dts/bindings/sensor/nxp,fxos8700-common.yaml

# Copyright (c) 2018, NXP
# SPDX-License-Identifier: Apache-2.0

description: FXOS8700 6-axis accelerometer/magnetometer sensor

include: sensor-device.yaml

properties:
  reset-gpios:
    type: phandle-array
    description: |
      RST pin
      This pin defaults to active high when consumed by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.

  int1-gpios:
    type: phandle-array
    description: |
      INT1 pin
      This pin defaults to active low when produced by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.

  int2-gpios:
    type: phandle-array
    description: |
      INT2 pin
      This pin defaults to active low when produced by the sensor.
      The property value should ensure the flags properly describe
      the signal that is presented to the driver.

  range:
    type: int
    default: 8
    description: Range in g
    enum:
      - 8 # 8g (0.976 mg/LSB)
      - 4 # 4g (0.488 mg/LSB)
      - 2 # 2g (0.244 mg/LSB)

  power-mode:
    type: int
    default: 0
    description: Power mode
    enum:
      - 0 # Normal
      - 1 # Low noise, low power
      - 2 # High resolution
      - 3 # Low power

  pulse-cfg:
    type: int
    default: 0x3f
    description: Pulse configuration register

  pulse-thsx:
    type: int
    default: 0x20
    description: |
      Pulse X-axis threshold
      Threshold to start the pulse-event detection procedure on the X-axis.
      Threshold values for each axis are unsigned 7-bit numbers with a fixed
      resolution of 0.063 g/LSB, corresponding to an 8g acceleration
      full-scale range.

  pulse-thsy:
    type: int
    default: 0x20
    description: |
      Pulse Y-axis threshold
      Threshold to start the pulse-event detection procedure on the Y-axis.
      Threshold values for each axis are unsigned 7-bit numbers with a fixed
      resolution of 0.063 g/LSB, corresponding to an 8g acceleration
      full-scale range.

  pulse-thsz:
    type: int
    default: 0x40
    description: |
      Pulse Z-axis threshold
      Threshold to start the pulse-event detection procedure on the Z-axis.
      Threshold values for each axis are unsigned 7-bit numbers with a fixed
      resolution of 0.063 g/LSB, corresponding to an 8g acceleration
      full-scale range.

  pulse-tmlt:
    type: int
    default: 0x18
    description: |
      Pulse time limit
      The maximum time interval that can elapse between the start of the
      acceleration on the selected channel exceeding the specified threshold
      and the end when the channel acceleration goes back below the specified
      threshold. The resolution depends upon the sample rate (ODR) and the
      high-pass filter configuration (HP_FILTER_CUTOFF[pls_hpf_en]). For
      ODR=800 Hz and pls_hpf_en=0, the resolution is 0.625 ms/LSB.

  pulse-ltcy:
    type: int
    default: 0x28
    description: |
      Pulse latency
      The time interval that starts after the first pulse detection where the
      pulse-detection function ignores the start of a new pulse. The
      resolution depends upon the sample rate (ODR) and the high-pass filter
      configuration (HP_FILTER_CUTOFF[pls_hpf_en]). For ODR=800 Hz and
      pls_hpf_en=0, the resolution is 1.25 ms/LSB.

  pulse-wind:
    type: int
    default: 0x3c
    description: |
      Pulse window
      The maximum interval of time that can elapse after the end of the
      latency interval in which the start of the second pulse event must be
      detected provided the device has been configured for double pulse
      detection. The detected second pulse width must be shorter than the
      time limit constraint specified by the PULSE_TMLT register, but the end
      of the double pulse need not finish within the time specified by the
      PULSE_WIND register. The resolution depends upon the sample rate (ODR)
      and the high-pass filter configuration (HP_FILTER_CUTOFF[pls_hpf_en]).
      For ODR=800 Hz and pls_hpf_en=0, the resolution is 1.25 ms/LSB.

  mag-vecm-cfg:
    type: int
    default: 0x4e
    description: Magnetic vector-magnitude configuration register

  mag-vecm-ths-msb:
    type: int
    default: 0x00
    description: |
      Magnetic vector-magnitude threshold most significant byte.
      Resolution is 0.1 uT/LSB.

  mag-vecm-ths-lsb:
    type: int
    default: 0x5a
    description: |
      Magnetic vector-magnitude threshold least significant byte.
      Resolution is 0.1 uT/LSB.