| /* |
| * Copyright (c) 2018 Phytec Messtechnik GmbH |
| * Copyright (c) 2017 Linaro Limited |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| #include "reel_board-pinctrl.dtsi" |
| |
| / { |
| chosen { |
| zephyr,ieee802154 = &ieee802154; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| red_led: led_0 { |
| gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; |
| label = "User D3 red"; |
| }; |
| green_led: led_1 { |
| gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; |
| label = "User D3 green"; |
| }; |
| blue_led: led_2 { |
| gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; |
| label = "User D3 blue"; |
| }; |
| }; |
| |
| pwmleds { |
| compatible = "pwm-leds"; |
| red_pwm_led: pwm_led_0 { |
| pwms = <&pwm0 1 PWM_MSEC(20) PWM_POLARITY_INVERTED>; |
| }; |
| green_pwm_led: pwm_led_1 { |
| pwms = <&pwm0 2 PWM_MSEC(20) PWM_POLARITY_INVERTED>; |
| }; |
| blue_pwm_led: pwm_led_2 { |
| pwms = <&pwm0 3 PWM_MSEC(20) PWM_POLARITY_INVERTED>; |
| }; |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| user_button: button_0 { |
| gpios = <&gpio0 7 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| label = "User Button"; |
| }; |
| }; |
| |
| arduino_header: connector { |
| compatible = "arduino-header-r3"; |
| #gpio-cells = <2>; |
| gpio-map-mask = <0xffffffff 0xffffffc0>; |
| gpio-map-pass-thru = <0 0x3f>; |
| gpio-map = <0 0 &gpio0 3 0>, /* A0 */ |
| <1 0 &gpio0 4 0>, /* A1 */ |
| <2 0 &gpio0 28 0>, /* A2 */ |
| <3 0 &gpio0 29 0>, /* A3 */ |
| <4 0 &gpio0 30 0>, /* A4 */ |
| <5 0 &gpio0 31 0>, /* A5 */ |
| <6 0 &gpio1 1 0>, /* D0 */ |
| <7 0 &gpio1 2 0>, /* D1 */ |
| <8 0 &gpio1 3 0>, /* D2 */ |
| <9 0 &gpio1 4 0>, /* D3 */ |
| <10 0 &gpio1 5 0>, /* D4 */ |
| <11 0 &gpio1 6 0>, /* D5 */ |
| <12 0 &gpio1 7 0>, /* D6 */ |
| <13 0 &gpio1 8 0>, /* D7 */ |
| <14 0 &gpio1 10 0>, /* D8 */ |
| <15 0 &gpio1 11 0>, /* D9 */ |
| <16 0 &gpio1 12 0>, /* D10 */ |
| <17 0 &gpio1 13 0>, /* D11 */ |
| <18 0 &gpio1 14 0>, /* D12 */ |
| <19 0 &gpio1 15 0>, /* D13 */ |
| <20 0 &gpio0 26 0>, /* D14 */ |
| <21 0 &gpio0 27 0>; /* D15 */ |
| }; |
| |
| aliases { |
| led0 = &red_led; |
| led1 = &green_led; |
| led2 = &blue_led; |
| pwm-led0 = &red_pwm_led; |
| pwm-led1 = &green_pwm_led; |
| pwm-led2 = &blue_pwm_led; |
| red-pwm-led = &red_pwm_led; |
| green-pwm-led = &green_pwm_led; |
| blue-pwm-led = &blue_pwm_led; |
| sw0 = &user_button; |
| accel0 = &mma8642fc; |
| }; |
| }; |
| |
| &gpiote { |
| status = "okay"; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| compatible = "nordic,nrf-uart"; |
| current-speed = <115200>; |
| status = "okay"; |
| pinctrl-0 = <&uart0_default>; |
| pinctrl-1 = <&uart0_sleep>; |
| pinctrl-names = "default", "sleep"; |
| }; |
| |
| arduino_serial: &uart1 { |
| status = "okay"; |
| current-speed = <115200>; |
| pinctrl-0 = <&uart1_default>; |
| pinctrl-1 = <&uart1_sleep>; |
| pinctrl-names = "default", "sleep"; |
| }; |
| |
| arduino_i2c: &i2c0 { |
| compatible = "nordic,nrf-twim"; |
| status = "okay"; |
| clock-frequency = <I2C_BITRATE_FAST>; |
| |
| pinctrl-0 = <&i2c0_default>; |
| pinctrl-1 = <&i2c0_sleep>; |
| pinctrl-names = "default", "sleep"; |
| mma8642fc: mma8652fc@1d { |
| compatible = "nxp,fxos8700","nxp,mma8652fc"; |
| reg = <0x1d>; |
| int1-gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; |
| int2-gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; |
| }; |
| |
| ti_hdc@43 { |
| compatible = "ti,hdc","ti,hdc1010"; |
| reg = <0x43>; |
| drdy-gpios = <&gpio0 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| }; |
| |
| apds9960@39 { |
| compatible = "avago,apds9960"; |
| reg = <0x39>; |
| int-gpios = <&gpio0 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; |
| }; |
| }; |
| |
| &pwm0 { |
| status = "okay"; |
| pinctrl-0 = <&pwm0_default>; |
| pinctrl-1 = <&pwm0_sleep>; |
| pinctrl-names = "default", "sleep"; |
| }; |
| |
| &ieee802154 { |
| status = "okay"; |
| }; |
| |
| arduino_spi: &spi3 { |
| status = "okay"; |
| cs-gpios = <&arduino_header 16 GPIO_ACTIVE_LOW>; /* D10 */ |
| pinctrl-0 = <&spi3_default>; |
| pinctrl-1 = <&spi3_sleep>; |
| pinctrl-names = "default", "sleep"; |
| }; |
| |
| &flash0 { |
| |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0x0000C000>; |
| }; |
| slot0_partition: partition@c000 { |
| label = "image-0"; |
| reg = <0x0000C000 0x00067000>; |
| }; |
| slot1_partition: partition@73000 { |
| label = "image-1"; |
| reg = <0x00073000 0x00067000>; |
| }; |
| scratch_partition: partition@da000 { |
| label = "image-scratch"; |
| reg = <0x000da000 0x0001e000>; |
| }; |
| |
| /* |
| * The flash starting at 0x000f8000 and ending at |
| * 0x000fffff is reserved for use by the application. |
| */ |
| |
| /* |
| * Storage partition will be used by FCB/LittleFS/NVS |
| * if enabled. |
| */ |
| storage_partition: partition@f8000 { |
| label = "storage"; |
| reg = <0x000f8000 0x00008000>; |
| }; |
| }; |
| }; |
| |
| zephyr_udc0: &usbd { |
| compatible = "nordic,nrf-usbd"; |
| status = "okay"; |
| }; |