blob: 0fb639baa52e1efb7772b72f2eb3643b5e66bcf6 [file] [log] [blame]
# Kconfig - LIS3DH Three Axis Accelerometer configuration options
#
# Copyright (c) 2016 Intel Corporation
#
# SPDX-License-Identifier: Apache-2.0
#
menuconfig LIS3DH
bool
prompt "LIS3DH Three Axis Accelerometer"
depends on SENSOR && I2C
default n
help
Enable driver for LIS3DH I2C-based triaxial accelerometer sensor.
config LIS3DH_NAME
string
prompt "Driver name"
default "LIS3DH"
depends on LIS3DH
help
Device name with which the LIS3DH sensor is identified.
config LIS3DH_I2C_ADDR
hex
prompt "LIS3DH I2C address"
depends on LIS3DH
default 0x18
help
I2C address of the LIS3DH sensor.
0x18: Choose this option if the SDO pin is pulled to GND.
0x19: Choose this option if the SDO pin is pulled to VDDIO.
config LIS3DH_I2C_MASTER_DEV_NAME
string
prompt "I2C master where LIS3DH is connected"
depends on LIS3DH
default "I2C_0"
help
Specify the device name of the I2C master device to which LIS3DH is
connected.
choice
prompt "Trigger mode"
depends on LIS3DH
default LIS3DH_TRIGGER_GLOBAL_THREAD
help
Specify the type of triggering to be used by the driver.
config LIS3DH_TRIGGER_NONE
bool
prompt "No trigger"
config LIS3DH_TRIGGER_GLOBAL_THREAD
bool
prompt "Use global thread"
depends on GPIO
select LIS3DH_TRIGGER
config LIS3DH_TRIGGER_OWN_THREAD
bool
prompt "Use own thread"
depends on GPIO
select LIS3DH_TRIGGER
endchoice
config LIS3DH_TRIGGER
bool
depends on LIS3DH
config LIS3DH_GPIO_DEV_NAME
string
prompt "GPIO device"
default "GPIO_0"
depends on LIS3DH && LIS3DH_TRIGGER
help
The device name of the GPIO device to which the LIS3DH interrupt pins
are connected.
config LIS3DH_GPIO_PIN_NUM
int
prompt "Interrupt GPIO pin number"
default 0
depends on LIS3DH && LIS3DH_TRIGGER
help
The number of the GPIO on which the interrupt signal from the LIS3DH
chip will be received.
config LIS3DH_THREAD_PRIORITY
int
prompt "Thread priority"
depends on LIS3DH && LIS3DH_TRIGGER_OWN_THREAD
default 10
help
Priority of thread used by the driver to handle interrupts.
config LIS3DH_THREAD_STACK_SIZE
int
prompt "Thread stack size"
depends on LIS3DH && LIS3DH_TRIGGER_OWN_THREAD
default 1024
help
Stack size of thread used by the driver to handle interrupts.
choice
prompt "Acceleration measurement range"
depends on LIS3DH
default LIS3DH_ACCEL_RANGE_2G
help
Measurement full scale range for acceleration values.
config LIS3DH_ACCEL_RANGE_2G
bool
prompt "+/-2g"
config LIS3DH_ACCEL_RANGE_4G
bool
prompt "+/-4g"
config LIS3DH_ACCEL_RANGE_8G
bool
prompt "+/-8g"
config LIS3DH_ACCEL_RANGE_16G
bool
prompt "+/-16g"
endchoice
choice
prompt "Power mode"
depends on LIS3DH
default LIS3DH_POWER_MODE_NORMAL
help
Choose between normal or low power operation mode for chip.
config LIS3DH_POWER_MODE_NORMAL
bool
prompt "normal"
config LIS3DH_POWER_MODE_LOW
bool
prompt "low"
endchoice
choice
prompt "Data rate frequency"
depends on LIS3DH
default LIS3DH_ODR_1
help
Data rate frequency of acceleration data.
config LIS3DH_ODR_1
bool
prompt "1Hz"
config LIS3DH_ODR_2
bool
prompt "10Hz"
config LIS3DH_ODR_3
bool
prompt "25Hz"
config LIS3DH_ODR_4
bool
prompt "50Hz"
config LIS3DH_ODR_5
bool
prompt "100Hz"
config LIS3DH_ODR_6
bool
prompt "200Hz"
config LIS3DH_ODR_7
bool
prompt "400Hz"
config LIS3DH_ODR_8
bool
prompt "1.6KHz"
depends on LIS3DH_POWER_MODE_LOW
config LIS3DH_ODR_9_NORMAL
bool
prompt "1.25KHz"
depends on LIS3DH_POWER_MODE_NORMAL
config LIS3DH_ODR_9_LOW
bool
prompt "5KHz"
depends on LIS3DH_POWER_MODE_LOW
endchoice