blob: 637e4c72260c1e50d71415d2318e6399eef3de4a [file] [log] [blame]
/* MCUX Ethernet Driver
*
* Copyright (c) 2016-2017 ARM Ltd
* Copyright (c) 2016 Linaro Ltd
* Copyright (c) 2018 Intel Corporation
* Copyright 2023 NXP
*
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT nxp_kinetis_ethernet
/* Driver Limitations:
*
* There is no statistics collection for either normal operation or
* error behaviour.
*/
#define LOG_MODULE_NAME eth_mcux
#define LOG_LEVEL CONFIG_ETHERNET_LOG_LEVEL
#define RING_ID 0
#include <zephyr/logging/log.h>
LOG_MODULE_REGISTER(LOG_MODULE_NAME);
#include <zephyr/device.h>
#include <zephyr/sys/util.h>
#include <zephyr/kernel.h>
#include <zephyr/sys/__assert.h>
#include <zephyr/net/net_pkt.h>
#include <zephyr/net/net_if.h>
#include <zephyr/net/ethernet.h>
#include <ethernet/eth_stats.h>
#include <zephyr/pm/device.h>
#include <zephyr/irq.h>
#if defined(CONFIG_PTP_CLOCK_MCUX)
#include <zephyr/drivers/ptp_clock.h>
#endif
#if defined(CONFIG_NET_DSA)
#include <zephyr/net/dsa.h>
#endif
#include "fsl_enet.h"
#include "fsl_phy.h"
#include "fsl_phyksz8081.h"
#include "fsl_enet_mdio.h"
#if defined(CONFIG_NET_POWER_MANAGEMENT)
#include "fsl_clock.h"
#include <zephyr/drivers/clock_control.h>
#endif
#include <zephyr/devicetree.h>
#include <zephyr/drivers/gpio.h>
#if defined(CONFIG_PINCTRL)
#include <zephyr/drivers/pinctrl.h>
#endif
#include "eth.h"
#define PHY_OMS_OVERRIDE_REG 0x16U /* The PHY Operation Mode Strap Override register. */
#define PHY_OMS_STATUS_REG 0x17U /* The PHY Operation Mode Strap Status register. */
#define PHY_OMS_NANDTREE_MASK 0x0020U /* The PHY NAND Tree Strap-In Override/Status mask. */
#define PHY_OMS_FACTORY_MODE_MASK 0x8000U /* The factory mode Override/Status mask. */
/* Defines the PHY KSZ8081 vendor defined registers. */
#define PHY_CONTROL1_REG 0x1EU /* The PHY control one register. */
#define PHY_CONTROL2_REG 0x1FU /* The PHY control two register. */
/* Defines the PHY KSZ8081 ID number. */
#define PHY_CONTROL_ID1 0x22U /* The PHY ID1 */
/* Defines the mask flag of operation mode in control registers */
#define PHY_CTL2_REMOTELOOP_MASK 0x0004U /* The PHY remote loopback mask. */
#define PHY_CTL2_REFCLK_SELECT_MASK 0x0080U /* The PHY RMII reference clock select. */
#define PHY_CTL1_10HALFDUPLEX_MASK 0x0001U /* The PHY 10M half duplex mask. */
#define PHY_CTL1_100HALFDUPLEX_MASK 0x0002U /* The PHY 100M half duplex mask. */
#define PHY_CTL1_10FULLDUPLEX_MASK 0x0005U /* The PHY 10M full duplex mask. */
#define PHY_CTL1_100FULLDUPLEX_MASK 0x0006U /* The PHY 100M full duplex mask. */
#define PHY_CTL1_SPEEDUPLX_MASK 0x0007U /* The PHY speed and duplex mask. */
#define PHY_CTL1_ENERGYDETECT_MASK 0x10U /* The PHY signal present on rx differential pair. */
#define PHY_CTL1_LINKUP_MASK 0x100U /* The PHY link up. */
#define PHY_LINK_READY_MASK (PHY_CTL1_ENERGYDETECT_MASK | PHY_CTL1_LINKUP_MASK)
/* Defines the timeout macro. */
#define PHY_READID_TIMEOUT_COUNT 1000U
/* Define RX and TX thread stack sizes */
#define ETH_MCUX_RX_THREAD_STACK_SIZE 1600
#define ETH_MCUX_TX_THREAD_STACK_SIZE 1600
#define FREESCALE_OUI_B0 0x00
#define FREESCALE_OUI_B1 0x04
#define FREESCALE_OUI_B2 0x9f
#define ETH_MCUX_FIXED_LINK_NODE \
DT_CHILD(DT_NODELABEL(enet), fixed_link)
#define ETH_MCUX_FIXED_LINK \
DT_NODE_EXISTS(ETH_MCUX_FIXED_LINK_NODE)
#define ETH_MCUX_FIXED_LINK_SPEED \
DT_PROP(ETH_MCUX_FIXED_LINK_NODE, speed)
#define ETH_MCUX_FIXED_LINK_FULL_DUPLEX \
DT_PROP(ETH_MCUX_FIXED_LINK_NODE, full_duplex)
enum eth_mcux_phy_state {
eth_mcux_phy_state_initial,
eth_mcux_phy_state_reset,
eth_mcux_phy_state_autoneg,
eth_mcux_phy_state_restart,
eth_mcux_phy_state_read_status,
eth_mcux_phy_state_read_duplex,
eth_mcux_phy_state_wait,
eth_mcux_phy_state_closing
};
struct _phy_resource {
mdioWrite write;
mdioRead read;
};
#if defined(CONFIG_NET_POWER_MANAGEMENT)
extern uint32_t ENET_GetInstance(ENET_Type * base);
static const clock_ip_name_t enet_clocks[] = ENET_CLOCKS;
#endif
static void eth_mcux_init(const struct device *dev);
#if defined(CONFIG_ETH_MCUX_PHY_EXTRA_DEBUG)
static const char *phy_state_name(enum eth_mcux_phy_state state)
{
static const char * const name[] = {
"initial",
"reset",
"autoneg",
"restart",
"read-status",
"read-duplex",
"wait",
"closing"
};
return name[state];
}
#endif
static const char *eth_name(ENET_Type *base)
{
switch ((int)base) {
case DT_INST_REG_ADDR(0):
return "ETH_0";
#if DT_NODE_HAS_STATUS(DT_DRV_INST(1), okay)
case DT_INST_REG_ADDR(1):
return "ETH_1";
#endif
default:
return "unknown";
}
}
struct eth_context {
ENET_Type *base;
void (*config_func)(void);
/* If VLAN is enabled, there can be multiple VLAN interfaces related to
* this physical device. In that case, this pointer value is not really
* used for anything.
*/
struct net_if *iface;
#if defined(CONFIG_NET_POWER_MANAGEMENT)
clock_ip_name_t clock;
const struct device *clock_dev;
#endif
enet_handle_t enet_handle;
#if defined(CONFIG_PTP_CLOCK_MCUX)
const struct device *ptp_clock;
enet_ptp_config_t ptp_config;
double clk_ratio;
struct k_mutex ptp_mutex;
struct k_sem ptp_ts_sem;
#endif
struct k_sem tx_buf_sem;
phy_handle_t *phy_handle;
struct _phy_resource *phy_config;
struct k_sem rx_thread_sem;
enum eth_mcux_phy_state phy_state;
bool enabled;
bool link_up;
uint32_t phy_addr;
uint32_t rx_irq_num;
uint32_t tx_irq_num;
phy_duplex_t phy_duplex;
phy_speed_t phy_speed;
uint8_t mac_addr[6];
void (*generate_mac)(uint8_t *);
struct k_work phy_work;
struct k_work_delayable delayed_phy_work;
K_KERNEL_STACK_MEMBER(rx_thread_stack, ETH_MCUX_RX_THREAD_STACK_SIZE);
struct k_thread rx_thread;
/* TODO: FIXME. This Ethernet frame sized buffer is used for
* interfacing with MCUX. How it works is that hardware uses
* DMA scatter buffers to receive a frame, and then public
* MCUX call gathers them into this buffer (there's no other
* public interface). All this happens only for this driver
* to scatter this buffer again into Zephyr fragment buffers.
* This is not efficient, but proper resolution of this issue
* depends on introduction of zero-copy networking support
* in Zephyr, and adding needed interface to MCUX (or
* bypassing it and writing a more complex driver working
* directly with hardware).
*
* Note that we do not copy FCS into this buffer thus the
* size is 1514 bytes.
*/
struct k_mutex tx_frame_buf_mutex;
struct k_mutex rx_frame_buf_mutex;
uint8_t *tx_frame_buf; /* Max MTU + ethernet header */
uint8_t *rx_frame_buf; /* Max MTU + ethernet header */
#if defined(CONFIG_PINCTRL)
const struct pinctrl_dev_config *pincfg;
#endif
#if defined(CONFIG_ETH_MCUX_PHY_RESET)
const struct gpio_dt_spec int_gpio;
const struct gpio_dt_spec reset_gpio;
#endif
};
/* Use ENET_FRAME_MAX_VLANFRAMELEN for VLAN frame size
* Use ENET_FRAME_MAX_FRAMELEN for Ethernet frame size
*/
#if defined(CONFIG_NET_VLAN)
#if !defined(ENET_FRAME_MAX_VLANFRAMELEN)
#define ENET_FRAME_MAX_VLANFRAMELEN (ENET_FRAME_MAX_FRAMELEN + 4)
#endif
#define ETH_MCUX_BUFFER_SIZE \
ROUND_UP(ENET_FRAME_MAX_VLANFRAMELEN, ENET_BUFF_ALIGNMENT)
#else
#define ETH_MCUX_BUFFER_SIZE \
ROUND_UP(ENET_FRAME_MAX_FRAMELEN, ENET_BUFF_ALIGNMENT)
#endif /* CONFIG_NET_VLAN */
#if defined(CONFIG_NET_POWER_MANAGEMENT)
static void eth_mcux_phy_enter_reset(struct eth_context *context);
void eth_mcux_phy_stop(struct eth_context *context);
static int eth_mcux_device_pm_action(const struct device *dev,
enum pm_device_action action)
{
struct eth_context *eth_ctx = dev->data;
int ret = 0;
if (!device_is_ready(eth_ctx->clock_dev)) {
LOG_ERR("No CLOCK dev");
ret = -EIO;
goto out;
}
switch (action) {
case PM_DEVICE_ACTION_SUSPEND:
LOG_DBG("Suspending");
ret = net_if_suspend(eth_ctx->iface);
if (ret == -EBUSY) {
goto out;
}
eth_mcux_phy_enter_reset(eth_ctx);
eth_mcux_phy_stop(eth_ctx);
ENET_Reset(eth_ctx->base);
ENET_Deinit(eth_ctx->base);
clock_control_off(eth_ctx->clock_dev,
(clock_control_subsys_t)eth_ctx->clock);
break;
case PM_DEVICE_ACTION_RESUME:
LOG_DBG("Resuming");
clock_control_on(eth_ctx->clock_dev,
(clock_control_subsys_t)eth_ctx->clock);
eth_mcux_init(dev);
net_if_resume(eth_ctx->iface);
break;
default:
ret = -ENOTSUP;
break;
}
out:
return ret;
}
#endif /* CONFIG_NET_POWER_MANAGEMENT */
#if ETH_MCUX_FIXED_LINK
static void eth_mcux_get_phy_params(phy_duplex_t *p_phy_duplex,
phy_speed_t *p_phy_speed)
{
*p_phy_duplex = kPHY_HalfDuplex;
#if ETH_MCUX_FIXED_LINK_FULL_DUPLEX
*p_phy_duplex = kPHY_FullDuplex;
#endif
*p_phy_speed = kPHY_Speed10M;
#if ETH_MCUX_FIXED_LINK_SPEED == 100
*p_phy_speed = kPHY_Speed100M;
#endif
}
#else
static void eth_mcux_decode_duplex_and_speed(uint32_t status,
phy_duplex_t *p_phy_duplex,
phy_speed_t *p_phy_speed)
{
switch (status & PHY_CTL1_SPEEDUPLX_MASK) {
case PHY_CTL1_10FULLDUPLEX_MASK:
*p_phy_duplex = kPHY_FullDuplex;
*p_phy_speed = kPHY_Speed10M;
break;
case PHY_CTL1_100FULLDUPLEX_MASK:
*p_phy_duplex = kPHY_FullDuplex;
*p_phy_speed = kPHY_Speed100M;
break;
case PHY_CTL1_100HALFDUPLEX_MASK:
*p_phy_duplex = kPHY_HalfDuplex;
*p_phy_speed = kPHY_Speed100M;
break;
case PHY_CTL1_10HALFDUPLEX_MASK:
*p_phy_duplex = kPHY_HalfDuplex;
*p_phy_speed = kPHY_Speed10M;
break;
}
}
#endif /* ETH_MCUX_FIXED_LINK */
static inline struct net_if *get_iface(struct eth_context *ctx, uint16_t vlan_tag)
{
#if defined(CONFIG_NET_VLAN)
struct net_if *iface;
iface = net_eth_get_vlan_iface(ctx->iface, vlan_tag);
if (!iface) {
return ctx->iface;
}
return iface;
#else
ARG_UNUSED(vlan_tag);
return ctx->iface;
#endif
}
static void eth_mcux_phy_enter_reset(struct eth_context *context)
{
/* Reset the PHY. */
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
ENET_StartSMIWrite(context->base, context->phy_addr,
PHY_BASICCONTROL_REG,
kENET_MiiWriteValidFrame,
PHY_BCTL_RESET_MASK);
#endif
context->phy_state = eth_mcux_phy_state_reset;
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
k_work_submit(&context->phy_work);
#endif
}
static void eth_mcux_phy_start(struct eth_context *context)
{
#if defined(CONFIG_ETH_MCUX_PHY_EXTRA_DEBUG)
LOG_DBG("%s phy_state=%s", eth_name(context->base),
phy_state_name(context->phy_state));
#endif
context->enabled = true;
switch (context->phy_state) {
case eth_mcux_phy_state_initial:
context->phy_handle->phyAddr = context->phy_addr;
ENET_ActiveRead(context->base);
/* Reset the PHY. */
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
ENET_StartSMIWrite(context->base, context->phy_addr,
PHY_BASICCONTROL_REG,
kENET_MiiWriteValidFrame,
PHY_BCTL_RESET_MASK);
#else
/*
* With no SMI communication one needs to wait for
* iface being up by the network core.
*/
k_work_submit(&context->phy_work);
break;
#endif
#if defined(CONFIG_SOC_SERIES_IMX_RT)
context->phy_state = eth_mcux_phy_state_initial;
#else
context->phy_state = eth_mcux_phy_state_reset;
#endif
break;
case eth_mcux_phy_state_reset:
eth_mcux_phy_enter_reset(context);
break;
case eth_mcux_phy_state_autoneg:
case eth_mcux_phy_state_restart:
case eth_mcux_phy_state_read_status:
case eth_mcux_phy_state_read_duplex:
case eth_mcux_phy_state_wait:
case eth_mcux_phy_state_closing:
break;
}
}
void eth_mcux_phy_stop(struct eth_context *context)
{
#if defined(CONFIG_ETH_MCUX_PHY_EXTRA_DEBUG)
LOG_DBG("%s phy_state=%s", eth_name(context->base),
phy_state_name(context->phy_state));
#endif
context->enabled = false;
switch (context->phy_state) {
case eth_mcux_phy_state_initial:
case eth_mcux_phy_state_reset:
case eth_mcux_phy_state_autoneg:
case eth_mcux_phy_state_restart:
case eth_mcux_phy_state_read_status:
case eth_mcux_phy_state_read_duplex:
/* Do nothing, let the current communication complete
* then deal with shutdown.
*/
context->phy_state = eth_mcux_phy_state_closing;
break;
case eth_mcux_phy_state_wait:
k_work_cancel_delayable(&context->delayed_phy_work);
/* @todo, actually power down the PHY ? */
context->phy_state = eth_mcux_phy_state_initial;
break;
case eth_mcux_phy_state_closing:
/* We are already going down. */
break;
}
}
static void eth_mcux_phy_event(struct eth_context *context)
{
#if !(defined(CONFIG_ETH_MCUX_NO_PHY_SMI) && ETH_MCUX_FIXED_LINK)
uint32_t status;
#endif
bool link_up;
#if defined(CONFIG_SOC_SERIES_IMX_RT)
status_t res;
uint16_t ctrl2;
#endif
phy_duplex_t phy_duplex = kPHY_FullDuplex;
phy_speed_t phy_speed = kPHY_Speed100M;
#if defined(CONFIG_ETH_MCUX_PHY_EXTRA_DEBUG)
LOG_DBG("%s phy_state=%s", eth_name(context->base),
phy_state_name(context->phy_state));
#endif
switch (context->phy_state) {
case eth_mcux_phy_state_initial:
#if defined(CONFIG_SOC_SERIES_IMX_RT)
ENET_DisableInterrupts(context->base, ENET_EIR_MII_MASK);
res = PHY_Read(context->phy_handle, PHY_CONTROL2_REG, &ctrl2);
ENET_EnableInterrupts(context->base, ENET_EIR_MII_MASK);
if (res != kStatus_Success) {
LOG_WRN("Reading PHY reg failed (status 0x%x)", res);
k_work_submit(&context->phy_work);
} else {
ctrl2 |= PHY_CTL2_REFCLK_SELECT_MASK;
ENET_StartSMIWrite(context->base, context->phy_addr,
PHY_CONTROL2_REG,
kENET_MiiWriteValidFrame,
ctrl2);
}
context->phy_state = eth_mcux_phy_state_reset;
#endif /* CONFIG_SOC_SERIES_IMX_RT */
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
/*
* When the iface is available proceed with the eth link setup,
* otherwise reschedule the eth_mcux_phy_event and check after
* 1ms
*/
if (context->iface) {
context->phy_state = eth_mcux_phy_state_reset;
}
k_work_reschedule(&context->delayed_phy_work, K_MSEC(1));
#endif
break;
case eth_mcux_phy_state_closing:
if (context->enabled) {
eth_mcux_phy_enter_reset(context);
} else {
/* @todo, actually power down the PHY ? */
context->phy_state = eth_mcux_phy_state_initial;
}
break;
case eth_mcux_phy_state_reset:
/* Setup PHY autonegotiation. */
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
ENET_StartSMIWrite(context->base, context->phy_addr,
PHY_AUTONEG_ADVERTISE_REG,
kENET_MiiWriteValidFrame,
(PHY_100BASETX_FULLDUPLEX_MASK |
PHY_100BASETX_HALFDUPLEX_MASK |
PHY_10BASETX_FULLDUPLEX_MASK |
PHY_10BASETX_HALFDUPLEX_MASK |
PHY_IEEE802_3_SELECTOR_MASK));
#endif
context->phy_state = eth_mcux_phy_state_autoneg;
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
k_work_submit(&context->phy_work);
#endif
break;
case eth_mcux_phy_state_autoneg:
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
/* Setup PHY autonegotiation. */
ENET_StartSMIWrite(context->base, context->phy_addr,
PHY_BASICCONTROL_REG,
kENET_MiiWriteValidFrame,
(PHY_BCTL_AUTONEG_MASK |
PHY_BCTL_RESTART_AUTONEG_MASK));
#endif
context->phy_state = eth_mcux_phy_state_restart;
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
k_work_submit(&context->phy_work);
#endif
break;
case eth_mcux_phy_state_wait:
case eth_mcux_phy_state_restart:
/* Start reading the PHY basic status. */
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
ENET_StartSMIRead(context->base, context->phy_addr,
PHY_BASICSTATUS_REG,
kENET_MiiReadValidFrame);
#endif
context->phy_state = eth_mcux_phy_state_read_status;
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
k_work_submit(&context->phy_work);
#endif
break;
case eth_mcux_phy_state_read_status:
/* PHY Basic status is available. */
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI) && ETH_MCUX_FIXED_LINK
link_up = true;
#else
status = ENET_ReadSMIData(context->base);
link_up = status & PHY_BSTATUS_LINKSTATUS_MASK;
#endif
if (link_up && !context->link_up && context->iface != NULL) {
/* Start reading the PHY control register. */
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
ENET_StartSMIRead(context->base, context->phy_addr,
PHY_CONTROL1_REG,
kENET_MiiReadValidFrame);
#endif
context->link_up = link_up;
context->phy_state = eth_mcux_phy_state_read_duplex;
net_eth_carrier_on(context->iface);
k_msleep(1);
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
k_work_submit(&context->phy_work);
#endif
} else if (!link_up && context->link_up && context->iface != NULL) {
LOG_INF("%s link down", eth_name(context->base));
context->link_up = link_up;
k_work_reschedule(&context->delayed_phy_work,
K_MSEC(CONFIG_ETH_MCUX_PHY_TICK_MS));
context->phy_state = eth_mcux_phy_state_wait;
net_eth_carrier_off(context->iface);
} else {
k_work_reschedule(&context->delayed_phy_work,
K_MSEC(CONFIG_ETH_MCUX_PHY_TICK_MS));
context->phy_state = eth_mcux_phy_state_wait;
}
break;
case eth_mcux_phy_state_read_duplex:
/* PHY control register is available. */
#if defined(CONFIG_ETH_MCUX_NO_PHY_SMI) && ETH_MCUX_FIXED_LINK
eth_mcux_get_phy_params(&phy_duplex, &phy_speed);
LOG_INF("%s - Fixed Link", eth_name(context->base));
#else
status = ENET_ReadSMIData(context->base);
eth_mcux_decode_duplex_and_speed(status,
&phy_duplex,
&phy_speed);
#endif
if (phy_speed != context->phy_speed ||
phy_duplex != context->phy_duplex) {
context->phy_speed = phy_speed;
context->phy_duplex = phy_duplex;
ENET_SetMII(context->base,
(enet_mii_speed_t) phy_speed,
(enet_mii_duplex_t) phy_duplex);
}
LOG_INF("%s enabled %sM %s-duplex mode.",
eth_name(context->base),
(phy_speed ? "100" : "10"),
(phy_duplex ? "full" : "half"));
k_work_reschedule(&context->delayed_phy_work,
K_MSEC(CONFIG_ETH_MCUX_PHY_TICK_MS));
context->phy_state = eth_mcux_phy_state_wait;
break;
}
}
static void eth_mcux_phy_work(struct k_work *item)
{
struct eth_context *context =
CONTAINER_OF(item, struct eth_context, phy_work);
eth_mcux_phy_event(context);
}
static void eth_mcux_delayed_phy_work(struct k_work *item)
{
struct eth_context *context =
CONTAINER_OF(item, struct eth_context, delayed_phy_work);
eth_mcux_phy_event(context);
}
static void eth_mcux_phy_setup(struct eth_context *context)
{
#if defined(CONFIG_SOC_SERIES_IMX_RT)
status_t res;
uint16_t oms_override;
/* Disable MII interrupts to prevent triggering PHY events. */
ENET_DisableInterrupts(context->base, ENET_EIR_MII_MASK);
res = PHY_Read(context->phy_handle,
PHY_OMS_OVERRIDE_REG, &oms_override);
if (res != kStatus_Success) {
LOG_WRN("Reading PHY reg failed (status 0x%x)", res);
} else {
/* Based on strap-in pins the PHY can be in factory test mode.
* Force normal operation.
*/
oms_override &= ~PHY_OMS_FACTORY_MODE_MASK;
/* Prevent PHY entering NAND Tree mode override. */
if (oms_override & PHY_OMS_NANDTREE_MASK) {
oms_override &= ~PHY_OMS_NANDTREE_MASK;
}
res = PHY_Write(context->phy_handle,
PHY_OMS_OVERRIDE_REG, oms_override);
if (res != kStatus_Success) {
LOG_WRN("Writing PHY reg failed (status 0x%x)", res);
}
}
ENET_EnableInterrupts(context->base, ENET_EIR_MII_MASK);
#endif
}
#if defined(CONFIG_PTP_CLOCK_MCUX)
static bool eth_get_ptp_data(struct net_if *iface, struct net_pkt *pkt)
{
int eth_hlen;
#if defined(CONFIG_NET_VLAN)
struct net_eth_vlan_hdr *hdr_vlan;
struct ethernet_context *eth_ctx;
bool vlan_enabled = false;
eth_ctx = net_if_l2_data(iface);
if (net_eth_is_vlan_enabled(eth_ctx, iface)) {
hdr_vlan = (struct net_eth_vlan_hdr *)NET_ETH_HDR(pkt);
vlan_enabled = true;
if (ntohs(hdr_vlan->type) != NET_ETH_PTYPE_PTP) {
return false;
}
eth_hlen = sizeof(struct net_eth_vlan_hdr);
} else
#endif
{
if (ntohs(NET_ETH_HDR(pkt)->type) != NET_ETH_PTYPE_PTP) {
return false;
}
eth_hlen = sizeof(struct net_eth_hdr);
}
net_pkt_set_priority(pkt, NET_PRIORITY_CA);
return true;
}
#endif /* CONFIG_PTP_CLOCK_MCUX */
static int eth_tx(const struct device *dev, struct net_pkt *pkt)
{
struct eth_context *context = dev->data;
uint16_t total_len = net_pkt_get_len(pkt);
status_t status;
#if defined(CONFIG_PTP_CLOCK_MCUX)
bool timestamped_frame;
#endif
/* Wait for a TX buffer descriptor to be available */
k_sem_take(&context->tx_buf_sem, K_FOREVER);
k_mutex_lock(&context->tx_frame_buf_mutex, K_FOREVER);
if (net_pkt_read(pkt, context->tx_frame_buf, total_len)) {
k_mutex_unlock(&context->tx_frame_buf_mutex);
return -EIO;
}
#if defined(CONFIG_PTP_CLOCK_MCUX)
timestamped_frame = eth_get_ptp_data(net_pkt_iface(pkt), pkt);
if (timestamped_frame) {
status = ENET_SendFrame(context->base, &context->enet_handle,
context->tx_frame_buf, total_len, RING_ID, true, pkt);
if (!status) {
net_pkt_ref(pkt);
/*
* Network stack will modify the packet upon return,
* so wait for the packet to be timestamped,
* which will occur within the TX ISR, before
* returning
*/
k_sem_take(&context->ptp_ts_sem, K_FOREVER);
}
} else
#endif
{
status = ENET_SendFrame(context->base, &context->enet_handle,
context->tx_frame_buf, total_len, RING_ID, false, NULL);
}
if (status) {
LOG_ERR("ENET_SendFrame error: %d", (int)status);
k_mutex_unlock(&context->tx_frame_buf_mutex);
ENET_ReclaimTxDescriptor(context->base,
&context->enet_handle, RING_ID);
return -1;
}
k_mutex_unlock(&context->tx_frame_buf_mutex);
return 0;
}
static int eth_rx(struct eth_context *context)
{
uint16_t vlan_tag = NET_VLAN_TAG_UNSPEC;
uint32_t frame_length = 0U;
struct net_if *iface;
struct net_pkt *pkt;
status_t status;
uint32_t ts;
#if defined(CONFIG_PTP_CLOCK_MCUX)
enet_ptp_time_t ptpTimeData;
#endif
status = ENET_GetRxFrameSize(&context->enet_handle,
(uint32_t *)&frame_length, RING_ID);
if (status == kStatus_ENET_RxFrameEmpty) {
return 0;
} else if (status == kStatus_ENET_RxFrameError) {
enet_data_error_stats_t error_stats;
LOG_ERR("ENET_GetRxFrameSize return: %d", (int)status);
ENET_GetRxErrBeforeReadFrame(&context->enet_handle,
&error_stats, RING_ID);
goto flush;
}
if (frame_length > NET_ETH_MAX_FRAME_SIZE) {
LOG_ERR("frame too large (%d)", frame_length);
goto flush;
}
/* Using root iface. It will be updated in net_recv_data() */
pkt = net_pkt_rx_alloc_with_buffer(context->iface, frame_length,
AF_UNSPEC, 0, K_NO_WAIT);
if (!pkt) {
goto flush;
}
/* in case multiply thread access
* we need to protect it with mutex.
*/
k_mutex_lock(&context->rx_frame_buf_mutex, K_FOREVER);
status = ENET_ReadFrame(context->base, &context->enet_handle,
context->rx_frame_buf, frame_length, RING_ID, &ts);
if (status) {
LOG_ERR("ENET_ReadFrame failed: %d", (int)status);
net_pkt_unref(pkt);
k_mutex_unlock(&context->rx_frame_buf_mutex);
goto error;
}
if (net_pkt_write(pkt, context->rx_frame_buf, frame_length)) {
LOG_ERR("Unable to write frame into the pkt");
net_pkt_unref(pkt);
k_mutex_unlock(&context->rx_frame_buf_mutex);
goto error;
}
k_mutex_unlock(&context->rx_frame_buf_mutex);
#if defined(CONFIG_NET_VLAN)
{
struct net_eth_hdr *hdr = NET_ETH_HDR(pkt);
if (ntohs(hdr->type) == NET_ETH_PTYPE_VLAN) {
struct net_eth_vlan_hdr *hdr_vlan =
(struct net_eth_vlan_hdr *)NET_ETH_HDR(pkt);
net_pkt_set_vlan_tci(pkt, ntohs(hdr_vlan->vlan.tci));
vlan_tag = net_pkt_vlan_tag(pkt);
#if CONFIG_NET_TC_RX_COUNT > 1
{
enum net_priority prio;
prio = net_vlan2priority(
net_pkt_vlan_priority(pkt));
net_pkt_set_priority(pkt, prio);
}
#endif
}
}
#endif /* CONFIG_NET_VLAN */
/*
* Use MAC timestamp
*/
#if defined(CONFIG_PTP_CLOCK_MCUX)
k_mutex_lock(&context->ptp_mutex, K_FOREVER);
if (eth_get_ptp_data(get_iface(context, vlan_tag), pkt)) {
ENET_Ptp1588GetTimer(context->base, &context->enet_handle,
&ptpTimeData);
/* If latest timestamp reloads after getting from Rx BD,
* then second - 1 to make sure the actual Rx timestamp is
* accurate
*/
if (ptpTimeData.nanosecond < ts) {
ptpTimeData.second--;
}
pkt->timestamp.nanosecond = ptpTimeData.nanosecond;
pkt->timestamp.second = ptpTimeData.second;
} else {
/* Invalid value. */
pkt->timestamp.nanosecond = UINT32_MAX;
pkt->timestamp.second = UINT64_MAX;
}
k_mutex_unlock(&context->ptp_mutex);
#endif /* CONFIG_PTP_CLOCK_MCUX */
iface = get_iface(context, vlan_tag);
#if defined(CONFIG_NET_DSA)
iface = dsa_net_recv(iface, &pkt);
#endif
if (net_recv_data(iface, pkt) < 0) {
net_pkt_unref(pkt);
goto error;
}
return 1;
flush:
/* Flush the current read buffer. This operation can
* only report failure if there is no frame to flush,
* which cannot happen in this context.
*/
status = ENET_ReadFrame(context->base, &context->enet_handle, NULL,
0, RING_ID, NULL);
__ASSERT_NO_MSG(status == kStatus_Success);
error:
eth_stats_update_errors_rx(get_iface(context, vlan_tag));
return -EIO;
}
#if defined(CONFIG_PTP_CLOCK_MCUX) && defined(CONFIG_NET_L2_PTP)
static inline void ts_register_tx_event(struct eth_context *context,
enet_frame_info_t *frameinfo)
{
struct net_pkt *pkt;
pkt = frameinfo->context;
if (pkt && atomic_get(&pkt->atomic_ref) > 0) {
if (eth_get_ptp_data(net_pkt_iface(pkt), pkt)) {
if (frameinfo->isTsAvail) {
k_mutex_lock(&context->ptp_mutex, K_FOREVER);
pkt->timestamp.nanosecond =
frameinfo->timeStamp.nanosecond;
pkt->timestamp.second =
frameinfo->timeStamp.second;
net_if_add_tx_timestamp(pkt);
k_sem_give(&context->ptp_ts_sem);
k_mutex_unlock(&context->ptp_mutex);
}
}
net_pkt_unref(pkt);
} else {
if (IS_ENABLED(CONFIG_ETH_MCUX_PHY_EXTRA_DEBUG) && pkt) {
LOG_ERR("pkt %p already freed", pkt);
}
}
}
#endif /* CONFIG_PTP_CLOCK_MCUX && CONFIG_NET_L2_PTP */
static void eth_callback(ENET_Type *base, enet_handle_t *handle,
#if FSL_FEATURE_ENET_QUEUE > 1
uint32_t ringId,
#endif /* FSL_FEATURE_ENET_QUEUE > 1 */
enet_event_t event, enet_frame_info_t *frameinfo, void *param)
{
struct eth_context *context = param;
switch (event) {
case kENET_RxEvent:
k_sem_give(&context->rx_thread_sem);
break;
case kENET_TxEvent:
#if defined(CONFIG_PTP_CLOCK_MCUX) && defined(CONFIG_NET_L2_PTP)
/* Register event */
ts_register_tx_event(context, frameinfo);
#endif /* CONFIG_PTP_CLOCK_MCUX && CONFIG_NET_L2_PTP */
/* Free the TX buffer. */
k_sem_give(&context->tx_buf_sem);
break;
case kENET_ErrEvent:
/* Error event: BABR/BABT/EBERR/LC/RL/UN/PLR. */
break;
case kENET_WakeUpEvent:
/* Wake up from sleep mode event. */
break;
case kENET_TimeStampEvent:
/* Time stamp event. */
/* Reset periodic timer to default value. */
context->base->ATPER = NSEC_PER_SEC;
break;
case kENET_TimeStampAvailEvent:
/* Time stamp available event. */
break;
}
}
static void eth_rx_thread(void *arg1, void *unused1, void *unused2)
{
struct eth_context *context = (struct eth_context *)arg1;
while (1) {
if (k_sem_take(&context->rx_thread_sem, K_FOREVER) == 0) {
while (eth_rx(context) == 1) {
;
}
/* enable the IRQ for RX */
ENET_EnableInterrupts(context->base,
kENET_RxFrameInterrupt | kENET_RxBufferInterrupt);
}
}
}
#if defined(CONFIG_ETH_MCUX_PHY_RESET)
static int eth_phy_reset(const struct device *dev)
{
int err;
struct eth_context *context = dev->data;
/* pull up the ENET_INT before RESET. */
err = gpio_pin_configure_dt(&context->int_gpio, GPIO_OUTPUT_ACTIVE);
if (err) {
return err;
}
return gpio_pin_configure_dt(&context->reset_gpio, GPIO_OUTPUT_INACTIVE);
}
static int eth_phy_init(const struct device *dev)
{
struct eth_context *context = dev->data;
/* RESET PHY chip. */
k_busy_wait(USEC_PER_MSEC * 500);
return gpio_pin_set_dt(&context->reset_gpio, 1);
}
#endif
static void eth_mcux_init(const struct device *dev)
{
struct eth_context *context = dev->data;
const enet_buffer_config_t *buffer_config = dev->config;
enet_config_t enet_config;
uint32_t sys_clock;
#if defined(CONFIG_PTP_CLOCK_MCUX)
uint8_t ptp_multicast[6] = { 0x01, 0x1B, 0x19, 0x00, 0x00, 0x00 };
uint8_t ptp_peer_multicast[6] = { 0x01, 0x80, 0xC2, 0x00, 0x00, 0x0E };
#endif
#if defined(CONFIG_MDNS_RESPONDER) || defined(CONFIG_MDNS_RESOLVER)
/* standard multicast MAC address */
uint8_t mdns_multicast[6] = { 0x01, 0x00, 0x5E, 0x00, 0x00, 0xFB };
#endif
context->phy_state = eth_mcux_phy_state_initial;
context->phy_handle->ops = &phyksz8081_ops;
#if defined(CONFIG_SOC_SERIES_IMX_RT10XX)
#if DT_NODE_HAS_STATUS(DT_NODELABEL(enet), okay)
sys_clock = CLOCK_GetFreq(kCLOCK_IpgClk);
#endif
#if DT_NODE_HAS_STATUS(DT_NODELABEL(enet2), okay)
sys_clock = CLOCK_GetFreq(kCLOCK_EnetPll1Clk);
#endif
#elif defined(CONFIG_SOC_SERIES_IMX_RT11XX)
sys_clock = CLOCK_GetRootClockFreq(kCLOCK_Root_Bus);
#else
sys_clock = CLOCK_GetFreq(kCLOCK_CoreSysClk);
#endif
ENET_GetDefaultConfig(&enet_config);
enet_config.interrupt |= kENET_RxFrameInterrupt;
enet_config.interrupt |= kENET_TxFrameInterrupt;
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
enet_config.interrupt |= kENET_MiiInterrupt;
#endif
enet_config.miiMode = kENET_RmiiMode;
if (IS_ENABLED(CONFIG_ETH_MCUX_PROMISCUOUS_MODE)) {
enet_config.macSpecialConfig |= kENET_ControlPromiscuousEnable;
}
if (IS_ENABLED(CONFIG_NET_VLAN)) {
enet_config.macSpecialConfig |= kENET_ControlVLANTagEnable;
}
if (IS_ENABLED(CONFIG_ETH_MCUX_HW_ACCELERATION)) {
enet_config.txAccelerConfig |=
kENET_TxAccelIpCheckEnabled |
kENET_TxAccelProtoCheckEnabled;
enet_config.rxAccelerConfig |=
kENET_RxAccelIpCheckEnabled |
kENET_RxAccelProtoCheckEnabled;
}
ENET_Init(context->base,
&context->enet_handle,
&enet_config,
buffer_config,
context->mac_addr,
sys_clock);
#if defined(CONFIG_PTP_CLOCK_MCUX)
ENET_AddMulticastGroup(context->base, ptp_multicast);
ENET_AddMulticastGroup(context->base, ptp_peer_multicast);
/* only for ERRATA_2579 */
context->ptp_config.channel = kENET_PtpTimerChannel3;
context->ptp_config.ptp1588ClockSrc_Hz =
CONFIG_ETH_MCUX_PTP_CLOCK_SRC_HZ;
context->clk_ratio = 1.0;
ENET_Ptp1588SetChannelMode(context->base, kENET_PtpTimerChannel3,
kENET_PtpChannelPulseHighonCompare, true);
ENET_Ptp1588Configure(context->base, &context->enet_handle,
&context->ptp_config);
#endif
#if defined(CONFIG_MDNS_RESPONDER) || defined(CONFIG_MDNS_RESOLVER)
ENET_AddMulticastGroup(context->base, mdns_multicast);
#endif
#if !defined(CONFIG_ETH_MCUX_NO_PHY_SMI)
ENET_SetSMI(context->base, sys_clock, false);
#endif
/* handle PHY setup after SMI initialization */
eth_mcux_phy_setup(context);
#if defined(CONFIG_PTP_CLOCK_MCUX)
/* Enable reclaim of tx descriptors that will have the tx timestamp */
ENET_SetTxReclaim(&context->enet_handle, true, 0);
#endif
ENET_SetCallback(&context->enet_handle, eth_callback, context);
eth_mcux_phy_start(context);
}
static int eth_init(const struct device *dev)
{
struct eth_context *context = dev->data;
#if defined(CONFIG_PINCTRL)
int err;
err = pinctrl_apply_state(context->pincfg, PINCTRL_STATE_DEFAULT);
if (err) {
return err;
}
#endif /* CONFIG_PINCTRL */
#if defined(CONFIG_NET_POWER_MANAGEMENT)
const uint32_t inst = ENET_GetInstance(context->base);
context->clock = enet_clocks[inst];
#endif
#if defined(CONFIG_ETH_MCUX_PHY_RESET)
eth_phy_reset(dev);
eth_phy_init(dev);
#endif
#if defined(CONFIG_PTP_CLOCK_MCUX)
k_mutex_init(&context->ptp_mutex);
k_sem_init(&context->ptp_ts_sem, 0, 1);
#endif
k_mutex_init(&context->rx_frame_buf_mutex);
k_mutex_init(&context->tx_frame_buf_mutex);
k_sem_init(&context->rx_thread_sem, 0, CONFIG_ETH_MCUX_RX_BUFFERS);
k_sem_init(&context->tx_buf_sem,
CONFIG_ETH_MCUX_TX_BUFFERS, CONFIG_ETH_MCUX_TX_BUFFERS);
k_work_init(&context->phy_work, eth_mcux_phy_work);
k_work_init_delayable(&context->delayed_phy_work,
eth_mcux_delayed_phy_work);
/* Start interruption-poll thread */
k_thread_create(&context->rx_thread, context->rx_thread_stack,
K_KERNEL_STACK_SIZEOF(context->rx_thread_stack),
eth_rx_thread, (void *) context, NULL, NULL,
K_PRIO_COOP(2),
0, K_NO_WAIT);
k_thread_name_set(&context->rx_thread, "mcux_eth_rx");
if (context->generate_mac) {
context->generate_mac(context->mac_addr);
}
eth_mcux_init(dev);
LOG_DBG("%s MAC %02x:%02x:%02x:%02x:%02x:%02x",
dev->name,
context->mac_addr[0], context->mac_addr[1],
context->mac_addr[2], context->mac_addr[3],
context->mac_addr[4], context->mac_addr[5]);
return 0;
}
#if defined(CONFIG_NET_IPV6)
static void net_if_mcast_cb(struct net_if *iface,
const struct net_addr *addr,
bool is_joined)
{
const struct device *dev = net_if_get_device(iface);
struct eth_context *context = dev->data;
struct net_eth_addr mac_addr;
if (addr->family != AF_INET6) {
return;
}
net_eth_ipv6_mcast_to_mac_addr(&addr->in6_addr, &mac_addr);
if (is_joined) {
ENET_AddMulticastGroup(context->base, mac_addr.addr);
} else {
ENET_LeaveMulticastGroup(context->base, mac_addr.addr);
}
}
#endif /* CONFIG_NET_IPV6 */
static void eth_iface_init(struct net_if *iface)
{
const struct device *dev = net_if_get_device(iface);
struct eth_context *context = dev->data;
#if defined(CONFIG_NET_IPV6)
static struct net_if_mcast_monitor mon;
net_if_mcast_mon_register(&mon, iface, net_if_mcast_cb);
#endif /* CONFIG_NET_IPV6 */
net_if_set_link_addr(iface, context->mac_addr,
sizeof(context->mac_addr),
NET_LINK_ETHERNET);
/* For VLAN, this value is only used to get the correct L2 driver.
* The iface pointer in context should contain the main interface
* if the VLANs are enabled.
*/
if (context->iface == NULL) {
context->iface = iface;
}
#if defined(CONFIG_NET_DSA)
dsa_register_master_tx(iface, &eth_tx);
#endif
ethernet_init(iface);
net_if_carrier_off(iface);
context->config_func();
}
static enum ethernet_hw_caps eth_mcux_get_capabilities(const struct device *dev)
{
ARG_UNUSED(dev);
return ETHERNET_HW_VLAN | ETHERNET_LINK_10BASE_T |
#if defined(CONFIG_PTP_CLOCK_MCUX)
ETHERNET_PTP |
#endif
#if defined(CONFIG_NET_DSA)
ETHERNET_DSA_MASTER_PORT |
#endif
#if defined(CONFIG_ETH_MCUX_HW_ACCELERATION)
ETHERNET_HW_TX_CHKSUM_OFFLOAD |
ETHERNET_HW_RX_CHKSUM_OFFLOAD |
#endif
ETHERNET_AUTO_NEGOTIATION_SET |
ETHERNET_LINK_100BASE_T;
}
static int eth_mcux_set_config(const struct device *dev,
enum ethernet_config_type type,
const struct ethernet_config *config)
{
struct eth_context *context = dev->data;
switch (type) {
case ETHERNET_CONFIG_TYPE_MAC_ADDRESS:
memcpy(context->mac_addr,
config->mac_address.addr,
sizeof(context->mac_addr));
ENET_SetMacAddr(context->base, context->mac_addr);
net_if_set_link_addr(context->iface, context->mac_addr,
sizeof(context->mac_addr),
NET_LINK_ETHERNET);
LOG_DBG("%s MAC set to %02x:%02x:%02x:%02x:%02x:%02x",
dev->name,
context->mac_addr[0], context->mac_addr[1],
context->mac_addr[2], context->mac_addr[3],
context->mac_addr[4], context->mac_addr[5]);
return 0;
default:
break;
}
return -ENOTSUP;
}
#if defined(CONFIG_PTP_CLOCK_MCUX)
static const struct device *eth_mcux_get_ptp_clock(const struct device *dev)
{
struct eth_context *context = dev->data;
return context->ptp_clock;
}
#endif
static const struct ethernet_api api_funcs = {
.iface_api.init = eth_iface_init,
#if defined(CONFIG_PTP_CLOCK_MCUX)
.get_ptp_clock = eth_mcux_get_ptp_clock,
#endif
.get_capabilities = eth_mcux_get_capabilities,
.set_config = eth_mcux_set_config,
#if defined(CONFIG_NET_DSA)
.send = dsa_tx,
#else
.send = eth_tx,
#endif
};
#if defined(CONFIG_PTP_CLOCK_MCUX)
static void eth_mcux_ptp_isr(const struct device *dev)
{
struct eth_context *context = dev->data;
unsigned int irq_lock_key = irq_lock();
enet_ptp_timer_channel_t channel;
/* clear channel */
for (channel = kENET_PtpTimerChannel1; channel <= kENET_PtpTimerChannel4; channel++) {
if (ENET_Ptp1588GetChannelStatus(context->base, channel)) {
ENET_Ptp1588ClearChannelStatus(context->base, channel);
}
}
ENET_TimeStampIRQHandler(context->base, &context->enet_handle);
irq_unlock(irq_lock_key);
}
#endif
#if DT_INST_IRQ_HAS_NAME(0, common) || DT_INST_IRQ_HAS_NAME(1, common)
static void eth_mcux_common_isr(const struct device *dev)
{
struct eth_context *context = dev->data;
uint32_t EIR = ENET_GetInterruptStatus(context->base);
unsigned int irq_lock_key = irq_lock();
if (EIR & (kENET_RxBufferInterrupt | kENET_RxFrameInterrupt)) {
/* disable the IRQ for RX */
context->rx_irq_num++;
#if FSL_FEATURE_ENET_QUEUE > 1
/* Only use ring 0 in this driver */
ENET_ReceiveIRQHandler(context->base, &context->enet_handle, 0);
#else
ENET_ReceiveIRQHandler(context->base, &context->enet_handle);
#endif
ENET_DisableInterrupts(context->base, kENET_RxFrameInterrupt |
kENET_RxBufferInterrupt);
}
if (EIR & kENET_TxFrameInterrupt) {
#if FSL_FEATURE_ENET_QUEUE > 1
ENET_TransmitIRQHandler(context->base, &context->enet_handle, 0);
#else
ENET_TransmitIRQHandler(context->base, &context->enet_handle);
#endif
}
if (EIR | kENET_TxBufferInterrupt) {
ENET_ClearInterruptStatus(context->base, kENET_TxBufferInterrupt);
ENET_DisableInterrupts(context->base, kENET_TxBufferInterrupt);
}
if (EIR & ENET_EIR_MII_MASK) {
k_work_submit(&context->phy_work);
ENET_ClearInterruptStatus(context->base, kENET_MiiInterrupt);
}
#if defined(CONFIG_PTP_CLOCK_MCUX)
if (EIR & ENET_TS_INTERRUPT) {
ENET_TimeStampIRQHandler(context->base, &context->enet_handle);
}
#endif
irq_unlock(irq_lock_key);
}
#endif
#if DT_INST_IRQ_HAS_NAME(0, rx) || DT_INST_IRQ_HAS_NAME(1, rx)
static void eth_mcux_rx_isr(const struct device *dev)
{
struct eth_context *context = dev->data;
ENET_DisableInterrupts(context->base, kENET_RxFrameInterrupt | kENET_RxBufferInterrupt);
ENET_ReceiveIRQHandler(context->base, &context->enet_handle);
}
#endif
#if DT_INST_IRQ_HAS_NAME(0, tx) || DT_INST_IRQ_HAS_NAME(1, tx)
static void eth_mcux_tx_isr(const struct device *dev)
{
struct eth_context *context = dev->data;
#if FSL_FEATURE_ENET_QUEUE > 1
ENET_TransmitIRQHandler(context->base, &context->enet_handle, 0);
#else
ENET_TransmitIRQHandler(context->base, &context->enet_handle);
#endif
}
#endif
#if DT_INST_IRQ_HAS_NAME(0, err) || DT_INST_IRQ_HAS_NAME(1, err)
static void eth_mcux_err_isr(const struct device *dev)
{
struct eth_context *context = dev->data;
uint32_t pending = ENET_GetInterruptStatus(context->base);
if (pending & ENET_EIR_MII_MASK) {
k_work_submit(&context->phy_work);
ENET_ClearInterruptStatus(context->base, kENET_MiiInterrupt);
}
}
#endif
#if defined(CONFIG_SOC_SERIES_IMX_RT10XX)
#define ETH_MCUX_UNIQUE_ID (OCOTP->CFG1 ^ OCOTP->CFG2)
#elif defined(CONFIG_SOC_SERIES_IMX_RT11XX)
#define ETH_MCUX_UNIQUE_ID (OCOTP->FUSEN[40].FUSE)
#elif defined(CONFIG_SOC_SERIES_KINETIS_K6X)
#define ETH_MCUX_UNIQUE_ID (SIM->UIDH ^ SIM->UIDMH ^ SIM->UIDML ^ SIM->UIDL)
#else
#error "Unsupported SOC"
#endif
#define ETH_MCUX_NONE
#define ETH_MCUX_IRQ_INIT(n, name) \
do { \
IRQ_CONNECT(DT_INST_IRQ_BY_NAME(n, name, irq), \
DT_INST_IRQ_BY_NAME(n, name, priority), \
eth_mcux_##name##_isr, \
DEVICE_DT_INST_GET(n), \
0); \
irq_enable(DT_INST_IRQ_BY_NAME(n, name, irq)); \
} while (false)
#define ETH_MCUX_IRQ(n, name) \
COND_CODE_1(DT_INST_IRQ_HAS_NAME(n, name), \
(ETH_MCUX_IRQ_INIT(n, name)), \
(ETH_MCUX_NONE))
#if defined(CONFIG_PTP_CLOCK_MCUX)
#define PTP_INST_NODEID(n) DT_INST_CHILD(n, ptp)
#define ETH_MCUX_IRQ_PTP_INIT(n) \
do { \
IRQ_CONNECT(DT_IRQ_BY_NAME(PTP_INST_NODEID(n), ieee1588_tmr, irq), \
DT_IRQ_BY_NAME(PTP_INST_NODEID(n), ieee1588_tmr, priority), \
eth_mcux_ptp_isr, \
DEVICE_DT_INST_GET(n), \
0); \
irq_enable(DT_IRQ_BY_NAME(PTP_INST_NODEID(n), ieee1588_tmr, irq)); \
} while (false)
#define ETH_MCUX_IRQ_PTP(n) \
COND_CODE_1(DT_NODE_HAS_STATUS(PTP_INST_NODEID(n), okay), \
(ETH_MCUX_IRQ_PTP_INIT(n)), \
(ETH_MCUX_NONE))
#define ETH_MCUX_PTP_FRAMEINFO_ARRAY(n) \
static enet_frame_info_t \
eth##n##_tx_frameinfo_array[CONFIG_ETH_MCUX_TX_BUFFERS];
#define ETH_MCUX_PTP_FRAMEINFO(n) \
.txFrameInfo = eth##n##_tx_frameinfo_array,
#else
#define ETH_MCUX_IRQ_PTP(n)
#define ETH_MCUX_PTP_FRAMEINFO_ARRAY(n)
#define ETH_MCUX_PTP_FRAMEINFO(n) \
.txFrameInfo = NULL,
#endif
#define ETH_MCUX_GENERATE_MAC_RANDOM(n) \
static void generate_eth##n##_mac(uint8_t *mac_addr) \
{ \
gen_random_mac(mac_addr, \
FREESCALE_OUI_B0, \
FREESCALE_OUI_B1, \
FREESCALE_OUI_B2); \
}
#define ETH_MCUX_GENERATE_MAC_UNIQUE(n) \
static void generate_eth##n##_mac(uint8_t *mac_addr) \
{ \
uint32_t id = ETH_MCUX_UNIQUE_ID; \
\
mac_addr[0] = FREESCALE_OUI_B0; \
mac_addr[0] |= 0x02; /* force LAA bit */ \
mac_addr[1] = FREESCALE_OUI_B1; \
mac_addr[2] = FREESCALE_OUI_B2; \
mac_addr[3] = id >> 8; \
mac_addr[4] = id >> 16; \
mac_addr[5] = id >> 0; \
mac_addr[5] += n; \
}
#define ETH_MCUX_GENERATE_MAC(n) \
COND_CODE_1(DT_INST_PROP(n, zephyr_random_mac_address), \
(ETH_MCUX_GENERATE_MAC_RANDOM(n)), \
(ETH_MCUX_GENERATE_MAC_UNIQUE(n)))
#define ETH_MCUX_MAC_ADDR_LOCAL(n) \
.mac_addr = DT_INST_PROP(n, local_mac_address), \
.generate_mac = NULL,
#define ETH_MCUX_MAC_ADDR_GENERATE(n) \
.mac_addr = {0}, \
.generate_mac = generate_eth##n##_mac,
#define ETH_MCUX_MAC_ADDR(n) \
COND_CODE_1(ETH_MCUX_MAC_ADDR_TO_BOOL(n), \
(ETH_MCUX_MAC_ADDR_LOCAL(n)), \
(ETH_MCUX_MAC_ADDR_GENERATE(n)))
#define ETH_MCUX_POWER_INIT(n) \
.clock_dev = DEVICE_DT_GET(DT_INST_CLOCKS_CTLR(n)), \
#define ETH_MCUX_POWER(n) \
COND_CODE_1(CONFIG_NET_POWER_MANAGEMENT, \
(ETH_MCUX_POWER_INIT(n)), \
(ETH_MCUX_NONE))
#define ETH_MCUX_GEN_MAC(n) \
COND_CODE_0(ETH_MCUX_MAC_ADDR_TO_BOOL(n), \
(ETH_MCUX_GENERATE_MAC(n)), \
(ETH_MCUX_NONE))
/*
* In the below code we explicitly define
* ETH_MCUX_MAC_ADDR_TO_BOOL_0 for the '0' instance of enet driver.
*
* For instance N one shall add definition for ETH_MCUX_MAC_ADDR_TO_BOOL_N
*/
#if (NODE_HAS_VALID_MAC_ADDR(DT_DRV_INST(0))) == 0
#define ETH_MCUX_MAC_ADDR_TO_BOOL_0 0
#else
#define ETH_MCUX_MAC_ADDR_TO_BOOL_0 1
#endif
#define ETH_MCUX_MAC_ADDR_TO_BOOL(n) ETH_MCUX_MAC_ADDR_TO_BOOL_##n
#if defined(CONFIG_PINCTRL)
#define ETH_MCUX_PINCTRL_DEFINE(n) PINCTRL_DT_INST_DEFINE(n);
#define ETH_MCUX_PINCTRL_INIT(n) .pincfg = PINCTRL_DT_INST_DEV_CONFIG_GET(n),
#else
#define ETH_MCUX_PINCTRL_DEFINE(n)
#define ETH_MCUX_PINCTRL_INIT(n)
#endif
#if DT_NODE_HAS_STATUS(DT_CHOSEN(zephyr_dtcm), okay) && \
CONFIG_ETH_MCUX_USE_DTCM_FOR_DMA_BUFFER
/* Use DTCM for hardware DMA buffers */
#define _mcux_dma_desc __dtcm_bss_section
#define _mcux_dma_buffer __dtcm_noinit_section
#define _mcux_driver_buffer __dtcm_noinit_section
#elif defined(CONFIG_NOCACHE_MEMORY)
#define _mcux_dma_desc __nocache
#define _mcux_dma_buffer __nocache
#define _mcux_driver_buffer
#else
#define _mcux_dma_desc
#define _mcux_dma_buffer
#define _mcux_driver_buffer
#endif
#if defined(CONFIG_ETH_MCUX_PHY_RESET)
#define ETH_MCUX_PHY_GPIOS(n) \
.int_gpio = GPIO_DT_SPEC_INST_GET(n, int_gpios), \
.reset_gpio = GPIO_DT_SPEC_INST_GET(n, reset_gpios),
#else
#define ETH_MCUX_PHY_GPIOS(n)
#endif
#define ETH_MCUX_INIT(n) \
ETH_MCUX_GEN_MAC(n) \
\
ETH_MCUX_PINCTRL_DEFINE(n) \
\
static void eth##n##_config_func(void); \
static _mcux_driver_buffer uint8_t \
tx_enet_frame_##n##_buf[NET_ETH_MAX_FRAME_SIZE]; \
static _mcux_driver_buffer uint8_t \
rx_enet_frame_##n##_buf[NET_ETH_MAX_FRAME_SIZE]; \
static status_t _MDIO_Write(uint8_t phyAddr, uint8_t regAddr, uint16_t data) \
{ \
return ENET_MDIOWrite((ENET_Type *)DT_INST_REG_ADDR(n), phyAddr, regAddr, data);\
}; \
\
static status_t _MDIO_Read(uint8_t phyAddr, uint8_t regAddr, uint16_t *pData) \
{ \
return ENET_MDIORead((ENET_Type *)DT_INST_REG_ADDR(n), phyAddr, regAddr, pData); \
}; \
\
static struct _phy_resource eth##n##_phy_resource = { \
.read = _MDIO_Read, \
.write = _MDIO_Write \
}; \
static phy_handle_t eth##n##_phy_handle = { \
.resource = (void *)&eth##n##_phy_resource \
}; \
static struct _phy_resource eth##n##_phy_config; \
\
static struct eth_context eth##n##_context = { \
.base = (ENET_Type *)DT_INST_REG_ADDR(n), \
.config_func = eth##n##_config_func, \
.phy_config = &eth##n##_phy_config, \
.phy_addr = DT_INST_PROP(n, phy_addr), \
.phy_duplex = kPHY_FullDuplex, \
.phy_speed = kPHY_Speed100M, \
.phy_handle = &eth##n##_phy_handle, \
.tx_frame_buf = tx_enet_frame_##n##_buf, \
.rx_frame_buf = rx_enet_frame_##n##_buf, \
ETH_MCUX_PINCTRL_INIT(n) \
ETH_MCUX_PHY_GPIOS(n) \
ETH_MCUX_MAC_ADDR(n) \
ETH_MCUX_POWER(n) \
}; \
\
static __aligned(ENET_BUFF_ALIGNMENT) \
_mcux_dma_desc \
enet_rx_bd_struct_t \
eth##n##_rx_buffer_desc[CONFIG_ETH_MCUX_RX_BUFFERS]; \
\
static __aligned(ENET_BUFF_ALIGNMENT) \
_mcux_dma_desc \
enet_tx_bd_struct_t \
eth##n##_tx_buffer_desc[CONFIG_ETH_MCUX_TX_BUFFERS]; \
\
static uint8_t __aligned(ENET_BUFF_ALIGNMENT) \
_mcux_dma_buffer \
eth##n##_rx_buffer[CONFIG_ETH_MCUX_RX_BUFFERS] \
[ETH_MCUX_BUFFER_SIZE]; \
\
static uint8_t __aligned(ENET_BUFF_ALIGNMENT) \
_mcux_dma_buffer \
eth##n##_tx_buffer[CONFIG_ETH_MCUX_TX_BUFFERS] \
[ETH_MCUX_BUFFER_SIZE]; \
\
ETH_MCUX_PTP_FRAMEINFO_ARRAY(n) \
\
static const enet_buffer_config_t eth##n##_buffer_config = { \
.rxBdNumber = CONFIG_ETH_MCUX_RX_BUFFERS, \
.txBdNumber = CONFIG_ETH_MCUX_TX_BUFFERS, \
.rxBuffSizeAlign = ETH_MCUX_BUFFER_SIZE, \
.txBuffSizeAlign = ETH_MCUX_BUFFER_SIZE, \
.rxBdStartAddrAlign = eth##n##_rx_buffer_desc, \
.txBdStartAddrAlign = eth##n##_tx_buffer_desc, \
.rxBufferAlign = eth##n##_rx_buffer[0], \
.txBufferAlign = eth##n##_tx_buffer[0], \
.rxMaintainEnable = true, \
.txMaintainEnable = true, \
ETH_MCUX_PTP_FRAMEINFO(n) \
}; \
\
PM_DEVICE_DT_INST_DEFINE(n, eth_mcux_device_pm_action); \
\
ETH_NET_DEVICE_DT_INST_DEFINE(n, \
eth_init, \
PM_DEVICE_DT_INST_GET(n), \
&eth##n##_context, \
&eth##n##_buffer_config, \
CONFIG_ETH_INIT_PRIORITY, \
&api_funcs, \
NET_ETH_MTU); \
\
static void eth##n##_config_func(void) \
{ \
ETH_MCUX_IRQ(n, rx); \
ETH_MCUX_IRQ(n, tx); \
ETH_MCUX_IRQ(n, err); \
ETH_MCUX_IRQ(n, common); \
ETH_MCUX_IRQ_PTP(n); \
} \
DT_INST_FOREACH_STATUS_OKAY(ETH_MCUX_INIT)
#if defined(CONFIG_PTP_CLOCK_MCUX)
struct ptp_context {
struct eth_context *eth_context;
#if defined(CONFIG_PINCTRL)
const struct pinctrl_dev_config *pincfg;
#endif /* CONFIG_PINCTRL */
};
#if defined(CONFIG_PINCTRL)
#define ETH_MCUX_PTP_PINCTRL_DEFINE(n) PINCTRL_DT_DEFINE(n);
#define ETH_MCUX_PTP_PINCTRL_INIT(n) .pincfg = PINCTRL_DT_DEV_CONFIG_GET(n),
#else
#define ETH_MCUX_PTP_PINCTRL_DEFINE(n)
#define ETH_MCUX_PTP_PINCTRL_INIT(n)
#endif /* CONFIG_PINCTRL */
ETH_MCUX_PTP_PINCTRL_DEFINE(DT_NODELABEL(ptp))
static struct ptp_context ptp_mcux_0_context = {
ETH_MCUX_PTP_PINCTRL_INIT(DT_NODELABEL(ptp))
};
static int ptp_clock_mcux_set(const struct device *dev,
struct net_ptp_time *tm)
{
struct ptp_context *ptp_context = dev->data;
struct eth_context *context = ptp_context->eth_context;
enet_ptp_time_t enet_time;
enet_time.second = tm->second;
enet_time.nanosecond = tm->nanosecond;
ENET_Ptp1588SetTimer(context->base, &context->enet_handle, &enet_time);
return 0;
}
static int ptp_clock_mcux_get(const struct device *dev,
struct net_ptp_time *tm)
{
struct ptp_context *ptp_context = dev->data;
struct eth_context *context = ptp_context->eth_context;
enet_ptp_time_t enet_time;
ENET_Ptp1588GetTimer(context->base, &context->enet_handle, &enet_time);
tm->second = enet_time.second;
tm->nanosecond = enet_time.nanosecond;
return 0;
}
static int ptp_clock_mcux_adjust(const struct device *dev, int increment)
{
struct ptp_context *ptp_context = dev->data;
struct eth_context *context = ptp_context->eth_context;
int key, ret;
ARG_UNUSED(dev);
if ((increment <= (int32_t)(-NSEC_PER_SEC)) ||
(increment >= (int32_t)NSEC_PER_SEC)) {
ret = -EINVAL;
} else {
key = irq_lock();
if (context->base->ATPER != NSEC_PER_SEC) {
ret = -EBUSY;
} else {
/* Seconds counter is handled by software. Change the
* period of one software second to adjust the clock.
*/
context->base->ATPER = NSEC_PER_SEC - increment;
ret = 0;
}
irq_unlock(key);
}
return ret;
}
static int ptp_clock_mcux_rate_adjust(const struct device *dev, double ratio)
{
const int hw_inc = NSEC_PER_SEC / CONFIG_ETH_MCUX_PTP_CLOCK_SRC_HZ;
struct ptp_context *ptp_context = dev->data;
struct eth_context *context = ptp_context->eth_context;
int corr;
int32_t mul;
double val;
/* No change needed. */
if ((ratio > 1.0 && ratio - 1.0 < 0.00000001) ||
(ratio < 1.0 && 1.0 - ratio < 0.00000001)) {
return 0;
}
ratio *= context->clk_ratio;
/* Limit possible ratio. */
if ((ratio > 1.0 + 1.0/(2 * hw_inc)) ||
(ratio < 1.0 - 1.0/(2 * hw_inc))) {
return -EINVAL;
}
/* Save new ratio. */
context->clk_ratio = ratio;
if (ratio < 1.0) {
corr = hw_inc - 1;
val = 1.0 / (hw_inc * (1.0 - ratio));
} else if (ratio > 1.0) {
corr = hw_inc + 1;
val = 1.0 / (hw_inc * (ratio - 1.0));
} else {
val = 0;
corr = hw_inc;
}
if (val >= INT32_MAX) {
/* Value is too high.
* It is not possible to adjust the rate of the clock.
*/
mul = 0;
} else {
mul = val;
}
k_mutex_lock(&context->ptp_mutex, K_FOREVER);
ENET_Ptp1588AdjustTimer(context->base, corr, mul);
k_mutex_unlock(&context->ptp_mutex);
return 0;
}
static const struct ptp_clock_driver_api api = {
.set = ptp_clock_mcux_set,
.get = ptp_clock_mcux_get,
.adjust = ptp_clock_mcux_adjust,
.rate_adjust = ptp_clock_mcux_rate_adjust,
};
static int ptp_mcux_init(const struct device *port)
{
const struct device *const eth_dev = DEVICE_DT_GET(DT_NODELABEL(enet));
struct eth_context *context = eth_dev->data;
struct ptp_context *ptp_context = port->data;
#if defined(CONFIG_PINCTRL)
int err;
err = pinctrl_apply_state(ptp_context->pincfg, PINCTRL_STATE_DEFAULT);
if (err) {
return err;
}
#endif /* CONFIG_PINCTRL */
context->ptp_clock = port;
ptp_context->eth_context = context;
return 0;
}
DEVICE_DEFINE(mcux_ptp_clock_0, PTP_CLOCK_NAME, ptp_mcux_init,
NULL, &ptp_mcux_0_context, NULL, POST_KERNEL,
CONFIG_ETH_MCUX_PTP_CLOCK_INIT_PRIO, &api);
#endif /* CONFIG_PTP_CLOCK_MCUX */