| # Copyright (c) 2021 Argentum Systems Ltd. |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if SOC_SERIES_SAML21 || SOC_SERIES_SAMR34 || SOC_SERIES_SAMR35 |
| |
| config SOC_ATMEL_SAML_DEBUG_PAUSE |
| bool "Insert a pause at boot, to allow a debugger to attach" |
| default y |
| help |
| Issues have been observed while attempting to attach a debugger. |
| These can be mitigated by inserting a small delay during the early boot |
| sequence, before the system clock is configured. |
| |
| If you ever intend to attach a debugger, say y. |
| If you are confident that you will never attach a debugger to the |
| resulting binary, or require the best possible boot time, say n. |
| |
| config SOC_ATMEL_SAML_OSC32K |
| bool "Internal 32.768 kHz RC oscillator" |
| help |
| Eable the internal 32.768 kHz RC oscillator at startup. |
| This can then be selected as the main clock reference for the SOC. |
| |
| config SOC_ATMEL_SAML_XOSC32K |
| bool "External 32.768 kHz clock source" |
| help |
| Enable the external 32.768 kHz cloud source at startup. |
| This can then be selected as the main clock reference for the SOC. |
| |
| config SOC_ATMEL_SAML_XOSC32K_CRYSTAL |
| bool "External 32.768 kHz clock is a crystal oscillator" |
| depends on SOC_ATMEL_SAML_XOSC32K |
| default y |
| help |
| Enable the crystal oscillator (if disabled, expect a clock signal on |
| XIN32). |
| |
| config SOC_ATMEL_SAML_OSC16M |
| bool "Internal 16 MHz RC oscillator" |
| help |
| Enable the internal 16 MHz RC oscillator at startup. |
| This can then be selected as the main clock reference for the SOC. |
| |
| # NOTE: XOSC is not currently supported |
| |
| |
| choice |
| prompt "Main clock reference" |
| default SOC_ATMEL_SAML_OPENLOOP_AS_MAIN |
| help |
| Selects the clock that will be used for the DFLL48M's reference. |
| Main clocks, such as the CPU and AHB clocks will be derived from |
| DFLL48M configured for 48 MHz. |
| |
| config SOC_ATMEL_SAML_OPENLOOP_AS_MAIN |
| bool "OPENLOOP" |
| help |
| Note, this mode can only be used with an LDO regulator. |
| |
| config SOC_ATMEL_SAML_OSC32K_AS_MAIN |
| bool "OSC32K" |
| depends on SOC_ATMEL_SAML_OSC32K |
| |
| config SOC_ATMEL_SAML_XOSC32K_AS_MAIN |
| bool "XOSC32K" |
| depends on SOC_ATMEL_SAML_XOSC32K |
| |
| config SOC_ATMEL_SAML_OSC16M_AS_MAIN |
| bool "OSC16M" |
| depends on SOC_ATMEL_SAML_OSC16M |
| |
| endchoice |
| |
| config SOC_ATMEL_SAMR3X_RADIO_OFF_SETUP |
| bool "Configure LoRa radio pins if not in use" |
| default y if !LORA |
| depends on SOC_SERIES_SAMR34 || SOC_SERIES_SAMR35 |
| help |
| As detailed in DS70005356C, LoRa radio SPI pins do not have pull-ups, |
| so when the radio is not in use, it's important that CS is kept high, |
| to avoid unexpected behavior and increased current consumption. To |
| further reduce power consumption, radio can be kept in reset state by |
| keeping nRST pin low. When enabling this option, both CS and nRST will |
| be configured high and low, respectively. |
| |
| endif # SOC_SERIES_SAML21 || SOC_SERIES_SAMR34 || SOC_SERIES_SAMR35 |
