|  | /* | 
|  | * Copyright (c) 2017 Piotr Mienkowski | 
|  | * | 
|  | * SPDX-License-Identifier: Apache-2.0 | 
|  | */ | 
|  |  | 
|  | #define DT_DRV_COMPAT atmel_sam_i2c_twihs | 
|  |  | 
|  | /** @file | 
|  | * @brief I2C bus (TWIHS) driver for Atmel SAM MCU family. | 
|  | * | 
|  | * Only I2C Master Mode with 7 bit addressing is currently supported. | 
|  | */ | 
|  |  | 
|  |  | 
|  | #include <errno.h> | 
|  | #include <sys/__assert.h> | 
|  | #include <kernel.h> | 
|  | #include <device.h> | 
|  | #include <init.h> | 
|  | #include <soc.h> | 
|  | #include <drivers/i2c.h> | 
|  |  | 
|  | #define LOG_LEVEL CONFIG_I2C_LOG_LEVEL | 
|  | #include <logging/log.h> | 
|  | LOG_MODULE_REGISTER(i2c_sam_twihs); | 
|  |  | 
|  | #include "i2c-priv.h" | 
|  |  | 
|  | /** I2C bus speed [Hz] in Standard Mode */ | 
|  | #define BUS_SPEED_STANDARD_HZ         100000U | 
|  | /** I2C bus speed [Hz] in Fast Mode */ | 
|  | #define BUS_SPEED_FAST_HZ             400000U | 
|  | /** I2C bus speed [Hz] in High Speed Mode */ | 
|  | #define BUS_SPEED_HIGH_HZ            3400000U | 
|  | /* Maximum value of Clock Divider (CKDIV) */ | 
|  | #define CKDIV_MAX                          7 | 
|  |  | 
|  | /* Device constant configuration parameters */ | 
|  | struct i2c_sam_twihs_dev_cfg { | 
|  | Twihs *regs; | 
|  | void (*irq_config)(void); | 
|  | uint32_t bitrate; | 
|  | const struct soc_gpio_pin *pin_list; | 
|  | uint8_t pin_list_size; | 
|  | uint8_t periph_id; | 
|  | uint8_t irq_id; | 
|  | }; | 
|  |  | 
|  | struct twihs_msg { | 
|  | /* Buffer containing data to read or write */ | 
|  | uint8_t *buf; | 
|  | /* Length of the buffer */ | 
|  | uint32_t len; | 
|  | /* Index of the next byte to be read/written from/to the buffer */ | 
|  | uint32_t idx; | 
|  | /* Value of TWIHS_SR at the end of the message */ | 
|  | uint32_t twihs_sr; | 
|  | /* Transfer flags as defined in the i2c.h file */ | 
|  | uint8_t flags; | 
|  | }; | 
|  |  | 
|  | /* Device run time data */ | 
|  | struct i2c_sam_twihs_dev_data { | 
|  | struct k_sem sem; | 
|  | struct twihs_msg msg; | 
|  | }; | 
|  |  | 
|  | #define DEV_NAME(dev) ((dev)->name) | 
|  | #define DEV_CFG(dev) \ | 
|  | ((const struct i2c_sam_twihs_dev_cfg *const)(dev)->config) | 
|  | #define DEV_DATA(dev) \ | 
|  | ((struct i2c_sam_twihs_dev_data *const)(dev)->data) | 
|  |  | 
|  | static int i2c_clk_set(Twihs *const twihs, uint32_t speed) | 
|  | { | 
|  | uint32_t ck_div = 0U; | 
|  | uint32_t cl_div; | 
|  | bool div_completed = false; | 
|  |  | 
|  | /*  From the datasheet "TWIHS Clock Waveform Generator Register" | 
|  | *  T_low = ( ( CLDIV × 2^CKDIV ) + 3 ) × T_MCK | 
|  | */ | 
|  | while (!div_completed) { | 
|  | cl_div =   ((SOC_ATMEL_SAM_MCK_FREQ_HZ / (speed * 2U)) - 3) | 
|  | / (1 << ck_div); | 
|  |  | 
|  | if (cl_div <= 255U) { | 
|  | div_completed = true; | 
|  | } else { | 
|  | ck_div++; | 
|  | } | 
|  | } | 
|  |  | 
|  | if (ck_div > CKDIV_MAX) { | 
|  | LOG_ERR("Failed to configure I2C clock"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | /* Set I2C bus clock duty cycle to 50% */ | 
|  | twihs->TWIHS_CWGR = TWIHS_CWGR_CLDIV(cl_div) | TWIHS_CWGR_CHDIV(cl_div) | 
|  | | TWIHS_CWGR_CKDIV(ck_div); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int i2c_sam_twihs_configure(const struct device *dev, uint32_t config) | 
|  | { | 
|  | const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev); | 
|  | Twihs *const twihs = dev_cfg->regs; | 
|  | uint32_t bitrate; | 
|  | int ret; | 
|  |  | 
|  | if (!(config & I2C_MODE_MASTER)) { | 
|  | LOG_ERR("Master Mode is not enabled"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | if (config & I2C_ADDR_10_BITS) { | 
|  | LOG_ERR("I2C 10-bit addressing is currently not supported"); | 
|  | LOG_ERR("Please submit a patch"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | /* Configure clock */ | 
|  | switch (I2C_SPEED_GET(config)) { | 
|  | case I2C_SPEED_STANDARD: | 
|  | bitrate = BUS_SPEED_STANDARD_HZ; | 
|  | break; | 
|  | case I2C_SPEED_FAST: | 
|  | bitrate = BUS_SPEED_FAST_HZ; | 
|  | break; | 
|  | default: | 
|  | LOG_ERR("Unsupported I2C speed value"); | 
|  | return -EIO; | 
|  | } | 
|  |  | 
|  | /* Setup clock waveform */ | 
|  | ret = i2c_clk_set(twihs, bitrate); | 
|  | if (ret < 0) { | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* Disable Slave Mode */ | 
|  | twihs->TWIHS_CR = TWIHS_CR_SVDIS; | 
|  |  | 
|  | /* Enable Master Mode */ | 
|  | twihs->TWIHS_CR = TWIHS_CR_MSEN; | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void write_msg_start(Twihs *const twihs, struct twihs_msg *msg, | 
|  | uint8_t daddr) | 
|  | { | 
|  | /* Set slave address. */ | 
|  | twihs->TWIHS_MMR = TWIHS_MMR_DADR(daddr); | 
|  |  | 
|  | /* Write first data byte on I2C bus */ | 
|  | twihs->TWIHS_THR = msg->buf[msg->idx++]; | 
|  |  | 
|  | /* Enable Transmit Ready and Transmission Completed interrupts */ | 
|  | twihs->TWIHS_IER = TWIHS_IER_TXRDY | TWIHS_IER_TXCOMP | TWIHS_IER_NACK; | 
|  | } | 
|  |  | 
|  | static void read_msg_start(Twihs *const twihs, struct twihs_msg *msg, | 
|  | uint8_t daddr) | 
|  | { | 
|  | uint32_t twihs_cr_stop; | 
|  |  | 
|  | /* Set slave address and number of internal address bytes */ | 
|  | twihs->TWIHS_MMR = TWIHS_MMR_MREAD | TWIHS_MMR_DADR(daddr); | 
|  |  | 
|  | /* Enable Receive Ready and Transmission Completed interrupts */ | 
|  | twihs->TWIHS_IER = TWIHS_IER_RXRDY | TWIHS_IER_TXCOMP | TWIHS_IER_NACK; | 
|  |  | 
|  | /* In single data byte read the START and STOP must both be set */ | 
|  | twihs_cr_stop = (msg->len == 1U) ? TWIHS_CR_STOP : 0; | 
|  | /* Start the transfer by sending START condition */ | 
|  | twihs->TWIHS_CR = TWIHS_CR_START | twihs_cr_stop; | 
|  | } | 
|  |  | 
|  | static int i2c_sam_twihs_transfer(const struct device *dev, | 
|  | struct i2c_msg *msgs, | 
|  | uint8_t num_msgs, uint16_t addr) | 
|  | { | 
|  | const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev); | 
|  | struct i2c_sam_twihs_dev_data *const dev_data = DEV_DATA(dev); | 
|  | Twihs *const twihs = dev_cfg->regs; | 
|  |  | 
|  | __ASSERT_NO_MSG(msgs); | 
|  | if (!num_msgs) { | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | /* Clear pending interrupts, such as NACK. */ | 
|  | (void)twihs->TWIHS_SR; | 
|  |  | 
|  | /* Set number of internal address bytes to 0, not used. */ | 
|  | twihs->TWIHS_IADR = 0; | 
|  |  | 
|  | for (int i = 0; i < num_msgs; i++) { | 
|  | dev_data->msg.buf = msgs[i].buf; | 
|  | dev_data->msg.len = msgs[i].len; | 
|  | dev_data->msg.idx = 0U; | 
|  | dev_data->msg.twihs_sr = 0U; | 
|  | dev_data->msg.flags = msgs[i].flags; | 
|  | if ((msgs[i].flags & I2C_MSG_RW_MASK) == I2C_MSG_READ) { | 
|  | read_msg_start(twihs, &dev_data->msg, addr); | 
|  | } else { | 
|  | write_msg_start(twihs, &dev_data->msg, addr); | 
|  | } | 
|  | /* Wait for the transfer to complete */ | 
|  | k_sem_take(&dev_data->sem, K_FOREVER); | 
|  |  | 
|  | if (dev_data->msg.twihs_sr > 0) { | 
|  | /* Something went wrong */ | 
|  | return -EIO; | 
|  | } | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void i2c_sam_twihs_isr(const struct device *dev) | 
|  | { | 
|  | const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev); | 
|  | struct i2c_sam_twihs_dev_data *const dev_data = DEV_DATA(dev); | 
|  | Twihs *const twihs = dev_cfg->regs; | 
|  | struct twihs_msg *msg = &dev_data->msg; | 
|  | uint32_t isr_status; | 
|  |  | 
|  | /* Retrieve interrupt status */ | 
|  | isr_status = twihs->TWIHS_SR & twihs->TWIHS_IMR; | 
|  |  | 
|  | /* Not Acknowledged */ | 
|  | if (isr_status & TWIHS_SR_NACK) { | 
|  | msg->twihs_sr = isr_status; | 
|  | goto tx_comp; | 
|  | } | 
|  |  | 
|  | /* Byte received */ | 
|  | if (isr_status & TWIHS_SR_RXRDY) { | 
|  |  | 
|  | msg->buf[msg->idx++] = twihs->TWIHS_RHR; | 
|  |  | 
|  | if (msg->idx == msg->len - 1U) { | 
|  | /* Send STOP condition */ | 
|  | twihs->TWIHS_CR = TWIHS_CR_STOP; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* Byte sent */ | 
|  | if (isr_status & TWIHS_SR_TXRDY) { | 
|  | if (msg->idx == msg->len) { | 
|  | if (msg->flags & I2C_MSG_STOP) { | 
|  | /* Send STOP condition */ | 
|  | twihs->TWIHS_CR = TWIHS_CR_STOP; | 
|  | /* Disable Transmit Ready interrupt */ | 
|  | twihs->TWIHS_IDR = TWIHS_IDR_TXRDY; | 
|  | } else { | 
|  | /* Transmission completed */ | 
|  | goto tx_comp; | 
|  | } | 
|  | } else { | 
|  | twihs->TWIHS_THR = msg->buf[msg->idx++]; | 
|  | } | 
|  | } | 
|  |  | 
|  | /* Transmission completed */ | 
|  | if (isr_status & TWIHS_SR_TXCOMP) { | 
|  | goto tx_comp; | 
|  | } | 
|  |  | 
|  | return; | 
|  |  | 
|  | tx_comp: | 
|  | /* Disable all enabled interrupts */ | 
|  | twihs->TWIHS_IDR = twihs->TWIHS_IMR; | 
|  | /* We are done */ | 
|  | k_sem_give(&dev_data->sem); | 
|  | } | 
|  |  | 
|  | static int i2c_sam_twihs_initialize(const struct device *dev) | 
|  | { | 
|  | const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev); | 
|  | struct i2c_sam_twihs_dev_data *const dev_data = DEV_DATA(dev); | 
|  | Twihs *const twihs = dev_cfg->regs; | 
|  | uint32_t bitrate_cfg; | 
|  | int ret; | 
|  |  | 
|  | /* Configure interrupts */ | 
|  | dev_cfg->irq_config(); | 
|  |  | 
|  | /* Initialize semaphore */ | 
|  | k_sem_init(&dev_data->sem, 0, 1); | 
|  |  | 
|  | /* Connect pins to the peripheral */ | 
|  | soc_gpio_list_configure(dev_cfg->pin_list, dev_cfg->pin_list_size); | 
|  |  | 
|  | /* Enable module's clock */ | 
|  | soc_pmc_peripheral_enable(dev_cfg->periph_id); | 
|  |  | 
|  | /* Reset the module */ | 
|  | twihs->TWIHS_CR = TWIHS_CR_SWRST; | 
|  |  | 
|  | bitrate_cfg = i2c_map_dt_bitrate(dev_cfg->bitrate); | 
|  |  | 
|  | ret = i2c_sam_twihs_configure(dev, I2C_MODE_MASTER | bitrate_cfg); | 
|  | if (ret < 0) { | 
|  | LOG_ERR("Failed to initialize %s device", DEV_NAME(dev)); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | /* Enable module's IRQ */ | 
|  | irq_enable(dev_cfg->irq_id); | 
|  |  | 
|  | LOG_INF("Device %s initialized", DEV_NAME(dev)); | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static const struct i2c_driver_api i2c_sam_twihs_driver_api = { | 
|  | .configure = i2c_sam_twihs_configure, | 
|  | .transfer = i2c_sam_twihs_transfer, | 
|  | }; | 
|  |  | 
|  | #define I2C_TWIHS_SAM_INIT(n)						\ | 
|  | DEVICE_DECLARE(i2c##n##_sam);		\ | 
|  | \ | 
|  | static void i2c##n##_sam_irq_config(void)			\ | 
|  | {								\ | 
|  | IRQ_CONNECT(DT_INST_IRQN(n), DT_INST_IRQ(n, priority),	\ | 
|  | i2c_sam_twihs_isr,				\ | 
|  | DEVICE_GET(i2c##n##_sam), 0);		\ | 
|  | }								\ | 
|  | \ | 
|  | static const struct soc_gpio_pin pins_twihs##n[] =		\ | 
|  | {ATMEL_SAM_DT_PIN(n, 0), ATMEL_SAM_DT_PIN(n, 1)};	\ | 
|  | \ | 
|  | static const struct i2c_sam_twihs_dev_cfg i2c##n##_sam_config = {\ | 
|  | .regs = (Twihs *)DT_INST_REG_ADDR(n),			\ | 
|  | .irq_config = i2c##n##_sam_irq_config,			\ | 
|  | .periph_id = DT_INST_PROP(n, peripheral_id),		\ | 
|  | .irq_id = DT_INST_IRQN(n),				\ | 
|  | .pin_list = pins_twihs##n,				\ | 
|  | .pin_list_size = ARRAY_SIZE(pins_twihs##n),		\ | 
|  | .bitrate = DT_INST_PROP(n, clock_frequency),		\ | 
|  | };								\ | 
|  | \ | 
|  | static struct i2c_sam_twihs_dev_data i2c##n##_sam_data;		\ | 
|  | \ | 
|  | DEVICE_AND_API_INIT(i2c##n##_sam, DT_INST_LABEL(n),		\ | 
|  | &i2c_sam_twihs_initialize,			\ | 
|  | &i2c##n##_sam_data, &i2c##n##_sam_config,	\ | 
|  | POST_KERNEL, CONFIG_I2C_INIT_PRIORITY,	\ | 
|  | &i2c_sam_twihs_driver_api); | 
|  |  | 
|  | DT_INST_FOREACH_STATUS_OKAY(I2C_TWIHS_SAM_INIT) |