| /* | 
 |  * Copyright (c) 2017, I-SENSE group of ICCS | 
 |  * Copyright (c) 2017 Linaro Ltd | 
 |  * | 
 |  * SPDX-License-Identifier: Apache-2.0 | 
 |  * | 
 |  * I2C Driver for: STM32F1, STM32F2, STM32F4 and STM32L1 | 
 |  * | 
 |  */ | 
 |  | 
 | #include <zephyr/drivers/clock_control/stm32_clock_control.h> | 
 | #include <zephyr/drivers/clock_control.h> | 
 | #include <zephyr/sys/util.h> | 
 | #include <zephyr/kernel.h> | 
 | #include <soc.h> | 
 | #include <stm32_ll_i2c.h> | 
 | #include <errno.h> | 
 | #include <zephyr/drivers/i2c.h> | 
 | #include "i2c_ll_stm32.h" | 
 |  | 
 | #define LOG_LEVEL CONFIG_I2C_LOG_LEVEL | 
 | #include <zephyr/logging/log.h> | 
 | LOG_MODULE_REGISTER(i2c_ll_stm32_v1); | 
 |  | 
 | #include "i2c-priv.h" | 
 |  | 
 | #define STM32_I2C_TRANSFER_TIMEOUT_MSEC  500 | 
 |  | 
 | #define STM32_I2C_TIMEOUT_USEC  1000 | 
 | #define I2C_REQUEST_WRITE       0x00 | 
 | #define I2C_REQUEST_READ        0x01 | 
 | #define HEADER                  0xF0 | 
 |  | 
 | static void stm32_i2c_generate_start_condition(I2C_TypeDef *i2c) | 
 | { | 
 | 	uint16_t cr1 = LL_I2C_ReadReg(i2c, CR1); | 
 |  | 
 | 	if (cr1 & I2C_CR1_STOP) { | 
 | 		LOG_DBG("%s: START while STOP active!", __func__); | 
 | 		LL_I2C_WriteReg(i2c, CR1, cr1 & ~I2C_CR1_STOP); | 
 | 	} | 
 |  | 
 | 	LL_I2C_GenerateStartCondition(i2c); | 
 | } | 
 |  | 
 | #ifdef CONFIG_I2C_STM32_INTERRUPT | 
 |  | 
 | static void stm32_i2c_disable_transfer_interrupts(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	LL_I2C_DisableIT_TX(i2c); | 
 | 	LL_I2C_DisableIT_RX(i2c); | 
 | 	LL_I2C_DisableIT_EVT(i2c); | 
 | 	LL_I2C_DisableIT_BUF(i2c); | 
 |  | 
 | 	if (!data->smbalert_active) { | 
 | 		LL_I2C_DisableIT_ERR(i2c); | 
 | 	} | 
 | } | 
 |  | 
 | static void stm32_i2c_enable_transfer_interrupts(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	LL_I2C_EnableIT_ERR(i2c); | 
 | 	LL_I2C_EnableIT_EVT(i2c); | 
 | 	LL_I2C_EnableIT_BUF(i2c); | 
 | } | 
 |  | 
 | #endif /* CONFIG_I2C_STM32_INTERRUPT */ | 
 |  | 
 | static void stm32_i2c_reset(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 | 	uint16_t cr1, cr2, oar1, oar2, trise, ccr; | 
 | #if defined(I2C_FLTR_ANOFF) && defined(I2C_FLTR_DNF) | 
 | 	uint16_t fltr; | 
 | #endif | 
 |  | 
 | 	/* disable i2c and disable IRQ's */ | 
 | 	LL_I2C_Disable(i2c); | 
 | #ifdef CONFIG_I2C_STM32_INTERRUPT | 
 | 	stm32_i2c_disable_transfer_interrupts(dev); | 
 | #endif | 
 |  | 
 | 	/* save all important registers before reset */ | 
 | 	cr1 = LL_I2C_ReadReg(i2c, CR1); | 
 | 	cr2 = LL_I2C_ReadReg(i2c, CR2); | 
 | 	oar1 = LL_I2C_ReadReg(i2c, OAR1); | 
 | 	oar2 = LL_I2C_ReadReg(i2c, OAR2); | 
 | 	ccr = LL_I2C_ReadReg(i2c, CCR); | 
 | 	trise = LL_I2C_ReadReg(i2c, TRISE); | 
 | #if defined(I2C_FLTR_ANOFF) && defined(I2C_FLTR_DNF) | 
 | 	fltr = LL_I2C_ReadReg(i2c, FLTR); | 
 | #endif | 
 |  | 
 | 	/* reset i2c hardware */ | 
 | 	LL_I2C_EnableReset(i2c); | 
 | 	LL_I2C_DisableReset(i2c); | 
 |  | 
 | 	/* restore all important registers after reset */ | 
 | 	LL_I2C_WriteReg(i2c, CR1, cr1); | 
 | 	LL_I2C_WriteReg(i2c, CR2, cr2); | 
 |  | 
 | 	/* bit 14 of OAR1 must always be 1 */ | 
 | 	oar1 |= (1 << 14); | 
 | 	LL_I2C_WriteReg(i2c, OAR1, oar1); | 
 | 	LL_I2C_WriteReg(i2c, OAR2, oar2); | 
 | 	LL_I2C_WriteReg(i2c, CCR, ccr); | 
 | 	LL_I2C_WriteReg(i2c, TRISE, trise); | 
 | #if defined(I2C_FLTR_ANOFF) && defined(I2C_FLTR_DNF) | 
 | 	LL_I2C_WriteReg(i2c, FLTR, fltr); | 
 | #endif | 
 | } | 
 |  | 
 |  | 
 | static void stm32_i2c_master_finish(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | #ifdef CONFIG_I2C_STM32_INTERRUPT | 
 | 	stm32_i2c_disable_transfer_interrupts(dev); | 
 | #endif | 
 |  | 
 | #if defined(CONFIG_I2C_TARGET) | 
 | 	data->master_active = false; | 
 | 	if (!data->slave_attached && !data->smbalert_active) { | 
 | 		LL_I2C_Disable(i2c); | 
 | 	} else { | 
 | 		stm32_i2c_enable_transfer_interrupts(dev); | 
 | 		LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); | 
 | 	} | 
 | #else | 
 | 	if (!data->smbalert_active) { | 
 | 		LL_I2C_Disable(i2c); | 
 | 	} | 
 | #endif | 
 | } | 
 |  | 
 | static inline void msg_init(const struct device *dev, struct i2c_msg *msg, | 
 | 			    uint8_t *next_msg_flags, uint16_t slave, | 
 | 			    uint32_t transfer) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	ARG_UNUSED(next_msg_flags); | 
 |  | 
 | #ifdef CONFIG_I2C_STM32_INTERRUPT | 
 | 	k_sem_reset(&data->device_sync_sem); | 
 | #endif | 
 |  | 
 | 	data->current.len = msg->len; | 
 | 	data->current.buf = msg->buf; | 
 | 	data->current.flags = msg->flags; | 
 | 	data->current.is_restart = 0U; | 
 | 	data->current.is_write = (transfer == I2C_REQUEST_WRITE); | 
 | 	data->current.is_arlo = 0U; | 
 | 	data->current.is_err = 0U; | 
 | 	data->current.is_nack = 0U; | 
 | 	data->current.msg = msg; | 
 | #if defined(CONFIG_I2C_TARGET) | 
 | 	data->master_active = true; | 
 | #endif | 
 | 	data->slave_address = slave; | 
 |  | 
 | 	LL_I2C_Enable(i2c); | 
 |  | 
 | 	LL_I2C_DisableBitPOS(i2c); | 
 | 	LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); | 
 | 	if (msg->flags & I2C_MSG_RESTART) { | 
 | 		stm32_i2c_generate_start_condition(i2c); | 
 | 	} | 
 | } | 
 |  | 
 | static int32_t msg_end(const struct device *dev, uint8_t *next_msg_flags, | 
 | 		       const char *funcname) | 
 | { | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 |  | 
 | 	if (data->current.is_nack || data->current.is_err || | 
 | 	    data->current.is_arlo) { | 
 | 		goto error; | 
 | 	} | 
 |  | 
 | 	if (!next_msg_flags) { | 
 | 		stm32_i2c_master_finish(dev); | 
 | 	} | 
 |  | 
 | 	return 0; | 
 |  | 
 | error: | 
 | 	if (data->current.is_arlo) { | 
 | 		LOG_DBG("%s: ARLO %d", funcname, | 
 | 			data->current.is_arlo); | 
 | 		data->current.is_arlo = 0U; | 
 | 	} | 
 |  | 
 | 	if (data->current.is_nack) { | 
 | 		LOG_DBG("%s: NACK", funcname); | 
 | 		data->current.is_nack = 0U; | 
 | 	} | 
 |  | 
 | 	if (data->current.is_err) { | 
 | 		LOG_DBG("%s: ERR %d", funcname, | 
 | 			data->current.is_err); | 
 | 		data->current.is_err = 0U; | 
 | 	} | 
 | 	stm32_i2c_master_finish(dev); | 
 |  | 
 | 	return -EIO; | 
 | } | 
 |  | 
 | #ifdef CONFIG_I2C_STM32_INTERRUPT | 
 |  | 
 | static void stm32_i2c_master_mode_end(const struct device *dev) | 
 | { | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 |  | 
 | 	k_sem_give(&data->device_sync_sem); | 
 | } | 
 |  | 
 | static inline void handle_sb(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	uint16_t saddr = data->slave_address; | 
 | 	uint8_t slave; | 
 |  | 
 | 	if (I2C_ADDR_10_BITS & data->dev_config) { | 
 | 		slave = (((saddr & 0x0300) >> 7) & 0xFF); | 
 | 		uint8_t header = slave | HEADER; | 
 |  | 
 | 		if (data->current.is_restart == 0U) { | 
 | 			data->current.is_restart = 1U; | 
 | 		} else { | 
 | 			header |= I2C_REQUEST_READ; | 
 | 			data->current.is_restart = 0U; | 
 | 		} | 
 | 		LL_I2C_TransmitData8(i2c, header); | 
 |  | 
 | 		return; | 
 | 	} | 
 | 	slave = (saddr << 1) & 0xFF; | 
 | 	if (data->current.is_write) { | 
 | 		LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_WRITE); | 
 | 	} else { | 
 | 		LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_READ); | 
 | 		if (data->current.len == 2) { | 
 | 			LL_I2C_EnableBitPOS(i2c); | 
 | 		} | 
 | 	} | 
 | } | 
 |  | 
 | static inline void handle_addr(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	if (I2C_ADDR_10_BITS & data->dev_config) { | 
 | 		if (!data->current.is_write && data->current.is_restart) { | 
 | 			data->current.is_restart = 0U; | 
 | 			LL_I2C_ClearFlag_ADDR(i2c); | 
 | 			stm32_i2c_generate_start_condition(i2c); | 
 |  | 
 | 			return; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (data->current.is_write) { | 
 | 		LL_I2C_ClearFlag_ADDR(i2c); | 
 | 		return; | 
 | 	} | 
 | 	/* according to STM32F1 errata we need to handle these corner cases in | 
 | 	 * specific way. | 
 | 	 * Please ref to STM32F10xxC/D/E I2C peripheral Errata sheet 2.14.1 | 
 | 	 */ | 
 | 	if (data->current.len == 0U && IS_ENABLED(CONFIG_SOC_SERIES_STM32F1X)) { | 
 | 		LL_I2C_GenerateStopCondition(i2c); | 
 | 	} else if (data->current.len == 1U) { | 
 | 		/* Single byte reception: enable NACK and clear POS */ | 
 | 		LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | #ifdef CONFIG_SOC_SERIES_STM32F1X | 
 | 		LL_I2C_ClearFlag_ADDR(i2c); | 
 | 		LL_I2C_GenerateStopCondition(i2c); | 
 | #endif | 
 | 	} else if (data->current.len == 2U) { | 
 | #ifdef CONFIG_SOC_SERIES_STM32F1X | 
 | 		LL_I2C_ClearFlag_ADDR(i2c); | 
 | #endif | 
 | 		/* 2-byte reception: enable NACK and set POS */ | 
 | 		LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 		LL_I2C_EnableBitPOS(i2c); | 
 | 	} | 
 | 	LL_I2C_ClearFlag_ADDR(i2c); | 
 | } | 
 |  | 
 | static inline void handle_txe(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	if (data->current.len) { | 
 | 		data->current.len--; | 
 | 		if (data->current.len == 0U) { | 
 | 			/* | 
 | 			 * This is the last byte to transmit disable Buffer | 
 | 			 * interrupt and wait for a BTF interrupt | 
 | 			 */ | 
 | 			LL_I2C_DisableIT_BUF(i2c); | 
 | 		} | 
 | 		LL_I2C_TransmitData8(i2c, *data->current.buf); | 
 | 		data->current.buf++; | 
 | 	} else { | 
 | 		if (data->current.flags & I2C_MSG_STOP) { | 
 | 			LL_I2C_GenerateStopCondition(i2c); | 
 | 		} | 
 | 		if (LL_I2C_IsActiveFlag_BTF(i2c)) { | 
 | 			/* Read DR to clear BTF flag */ | 
 | 			LL_I2C_ReceiveData8(i2c); | 
 | 		} | 
 |  | 
 | 		k_sem_give(&data->device_sync_sem); | 
 | 	} | 
 | } | 
 |  | 
 | static inline void handle_rxne(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	if (data->current.len > 0) { | 
 | 		switch (data->current.len) { | 
 | 		case 1: | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 			LL_I2C_DisableBitPOS(i2c); | 
 | 			/* Single byte reception */ | 
 | 			if (data->current.flags & I2C_MSG_STOP) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 			} | 
 | 			LL_I2C_DisableIT_BUF(i2c); | 
 | 			data->current.len--; | 
 | 			*data->current.buf = LL_I2C_ReceiveData8(i2c); | 
 | 			data->current.buf++; | 
 |  | 
 | 			k_sem_give(&data->device_sync_sem); | 
 | 			break; | 
 | 		case 2: | 
 | 			/* | 
 | 			 * 2-byte reception for N > 3 has already set the NACK | 
 | 			 * bit, and must not set the POS bit. See pg. 854 in | 
 | 			 * the F4 reference manual (RM0090). | 
 | 			 */ | 
 | 			if (data->current.msg->len > 2) { | 
 | 				break; | 
 | 			} | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 			LL_I2C_EnableBitPOS(i2c); | 
 | 			__fallthrough; | 
 | 		case 3: | 
 | 			/* | 
 | 			 * 2-byte, 3-byte reception and for N-2, N-1, | 
 | 			 * N when N > 3 | 
 | 			 */ | 
 | 			LL_I2C_DisableIT_BUF(i2c); | 
 | 			break; | 
 | 		default: | 
 | 			/* N byte reception when N > 3 */ | 
 | 			data->current.len--; | 
 | 			*data->current.buf = LL_I2C_ReceiveData8(i2c); | 
 | 			data->current.buf++; | 
 | 		} | 
 | 	} else { | 
 |  | 
 | 		if (data->current.flags & I2C_MSG_STOP) { | 
 | 			LL_I2C_GenerateStopCondition(i2c); | 
 | 		} | 
 | 		k_sem_give(&data->device_sync_sem); | 
 | 	} | 
 | } | 
 |  | 
 | static inline void handle_btf(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	if (data->current.is_write) { | 
 | 		handle_txe(dev); | 
 | 	} else { | 
 | 		uint32_t counter = 0U; | 
 |  | 
 | 		switch (data->current.len) { | 
 | 		case 2: | 
 | 			/* | 
 | 			 * Stop condition must be generated before reading the | 
 | 			 * last two bytes. | 
 | 			 */ | 
 | 			if (data->current.flags & I2C_MSG_STOP) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 			} | 
 |  | 
 | 			for (counter = 2U; counter > 0; counter--) { | 
 | 				data->current.len--; | 
 | 				*data->current.buf = LL_I2C_ReceiveData8(i2c); | 
 | 				data->current.buf++; | 
 | 			} | 
 | 			k_sem_give(&data->device_sync_sem); | 
 | 			break; | 
 | 		case 3: | 
 | 			/* Set NACK before reading N-2 byte*/ | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 			data->current.len--; | 
 | 			*data->current.buf = LL_I2C_ReceiveData8(i2c); | 
 | 			data->current.buf++; | 
 | 			break; | 
 | 		default: | 
 | 			handle_rxne(dev); | 
 | 		} | 
 | 	} | 
 | } | 
 |  | 
 |  | 
 | #if defined(CONFIG_I2C_TARGET) | 
 | static void stm32_i2c_slave_event(const struct device *dev) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 | 	const struct i2c_target_callbacks *slave_cb = | 
 | 		data->slave_cfg->callbacks; | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_TXE(i2c) && LL_I2C_IsActiveFlag_BTF(i2c)) { | 
 | 		uint8_t val; | 
 | 		slave_cb->read_processed(data->slave_cfg, &val); | 
 | 		LL_I2C_TransmitData8(i2c, val); | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_RXNE(i2c)) { | 
 | 		uint8_t val = LL_I2C_ReceiveData8(i2c); | 
 | 		if (slave_cb->write_received(data->slave_cfg, val)) { | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 		} | 
 | 		return; | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_AF(i2c)) { | 
 | 		LL_I2C_ClearFlag_AF(i2c); | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_STOP(i2c)) { | 
 | 		LL_I2C_ClearFlag_STOP(i2c); | 
 | 		slave_cb->stop(data->slave_cfg); | 
 | 		/* Prepare to ACK next transmissions address byte */ | 
 | 		LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_ADDR(i2c)) { | 
 | 		uint32_t dir = LL_I2C_GetTransferDirection(i2c); | 
 | 		if (dir == LL_I2C_DIRECTION_READ) { | 
 | 			slave_cb->write_requested(data->slave_cfg); | 
 | 			LL_I2C_EnableIT_RX(i2c); | 
 | 		} else { | 
 | 			uint8_t val; | 
 | 			slave_cb->read_requested(data->slave_cfg, &val); | 
 | 			LL_I2C_TransmitData8(i2c, val); | 
 | 			LL_I2C_EnableIT_TX(i2c); | 
 | 		} | 
 |  | 
 | 		stm32_i2c_enable_transfer_interrupts(dev); | 
 | 	} | 
 | } | 
 |  | 
 | /* Attach and start I2C as slave */ | 
 | int i2c_stm32_target_register(const struct device *dev, struct i2c_target_config *config) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 | 	uint32_t bitrate_cfg; | 
 | 	int ret; | 
 |  | 
 | 	if (!config) { | 
 | 		return -EINVAL; | 
 | 	} | 
 |  | 
 | 	if (data->slave_attached) { | 
 | 		return -EBUSY; | 
 | 	} | 
 |  | 
 | 	if (data->master_active) { | 
 | 		return -EBUSY; | 
 | 	} | 
 |  | 
 | 	bitrate_cfg = i2c_map_dt_bitrate(cfg->bitrate); | 
 |  | 
 | 	ret = i2c_stm32_runtime_configure(dev, bitrate_cfg); | 
 | 	if (ret < 0) { | 
 | 		LOG_ERR("i2c: failure initializing"); | 
 | 		return ret; | 
 | 	} | 
 |  | 
 | 	data->slave_cfg = config; | 
 |  | 
 | 	LL_I2C_Enable(i2c); | 
 |  | 
 | 	if (data->slave_cfg->flags == I2C_TARGET_FLAGS_ADDR_10_BITS)	{ | 
 | 		return -ENOTSUP; | 
 | 	} | 
 | 	LL_I2C_SetOwnAddress1(i2c, config->address << 1U, LL_I2C_OWNADDRESS1_7BIT); | 
 | 	data->slave_attached = true; | 
 |  | 
 | 	LOG_DBG("i2c: target registered"); | 
 |  | 
 | 	stm32_i2c_enable_transfer_interrupts(dev); | 
 | 	LL_I2C_AcknowledgeNextData(i2c, LL_I2C_ACK); | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | int i2c_stm32_target_unregister(const struct device *dev, struct i2c_target_config *config) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	if (!data->slave_attached) { | 
 | 		return -EINVAL; | 
 | 	} | 
 |  | 
 | 	if (data->master_active) { | 
 | 		return -EBUSY; | 
 | 	} | 
 |  | 
 | 	stm32_i2c_disable_transfer_interrupts(dev); | 
 |  | 
 | 	LL_I2C_ClearFlag_AF(i2c); | 
 | 	LL_I2C_ClearFlag_STOP(i2c); | 
 | 	LL_I2C_ClearFlag_ADDR(i2c); | 
 |  | 
 | 	if (!data->smbalert_active) { | 
 | 		LL_I2C_Disable(i2c); | 
 | 	} | 
 |  | 
 | 	data->slave_attached = false; | 
 |  | 
 | 	LOG_DBG("i2c: slave unregistered"); | 
 |  | 
 | 	return 0; | 
 | } | 
 | #endif /* defined(CONFIG_I2C_TARGET) */ | 
 |  | 
 | void stm32_i2c_event_isr(void *arg) | 
 | { | 
 | 	const struct device *dev = (const struct device *)arg; | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | #if defined(CONFIG_I2C_TARGET) | 
 | 	if (data->slave_attached && !data->master_active) { | 
 | 		stm32_i2c_slave_event(dev); | 
 | 		return; | 
 | 	} | 
 | #endif | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_SB(i2c)) { | 
 | 		handle_sb(dev); | 
 | 	} else if (LL_I2C_IsActiveFlag_ADD10(i2c)) { | 
 | 		LL_I2C_TransmitData8(i2c, data->slave_address); | 
 | 	} else if (LL_I2C_IsActiveFlag_ADDR(i2c)) { | 
 | 		handle_addr(dev); | 
 | 	} else if (LL_I2C_IsActiveFlag_BTF(i2c)) { | 
 | 		handle_btf(dev); | 
 | 	} else if (LL_I2C_IsActiveFlag_TXE(i2c) && data->current.is_write) { | 
 | 		handle_txe(dev); | 
 | 	} else if (LL_I2C_IsActiveFlag_RXNE(i2c) && !data->current.is_write) { | 
 | 		handle_rxne(dev); | 
 | 	} | 
 | } | 
 |  | 
 | void stm32_i2c_error_isr(void *arg) | 
 | { | 
 | 	const struct device *dev = (const struct device *)arg; | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | #if defined(CONFIG_I2C_TARGET) | 
 | 	if (data->slave_attached && !data->master_active) { | 
 | 		/* No need for a slave error function right now. */ | 
 | 		return; | 
 | 	} | 
 | #endif | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_AF(i2c)) { | 
 | 		LL_I2C_ClearFlag_AF(i2c); | 
 | 		LL_I2C_GenerateStopCondition(i2c); | 
 | 		data->current.is_nack = 1U; | 
 | 		goto end; | 
 | 	} | 
 | 	if (LL_I2C_IsActiveFlag_ARLO(i2c)) { | 
 | 		LL_I2C_ClearFlag_ARLO(i2c); | 
 | 		data->current.is_arlo = 1U; | 
 | 		goto end; | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_BERR(i2c)) { | 
 | 		LL_I2C_ClearFlag_BERR(i2c); | 
 | 		data->current.is_err = 1U; | 
 | 		goto end; | 
 | 	} | 
 |  | 
 | #if defined(CONFIG_SMBUS_STM32_SMBALERT) | 
 | 	if (LL_I2C_IsActiveSMBusFlag_ALERT(i2c)) { | 
 | 		LL_I2C_ClearSMBusFlag_ALERT(i2c); | 
 | 		if (data->smbalert_cb_func != NULL) { | 
 | 			data->smbalert_cb_func(data->smbalert_cb_dev); | 
 | 		} | 
 | 		goto end; | 
 | 	} | 
 | #endif | 
 | 	return; | 
 | end: | 
 | 	stm32_i2c_master_mode_end(dev); | 
 | } | 
 |  | 
 | static int32_t stm32_i2c_msg_write(const struct device *dev, struct i2c_msg *msg, | 
 | 			    uint8_t *next_msg_flags, uint16_t saddr) | 
 | { | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 |  | 
 | 	msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_WRITE); | 
 |  | 
 | 	stm32_i2c_enable_transfer_interrupts(dev); | 
 |  | 
 | 	if (k_sem_take(&data->device_sync_sem, | 
 | 			K_MSEC(STM32_I2C_TRANSFER_TIMEOUT_MSEC)) != 0) { | 
 | 		LOG_DBG("%s: WRITE timeout", __func__); | 
 | 		stm32_i2c_reset(dev); | 
 | 		return -EIO; | 
 | 	} | 
 |  | 
 | 	return msg_end(dev, next_msg_flags, __func__); | 
 | } | 
 |  | 
 | static int32_t stm32_i2c_msg_read(const struct device *dev, struct i2c_msg *msg, | 
 | 			   uint8_t *next_msg_flags, uint16_t saddr) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_READ); | 
 |  | 
 | 	stm32_i2c_enable_transfer_interrupts(dev); | 
 | 	LL_I2C_EnableIT_RX(i2c); | 
 |  | 
 | 	if (k_sem_take(&data->device_sync_sem, | 
 | 			K_MSEC(STM32_I2C_TRANSFER_TIMEOUT_MSEC)) != 0) { | 
 | 		LOG_DBG("%s: READ timeout", __func__); | 
 | 		stm32_i2c_reset(dev); | 
 | 		return -EIO; | 
 | 	} | 
 |  | 
 | 	return msg_end(dev, next_msg_flags, __func__); | 
 | } | 
 |  | 
 | #else /* CONFIG_I2C_STM32_INTERRUPT */ | 
 |  | 
 | static inline int check_errors(const struct device *dev, const char *funcname) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_AF(i2c)) { | 
 | 		LL_I2C_ClearFlag_AF(i2c); | 
 | 		LOG_DBG("%s: NACK", funcname); | 
 | 		data->current.is_nack = 1U; | 
 | 		goto error; | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_ARLO(i2c)) { | 
 | 		LL_I2C_ClearFlag_ARLO(i2c); | 
 | 		LOG_DBG("%s: ARLO", funcname); | 
 | 		data->current.is_arlo = 1U; | 
 | 		goto error; | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_OVR(i2c)) { | 
 | 		LL_I2C_ClearFlag_OVR(i2c); | 
 | 		LOG_DBG("%s: OVR", funcname); | 
 | 		data->current.is_err = 1U; | 
 | 		goto error; | 
 | 	} | 
 |  | 
 | 	if (LL_I2C_IsActiveFlag_BERR(i2c)) { | 
 | 		LL_I2C_ClearFlag_BERR(i2c); | 
 | 		LOG_DBG("%s: BERR", funcname); | 
 | 		data->current.is_err = 1U; | 
 | 		goto error; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | error: | 
 | 	return -EIO; | 
 | } | 
 |  | 
 | static int stm32_i2c_wait_timeout(uint16_t *timeout) | 
 | { | 
 | 	if (*timeout == 0) { | 
 | 		return 1; | 
 | 	} else { | 
 | 		k_busy_wait(1); | 
 | 		(*timeout)--; | 
 | 		return 0; | 
 | 	} | 
 | } | 
 |  | 
 | static int32_t stm32_i2c_msg_write(const struct device *dev, struct i2c_msg *msg, | 
 | 			    uint8_t *next_msg_flags, uint16_t saddr) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 | 	uint32_t len = msg->len; | 
 | 	uint16_t timeout; | 
 | 	uint8_t *buf = msg->buf; | 
 | 	int32_t res; | 
 |  | 
 | 	msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_WRITE); | 
 |  | 
 | 	if (msg->flags & I2C_MSG_RESTART) { | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		while (!LL_I2C_IsActiveFlag_SB(i2c)) { | 
 | 			if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 				data->current.is_err = 1U; | 
 | 				goto end; | 
 | 			} | 
 | 		} | 
 |  | 
 | 		if (I2C_ADDR_10_BITS & data->dev_config) { | 
 | 			uint8_t slave = (((saddr & 0x0300) >> 7) & 0xFF); | 
 | 			uint8_t header = slave | HEADER; | 
 |  | 
 | 			LL_I2C_TransmitData8(i2c, header); | 
 | 			timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 			while (!LL_I2C_IsActiveFlag_ADD10(i2c)) { | 
 | 				if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 					LL_I2C_GenerateStopCondition(i2c); | 
 | 					data->current.is_err = 1U; | 
 | 					goto end; | 
 | 				} | 
 | 			} | 
 |  | 
 | 			slave = data->slave_address & 0xFF; | 
 | 			LL_I2C_TransmitData8(i2c, slave); | 
 | 		} else { | 
 | 			uint8_t slave = (saddr << 1) & 0xFF; | 
 |  | 
 | 			LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_WRITE); | 
 | 		} | 
 |  | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		while (!LL_I2C_IsActiveFlag_ADDR(i2c)) { | 
 | 			if (LL_I2C_IsActiveFlag_AF(i2c) || stm32_i2c_wait_timeout(&timeout)) { | 
 | 				LL_I2C_ClearFlag_AF(i2c); | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 				data->current.is_nack = 1U; | 
 | 				goto end; | 
 | 			} | 
 | 		} | 
 | 		LL_I2C_ClearFlag_ADDR(i2c); | 
 | 	} | 
 |  | 
 | 	while (len) { | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		while (1) { | 
 | 			if (LL_I2C_IsActiveFlag_TXE(i2c)) { | 
 | 				break; | 
 | 			} | 
 | 			if (LL_I2C_IsActiveFlag_AF(i2c) || stm32_i2c_wait_timeout(&timeout)) { | 
 | 				LL_I2C_ClearFlag_AF(i2c); | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 				data->current.is_nack = 1U; | 
 | 				goto end; | 
 | 			} | 
 | 		} | 
 | 		LL_I2C_TransmitData8(i2c, *buf); | 
 | 		buf++; | 
 | 		len--; | 
 | 	} | 
 |  | 
 | 	timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 	while (!LL_I2C_IsActiveFlag_BTF(i2c)) { | 
 | 		if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 			LL_I2C_GenerateStopCondition(i2c); | 
 | 			data->current.is_err = 1U; | 
 | 			goto end; | 
 | 		} | 
 | 	} | 
 |  | 
 | 	if (msg->flags & I2C_MSG_STOP) { | 
 | 		LL_I2C_GenerateStopCondition(i2c); | 
 | 	} | 
 |  | 
 | end: | 
 | 	check_errors(dev, __func__); | 
 | 	res = msg_end(dev, next_msg_flags, __func__); | 
 | 	if (res < 0) { | 
 | 		stm32_i2c_reset(dev); | 
 | 	} | 
 |  | 
 | 	return res; | 
 | } | 
 |  | 
 | static int32_t stm32_i2c_msg_read(const struct device *dev, struct i2c_msg *msg, | 
 | 			   uint8_t *next_msg_flags, uint16_t saddr) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 | 	uint32_t len = msg->len; | 
 | 	uint16_t timeout; | 
 | 	uint8_t *buf = msg->buf; | 
 | 	int32_t res; | 
 |  | 
 | 	msg_init(dev, msg, next_msg_flags, saddr, I2C_REQUEST_READ); | 
 |  | 
 | 	if (msg->flags & I2C_MSG_RESTART) { | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		while (!LL_I2C_IsActiveFlag_SB(i2c)) { | 
 | 			if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 				data->current.is_err = 1U; | 
 | 				goto end; | 
 | 			} | 
 | 		} | 
 |  | 
 | 		if (I2C_ADDR_10_BITS & data->dev_config) { | 
 | 			uint8_t slave = (((saddr & 0x0300) >> 7) & 0xFF); | 
 | 			uint8_t header = slave | HEADER; | 
 |  | 
 | 			LL_I2C_TransmitData8(i2c, header); | 
 | 			timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 			while (!LL_I2C_IsActiveFlag_ADD10(i2c)) { | 
 | 				if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 					LL_I2C_GenerateStopCondition(i2c); | 
 | 					data->current.is_err = 1U; | 
 | 					goto end; | 
 | 				} | 
 | 			} | 
 |  | 
 | 			slave = saddr & 0xFF; | 
 | 			LL_I2C_TransmitData8(i2c, slave); | 
 | 			timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 			while (!LL_I2C_IsActiveFlag_ADDR(i2c)) { | 
 | 				if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 					LL_I2C_GenerateStopCondition(i2c); | 
 | 					data->current.is_err = 1U; | 
 | 					goto end; | 
 | 				} | 
 | 			} | 
 |  | 
 | 			LL_I2C_ClearFlag_ADDR(i2c); | 
 | 			stm32_i2c_generate_start_condition(i2c); | 
 | 			timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 			while (!LL_I2C_IsActiveFlag_SB(i2c)) { | 
 | 				if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 					LL_I2C_GenerateStopCondition(i2c); | 
 | 					data->current.is_err = 1U; | 
 | 					goto end; | 
 | 				} | 
 | 			} | 
 |  | 
 | 			header |= I2C_REQUEST_READ; | 
 | 			LL_I2C_TransmitData8(i2c, header); | 
 | 		} else { | 
 | 			uint8_t slave = ((saddr) << 1) & 0xFF; | 
 |  | 
 | 			LL_I2C_TransmitData8(i2c, slave | I2C_REQUEST_READ); | 
 | 		} | 
 |  | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		while (!LL_I2C_IsActiveFlag_ADDR(i2c)) { | 
 | 			if (LL_I2C_IsActiveFlag_AF(i2c) || stm32_i2c_wait_timeout(&timeout)) { | 
 | 				LL_I2C_ClearFlag_AF(i2c); | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 				data->current.is_nack = 1U; | 
 | 				goto end; | 
 | 			} | 
 | 		} | 
 | 		/* ADDR must be cleared before NACK generation. Either in 2 byte reception | 
 | 		 * byte 1 will be NACK'ed and slave won't sent the last byte | 
 | 		 */ | 
 | 		LL_I2C_ClearFlag_ADDR(i2c); | 
 | 		if (len == 1U) { | 
 | 			/* Single byte reception: enable NACK and set STOP */ | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 		} else if (len == 2U) { | 
 | 			/* 2-byte reception: enable NACK and set POS */ | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 			LL_I2C_EnableBitPOS(i2c); | 
 | 		} | 
 | 	} | 
 |  | 
 | 	while (len) { | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		while (!LL_I2C_IsActiveFlag_RXNE(i2c)) { | 
 | 			if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 				data->current.is_err = 1U; | 
 | 				goto end; | 
 | 			} | 
 | 		} | 
 |  | 
 | 		timeout = STM32_I2C_TIMEOUT_USEC; | 
 | 		switch (len) { | 
 | 		case 1: | 
 | 			if (msg->flags & I2C_MSG_STOP) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 			} | 
 | 			len--; | 
 | 			*buf = LL_I2C_ReceiveData8(i2c); | 
 | 			buf++; | 
 | 			break; | 
 | 		case 2: | 
 | 			while (!LL_I2C_IsActiveFlag_BTF(i2c)) { | 
 | 				if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 					LL_I2C_GenerateStopCondition(i2c); | 
 | 					data->current.is_err = 1U; | 
 | 					goto end; | 
 | 				} | 
 | 			} | 
 |  | 
 | 			/* | 
 | 			 * Stop condition must be generated before reading the | 
 | 			 * last two bytes. | 
 | 			 */ | 
 | 			if (msg->flags & I2C_MSG_STOP) { | 
 | 				LL_I2C_GenerateStopCondition(i2c); | 
 | 			} | 
 |  | 
 | 			for (uint32_t counter = 2; counter > 0; counter--) { | 
 | 				len--; | 
 | 				*buf = LL_I2C_ReceiveData8(i2c); | 
 | 				buf++; | 
 | 			} | 
 |  | 
 | 			break; | 
 | 		case 3: | 
 | 			while (!LL_I2C_IsActiveFlag_BTF(i2c)) { | 
 | 				if (stm32_i2c_wait_timeout(&timeout)) { | 
 | 					LL_I2C_GenerateStopCondition(i2c); | 
 | 					data->current.is_err = 1U; | 
 | 					goto end; | 
 | 				} | 
 | 			} | 
 |  | 
 | 			/* Set NACK before reading N-2 byte*/ | 
 | 			LL_I2C_AcknowledgeNextData(i2c, LL_I2C_NACK); | 
 | 			__fallthrough; | 
 | 		default: | 
 | 			len--; | 
 | 			*buf = LL_I2C_ReceiveData8(i2c); | 
 | 			buf++; | 
 | 		} | 
 | 	} | 
 | end: | 
 | 	check_errors(dev, __func__); | 
 | 	res = msg_end(dev, next_msg_flags, __func__); | 
 | 	if (res < 0) { | 
 | 		stm32_i2c_reset(dev); | 
 | 	} | 
 |  | 
 | 	return res; | 
 | } | 
 | #endif /* CONFIG_I2C_STM32_INTERRUPT */ | 
 |  | 
 | int stm32_i2c_configure_timing(const struct device *dev, uint32_t clock) | 
 | { | 
 | 	const struct i2c_stm32_config *cfg = dev->config; | 
 | 	struct i2c_stm32_data *data = dev->data; | 
 | 	I2C_TypeDef *i2c = cfg->i2c; | 
 |  | 
 | 	switch (I2C_SPEED_GET(data->dev_config)) { | 
 | 	case I2C_SPEED_STANDARD: | 
 | 		LL_I2C_ConfigSpeed(i2c, clock, 100000, LL_I2C_DUTYCYCLE_2); | 
 | 		break; | 
 | 	case I2C_SPEED_FAST: | 
 | 		LL_I2C_ConfigSpeed(i2c, clock, 400000, LL_I2C_DUTYCYCLE_2); | 
 | 		break; | 
 | 	default: | 
 | 		return -EINVAL; | 
 | 	} | 
 |  | 
 | 	return 0; | 
 | } | 
 |  | 
 | int stm32_i2c_transaction(const struct device *dev, | 
 | 						  struct i2c_msg msg, uint8_t *next_msg_flags, | 
 | 						  uint16_t periph) | 
 | { | 
 | 	int ret; | 
 |  | 
 | 	if ((msg.flags & I2C_MSG_RW_MASK) == I2C_MSG_WRITE) { | 
 | 		ret = stm32_i2c_msg_write(dev, &msg, next_msg_flags, periph); | 
 | 	} else { | 
 | 		ret = stm32_i2c_msg_read(dev, &msg, next_msg_flags, periph); | 
 | 	} | 
 | 	return ret; | 
 | } |