blob: 400dc8b9d9e5666cea4f65fa041527c5970a4196 [file] [log] [blame]
/*
* Copyright (c) 2020 PHYTEC Messtechnik GmbH
* Copyright (c) 2021 Nordic Semiconductor ASA
*
* SPDX-License-Identifier: Apache-2.0
*/
/*
* Client API in this file is based on mbm_core.c from uC/Modbus Stack.
*
* uC/Modbus
* The Embedded Modbus Stack
*
* Copyright 2003-2020 Silicon Laboratories Inc. www.silabs.com
*
* SPDX-License-Identifier: APACHE-2.0
*
* This software is subject to an open source license and is distributed by
* Silicon Laboratories Inc. pursuant to the terms of the Apache License,
* Version 2.0 available at www.apache.org/licenses/LICENSE-2.0.
*/
/**
* @brief MODBUS transport protocol API
* @defgroup modbus MODBUS
* @ingroup io_interfaces
* @{
*/
#ifndef ZEPHYR_INCLUDE_MODBUS_H_
#define ZEPHYR_INCLUDE_MODBUS_H_
#include <drivers/uart.h>
#ifdef __cplusplus
extern "C" {
#endif
/** Length of MBAP Header */
#define MODBUS_MBAP_LENGTH 7
/** Length of MBAP Header plus function code */
#define MODBUS_MBAP_AND_FC_LENGTH (MODBUS_MBAP_LENGTH + 1)
/**
* @brief Frame struct used internally and for raw ADU support.
*/
struct modbus_adu {
/** Transaction Identifier */
uint16_t trans_id;
/** Protocol Identifier */
uint16_t proto_id;
/** Length of the data only (not the length of unit ID + PDU) */
uint16_t length;
/** Unit Identifier */
uint8_t unit_id;
/** Function Code */
uint8_t fc;
/** Transaction Data */
uint8_t data[CONFIG_MODBUS_BUFFER_SIZE - 4];
/** RTU CRC */
uint16_t crc;
};
/**
* @brief Coil read (FC01)
*
* Sends a Modbus message to read the status of coils from a server.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Coil starting address
* @param coil_tbl Pointer to an array of bytes containing the value
* of the coils read.
* The format is:
*
* MSB LSB
* B7 B6 B5 B4 B3 B2 B1 B0
* -------------------------------------
* coil_tbl[0] #8 #7 #1
* coil_tbl[1] #16 #15 #9
* :
* :
*
* Note that the array that will be receiving the coil
* values must be greater than or equal to:
* (num_coils - 1) / 8 + 1
* @param num_coils Quantity of coils to read
*
* @retval 0 If the function was successful
*/
int modbus_read_coils(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
uint8_t *const coil_tbl,
const uint16_t num_coils);
/**
* @brief Read discrete inputs (FC02)
*
* Sends a Modbus message to read the status of discrete inputs from
* a server.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Discrete input starting address
* @param di_tbl Pointer to an array that will receive the state
* of the discrete inputs.
* The format of the array is as follows:
*
* MSB LSB
* B7 B6 B5 B4 B3 B2 B1 B0
* -------------------------------------
* di_tbl[0] #8 #7 #1
* di_tbl[1] #16 #15 #9
* :
* :
*
* Note that the array that will be receiving the discrete
* input values must be greater than or equal to:
* (num_di - 1) / 8 + 1
* @param num_di Quantity of discrete inputs to read
*
* @retval 0 If the function was successful
*/
int modbus_read_dinputs(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
uint8_t *const di_tbl,
const uint16_t num_di);
/**
* @brief Read holding registers (FC03)
*
* Sends a Modbus message to read the value of holding registers
* from a server.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Register starting address
* @param reg_buf Is a pointer to an array that will receive
* the current values of the holding registers from
* the server. The array pointed to by 'reg_buf' needs
* to be able to hold at least 'num_regs' entries.
* @param num_regs Quantity of registers to read
*
* @retval 0 If the function was successful
*/
int modbus_read_holding_regs(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
uint16_t *const reg_buf,
const uint16_t num_regs);
/**
* @brief Read input registers (FC04)
*
* Sends a Modbus message to read the value of input registers from
* a server.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Register starting address
* @param reg_buf Is a pointer to an array that will receive
* the current value of the holding registers
* from the server. The array pointed to by 'reg_buf'
* needs to be able to hold at least 'num_regs' entries.
* @param num_regs Quantity of registers to read
*
* @retval 0 If the function was successful
*/
int modbus_read_input_regs(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
uint16_t *const reg_buf,
const uint16_t num_regs);
/**
* @brief Write single coil (FC05)
*
* Sends a Modbus message to write the value of single coil to a server.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param coil_addr Coils starting address
* @param coil_state Is the desired state of the coil
*
* @retval 0 If the function was successful
*/
int modbus_write_coil(const int iface,
const uint8_t unit_id,
const uint16_t coil_addr,
const bool coil_state);
/**
* @brief Write single holding register (FC06)
*
* Sends a Modbus message to write the value of single holding register
* to a server unit.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Coils starting address
* @param reg_val Desired value of the holding register
*
* @retval 0 If the function was successful
*/
int modbus_write_holding_reg(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
const uint16_t reg_val);
/**
* @brief Read diagnostic (FC08)
*
* Sends a Modbus message to perform a diagnostic function of a server unit.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param sfunc Diagnostic sub-function code
* @param data Sub-function data
* @param data_out Pointer to the data value
*
* @retval 0 If the function was successful
*/
int modbus_request_diagnostic(const int iface,
const uint8_t unit_id,
const uint16_t sfunc,
const uint16_t data,
uint16_t *const data_out);
/**
* @brief Write coils (FC15)
*
* Sends a Modbus message to write to coils on a server unit.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Coils starting address
* @param coil_tbl Pointer to an array of bytes containing the value
* of the coils to write.
* The format is:
*
* MSB LSB
* B7 B6 B5 B4 B3 B2 B1 B0
* -------------------------------------
* coil_tbl[0] #8 #7 #1
* coil_tbl[1] #16 #15 #9
* :
* :
*
* Note that the array that will be receiving the coil
* values must be greater than or equal to:
* (num_coils - 1) / 8 + 1
* @param num_coils Quantity of coils to write
*
* @retval 0 If the function was successful
*/
int modbus_write_coils(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
uint8_t *const coil_tbl,
const uint16_t num_coils);
/**
* @brief Write holding registers (FC16)
*
* Sends a Modbus message to write to integer holding registers
* to a server unit.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Register starting address
* @param reg_buf Is a pointer to an array containing
* the value of the holding registers to write.
* Note that the array containing the register values must
* be greater than or equal to 'num_regs'
* @param num_regs Quantity of registers to write
*
* @retval 0 If the function was successful
*/
int modbus_write_holding_regs(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
uint16_t *const reg_buf,
const uint16_t num_regs);
/**
* @brief Read floating-point holding registers (FC03)
*
* Sends a Modbus message to read the value of floating-point
* holding registers from a server unit.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Register starting address
* @param reg_buf Is a pointer to an array that will receive
* the current values of the holding registers from
* the server. The array pointed to by 'reg_buf' needs
* to be able to hold at least 'num_regs' entries.
* @param num_regs Quantity of registers to read
*
* @retval 0 If the function was successful
*/
int modbus_read_holding_regs_fp(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
float *const reg_buf,
const uint16_t num_regs);
/**
* @brief Write floating-point holding registers (FC16)
*
* Sends a Modbus message to write to floating-point holding registers
* to a server unit.
*
* @param iface Modbus interface index
* @param unit_id Modbus unit ID of the server
* @param start_addr Register starting address
* @param reg_buf Is a pointer to an array containing
* the value of the holding registers to write.
* Note that the array containing the register values must
* be greater than or equal to 'num_regs'
* @param num_regs Quantity of registers to write
*
* @retval 0 If the function was successful
*/
int modbus_write_holding_regs_fp(const int iface,
const uint8_t unit_id,
const uint16_t start_addr,
float *const reg_buf,
const uint16_t num_regs);
/** Modbus Server User Callback structure */
struct modbus_user_callbacks {
/** Coil read callback */
int (*coil_rd)(uint16_t addr, bool *state);
/** Coil write callback */
int (*coil_wr)(uint16_t addr, bool state);
/** Discrete Input read callback */
int (*discrete_input_rd)(uint16_t addr, bool *state);
/** Input Register read callback */
int (*input_reg_rd)(uint16_t addr, uint16_t *reg);
/** Floating Point Input Register read callback */
int (*input_reg_rd_fp)(uint16_t addr, float *reg);
/** Holding Register read callback */
int (*holding_reg_rd)(uint16_t addr, uint16_t *reg);
/** Holding Register write callback */
int (*holding_reg_wr)(uint16_t addr, uint16_t reg);
/** Floating Point Holding Register read callback */
int (*holding_reg_rd_fp)(uint16_t addr, float *reg);
/** Floating Point Holding Register write callback */
int (*holding_reg_wr_fp)(uint16_t addr, float reg);
};
/**
* @brief Get Modbus interface index according to interface name
*
* If there is more than one interface, it can be used to clearly
* identify interfaces in the application.
*
* @param iface_name Modbus interface name
*
* @retval Modbus interface index or negative error value.
*/
int modbus_iface_get_by_name(const char *iface_name);
/**
* @brief ADU raw callback function signature
*
* @param iface Modbus RTU interface index
* @param adu Pointer to the RAW ADU struct to send
*
* @retval 0 If transfer was successful
*/
typedef int (*modbus_raw_cb_t)(const int iface, const struct modbus_adu *adu);
/**
* @brief Modbus interface mode
*/
enum modbus_mode {
/** Modbus over serial line RTU mode */
MODBUS_MODE_RTU,
/** Modbus over serial line ASCII mode */
MODBUS_MODE_ASCII,
/** Modbus raw ADU mode */
MODBUS_MODE_RAW,
};
/**
* @brief Modbus serial line parameter
*/
struct modbus_serial_param {
/** Baudrate of the serial line */
uint32_t baud;
/** parity UART's parity setting:
* UART_CFG_PARITY_NONE,
* UART_CFG_PARITY_EVEN,
* UART_CFG_PARITY_ODD
*/
enum uart_config_parity parity;
};
/**
* @brief Modbus server parameter
*/
struct modbus_server_param {
/** Pointer to the User Callback structure */
struct modbus_user_callbacks *user_cb;
/** Modbus unit ID of the server */
uint8_t unit_id;
};
/**
* @brief User parameter structure to configure Modbus interfase
* as client or server.
*/
struct modbus_iface_param {
/** Mode of the interface */
enum modbus_mode mode;
union {
struct modbus_server_param server;
/** Amount of time client will wait for
* a response from the server.
*/
uint32_t rx_timeout;
};
union {
/** Serial support parameter of the interface */
struct modbus_serial_param serial;
/** Pointer to raw ADU callback function */
modbus_raw_cb_t raw_tx_cb;
};
};
/**
* @brief Configure Modbus Interface as raw ADU server
*
* @param iface Modbus RTU interface index
* @param param Configuration parameter of the server interface
*
* @retval 0 If the function was successful
*/
int modbus_init_server(const int iface, struct modbus_iface_param param);
/**
* @brief Configure Modbus Interface as raw ADU client
*
* @param iface Modbus RTU interface index
* @param param Configuration parameter of the client interface
*
* @retval 0 If the function was successful
*/
int modbus_init_client(const int iface, struct modbus_iface_param param);
/**
* @brief Disable Modbus Interface
*
* This function is called to disable Modbus interface.
*
* @param iface Modbus interface index
*
* @retval 0 If the function was successful
*/
int modbus_disable(const uint8_t iface);
/**
* @brief Submit raw ADU
*
* @param iface Modbus RTU interface index
* @param adu Pointer to the RAW ADU struct that is received
*
* @retval 0 If transfer was successful
*/
int modbus_raw_submit_rx(const int iface, const struct modbus_adu *adu);
/**
* @brief Put MBAP header into a buffer
*
* @param adu Pointer to the RAW ADU struct
* @param header Pointer to the buffer in which MBAP header
* will be placed.
*
* @retval 0 If transfer was successful
*/
void modbus_raw_put_header(const struct modbus_adu *adu, uint8_t *header);
/**
* @brief Get MBAP header from a buffer
*
* @param adu Pointer to the RAW ADU struct
* @param header Pointer to the buffer containing MBAP header
*
* @retval 0 If transfer was successful
*/
void modbus_raw_get_header(struct modbus_adu *adu, const uint8_t *header);
/**
* @brief Set Server Device Failure exception
*
* This function modifies ADU passed by the pointer.
*
* @param adu Pointer to the RAW ADU struct
*/
void modbus_raw_set_server_failure(struct modbus_adu *adu);
/**
* @brief Use interface as backend to send and receive ADU
*
* This function overwrites ADU passed by the pointer and generates
* exception responses if backend interface is misconfigured or
* target device is unreachable.
*
* @param iface Modbus client interface index
* @param adu Pointer to the RAW ADU struct
*
* @retval 0 If transfer was successful
*/
int modbus_raw_backend_txn(const int iface, struct modbus_adu *adu);
#ifdef __cplusplus
}
#endif
/**
* @}
*/
#endif /* ZEPHYR_INCLUDE_MODBUS_H_ */