/** | |
****************************************************************************** | |
* @file stm32f4xx_hal_cryp.c | |
* @author MCD Application Team | |
* @brief CRYP HAL module driver. | |
* This file provides firmware functions to manage the following | |
* functionalities of the Cryptography (CRYP) peripheral: | |
* + Initialization and de-initialization functions | |
* + AES processing functions | |
* + DES processing functions | |
* + TDES processing functions | |
* + DMA callback functions | |
* + CRYP IRQ handler management | |
* + Peripheral State functions | |
* | |
@verbatim | |
============================================================================== | |
##### How to use this driver ##### | |
============================================================================== | |
[..] | |
The CRYP HAL driver can be used as follows: | |
(#)Initialize the CRYP low level resources by implementing the HAL_CRYP_MspInit(): | |
(##) Enable the CRYP interface clock using __HAL_RCC_CRYP_CLK_ENABLE() | |
(##) In case of using interrupts (e.g. HAL_CRYP_AESECB_Encrypt_IT()) | |
(+++) Configure the CRYP interrupt priority using HAL_NVIC_SetPriority() | |
(+++) Enable the CRYP IRQ handler using HAL_NVIC_EnableIRQ() | |
(+++) In CRYP IRQ handler, call HAL_CRYP_IRQHandler() | |
(##) In case of using DMA to control data transfer (e.g. HAL_CRYP_AESECB_Encrypt_DMA()) | |
(+++) Enable the DMAx interface clock using __DMAx_CLK_ENABLE() | |
(+++) Configure and enable two DMA streams one for managing data transfer from | |
memory to peripheral (input stream) and another stream for managing data | |
transfer from peripheral to memory (output stream) | |
(+++) Associate the initialized DMA handle to the CRYP DMA handle | |
using __HAL_LINKDMA() | |
(+++) Configure the priority and enable the NVIC for the transfer complete | |
interrupt on the two DMA Streams. The output stream should have higher | |
priority than the input stream HAL_NVIC_SetPriority() and HAL_NVIC_EnableIRQ() | |
(#)Initialize the CRYP HAL using HAL_CRYP_Init(). This function configures mainly: | |
(##) The data type: 1-bit, 8-bit, 16-bit and 32-bit | |
(##) The key size: 128, 192 and 256. This parameter is relevant only for AES | |
(##) The encryption/decryption key. It's size depends on the algorithm | |
used for encryption/decryption | |
(##) The initialization vector (counter). It is not used ECB mode. | |
(#)Three processing (encryption/decryption) functions are available: | |
(##) Polling mode: encryption and decryption APIs are blocking functions | |
i.e. they process the data and wait till the processing is finished, | |
e.g. HAL_CRYP_AESCBC_Encrypt() | |
(##) Interrupt mode: encryption and decryption APIs are not blocking functions | |
i.e. they process the data under interrupt, | |
e.g. HAL_CRYP_AESCBC_Encrypt_IT() | |
(##) DMA mode: encryption and decryption APIs are not blocking functions | |
i.e. the data transfer is ensured by DMA, | |
e.g. HAL_CRYP_AESCBC_Encrypt_DMA() | |
(#)When the processing function is called at first time after HAL_CRYP_Init() | |
the CRYP peripheral is initialized and processes the buffer in input. | |
At second call, the processing function performs an append of the already | |
processed buffer. | |
When a new data block is to be processed, call HAL_CRYP_Init() then the | |
processing function. | |
(#)Call HAL_CRYP_DeInit() to deinitialize the CRYP peripheral. | |
@endverbatim | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "stm32f4xx_hal.h" | |
/** @addtogroup STM32F4xx_HAL_Driver | |
* @{ | |
*/ | |
#ifdef HAL_CRYP_MODULE_ENABLED | |
#if defined(CRYP) | |
/** @defgroup CRYP CRYP | |
* @brief CRYP HAL module driver. | |
* @{ | |
*/ | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/** @addtogroup CRYP_Private_define | |
* @{ | |
*/ | |
#define CRYP_TIMEOUT_VALUE 1U | |
/** | |
* @} | |
*/ | |
/* Private macro -------------------------------------------------------------*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/** @addtogroup CRYP_Private_Functions_prototypes | |
* @{ | |
*/ | |
static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize); | |
static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize); | |
static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout); | |
static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout); | |
static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma); | |
static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma); | |
static void CRYP_DMAError(DMA_HandleTypeDef *hdma); | |
static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr); | |
static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); | |
static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); | |
static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); | |
static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction); | |
/** | |
* @} | |
*/ | |
/* Private functions ---------------------------------------------------------*/ | |
/** @addtogroup CRYP_Private_Functions | |
* @{ | |
*/ | |
/** | |
* @brief DMA CRYP Input Data process complete callback. | |
* @param hdma DMA handle | |
* @retval None | |
*/ | |
static void CRYP_DMAInCplt(DMA_HandleTypeDef *hdma) | |
{ | |
CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; | |
/* Disable the DMA transfer for input FIFO request by resetting the DIEN bit | |
in the DMACR register */ | |
hcryp->Instance->DMACR &= (uint32_t)(~CRYP_DMACR_DIEN); | |
/* Call input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
/** | |
* @brief DMA CRYP Output Data process complete callback. | |
* @param hdma DMA handle | |
* @retval None | |
*/ | |
static void CRYP_DMAOutCplt(DMA_HandleTypeDef *hdma) | |
{ | |
CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; | |
/* Disable the DMA transfer for output FIFO request by resetting the DOEN bit | |
in the DMACR register */ | |
hcryp->Instance->DMACR &= (uint32_t)(~CRYP_DMACR_DOEN); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Change the CRYP state to ready */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call output data transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
/** | |
* @brief DMA CRYP communication error callback. | |
* @param hdma DMA handle | |
* @retval None | |
*/ | |
static void CRYP_DMAError(DMA_HandleTypeDef *hdma) | |
{ | |
CRYP_HandleTypeDef* hcryp = (CRYP_HandleTypeDef*)((DMA_HandleTypeDef*)hdma)->Parent; | |
hcryp->State= HAL_CRYP_STATE_READY; | |
HAL_CRYP_ErrorCallback(hcryp); | |
} | |
/** | |
* @brief Writes the Key in Key registers. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Key Pointer to Key buffer | |
* @param KeySize Size of Key | |
* @retval None | |
*/ | |
static void CRYP_SetKey(CRYP_HandleTypeDef *hcryp, uint8_t *Key, uint32_t KeySize) | |
{ | |
uint32_t keyaddr = (uint32_t)Key; | |
switch(KeySize) | |
{ | |
case CRYP_KEYSIZE_256B: | |
/* Key Initialisation */ | |
hcryp->Instance->K0LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K0RR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K1LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K1RR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr)); | |
break; | |
case CRYP_KEYSIZE_192B: | |
hcryp->Instance->K1LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K1RR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr)); | |
break; | |
case CRYP_KEYSIZE_128B: | |
hcryp->Instance->K2LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K2RR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K3LR = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->K3RR = __REV(*(uint32_t*)(keyaddr)); | |
break; | |
default: | |
break; | |
} | |
} | |
/** | |
* @brief Writes the InitVector/InitCounter in IV registers. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param InitVector Pointer to InitVector/InitCounter buffer | |
* @param IVSize Size of the InitVector/InitCounter | |
* @retval None | |
*/ | |
static void CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp, uint8_t *InitVector, uint32_t IVSize) | |
{ | |
uint32_t ivaddr = (uint32_t)InitVector; | |
switch(IVSize) | |
{ | |
case CRYP_KEYSIZE_128B: | |
hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IV1LR = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IV1RR = __REV(*(uint32_t*)(ivaddr)); | |
break; | |
/* Whatever key size 192 or 256, Init vector is written in IV0LR and IV0RR */ | |
case CRYP_KEYSIZE_192B: | |
hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr)); | |
break; | |
case CRYP_KEYSIZE_256B: | |
hcryp->Instance->IV0LR = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IV0RR = __REV(*(uint32_t*)(ivaddr)); | |
break; | |
default: | |
break; | |
} | |
} | |
/** | |
* @brief Process Data: Writes Input data in polling mode and read the output data | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Input Pointer to the Input buffer | |
* @param Ilength Length of the Input buffer, must be a multiple of 16. | |
* @param Output Pointer to the returned buffer | |
* @param Timeout Timeout value | |
* @retval None | |
*/ | |
static HAL_StatusTypeDef CRYP_ProcessData(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0U; | |
uint32_t i = 0U; | |
uint32_t inputaddr = (uint32_t)Input; | |
uint32_t outputaddr = (uint32_t)Output; | |
for(i=0U; (i < Ilength); i+=16U) | |
{ | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_CLR(hcryp->Instance->SR, CRYP_FLAG_OFNE)) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout)) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Process Data: Write Input data in polling mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Input Pointer to the Input buffer | |
* @param Ilength Length of the Input buffer, must be a multiple of 8 | |
* @param Output Pointer to the returned buffer | |
* @param Timeout Specify Timeout value | |
* @retval None | |
*/ | |
static HAL_StatusTypeDef CRYP_ProcessData2Words(CRYP_HandleTypeDef *hcryp, uint8_t* Input, uint16_t Ilength, uint8_t* Output, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0U; | |
uint32_t i = 0U; | |
uint32_t inputaddr = (uint32_t)Input; | |
uint32_t outputaddr = (uint32_t)Output; | |
for(i=0U; (i < Ilength); i+=8U) | |
{ | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_CLR(hcryp->Instance->SR, CRYP_FLAG_OFNE)) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout)) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Set the DMA configuration and start the DMA transfer | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param inputaddr address of the Input buffer | |
* @param Size Size of the Input buffer, must be a multiple of 16. | |
* @param outputaddr address of the Output buffer | |
* @retval None | |
*/ | |
static void CRYP_SetDMAConfig(CRYP_HandleTypeDef *hcryp, uint32_t inputaddr, uint16_t Size, uint32_t outputaddr) | |
{ | |
/* Set the CRYP DMA transfer complete callback */ | |
hcryp->hdmain->XferCpltCallback = CRYP_DMAInCplt; | |
/* Set the DMA error callback */ | |
hcryp->hdmain->XferErrorCallback = CRYP_DMAError; | |
/* Set the CRYP DMA transfer complete callback */ | |
hcryp->hdmaout->XferCpltCallback = CRYP_DMAOutCplt; | |
/* Set the DMA error callback */ | |
hcryp->hdmaout->XferErrorCallback = CRYP_DMAError; | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Enable the DMA In DMA Stream */ | |
HAL_DMA_Start_IT(hcryp->hdmain, inputaddr, (uint32_t)&hcryp->Instance->DR, Size/4U); | |
/* Enable In DMA request */ | |
hcryp->Instance->DMACR = (CRYP_DMACR_DIEN); | |
/* Enable the DMA Out DMA Stream */ | |
HAL_DMA_Start_IT(hcryp->hdmaout, (uint32_t)&hcryp->Instance->DOUT, outputaddr, Size/4U); | |
/* Enable Out DMA request */ | |
hcryp->Instance->DMACR |= CRYP_DMACR_DOEN; | |
} | |
/** | |
* @brief Sets the CRYP peripheral in DES ECB mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Direction Encryption or decryption | |
* @retval None | |
*/ | |
static void CRYP_SetDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) | |
{ | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_DES_ECB | Direction); | |
/* Set the key */ | |
hcryp->Instance->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey)); | |
hcryp->Instance->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4U)); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
} | |
/** | |
* @brief Sets the CRYP peripheral in DES CBC mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Direction Encryption or decryption | |
* @retval None | |
*/ | |
static void CRYP_SetDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) | |
{ | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_DES_CBC | Direction); | |
/* Set the key */ | |
hcryp->Instance->K1LR = __REV(*(uint32_t*)(hcryp->Init.pKey)); | |
hcryp->Instance->K1RR = __REV(*(uint32_t*)(hcryp->Init.pKey+4U)); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
} | |
/** | |
* @brief Sets the CRYP peripheral in TDES ECB mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Direction Encryption or decryption | |
* @retval None | |
*/ | |
static void CRYP_SetTDESECBMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) | |
{ | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_TDES_ECB | Direction); | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
} | |
/** | |
* @brief Sets the CRYP peripheral in TDES CBC mode | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param Direction Encryption or decryption | |
* @retval None | |
*/ | |
static void CRYP_SetTDESCBCMode(CRYP_HandleTypeDef *hcryp, uint32_t Direction) | |
{ | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the CRYP peripheral in AES CBC mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_TDES_CBC | Direction); | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, CRYP_KEYSIZE_192B); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_256B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/* Exported functions --------------------------------------------------------*/ | |
/** @addtogroup CRYP_Exported_Functions | |
* @{ | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group1 Initialization and de-initialization functions | |
* @brief Initialization and Configuration functions. | |
* | |
@verbatim | |
============================================================================== | |
##### Initialization and de-initialization functions ##### | |
============================================================================== | |
[..] This section provides functions allowing to: | |
(+) Initialize the CRYP according to the specified parameters | |
in the CRYP_InitTypeDef and creates the associated handle | |
(+) DeInitialize the CRYP peripheral | |
(+) Initialize the CRYP MSP | |
(+) DeInitialize CRYP MSP | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initializes the CRYP according to the specified | |
* parameters in the CRYP_InitTypeDef and creates the associated handle. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Check the CRYP handle allocation */ | |
if(hcryp == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check the parameters */ | |
assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize)); | |
assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType)); | |
if(hcryp->State == HAL_CRYP_STATE_RESET) | |
{ | |
/* Allocate lock resource and initialize it */ | |
hcryp->Lock = HAL_UNLOCKED; | |
/* Init the low level hardware */ | |
HAL_CRYP_MspInit(hcryp); | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set the key size and data type*/ | |
CRYP->CR = (uint32_t) (hcryp->Init.KeySize | hcryp->Init.DataType); | |
/* Reset CrypInCount and CrypOutCount */ | |
hcryp->CrypInCount = 0U; | |
hcryp->CrypOutCount = 0U; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Set the default CRYP phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_READY; | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief DeInitializes the CRYP peripheral. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Check the CRYP handle allocation */ | |
if(hcryp == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set the default CRYP phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_READY; | |
/* Reset CrypInCount and CrypOutCount */ | |
hcryp->CrypInCount = 0U; | |
hcryp->CrypOutCount = 0U; | |
/* Disable the CRYP Peripheral Clock */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* DeInit the low level hardware: CLOCK, NVIC.*/ | |
HAL_CRYP_MspDeInit(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_RESET; | |
/* Release Lock */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP MSP. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_CRYP_MspInit could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief DeInitializes CRYP MSP. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_CRYP_MspDeInit could be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group2 AES processing functions | |
* @brief processing functions. | |
* | |
@verbatim | |
============================================================================== | |
##### AES processing functions ##### | |
============================================================================== | |
[..] This section provides functions allowing to: | |
(+) Encrypt plaintext using AES-128/192/256 using chaining modes | |
(+) Decrypt cyphertext using AES-128/192/256 using chaining modes | |
[..] Three processing functions are available: | |
(+) Polling mode | |
(+) Interrupt mode | |
(+) DMA mode | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB encryption mode | |
* then encrypt pPlainData. The cypher data are available in pCypherData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CBC encryption mode | |
* then encrypt pPlainData. The cypher data are available in pCypherData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData(hcryp,pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CTR encryption mode | |
* then encrypt pPlainData. The cypher data are available in pCypherData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB decryption mode | |
* then decrypted pCypherData. The cypher data are available in pPlainData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0U; | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES Key mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout)) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Reset the ALGOMODE bits*/ | |
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); | |
/* Set the CRYP peripheral in AES ECB decryption mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB decryption mode | |
* then decrypted pCypherData. The cypher data are available in pPlainData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
uint32_t tickstart = 0U; | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES Key mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0U)||((HAL_GetTick() - tickstart ) > Timeout)) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
/* Reset the ALGOMODE bits*/ | |
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); | |
/* Set the CRYP peripheral in AES CBC decryption mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CTR decryption mode | |
* then decrypted pCypherData. The cypher data are available in pPlainData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES CTR mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB encryption mode using Interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 bytes | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Process Locked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CBC encryption mode using Interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 bytes | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES CBC mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Process Locked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CTR encryption mode using Interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 bytes | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES CTR mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB decryption mode using Interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t tickstart = 0U; | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES Key mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) | |
{ | |
/* Check for the Timeout */ | |
if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Reset the ALGOMODE bits*/ | |
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); | |
/* Set the CRYP peripheral in AES ECB decryption mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CBC decryption mode using IT. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t tickstart = 0U; | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Get the buffer addresses and sizes */ | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES Key mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) | |
{ | |
/* Check for the Timeout */ | |
if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Reset the ALGOMODE bits*/ | |
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); | |
/* Set the CRYP peripheral in AES CBC decryption mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CTR decryption mode using Interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Get the buffer addresses and sizes */ | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES CTR mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 bytes | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CTR encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES ECB mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES ECB decryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 bytes | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t tickstart = 0U; | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES Key mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) | |
{ | |
/* Check for the Timeout */ | |
if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Reset the ALGOMODE bits*/ | |
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); | |
/* Set the CRYP peripheral in AES ECB decryption mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_ECB | CRYP_CR_ALGODIR); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CBC encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 bytes | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t tickstart = 0U; | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES Key mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_KEY | CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Get tick */ | |
tickstart = HAL_GetTick(); | |
while(HAL_IS_BIT_SET(hcryp->Instance->SR, CRYP_FLAG_BUSY)) | |
{ | |
/* Check for the Timeout */ | |
if((HAL_GetTick() - tickstart ) > CRYP_TIMEOUT_VALUE) | |
{ | |
/* Change state */ | |
hcryp->State = HAL_CRYP_STATE_TIMEOUT; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Reset the ALGOMODE bits*/ | |
CRYP->CR &= (uint32_t)(~CRYP_CR_ALGOMODE); | |
/* Set the CRYP peripheral in AES CBC decryption mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CBC | CRYP_CR_ALGODIR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in AES CTR decryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Check if initialization phase has already been performed */ | |
if(hcryp->Phase == HAL_CRYP_PHASE_READY) | |
{ | |
/* Set the key */ | |
CRYP_SetKey(hcryp, hcryp->Init.pKey, hcryp->Init.KeySize); | |
/* Set the CRYP peripheral in AES CTR mode */ | |
__HAL_CRYP_SET_MODE(hcryp, CRYP_CR_ALGOMODE_AES_CTR | CRYP_CR_ALGODIR); | |
/* Set the Initialization Vector */ | |
CRYP_SetInitVector(hcryp, hcryp->Init.pInitVect, CRYP_KEYSIZE_128B); | |
/* Flush FIFO */ | |
__HAL_CRYP_FIFO_FLUSH(hcryp); | |
/* Set the phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_PROCESS; | |
} | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group3 DES processing functions | |
* @brief processing functions. | |
* | |
@verbatim | |
============================================================================== | |
##### DES processing functions ##### | |
============================================================================== | |
[..] This section provides functions allowing to: | |
(+) Encrypt plaintext using DES using ECB or CBC chaining modes | |
(+) Decrypt cyphertext using ECB or CBC chaining modes | |
[..] Three processing functions are available: | |
(+) Polling mode | |
(+) Interrupt mode | |
(+) DMA mode | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB encryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES ECB encryption mode */ | |
CRYP_SetDESECBMode(hcryp, 0U); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB decryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES ECB decryption mode */ | |
CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES CBC encryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES CBC encryption mode */ | |
CRYP_SetDESCBCMode(hcryp, 0U); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB decryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES CBC decryption mode */ | |
CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB encryption mode using IT. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES ECB encryption mode */ | |
CRYP_SetDESECBMode(hcryp, 0U); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
/* Disable IT */ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES CBC encryption mode using interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES CBC encryption mode */ | |
CRYP_SetDESCBCMode(hcryp, 0U); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
/* Disable IT */ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using IT. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES ECB decryption mode */ | |
CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
/* Disable IT */ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES CBC decryption mode */ | |
CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
/* Disable IT */ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES ECB encryption mode */ | |
CRYP_SetDESECBMode(hcryp, 0U); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES CBC encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES CBC encryption mode */ | |
CRYP_SetDESCBCMode(hcryp, 0U); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES ECB decryption mode */ | |
CRYP_SetDESECBMode(hcryp, CRYP_CR_ALGODIR); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in DES ECB decryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in DES CBC decryption mode */ | |
CRYP_SetDESCBCMode(hcryp, CRYP_CR_ALGODIR); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group4 TDES processing functions | |
* @brief processing functions. | |
* | |
@verbatim | |
============================================================================== | |
##### TDES processing functions ##### | |
============================================================================== | |
[..] This section provides functions allowing to: | |
(+) Encrypt plaintext using TDES based on ECB or CBC chaining modes | |
(+) Decrypt cyphertext using TDES based on ECB or CBC chaining modes | |
[..] Three processing functions are available: | |
(+) Polling mode | |
(+) Interrupt mode | |
(+) DMA mode | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initializes the CRYP peripheral in TDES ECB encryption mode | |
* then encrypt pPlainData. The cypher data are available in pCypherData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES ECB encryption mode */ | |
CRYP_SetTDESECBMode(hcryp, 0U); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES ECB decryption mode | |
* then decrypted pCypherData. The cypher data are available in pPlainData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES ECB decryption mode */ | |
CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Cypher Data and Get Plain Data */ | |
if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES CBC encryption mode | |
* then encrypt pPlainData. The cypher data are available in pCypherData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES CBC encryption mode */ | |
CRYP_SetTDESCBCMode(hcryp, 0U); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Plain Data and Get Cypher Data */ | |
if(CRYP_ProcessData2Words(hcryp, pPlainData, Size, pCypherData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES CBC decryption mode | |
* then decrypted pCypherData. The cypher data are available in pPlainData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES CBC decryption mode */ | |
CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Write Cypher Data and Get Plain Data */ | |
if(CRYP_ProcessData2Words(hcryp, pCypherData, Size, pPlainData, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES ECB encryption mode using interrupt. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES ECB encryption mode */ | |
CRYP_SetTDESECBMode(hcryp, 0U); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
/* Disable IT */ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call the Output data transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES CBC encryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pPlainData; | |
hcryp->pCrypOutBuffPtr = pCypherData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES CBC encryption mode */ | |
CRYP_SetTDESCBCMode(hcryp, 0U); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES ECB decryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES ECB decryption mode */ | |
CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES CBC decryption mode. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if(hcryp->State == HAL_CRYP_STATE_READY) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
hcryp->CrypInCount = Size; | |
hcryp->pCrypInBuffPtr = pCypherData; | |
hcryp->pCrypOutBuffPtr = pPlainData; | |
hcryp->CrypOutCount = Size; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES CBC decryption mode */ | |
CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR); | |
/* Enable Interrupts */ | |
__HAL_CRYP_ENABLE_IT(hcryp, CRYP_IT_INI | CRYP_IT_OUTI); | |
/* Enable CRYP */ | |
__HAL_CRYP_ENABLE(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_INI)) | |
{ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Write the Input block in the IN FIFO */ | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DR = *(uint32_t*)(inputaddr); | |
hcryp->pCrypInBuffPtr += 8U; | |
hcryp->CrypInCount -= 8U; | |
if(hcryp->CrypInCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_INI); | |
/* Call the Input data transfer complete callback */ | |
HAL_CRYP_InCpltCallback(hcryp); | |
} | |
} | |
else if(__HAL_CRYP_GET_IT(hcryp, CRYP_IT_OUTI)) | |
{ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the Output block from the Output FIFO */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUT; | |
hcryp->pCrypOutBuffPtr += 8U; | |
hcryp->CrypOutCount -= 8U; | |
if(hcryp->CrypOutCount == 0U) | |
{ | |
__HAL_CRYP_DISABLE_IT(hcryp, CRYP_IT_OUTI); | |
/* Disable CRYP */ | |
__HAL_CRYP_DISABLE(hcryp); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Call Input transfer complete callback */ | |
HAL_CRYP_OutCpltCallback(hcryp); | |
} | |
} | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES ECB encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES ECB encryption mode */ | |
CRYP_SetTDESECBMode(hcryp, 0U); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES CBC encryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pPlainData; | |
outputaddr = (uint32_t)pCypherData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES CBC encryption mode */ | |
CRYP_SetTDESCBCMode(hcryp, 0U); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES ECB decryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES ECB decryption mode */ | |
CRYP_SetTDESECBMode(hcryp, CRYP_CR_ALGODIR); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @brief Initializes the CRYP peripheral in TDES CBC decryption mode using DMA. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 8 | |
* @param pPlainData Pointer to the plaintext buffer | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_TDESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
uint32_t inputaddr; | |
uint32_t outputaddr; | |
if((hcryp->State == HAL_CRYP_STATE_READY) || (hcryp->Phase == HAL_CRYP_PHASE_PROCESS)) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(hcryp); | |
inputaddr = (uint32_t)pCypherData; | |
outputaddr = (uint32_t)pPlainData; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set CRYP peripheral in TDES CBC decryption mode */ | |
CRYP_SetTDESCBCMode(hcryp, CRYP_CR_ALGODIR); | |
/* Set the input and output addresses and start DMA transfer */ | |
CRYP_SetDMAConfig(hcryp, inputaddr, Size, outputaddr); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group5 DMA callback functions | |
* @brief DMA callback functions. | |
* | |
@verbatim | |
============================================================================== | |
##### DMA callback functions ##### | |
============================================================================== | |
[..] This section provides DMA callback functions: | |
(+) DMA Input data transfer complete | |
(+) DMA Output data transfer complete | |
(+) DMA error | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Input FIFO transfer completed callbacks. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_CRYP_InCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Output FIFO transfer completed callbacks. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_CRYP_OutCpltCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief CRYP error callbacks. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_CRYP_ErrorCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group6 CRYP IRQ handler management | |
* @brief CRYP IRQ handler. | |
* | |
@verbatim | |
============================================================================== | |
##### CRYP IRQ handler management ##### | |
============================================================================== | |
[..] This section provides CRYP IRQ handler function. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief This function handles CRYP interrupt request. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp) | |
{ | |
switch(CRYP->CR & CRYP_CR_ALGOMODE_DIRECTION) | |
{ | |
case CRYP_CR_ALGOMODE_TDES_ECB_ENCRYPT: | |
HAL_CRYP_TDESECB_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_TDES_ECB_DECRYPT: | |
HAL_CRYP_TDESECB_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_TDES_CBC_ENCRYPT: | |
HAL_CRYP_TDESCBC_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_TDES_CBC_DECRYPT: | |
HAL_CRYP_TDESCBC_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_DES_ECB_ENCRYPT: | |
HAL_CRYP_DESECB_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_DES_ECB_DECRYPT: | |
HAL_CRYP_DESECB_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_DES_CBC_ENCRYPT: | |
HAL_CRYP_DESCBC_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_DES_CBC_DECRYPT: | |
HAL_CRYP_DESCBC_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_AES_ECB_ENCRYPT: | |
HAL_CRYP_AESECB_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_AES_ECB_DECRYPT: | |
HAL_CRYP_AESECB_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_AES_CBC_ENCRYPT: | |
HAL_CRYP_AESCBC_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_AES_CBC_DECRYPT: | |
HAL_CRYP_AESCBC_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_AES_CTR_ENCRYPT: | |
HAL_CRYP_AESCTR_Encrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
case CRYP_CR_ALGOMODE_AES_CTR_DECRYPT: | |
HAL_CRYP_AESCTR_Decrypt_IT(hcryp, NULL, 0U, NULL); | |
break; | |
default: | |
break; | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group7 Peripheral State functions | |
* @brief Peripheral State functions. | |
* | |
@verbatim | |
============================================================================== | |
##### Peripheral State functions ##### | |
============================================================================== | |
[..] | |
This subsection permits to get in run-time the status of the peripheral. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Returns the CRYP state. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval HAL state | |
*/ | |
HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp) | |
{ | |
return hcryp->State; | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
#endif /* CRYP */ | |
#if defined (AES) | |
/** @defgroup AES AES | |
* @brief AES HAL module driver. | |
* @{ | |
*/ | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/* Private macro -------------------------------------------------------------*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private functions --------------------------------------------------------*/ | |
/** @defgroup CRYP_Private_Functions CRYP Private Functions | |
* @{ | |
*/ | |
static HAL_StatusTypeDef CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp); | |
static HAL_StatusTypeDef CRYP_SetKey(CRYP_HandleTypeDef *hcryp); | |
static HAL_StatusTypeDef CRYP_AES_IT(CRYP_HandleTypeDef *hcryp); | |
/** | |
* @} | |
*/ | |
/* Exported functions ---------------------------------------------------------*/ | |
/** @defgroup CRYP_Exported_Functions CRYP Exported Functions | |
* @{ | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group1 Initialization and deinitialization functions | |
* @brief Initialization and Configuration functions. | |
* | |
@verbatim | |
============================================================================== | |
##### Initialization and deinitialization functions ##### | |
============================================================================== | |
[..] This section provides functions allowing to: | |
(+) Initialize the CRYP according to the specified parameters | |
in the CRYP_InitTypeDef and creates the associated handle | |
(+) DeInitialize the CRYP peripheral | |
(+) Initialize the CRYP MSP (MCU Specific Package) | |
(+) De-Initialize the CRYP MSP | |
[..] | |
(@) Specific care must be taken to format the key and the Initialization Vector IV! | |
[..] If the key is defined as a 128-bit long array key[127..0] = {b127 ... b0} where | |
b127 is the MSB and b0 the LSB, the key must be stored in MCU memory | |
(+) as a sequence of words where the MSB word comes first (occupies the | |
lowest memory address) | |
(+) where each word is byte-swapped: | |
(++) address n+0 : 0b b103 .. b96 b111 .. b104 b119 .. b112 b127 .. b120 | |
(++) address n+4 : 0b b71 .. b64 b79 .. b72 b87 .. b80 b95 .. b88 | |
(++) address n+8 : 0b b39 .. b32 b47 .. b40 b55 .. b48 b63 .. b56 | |
(++) address n+C : 0b b7 .. b0 b15 .. b8 b23 .. b16 b31 .. b24 | |
[..] Hereafter, another illustration when considering a 128-bit long key made of 16 bytes {B15..B0}. | |
The 4 32-bit words that make the key must be stored as follows in MCU memory: | |
(+) address n+0 : 0x B12 B13 B14 B15 | |
(+) address n+4 : 0x B8 B9 B10 B11 | |
(+) address n+8 : 0x B4 B5 B6 B7 | |
(+) address n+C : 0x B0 B1 B2 B3 | |
[..] which leads to the expected setting | |
(+) AES_KEYR3 = 0x B15 B14 B13 B12 | |
(+) AES_KEYR2 = 0x B11 B10 B9 B8 | |
(+) AES_KEYR1 = 0x B7 B6 B5 B4 | |
(+) AES_KEYR0 = 0x B3 B2 B1 B0 | |
[..] Same format must be applied for a 256-bit long key made of 32 bytes {B31..B0}. | |
The 8 32-bit words that make the key must be stored as follows in MCU memory: | |
(+) address n+00 : 0x B28 B29 B30 B31 | |
(+) address n+04 : 0x B24 B25 B26 B27 | |
(+) address n+08 : 0x B20 B21 B22 B23 | |
(+) address n+0C : 0x B16 B17 B18 B19 | |
(+) address n+10 : 0x B12 B13 B14 B15 | |
(+) address n+14 : 0x B8 B9 B10 B11 | |
(+) address n+18 : 0x B4 B5 B6 B7 | |
(+) address n+1C : 0x B0 B1 B2 B3 | |
[..] which leads to the expected setting | |
(+) AES_KEYR7 = 0x B31 B30 B29 B28 | |
(+) AES_KEYR6 = 0x B27 B26 B25 B24 | |
(+) AES_KEYR5 = 0x B23 B22 B21 B20 | |
(+) AES_KEYR4 = 0x B19 B18 B17 B16 | |
(+) AES_KEYR3 = 0x B15 B14 B13 B12 | |
(+) AES_KEYR2 = 0x B11 B10 B9 B8 | |
(+) AES_KEYR1 = 0x B7 B6 B5 B4 | |
(+) AES_KEYR0 = 0x B3 B2 B1 B0 | |
[..] Initialization Vector IV (4 32-bit words) format must follow the same as | |
that of a 128-bit long key. | |
[..] | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Initialize the CRYP according to the specified | |
* parameters in the CRYP_InitTypeDef and initialize the associated handle. | |
* @note Specific care must be taken to format the key and the Initialization Vector IV | |
* stored in the MCU memory before calling HAL_CRYP_Init(). Refer to explanations | |
* hereabove. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_Init(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Check the CRYP handle allocation */ | |
if(hcryp == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check the instance */ | |
assert_param(IS_AES_ALL_INSTANCE(hcryp->Instance)); | |
/* Check the parameters */ | |
assert_param(IS_CRYP_KEYSIZE(hcryp->Init.KeySize)); | |
assert_param(IS_CRYP_DATATYPE(hcryp->Init.DataType)); | |
assert_param(IS_CRYP_ALGOMODE(hcryp->Init.OperatingMode)); | |
/* ChainingMode parameter is irrelevant when mode is set to Key derivation */ | |
if (hcryp->Init.OperatingMode != CRYP_ALGOMODE_KEYDERIVATION) | |
{ | |
assert_param(IS_CRYP_CHAINMODE(hcryp->Init.ChainingMode)); | |
} | |
assert_param(IS_CRYP_WRITE(hcryp->Init.KeyWriteFlag)); | |
/*========================================================*/ | |
/* Check the proper operating/chaining modes combinations */ | |
/*========================================================*/ | |
/* Check the proper chaining when the operating mode is key derivation and decryption */ | |
#if defined(AES_CR_NPBLB) | |
if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION_DECRYPT) &&\ | |
((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CTR) \ | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) \ | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC))) | |
#else | |
if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION_DECRYPT) &&\ | |
((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CTR) \ | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) \ | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC))) | |
#endif | |
{ | |
return HAL_ERROR; | |
} | |
/* Check that key derivation is not set in CMAC mode or CCM mode when applicable */ | |
#if defined(AES_CR_NPBLB) | |
if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) | |
&& (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)) | |
#else | |
if ((hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) | |
&& (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)) | |
#endif | |
{ | |
return HAL_ERROR; | |
} | |
/*================*/ | |
/* Initialization */ | |
/*================*/ | |
/* Initialization start */ | |
if(hcryp->State == HAL_CRYP_STATE_RESET) | |
{ | |
/* Allocate lock resource and initialize it */ | |
hcryp->Lock = HAL_UNLOCKED; | |
/* Init the low level hardware */ | |
HAL_CRYP_MspInit(hcryp); | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Disable the Peripheral */ | |
__HAL_CRYP_DISABLE(); | |
/*=============================================================*/ | |
/* AES initialization common to all operating modes */ | |
/*=============================================================*/ | |
/* Set the Key size selection */ | |
MODIFY_REG(hcryp->Instance->CR, AES_CR_KEYSIZE, hcryp->Init.KeySize); | |
/* Set the default CRYP phase when this parameter is not used. | |
Phase is updated below in case of GCM/GMAC/CMAC(/CCM) setting. */ | |
hcryp->Phase = HAL_CRYP_PHASE_NOT_USED; | |
/*=============================================================*/ | |
/* Carry on the initialization based on the AES operating mode */ | |
/*=============================================================*/ | |
/* Key derivation */ | |
if (hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION) | |
{ | |
MODIFY_REG(hcryp->Instance->CR, AES_CR_MODE, CRYP_ALGOMODE_KEYDERIVATION); | |
/* Configure the Key registers */ | |
if (CRYP_SetKey(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
else | |
/* Encryption / Decryption (with or without key derivation) / authentication */ | |
{ | |
/* Set data type, operating and chaining modes. | |
In case of GCM or GMAC, data type is forced to 0b00 */ | |
if (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) | |
{ | |
MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE|AES_CR_MODE|AES_CR_CHMOD, hcryp->Init.OperatingMode|hcryp->Init.ChainingMode); | |
} | |
else | |
{ | |
MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE|AES_CR_MODE|AES_CR_CHMOD, hcryp->Init.DataType|hcryp->Init.OperatingMode|hcryp->Init.ChainingMode); | |
} | |
/* Specify the encryption/decryption phase in case of Galois counter mode (GCM), | |
Galois message authentication code (GMAC), cipher message authentication code (CMAC) | |
or Counter with Cipher Mode (CCM) when applicable */ | |
#if defined(AES_CR_NPBLB) | |
if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)) | |
#else | |
if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)) | |
#endif | |
{ | |
MODIFY_REG(hcryp->Instance->CR, AES_CR_GCMPH, hcryp->Init.GCMCMACPhase); | |
hcryp->Phase = HAL_CRYP_PHASE_START; | |
} | |
/* Configure the Key registers if no need to bypass this step */ | |
if (hcryp->Init.KeyWriteFlag == CRYP_KEY_WRITE_ENABLE) | |
{ | |
if (CRYP_SetKey(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* If applicable, configure the Initialization Vector */ | |
if (hcryp->Init.ChainingMode != CRYP_CHAINMODE_AES_ECB) | |
{ | |
if (CRYP_SetInitVector(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
} | |
#if defined(AES_CR_NPBLB) | |
/* Clear NPBLB field */ | |
CLEAR_BIT(hcryp->Instance->CR, AES_CR_NPBLB); | |
#endif | |
/* Reset CrypInCount and CrypOutCount */ | |
hcryp->CrypInCount = 0U; | |
hcryp->CrypOutCount = 0U; | |
/* Reset ErrorCode field */ | |
hcryp->ErrorCode = HAL_CRYP_ERROR_NONE; | |
/* Reset Mode suspension request */ | |
hcryp->SuspendRequest = HAL_CRYP_SUSPEND_NONE; | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Enable the Peripheral */ | |
__HAL_CRYP_ENABLE(); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief DeInitialize the CRYP peripheral. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_DeInit(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Check the CRYP handle allocation */ | |
if(hcryp == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_BUSY; | |
/* Set the default CRYP phase */ | |
hcryp->Phase = HAL_CRYP_PHASE_READY; | |
/* Reset CrypInCount and CrypOutCount */ | |
hcryp->CrypInCount = 0U; | |
hcryp->CrypOutCount = 0U; | |
/* Disable the CRYP Peripheral Clock */ | |
__HAL_CRYP_DISABLE(); | |
/* DeInit the low level hardware: CLOCK, NVIC.*/ | |
HAL_CRYP_MspDeInit(hcryp); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_RESET; | |
/* Release Lock */ | |
__HAL_UNLOCK(hcryp); | |
/* Return function status */ | |
return HAL_OK; | |
} | |
/** | |
* @brief Initialize the CRYP MSP. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_MspInit(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function should not be modified; when the callback is needed, | |
the HAL_CRYP_MspInit can be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief DeInitialize CRYP MSP. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_MspDeInit(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function should not be modified; when the callback is needed, | |
the HAL_CRYP_MspDeInit can be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group2 AES processing functions | |
* @brief Processing functions. | |
* | |
@verbatim | |
============================================================================== | |
##### AES processing functions ##### | |
============================================================================== | |
[..] This section provides functions allowing to: | |
(+) Encrypt plaintext using AES algorithm in different chaining modes | |
(+) Decrypt cyphertext using AES algorithm in different chaining modes | |
[..] Three processing functions are available: | |
(+) Polling mode | |
(+) Interrupt mode | |
(+) DMA mode | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Encrypt pPlainData in AES ECB encryption mode. The cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES CBC encryption mode with key derivation. The cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES CTR encryption mode. The cypher data are available in pCypherData | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Timeout Specify Timeout value | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData, uint32_t Timeout) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES(hcryp, pPlainData, Size, pCypherData, Timeout); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES ECB decryption mode with key derivation, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES ECB decryption mode with key derivation, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES CTR decryption mode, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Timeout Specify Timeout value | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData, uint32_t Timeout) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES(hcryp, pCypherData, Size, pPlainData, Timeout); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES ECB encryption mode using Interrupt, | |
* the cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES CBC encryption mode using Interrupt, | |
* the cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES CTR encryption mode using Interrupt, | |
* the cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_IT(hcryp, pPlainData, Size, pCypherData); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES ECB decryption mode using Interrupt, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer. | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES CBC decryption mode using Interrupt, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES CTR decryption mode using Interrupt, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_IT() API instead (usage recommended). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_IT(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_IT(hcryp, pCypherData, Size, pPlainData); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES ECB encryption mode using DMA, | |
* the cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). | |
* @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES CBC encryption mode using DMA, | |
* the cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). | |
* @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData); | |
} | |
/** | |
* @brief Encrypt pPlainData in AES CTR encryption mode using DMA, | |
* the cypher data are available in pCypherData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pPlainData Pointer to the plaintext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pCypherData Pointer to the cyphertext buffer. | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). | |
* @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Encrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pPlainData, uint16_t Size, uint8_t *pCypherData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_ENCRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_DMA(hcryp, pPlainData, Size, pCypherData); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES ECB decryption mode using DMA, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). | |
* @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESECB_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_ECB; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES CBC decryption mode using DMA, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). | |
* @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCBC_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_KEYDERIVATION_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CBC; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData); | |
} | |
/** | |
* @brief Decrypt pCypherData in AES CTR decryption mode using DMA, | |
* the decyphered data are available in pPlainData. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @param pCypherData Pointer to the cyphertext buffer | |
* @param Size Length of the plaintext buffer in bytes, must be a multiple of 16. | |
* @param pPlainData Pointer to the plaintext buffer | |
* @note This API is provided only to maintain compatibility with legacy software. Users should directly | |
* resort to generic HAL_CRYPEx_AES_DMA() API instead (usage recommended). | |
* @note pPlainData and pCypherData buffers must be 32-bit aligned to ensure a correct DMA transfer to and from the IP. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_CRYP_AESCTR_Decrypt_DMA(CRYP_HandleTypeDef *hcryp, uint8_t *pCypherData, uint16_t Size, uint8_t *pPlainData) | |
{ | |
/* Re-initialize AES IP with proper parameters */ | |
if (HAL_CRYP_DeInit(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
hcryp->Init.OperatingMode = CRYP_ALGOMODE_DECRYPT; | |
hcryp->Init.ChainingMode = CRYP_CHAINMODE_AES_CTR; | |
hcryp->Init.KeyWriteFlag = CRYP_KEY_WRITE_ENABLE; | |
if (HAL_CRYP_Init(hcryp) != HAL_OK) | |
{ | |
return HAL_ERROR; | |
} | |
return HAL_CRYPEx_AES_DMA(hcryp, pCypherData, Size, pPlainData); | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group3 Callback functions | |
* @brief Callback functions. | |
* | |
@verbatim | |
============================================================================== | |
##### Callback functions ##### | |
============================================================================== | |
[..] This section provides Interruption and DMA callback functions: | |
(+) DMA Input data transfer complete | |
(+) DMA Output data transfer complete | |
(+) DMA or Interrupt error | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief CRYP error callback. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_ErrorCallback(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function should not be modified; when the callback is needed, | |
the HAL_CRYP_ErrorCallback can be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Input DMA transfer complete callback. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_InCpltCallback(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function should not be modified; when the callback is needed, | |
the HAL_CRYP_InCpltCallback can be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Output DMA transfer complete callback. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
__weak void HAL_CRYP_OutCpltCallback(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(hcryp); | |
/* NOTE : This function should not be modified; when the callback is needed, | |
the HAL_CRYP_OutCpltCallback can be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group4 CRYP IRQ handler | |
* @brief AES IRQ handler. | |
* | |
@verbatim | |
============================================================================== | |
##### AES IRQ handler management ##### | |
============================================================================== | |
[..] This section provides AES IRQ handler function. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Handle AES interrupt request. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
void HAL_CRYP_IRQHandler(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Check if error occurred */ | |
if (__HAL_CRYP_GET_IT_SOURCE(CRYP_IT_ERRIE) != RESET) | |
{ | |
/* If Write Error occurred */ | |
if (__HAL_CRYP_GET_FLAG(CRYP_IT_WRERR) != RESET) | |
{ | |
hcryp->ErrorCode |= HAL_CRYP_WRITE_ERROR; | |
hcryp->State = HAL_CRYP_STATE_ERROR; | |
} | |
/* If Read Error occurred */ | |
if (__HAL_CRYP_GET_FLAG(CRYP_IT_RDERR) != RESET) | |
{ | |
hcryp->ErrorCode |= HAL_CRYP_READ_ERROR; | |
hcryp->State = HAL_CRYP_STATE_ERROR; | |
} | |
/* If an error has been reported */ | |
if (hcryp->State == HAL_CRYP_STATE_ERROR) | |
{ | |
/* Disable Error and Computation Complete Interrupts */ | |
__HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE); | |
/* Clear all Interrupt flags */ | |
__HAL_CRYP_CLEAR_FLAG(CRYP_ERR_CLEAR|CRYP_CCF_CLEAR); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
HAL_CRYP_ErrorCallback(hcryp); | |
return; | |
} | |
} | |
/* Check if computation complete interrupt is enabled | |
and if the computation complete flag is raised */ | |
if((__HAL_CRYP_GET_FLAG(CRYP_IT_CCF) != RESET) && (__HAL_CRYP_GET_IT_SOURCE(CRYP_IT_CCFIE) != RESET)) | |
{ | |
#if defined(AES_CR_NPBLB) | |
if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CCM_CMAC)) | |
#else | |
if ((hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_GCM_GMAC) | |
|| (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC)) | |
#endif | |
{ | |
/* To ensure proper suspension requests management, CCF flag | |
is reset in CRYP_AES_Auth_IT() according to the current | |
phase under handling */ | |
CRYP_AES_Auth_IT(hcryp); | |
} | |
else | |
{ | |
/* Clear Computation Complete Flag */ | |
__HAL_CRYP_CLEAR_FLAG(CRYP_CCF_CLEAR); | |
CRYP_AES_IT(hcryp); | |
} | |
} | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup CRYP_Exported_Functions_Group5 Peripheral State functions | |
* @brief Peripheral State functions. | |
* | |
@verbatim | |
============================================================================== | |
##### Peripheral State functions ##### | |
============================================================================== | |
[..] | |
This subsection permits to get in run-time the status of the peripheral. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Return the CRYP handle state. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval HAL state | |
*/ | |
HAL_CRYP_STATETypeDef HAL_CRYP_GetState(CRYP_HandleTypeDef *hcryp) | |
{ | |
/* Return CRYP handle state */ | |
return hcryp->State; | |
} | |
/** | |
* @brief Return the CRYP peripheral error. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @note The returned error is a bit-map combination of possible errors | |
* @retval Error bit-map | |
*/ | |
uint32_t HAL_CRYP_GetError(CRYP_HandleTypeDef *hcryp) | |
{ | |
return hcryp->ErrorCode; | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/** @addtogroup CRYP_Private_Functions | |
* @{ | |
*/ | |
/** | |
* @brief Write the Key in KeyRx registers. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
static HAL_StatusTypeDef CRYP_SetKey(CRYP_HandleTypeDef *hcryp) | |
{ | |
uint32_t keyaddr = 0x0U; | |
if ((uint32_t)(hcryp->Init.pKey == NULL)) | |
{ | |
return HAL_ERROR; | |
} | |
keyaddr = (uint32_t)(hcryp->Init.pKey); | |
if (hcryp->Init.KeySize == CRYP_KEYSIZE_256B) | |
{ | |
hcryp->Instance->KEYR7 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->KEYR6 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->KEYR5 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->KEYR4 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
} | |
hcryp->Instance->KEYR3 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->KEYR2 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->KEYR1 = __REV(*(uint32_t*)(keyaddr)); | |
keyaddr+=4U; | |
hcryp->Instance->KEYR0 = __REV(*(uint32_t*)(keyaddr)); | |
return HAL_OK; | |
} | |
/** | |
* @brief Write the InitVector/InitCounter in IVRx registers. | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module | |
* @retval None | |
*/ | |
static HAL_StatusTypeDef CRYP_SetInitVector(CRYP_HandleTypeDef *hcryp) | |
{ | |
uint32_t ivaddr = 0x0U; | |
#if !defined(AES_CR_NPBLB) | |
if (hcryp->Init.ChainingMode == CRYP_CHAINMODE_AES_CMAC) | |
{ | |
hcryp->Instance->IVR3 = 0U; | |
hcryp->Instance->IVR2 = 0U; | |
hcryp->Instance->IVR1 = 0U; | |
hcryp->Instance->IVR0 = 0U; | |
} | |
else | |
#endif | |
{ | |
if (hcryp->Init.pInitVect == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
ivaddr = (uint32_t)(hcryp->Init.pInitVect); | |
hcryp->Instance->IVR3 = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IVR2 = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IVR1 = __REV(*(uint32_t*)(ivaddr)); | |
ivaddr+=4U; | |
hcryp->Instance->IVR0 = __REV(*(uint32_t*)(ivaddr)); | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Handle CRYP block input/output data handling under interruption. | |
* @note The function is called under interruption only, once | |
* interruptions have been enabled by HAL_CRYPEx_AES_IT(). | |
* @param hcryp pointer to a CRYP_HandleTypeDef structure that contains | |
* the configuration information for CRYP module. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef CRYP_AES_IT(CRYP_HandleTypeDef *hcryp) | |
{ | |
uint32_t inputaddr = 0U; | |
uint32_t outputaddr = 0U; | |
if(hcryp->State == HAL_CRYP_STATE_BUSY) | |
{ | |
if (hcryp->Init.OperatingMode != CRYP_ALGOMODE_KEYDERIVATION) | |
{ | |
/* Get the output data address */ | |
outputaddr = (uint32_t)hcryp->pCrypOutBuffPtr; | |
/* Read the last available output block from the Data Output Register */ | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = hcryp->Instance->DOUTR; | |
hcryp->pCrypOutBuffPtr += 16U; | |
hcryp->CrypOutCount -= 16U; | |
} | |
else | |
{ | |
/* Read the derived key from the Key registers */ | |
if (hcryp->Init.KeySize == CRYP_KEYSIZE_256B) | |
{ | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR7); | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR6); | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR5); | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR4); | |
outputaddr+=4U; | |
} | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR3); | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR2); | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR1); | |
outputaddr+=4U; | |
*(uint32_t*)(outputaddr) = __REV(hcryp->Instance->KEYR0); | |
} | |
/* In case of ciphering or deciphering, check if all output text has been retrieved; | |
In case of key derivation, stop right there */ | |
if ((hcryp->CrypOutCount == 0U) || (hcryp->Init.OperatingMode == CRYP_ALGOMODE_KEYDERIVATION)) | |
{ | |
/* Disable Computation Complete Flag and Errors Interrupts */ | |
__HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
/* Call computation complete callback */ | |
HAL_CRYPEx_ComputationCpltCallback(hcryp); | |
return HAL_OK; | |
} | |
/* If suspension flag has been raised, suspend processing */ | |
else if (hcryp->SuspendRequest == HAL_CRYP_SUSPEND) | |
{ | |
/* reset ModeSuspend */ | |
hcryp->SuspendRequest = HAL_CRYP_SUSPEND_NONE; | |
/* Disable Computation Complete Flag and Errors Interrupts */ | |
__HAL_CRYP_DISABLE_IT(CRYP_IT_CCFIE|CRYP_IT_ERRIE); | |
/* Change the CRYP state */ | |
hcryp->State = HAL_CRYP_STATE_SUSPENDED; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(hcryp); | |
return HAL_OK; | |
} | |
else /* Process the rest of input data */ | |
{ | |
/* Get the Intput data address */ | |
inputaddr = (uint32_t)hcryp->pCrypInBuffPtr; | |
/* Increment/decrement instance pointer/counter */ | |
hcryp->pCrypInBuffPtr += 16U; | |
hcryp->CrypInCount -= 16U; | |
/* Write the next input block in the Data Input register */ | |
hcryp->Instance->DINR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DINR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DINR = *(uint32_t*)(inputaddr); | |
inputaddr+=4U; | |
hcryp->Instance->DINR = *(uint32_t*)(inputaddr); | |
return HAL_OK; | |
} | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @} | |
*/ | |
#endif /* AES */ | |
#endif /* HAL_CRYP_MODULE_ENABLED */ | |
/** | |
* @} | |
*/ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |