config IEEE802154_NRF5_CCA_CORR_THRESHOLD |
| int "nRF52 IEEE 802.15.4 CCA Correlator threshold" |
| default 45 |
| |
| config IEEE802154_NRF5_CCA_CORR_LIMIT |
| int "nRF52 IEEE 802.15.4 CCA Correlator limit" |
| default 2 |
| help |
| Limit for occurrences above correlator threshold. When not equal to zero the |
| correlator based signal detect is enabled. |
| |
| endif |
