blob: b776d3756eb40a8f4322053b26420c5607de051f [file] [log] [blame]
# IPv6 Options
# Copyright (c) 2016 Intel Corporation.
# SPDX-License-Identifier: Apache-2.0
menuconfig NET_IPV6
bool "IPv6"
default y
help
Enable IPv6 support. This should be selected by default as there
is limited set of network bearers provided that support IPv4.
if NET_IPV6
config NET_IF_MAX_IPV6_COUNT
int "Max number of IPv6 network interfaces in the system"
default BT_MAX_CONN if NET_L2_BT
default NET_VLAN_COUNT if NET_VLAN
default 2 if NET_LOOPBACK
default 1
help
This tells how many network interfaces there will be in the system
that will have IPv6 enabled.
config NET_IF_UNICAST_IPV6_ADDR_COUNT
int "Max number of unicast IPv6 addresses per network interface"
default 6 if NET_L2_OPENTHREAD
default 3 if NET_LOOPBACK
default 2
config NET_IF_MCAST_IPV6_ADDR_COUNT
int "Max number of multicast IPv6 addresses per network interface"
default 8 if NET_L2_OPENTHREAD
default 3
config NET_IF_IPV6_PREFIX_COUNT
int "Max number of IPv6 prefixes per network interface"
default 2
if NET_NATIVE_IPV6
config NET_INITIAL_HOP_LIMIT
int "Initial hop limit for a connection"
default 64
help
The value should be > 0
config NET_IPV6_MAX_NEIGHBORS
int "How many IPv6 neighbors are supported"
default 8
range 1 254
help
The value depends on your network needs.
config NET_IPV6_FRAGMENT
bool "Support IPv6 fragmentation"
help
IPv6 fragmentation is disabled by default. This saves memory and
should not cause issues normally as we support anyway the minimum
length IPv6 packets (1280 bytes). If you enable fragmentation
support, please increase amount of RX data buffers so that larger
than 1280 byte packets can be received.
config NET_IPV6_FRAGMENT_MAX_COUNT
int "How many packets to reassemble at a time"
range 1 16
default 1
depends on NET_IPV6_FRAGMENT
help
How many fragmented IPv6 packets can be waiting reassembly
simultaneously. Each fragment count might use up to 1280 bytes
of memory so you need to plan this and increase the network buffer
count.
config NET_IPV6_FRAGMENT_MAX_PKT
int "How many fragments can be handled to reassemble a packet"
default 2
depends on NET_IPV6_FRAGMENT
help
Incoming fragments are stored in per-packet queue before being
reassembled. This value defines the number of fragments that
can be handled at the same time to reassemble a single packet.
We do not have to accept IPv6 packets larger than 1500 bytes
(RFC 2460 ch 5). This means that we should receive everything
within the first two fragments. The first one being 1280 bytes and
the second one 220 bytes.
You can increase this value if you expect packets with more
than two fragments.
config NET_IPV6_FRAGMENT_TIMEOUT
int "How long to wait the fragments to receive"
range 1 60
default 5
depends on NET_IPV6_FRAGMENT
help
How long to wait for IPv6 fragment to arrive before the reassembly
will timeout. RFC 2460 chapter 4.5 tells to wait for 60 seconds but
this might be too long in memory constrained devices. This value
is in seconds.
config NET_IPV6_MLD
bool "Multicast Listener Discovery support"
default y
help
The value depends on your network needs. MLD should normally
be active. Currently we support only MLDv2. See RFC 3810 for
details.
config NET_IPV6_NBR_CACHE
bool "Neighbor cache"
default y
help
The value depends on your network needs. Neighbor cache should
normally be active.
config NET_IPV6_ND
bool "Activate neighbor discovery"
depends on NET_IPV6_NBR_CACHE
default y
help
The value depends on your network needs. ND should normally
be active.
config NET_IPV6_DAD
bool "Activate duplicate address detection"
depends on NET_IPV6_NBR_CACHE
default y
help
The value depends on your network needs. DAD should normally
be active.
config NET_IPV6_RA_RDNSS
bool "Support RA RDNSS option"
depends on NET_IPV6_ND
select DNS_RESOLVER
default y
help
Support Router Advertisement Recursive DNS Server option.
See RFC 6106 for details. The value depends on your network needs.
config NET_6LO
bool "6lowpan IPv6 Compression library"
default y if NET_L2_IEEE802154
help
6lowpan compression and fragmentation. It is enabled by default
if 802.15.4 is present, since using IPv6 on it requires it.
You may disable this option if you wish to implement a non-IP
custom protocol on top of the 802.15.4 MAC (L2) layer.
config NET_6LO_CONTEXT
bool "6lowpan context based compression"
depends on NET_6LO
help
Enables 6lowpan context based compression based on information
received in Router Advertisement (RA) message.
config NET_MAX_6LO_CONTEXTS
int "Number of supported 6CO (6lowpan contexts options)"
depends on NET_6LO_CONTEXT
default 1
range 1 16
help
6lowpan context options table size. The value depends on your
network and memory consumption. More 6CO options uses more memory.
if NET_6LO
module = NET_6LO
module-dep = NET_LOG
module-str = Log level for 6LoWPAN library
module-help = Enables 6LoWPAN code to output debug messages.
source "subsys/net/Kconfig.template.log_config.net"
endif # NET_6LO
module = NET_IPV6
module-dep = NET_LOG
module-str = Log level for core IPv6
module-help = Enables core IPv6 code to output debug messages.
source "subsys/net/Kconfig.template.log_config.net"
module = NET_ICMPV6
module-dep = NET_LOG
module-str = Log level for ICMPv6
module-help = Enables ICMPv6 code to output debug messages.
source "subsys/net/Kconfig.template.log_config.net"
module = NET_IPV6_NBR_CACHE
module-dep = NET_LOG
module-str = Log level for IPv6 neighbor cache
module-help = Enables IPv6 Neighbor Cache code to output debug messages.
source "subsys/net/Kconfig.template.log_config.net"
endif # NET_NATIVE_IPV6
endif # NET_IPV6