blob: 39b65271fd4c9642867f49f29855d1be025fa521 [file] [log] [blame]
/*
* Copyright (c) 2023 TiaC Systems
* Copyright 2019,2023-2024 NXP
*
* SPDX-License-Identifier: Apache-2.0
*/
/dts-v1/;
#include <nxp/nxp_rt1010.dtsi>
#include "mimxrt1010_evk-pinctrl.dtsi"
#include <zephyr/dt-bindings/input/input-event-codes.h>
/ {
model = "NXP MIMXRT1010-EVK board";
compatible = "nxp,mimxrt1010";
aliases {
led0 = &green_led;
sw0 = &user_button;
};
chosen {
zephyr,sram = &ocram;
zephyr,itcm = &itcm;
zephyr,dtcm = &dtcm;
zephyr,console = &lpuart1;
zephyr,shell-uart = &lpuart1;
zephyr,flash = &at25sf128a;
zephyr,flash-controller = &at25sf128a;
zephyr,code-partition = &slot0_partition;
};
leds {
compatible = "gpio-leds";
green_led: led-1 {
gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
label = "User LD1";
};
};
gpio_keys {
compatible = "gpio-keys";
user_button: button-1 {
label = "User SW4";
gpios = <&gpio2 5 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>;
zephyr,code = <INPUT_KEY_0>;
};
};
arduino_header: connector {
compatible = "arduino-header-r3";
#gpio-cells = <2>;
gpio-map-mask = <0xffffffff 0xffffffc0>;
gpio-map-pass-thru = <0 0x3f>;
gpio-map = <0 0 &gpio1 21 0>, /* A0 */
<1 0 &gpio1 23 0>, /* A1 */
<2 0 &gpio1 24 0>, /* A2 */
<3 0 &gpio1 28 0>, /* A3 */
<4 0 &gpio1 15 0>, /* A4 (shared with D6) */
<5 0 &gpio1 16 0>, /* A5 (shared with D7) */
<6 0 &gpio1 9 0>, /* D0 */
<7 0 &gpio1 10 0>, /* D1 */
<8 0 &gpio1 19 0>, /* D2 (shared with D10) */
<9 0 &gpio1 20 0>, /* D3 (shared with D13) */
/* R800 not populated, D4 */
/* R793 not populated, D5 (shared with D14) */
<12 0 &gpio1 15 0>, /* D6 (shared with A4) */
<13 0 &gpio1 16 0>, /* D7 (shared with A5) */
<14 0 &gpio2 2 0>, /* D8 */
/* R795 not populated, D9 */
<16 0 &gpio1 19 0>, /* D10 (shared with D2) */
<17 0 &gpio1 18 0>, /* D11 */
<18 0 &gpio1 17 0>, /* D12 */
<19 0 &gpio1 20 0>, /* D13 (shared with D3) */
<20 0 &gpio1 1 0>, /* D14 */
<21 0 &gpio1 2 0>; /* D15 */
};
};
arduino_serial: &lpuart1 {};
&lpuart4 {
pinctrl-0 = <&pinmux_lpuart4>;
pinctrl-1 = <&pinmux_lpuart4_sleep>;
pinctrl-names = "default", "sleep";
};
&flexspi {
status = "okay";
reg = <0x400a0000 0x4000>, <0x60000000 DT_SIZE_M(16)>;
at25sf128a: at25sf128a@0 {
compatible = "nxp,imx-flexspi-nor";
size = <DT_SIZE_M(16 * 8)>;
reg = <0>;
spi-max-frequency = <133000000>;
status = "okay";
jedec-id = [1f 89 01];
erase-block-size = <4096>;
write-block-size = <1>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
boot_partition: partition@0 {
label = "mcuboot";
reg = <0x00000000 DT_SIZE_K(64)>;
};
slot0_partition: partition@10000 {
label = "image-0";
reg = <0x00010000 DT_SIZE_M(7)>;
};
slot1_partition: partition@710000 {
label = "image-1";
reg = <0x00710000 DT_SIZE_M(7)>;
};
storage_partition: partition@E10000 {
label = "storage";
reg = <0x00E10000 DT_SIZE_K(1984)>;
};
};
};
};
arduino_i2c: &lpi2c1 {
status = "okay";
pinctrl-0 = <&pinmux_lpi2c1>;
pinctrl-names = "default";
};
&lpuart1 {
status = "okay";
current-speed = <115200>;
pinctrl-0 = <&pinmux_lpuart1>;
pinctrl-1 = <&pinmux_lpuart1_sleep>;
pinctrl-names = "default", "sleep";
};
arduino_spi: &lpspi1 {
status = "okay";
/* DMA channels 0 and 1, muxed to LPSPI1 RX and TX */
dmas = <&edma0 0 13>, <&edma0 1 14>;
dma-names = "rx", "tx";
pinctrl-0 = <&pinmux_lpspi1>;
pinctrl-names = "default";
};
zephyr_udc0: &usb1 {
status = "okay";
};
&adc1 {
status = "okay";
pinctrl-0 = <&pinmux_adc1>;
pinctrl-names = "default";
};
&sai1 {
pinctrl-0 = <&pinmux_sai1>;
pinctrl-names = "default";
};
&edma0 {
status = "okay";
};
/* GPT and Systick are enabled. If power management is enabled, the GPT
* timer will be used instead of systick, as allows the core clock to
* be gated.
*/
&gpt_hw_timer {
status = "okay";
};
&systick {
status = "okay";
};
&pit0 {
status = "okay";
};