| # Kconfig - STM32 I2S driver configuration options |
| # |
| # Copyright (c) 2018 STMicroelectronics |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| menuconfig I2S_STM32 |
| bool "STM32 MCU I2S controller driver" |
| depends on SOC_SERIES_STM32F4X |
| select DMA |
| help |
| Enable I2S support on the STM32 family of processors. |
| (Tested on the STM32F4 series) |
| |
| if I2S_STM32 |
| |
| config I2S_STM32_RX_BLOCK_COUNT |
| int "RX queue length" |
| default 4 |
| |
| config I2S_STM32_TX_BLOCK_COUNT |
| int "TX queue length" |
| default 4 |
| |
| config I2S_STM32_USE_PLLI2S_ENABLE |
| bool "Enable usage of PLL" |
| help |
| Enable it if I2S clock should be provided by the PLLI2S. |
| If not enabled the clock will be provided by HSI/HSE. |
| |
| config I2S_STM32_PLLI2S_PLLM |
| int "Division factor for PLLI2S VCO input clock" |
| depends on I2S_STM32_USE_PLLI2S_ENABLE |
| default 8 |
| range 2 63 |
| help |
| Division factor for the audio PLL (PLLI2S) VCO input clock. |
| PLLM factor should be selected to ensure that the VCO |
| input frequency ranges from 1 to 2 MHz. It is recommended |
| to select a frequency of 2 MHz to limit PLL jitter. |
| Allowed values: 2-63 |
| |
| config I2S_STM32_PLLI2S_PLLN |
| int "Multiplier factor for PLLI2S VCO output clock" |
| depends on I2S_STM32_USE_PLLI2S_ENABLE |
| default 56 |
| range 50 432 |
| help |
| Multiply factor for the audio PLL (PLLI2S) VCO output clock. |
| PLLN factor should be selected to ensure that the VCO |
| output frequency ranges from 100 to 432 MHz. |
| Allowed values: 50-432 |
| |
| config I2S_STM32_PLLI2S_PLLR |
| int "Division factor for I2S clock" |
| depends on I2S_STM32_USE_PLLI2S_ENABLE |
| default 7 |
| range 2 7 |
| help |
| Division factor for the I2S clock. |
| PLLR factor should be selected to ensure that the I2S clock |
| frequency is less than or equal to 192MHz. |
| Allowed values: 2-7 |
| |
| config I2S_1 |
| bool "I2S port 1" |
| help |
| Enable I2S controller port 1. |
| |
| config I2S_2 |
| bool "I2S port 2" |
| help |
| Enable I2S controller port 2. |
| |
| config I2S_3 |
| bool "I2S port 3" |
| help |
| Enable I2S controller port 3. |
| |
| config I2S_4 |
| bool "I2S port 4" |
| help |
| Enable I2S controller port 4. |
| |
| config I2S_5 |
| bool "I2S port 5" |
| help |
| Enable I2S controller port 5. |
| |
| endif # I2S_STM32 |
