blob: 0c537add17a18044f73aaaaaf43da002972fda62 [file] [log] [blame]
/*
* Copyright (c) 2018 Diego Sueiro
*
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT silabs_gecko_i2c
#include <errno.h>
#include <zephyr/drivers/i2c.h>
#include <zephyr/kernel.h>
#include <zephyr/sys/util.h>
#include <em_cmu.h>
#include <em_i2c.h>
#include <em_gpio.h>
#include <soc.h>
#define LOG_LEVEL CONFIG_I2C_LOG_LEVEL
#include <zephyr/logging/log.h>
LOG_MODULE_REGISTER(i2c_gecko);
#include "i2c-priv.h"
#define DEV_BASE(dev) ((I2C_TypeDef *)((const struct i2c_gecko_config *const)(dev)->config)->base)
struct i2c_gecko_config {
I2C_TypeDef *base;
CMU_Clock_TypeDef clock;
uint32_t bitrate;
struct soc_gpio_pin pin_sda;
struct soc_gpio_pin pin_scl;
#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
uint8_t loc_sda;
uint8_t loc_scl;
#else
uint8_t loc;
#endif
#if defined(CONFIG_I2C_TARGET)
void (*irq_config_func)(const struct device *dev);
#endif
};
struct i2c_gecko_data {
struct k_sem device_sync_sem;
uint32_t dev_config;
#if defined(CONFIG_I2C_TARGET)
struct i2c_target_config *target_cfg;
#endif
};
void i2c_gecko_config_pins(const struct device *dev, const struct soc_gpio_pin *pin_sda,
const struct soc_gpio_pin *pin_scl)
{
I2C_TypeDef *base = DEV_BASE(dev);
const struct i2c_gecko_config *config = dev->config;
GPIO_PinModeSet(pin_scl->port, pin_scl->pin, pin_scl->mode, pin_scl->out);
GPIO_PinModeSet(pin_sda->port, pin_sda->pin, pin_sda->mode, pin_sda->out);
#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
base->ROUTEPEN = I2C_ROUTEPEN_SDAPEN | I2C_ROUTEPEN_SCLPEN;
base->ROUTELOC0 = (config->loc_sda << _I2C_ROUTELOC0_SDALOC_SHIFT) |
(config->loc_scl << _I2C_ROUTELOC0_SCLLOC_SHIFT);
#elif defined(GPIO_I2C_ROUTEEN_SCLPEN) && defined(GPIO_I2C_ROUTEEN_SDAPEN)
GPIO->I2CROUTE[I2C_NUM(base)].ROUTEEN = GPIO_I2C_ROUTEEN_SCLPEN | GPIO_I2C_ROUTEEN_SDAPEN;
GPIO->I2CROUTE[I2C_NUM(base)].SCLROUTE =
(config->pin_scl.pin << _GPIO_I2C_SCLROUTE_PIN_SHIFT) |
(config->pin_scl.port << _GPIO_I2C_SCLROUTE_PORT_SHIFT);
GPIO->I2CROUTE[I2C_NUM(base)].SDAROUTE =
(config->pin_sda.pin << _GPIO_I2C_SDAROUTE_PIN_SHIFT) |
(config->pin_sda.port << _GPIO_I2C_SDAROUTE_PORT_SHIFT);
#else
base->ROUTE = I2C_ROUTE_SDAPEN | I2C_ROUTE_SCLPEN | (config->loc << 8);
#endif
}
static int i2c_gecko_configure(const struct device *dev, uint32_t dev_config_raw)
{
I2C_TypeDef *base = DEV_BASE(dev);
struct i2c_gecko_data *data = dev->data;
I2C_Init_TypeDef i2cInit = I2C_INIT_DEFAULT;
uint32_t baudrate;
if (!(I2C_MODE_CONTROLLER & dev_config_raw)) {
return -EINVAL;
}
switch (I2C_SPEED_GET(dev_config_raw)) {
case I2C_SPEED_STANDARD:
baudrate = KHZ(100);
break;
case I2C_SPEED_FAST:
baudrate = KHZ(400);
break;
case I2C_SPEED_FAST_PLUS:
baudrate = MHZ(1);
break;
default:
return -EINVAL;
}
data->dev_config = dev_config_raw;
i2cInit.freq = baudrate;
#if defined(CONFIG_I2C_TARGET)
i2cInit.master = 0;
#endif
I2C_Init(base, &i2cInit);
return 0;
}
static int i2c_gecko_transfer(const struct device *dev, struct i2c_msg *msgs, uint8_t num_msgs,
uint16_t addr)
{
I2C_TypeDef *base = DEV_BASE(dev);
struct i2c_gecko_data *data = dev->data;
I2C_TransferSeq_TypeDef seq;
I2C_TransferReturn_TypeDef ret = -EIO;
uint32_t timeout = 300000U;
if (!num_msgs) {
return 0;
}
seq.addr = addr << 1;
do {
seq.buf[0].data = msgs->buf;
seq.buf[0].len = msgs->len;
if ((msgs->flags & I2C_MSG_RW_MASK) == I2C_MSG_READ) {
seq.flags = I2C_FLAG_READ;
} else {
seq.flags = I2C_FLAG_WRITE;
if (num_msgs > 1) {
/* Next message */
msgs++;
num_msgs--;
if ((msgs->flags & I2C_MSG_RW_MASK) == I2C_MSG_READ) {
seq.flags = I2C_FLAG_WRITE_READ;
} else {
seq.flags = I2C_FLAG_WRITE_WRITE;
}
seq.buf[1].data = msgs->buf;
seq.buf[1].len = msgs->len;
}
}
if (data->dev_config & I2C_ADDR_10_BITS) {
seq.flags |= I2C_FLAG_10BIT_ADDR;
}
/* Do a polled transfer */
ret = I2C_TransferInit(base, &seq);
while (ret == i2cTransferInProgress && timeout--) {
ret = I2C_Transfer(base);
}
if (ret != i2cTransferDone) {
goto finish;
}
/* Next message */
msgs++;
num_msgs--;
} while (num_msgs);
finish:
if (ret != i2cTransferDone) {
ret = -EIO;
}
return ret;
}
static int i2c_gecko_init(const struct device *dev)
{
const struct i2c_gecko_config *config = dev->config;
uint32_t bitrate_cfg;
int error;
CMU_ClockEnable(config->clock, true);
i2c_gecko_config_pins(dev, &config->pin_sda, &config->pin_scl);
bitrate_cfg = i2c_map_dt_bitrate(config->bitrate);
error = i2c_gecko_configure(dev, I2C_MODE_CONTROLLER | bitrate_cfg);
if (error) {
return error;
}
return 0;
}
#if defined(CONFIG_I2C_TARGET)
static int i2c_gecko_target_register(const struct device *dev, struct i2c_target_config *cfg)
{
const struct i2c_gecko_config *config = dev->config;
struct i2c_gecko_data *data = dev->data;
data->target_cfg = cfg;
I2C_SlaveAddressSet(config->base, cfg->address << _I2C_SADDR_ADDR_SHIFT);
/* Match with specified address, no wildcards in address */
I2C_SlaveAddressMaskSet(config->base, _I2C_SADDRMASK_SADDRMASK_MASK);
I2C_IntDisable(config->base, _I2C_IEN_MASK);
I2C_IntEnable(config->base, I2C_IEN_ADDR | I2C_IEN_RXDATAV | I2C_IEN_ACK | I2C_IEN_SSTOP |
I2C_IEN_BUSERR | I2C_IEN_ARBLOST);
config->irq_config_func(dev);
return 0;
}
static int i2c_gecko_target_unregister(const struct device *dev, struct i2c_target_config *cfg)
{
const struct i2c_gecko_config *config = dev->config;
struct i2c_gecko_data *data = dev->data;
data->target_cfg = NULL;
I2C_IntDisable(config->base, _I2C_IEN_MASK);
return 0;
}
#endif
static const struct i2c_driver_api i2c_gecko_driver_api = {
.configure = i2c_gecko_configure,
.transfer = i2c_gecko_transfer,
#if defined(CONFIG_I2C_TARGET)
.target_register = i2c_gecko_target_register,
.target_unregister = i2c_gecko_target_unregister,
#endif
};
#if defined(CONFIG_I2C_TARGET)
void i2c_gecko_isr(const struct device *dev)
{
const struct i2c_gecko_config *config = dev->config;
struct i2c_gecko_data *data = dev->data;
uint32_t pending;
uint32_t rx_byte;
uint8_t tx_byte;
pending = config->base->IF;
/* If some sort of fault, abort transfer. */
if (pending & (I2C_IF_BUSERR | I2C_IF_ARBLOST)) {
LOG_ERR("I2C Bus Error");
I2C_IntClear(config->base, I2C_IF_BUSERR);
I2C_IntClear(config->base, I2C_IF_ARBLOST);
} else {
if (pending & I2C_IF_ADDR) {
/* Address Match, indicating that reception is started */
rx_byte = config->base->RXDATA;
config->base->CMD = I2C_CMD_ACK;
/* Check if read bit set */
if (rx_byte & 0x1) {
data->target_cfg->callbacks->read_requested(data->target_cfg,
&tx_byte);
config->base->TXDATA = tx_byte;
} else {
data->target_cfg->callbacks->write_requested(data->target_cfg);
}
I2C_IntClear(config->base, I2C_IF_ADDR | I2C_IF_RXDATAV);
} else if (pending & I2C_IF_RXDATAV) {
rx_byte = config->base->RXDATA;
/* Read new data and write to target address */
data->target_cfg->callbacks->write_received(data->target_cfg, rx_byte);
config->base->CMD = I2C_CMD_ACK;
I2C_IntClear(config->base, I2C_IF_RXDATAV);
}
if (pending & I2C_IF_ACK) {
/* Leader ACK'ed, so requesting more data */
data->target_cfg->callbacks->read_processed(data->target_cfg, &tx_byte);
config->base->TXDATA = tx_byte;
I2C_IntClear(config->base, I2C_IF_ACK);
}
if (pending & I2C_IF_SSTOP) {
/* End of transaction */
data->target_cfg->callbacks->stop(data->target_cfg);
I2C_IntClear(config->base, I2C_IF_SSTOP);
}
}
}
#endif
#ifdef CONFIG_SOC_GECKO_HAS_INDIVIDUAL_PIN_LOCATION
#define I2C_LOC_DATA(idx) \
.loc_sda = DT_INST_PROP_BY_IDX(idx, location_sda, 0), \
.loc_scl = DT_INST_PROP_BY_IDX(idx, location_scl, 0)
#define I2C_VALIDATE_LOC(idx) BUILD_ASSERT(true, "")
#else
#define I2C_VALIDATE_LOC(idx) \
BUILD_ASSERT(DT_INST_PROP_BY_IDX(idx, location_sda, 0) == \
DT_INST_PROP_BY_IDX(idx, location_scl, 0), \
"DTS location-* properties must be equal")
#define I2C_LOC_DATA(idx) .loc = DT_INST_PROP_BY_IDX(idx, location_scl, 0)
#endif
#if defined(CONFIG_I2C_TARGET)
#define GECKO_I2C_IRQ_DEF(idx) static void i2c_gecko_config_func_##idx(const struct device *dev);
#define GECKO_I2C_IRQ_DATA(idx) .irq_config_func = i2c_gecko_config_func_##idx,
#define GECKO_I2C_IRQ_HANDLER(idx) \
static void i2c_gecko_config_func_##idx(const struct device *dev) \
{ \
IRQ_CONNECT(DT_INST_IRQ(idx, irq), DT_INST_IRQ(idx, priority), i2c_gecko_isr, \
DEVICE_DT_INST_GET(idx), 0); \
irq_enable(DT_INST_IRQ(idx, irq)); \
}
#else
#define GECKO_I2C_IRQ_HANDLER(idx)
#define GECKO_I2C_IRQ_DEF(idx)
#define GECKO_I2C_IRQ_DATA(idx)
#endif
#define I2C_INIT(idx) \
I2C_VALIDATE_LOC(idx); \
GECKO_I2C_IRQ_DEF(idx) \
static const struct i2c_gecko_config i2c_gecko_config_##idx = { \
.base = (I2C_TypeDef *)DT_INST_REG_ADDR(idx), \
.clock = cmuClock_I2C##idx, \
.pin_sda = {DT_INST_PROP_BY_IDX(idx, location_sda, 1), \
DT_INST_PROP_BY_IDX(idx, location_sda, 2), gpioModeWiredAnd, 1}, \
.pin_scl = {DT_INST_PROP_BY_IDX(idx, location_scl, 1), \
DT_INST_PROP_BY_IDX(idx, location_scl, 2), gpioModeWiredAnd, 1}, \
I2C_LOC_DATA(idx), \
.bitrate = DT_INST_PROP(idx, clock_frequency), \
GECKO_I2C_IRQ_DATA(idx)}; \
static struct i2c_gecko_data i2c_gecko_data_##idx; \
I2C_DEVICE_DT_INST_DEFINE(idx, i2c_gecko_init, NULL, &i2c_gecko_data_##idx, \
&i2c_gecko_config_##idx, POST_KERNEL, CONFIG_I2C_INIT_PRIORITY, \
&i2c_gecko_driver_api); \
GECKO_I2C_IRQ_HANDLER(idx)
DT_INST_FOREACH_STATUS_OKAY(I2C_INIT)