boards/nxp/frdm_mcxn947/doc/index.rst - third_party/github/zephyrproject-rtos/zephyr - Git at Google

 .. _frdm_mcxn947:

 NXP FRDM-MCXN947
 ################

 Overview
 ********

 FRDM-MCXN947 are compact and scalable development boards for rapid prototyping of
 MCX N94 and N54 MCUs. They offer industry standard headers for easy access to the
 MCUs I/Os, integrated open-standard serial interfaces, external flash memory and
 an on-board MCU-Link debugger. MCX N Series are high-performance, low-power
 microcontrollers with intelligent peripherals and accelerators providing multi-tasking
 capabilities and performance efficiency.

 .. image:: frdm_mcxn947.webp
    :align: center
    :alt: FRDM-MCXN947

 Hardware
 ********

 - MCX-N947 Dual Arm Cortex-M33 microcontroller running at 150 MHz
 - 2MB dual-bank on chip Flash
 - 512 KB RAM
 - External Quad SPI flash over FlexSPI
 - USB high-speed (Host/Device) with on-chip HS PHY. HS USB Type-C connectors
 - 10x LP Flexcomms each supporting SPI, I2C, UART
 - 2x FlexCAN with FD, 2x I3Cs, 2x SAI
 - 1x Ethernet with QoS
 - On-board MCU-Link debugger with CMSIS-DAP
 - Arduino Header, FlexIO/LCD Header, SmartDMA/Camera Header, mikroBUS

 For more information about the MCX-N947 SoC and FRDM-MCXN947 board, see:

 - `MCX-N947 SoC Website`_
 - `MCX-N947 Datasheet`_
 - `MCX-N947 Reference Manual`_
 - `FRDM-MCXN947 Website`_
 - `FRDM-MCXN947 User Guide`_
 - `FRDM-MCXN947 Schematics`_

 Supported Features
 ==================

 The FRDM-MCXN947 board configuration supports the following hardware features:

 +-----------+------------+-------------------------------------+
 | Interface | Controller | Driver/Component                    |
 +===========+============+=====================================+
 | NVIC      | on-chip    | nested vector interrupt controller  |
 +-----------+------------+-------------------------------------+
 | SYSTICK   | on-chip    | systick                             |
 +-----------+------------+-------------------------------------+
 | PINMUX    | on-chip    | pinmux                              |
 +-----------+------------+-------------------------------------+
 | GPIO      | on-chip    | gpio                                |
 +-----------+------------+-------------------------------------+
 | UART      | on-chip    | serial port-polling;                |
 |           |            | serial port-interrupt               |
 +-----------+------------+-------------------------------------+
 | SPI       | on-chip    | spi                                 |
 +-----------+------------+-------------------------------------+
 | DMA       | on-chip    | dma                                 |
 +-----------+------------+-------------------------------------+
 | CLOCK     | on-chip    | clock_control                       |
 +-----------+------------+-------------------------------------+
 | FLASH     | on-chip    | soc flash                           |
 +-----------+------------+-------------------------------------+
 | FLEXSPI   | on-chip    | flash programming                   |
 +-----------+------------+-------------------------------------+
 | DAC       | on-chip    | dac                                 |
 +-----------+------------+-------------------------------------+

 Targets available
 ==================

 The default configuration file
 :zephyr_file:`boards/nxp/frdm_mcxn947/frdm_mcxn947_mcxn947_cpu0_defconfig`
 only enables the first core.

 Other hardware features are not currently supported by the port.

 Connections and IOs
 ===================

 The MCX-N947 SoC has 6 gpio controllers and has pinmux registers which
 can be used to configure the functionality of a pin.

 +------------+-----------------+----------------------------+
 | Name       | Function        | Usage                      |
 +============+=================+============================+
 | P0_PIO1_8  | UART            | UART RX                    |
 +------------+-----------------+----------------------------+
 | P1_PIO1_9  | UART            | UART TX                    |
 +------------+-----------------+----------------------------+

 System Clock
 ============

 The MCX-N947 SoC is configured to use PLL0 running at 150MHz as a source for
 the system clock.

 Serial Port
 ===========

 The FRDM-MCXN947 SoC has 10 FLEXCOMM interfaces for serial communication.
 Flexcomm 4 is configured as UART for the console.

 Programming and Debugging
 *************************

 Build and flash applications as usual (see :ref:`build_an_application` and
 :ref:`application_run` for more details).

 Configuring a Debug Probe
 =========================

 A debug probe is used for both flashing and debugging the board. This board is
 configured by default to use the MCU-Link CMSIS-DAP Onboard Debug Probe.

 Using LinkServer
 ----------------

 Linkserver is the default runner for this board, and supports the factory
 default MCU-Link firmware. Follow the instructions in
 :ref:`mcu-link-cmsis-onboard-debug-probe` to reprogram the default MCU-Link
 firmware. This only needs to be done if the default onboard debug circuit
 firmware was changed. To put the board in ``DFU mode`` to program the firmware,
 short jumper J21.

 Using J-Link
 ------------

 There are two options. The onboard debug circuit can be updated with Segger
 J-Link firmware by following the instructions in
 :ref:`mcu-link-jlink-onboard-debug-probe`.
 To put the board in ``DFU mode`` to program the firmware, short jumper J21.
 The second option is to attach :ref:`jlink-external-debug-probe` to the
 board.

 Use the ``-r jlink`` option with west to use the jlink runner.

 .. code-block:: console

    west flash -r jlink

 Configuring a Console
 =====================

 Connect a USB cable from your PC to J17, and use the serial terminal of your choice
 (minicom, putty, etc.) with the following settings:

 - Speed: 115200
 - Data: 8 bits
 - Parity: None
 - Stop bits: 1

 Flashing
 ========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: frdm_mcxn947/mcxn947/cpu0
    :goals: flash

 Open a serial terminal, reset the board (press the RESET button), and you should
 see the following message in the terminal:

 .. code-block:: console

    *** Booting Zephyr OS build v3.6.0-479-g91faa20c6741 ***
    Hello World! frdm_mcxn947/mcxn947/cpu0

 Debugging
 =========

 Here is an example for the :ref:`hello_world` application.

 .. zephyr-app-commands::
    :zephyr-app: samples/hello_world
    :board: frdm_mcxn947/mcxn947/cpu0
    :goals: debug

 Open a serial terminal, step through the application in your debugger, and you
 should see the following message in the terminal:

 .. code-block:: console

    *** Booting Zephyr OS build v3.6.0-479-g91faa20c6741 ***
    Hello World! frdm_mcxn947/mcxn947/cpu0

 .. _MCX-N947 SoC Website:
    https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/general-purpose-mcus/mcx-arm-cortex-m/mcx-n-series-microcontrollers/mcx-n94x-54x-highly-integrated-multicore-mcus-with-on-chip-accelerators-intelligent-peripherals-and-advanced-security:MCX-N94X-N54X

 .. _MCX-N947 Datasheet:
    https://www.nxp.com/docs/en/data-sheet/MCXNx4xDS.pdf

 .. _MCX-N947 Reference Manual:
    https://www.nxp.com/webapp/Download?colCode=MCXNX4XRM

 .. _FRDM-MCXN947 Website:
    https://www.nxp.com/design/design-center/development-boards/general-purpose-mcus/frdm-development-board-for-mcx-n94-n54-mcus:FRDM-MCXN947

 .. _FRDM-MCXN947 User Guide:
    https://www.nxp.com/document/guide/getting-started-with-frdm-mcxn947:GS-FRDM-MCXNXX

 .. _FRDM-MCXN947 Debug Firmware:
    https://www.nxp.com/docs/en/application-note/AN13206.pdf

 .. _FRDM-MCXN947 Schematics:
    https://www.nxp.com/webapp/Download?colCode=LPC55S69-SCH
	.. _frdm_mcxn947:

	NXP FRDM-MCXN947
	################

	Overview
	********

	FRDM-MCXN947 are compact and scalable development boards for rapid prototyping of
	MCX N94 and N54 MCUs. They offer industry standard headers for easy access to the
	MCUs I/Os, integrated open-standard serial interfaces, external flash memory and
	an on-board MCU-Link debugger. MCX N Series are high-performance, low-power
	microcontrollers with intelligent peripherals and accelerators providing multi-tasking
	capabilities and performance efficiency.

	.. image:: frdm_mcxn947.webp
	:align: center
	:alt: FRDM-MCXN947

	Hardware
	********

	- MCX-N947 Dual Arm Cortex-M33 microcontroller running at 150 MHz
	- 2MB dual-bank on chip Flash
	- 512 KB RAM
	- External Quad SPI flash over FlexSPI
	- USB high-speed (Host/Device) with on-chip HS PHY. HS USB Type-C connectors
	- 10x LP Flexcomms each supporting SPI, I2C, UART
	- 2x FlexCAN with FD, 2x I3Cs, 2x SAI
	- 1x Ethernet with QoS
	- On-board MCU-Link debugger with CMSIS-DAP
	- Arduino Header, FlexIO/LCD Header, SmartDMA/Camera Header, mikroBUS

	For more information about the MCX-N947 SoC and FRDM-MCXN947 board, see:

	- `MCX-N947 SoC Website`_
	- `MCX-N947 Datasheet`_
	- `MCX-N947 Reference Manual`_
	- `FRDM-MCXN947 Website`_
	- `FRDM-MCXN947 User Guide`_
	- `FRDM-MCXN947 Schematics`_

	Supported Features
	==================

	The FRDM-MCXN947 board configuration supports the following hardware features:

	+-----------+------------+-------------------------------------+
	\| Interface \| Controller \| Driver/Component \|
	+===========+============+=====================================+
	\| NVIC \| on-chip \| nested vector interrupt controller \|
	+-----------+------------+-------------------------------------+
	\| SYSTICK \| on-chip \| systick \|
	+-----------+------------+-------------------------------------+
	\| PINMUX \| on-chip \| pinmux \|
	+-----------+------------+-------------------------------------+
	\| GPIO \| on-chip \| gpio \|
	+-----------+------------+-------------------------------------+
	\| UART \| on-chip \| serial port-polling; \|
	\| \| \| serial port-interrupt \|
	+-----------+------------+-------------------------------------+
	\| SPI \| on-chip \| spi \|
	+-----------+------------+-------------------------------------+
	\| DMA \| on-chip \| dma \|
	+-----------+------------+-------------------------------------+
	\| CLOCK \| on-chip \| clock_control \|
	+-----------+------------+-------------------------------------+
	\| FLASH \| on-chip \| soc flash \|
	+-----------+------------+-------------------------------------+
	\| FLEXSPI \| on-chip \| flash programming \|
	+-----------+------------+-------------------------------------+
	\| DAC \| on-chip \| dac \|
	+-----------+------------+-------------------------------------+

	Targets available
	==================

	The default configuration file
	:zephyr_file:`boards/nxp/frdm_mcxn947/frdm_mcxn947_mcxn947_cpu0_defconfig`
	only enables the first core.

	Other hardware features are not currently supported by the port.

	Connections and IOs
	===================

	The MCX-N947 SoC has 6 gpio controllers and has pinmux registers which
	can be used to configure the functionality of a pin.

	+------------+-----------------+----------------------------+
	\| Name \| Function \| Usage \|
	+============+=================+============================+
	\| P0_PIO1_8 \| UART \| UART RX \|
	+------------+-----------------+----------------------------+
	\| P1_PIO1_9 \| UART \| UART TX \|
	+------------+-----------------+----------------------------+

	System Clock
	============

	The MCX-N947 SoC is configured to use PLL0 running at 150MHz as a source for
	the system clock.

	Serial Port
	===========

	The FRDM-MCXN947 SoC has 10 FLEXCOMM interfaces for serial communication.
	Flexcomm 4 is configured as UART for the console.

	Programming and Debugging
	*************************

	Build and flash applications as usual (see :ref:`build_an_application` and
	:ref:`application_run` for more details).

	Configuring a Debug Probe
	=========================

	A debug probe is used for both flashing and debugging the board. This board is
	configured by default to use the MCU-Link CMSIS-DAP Onboard Debug Probe.

	Using LinkServer
	----------------

	Linkserver is the default runner for this board, and supports the factory
	default MCU-Link firmware. Follow the instructions in
	:ref:`mcu-link-cmsis-onboard-debug-probe` to reprogram the default MCU-Link
	firmware. This only needs to be done if the default onboard debug circuit
	firmware was changed. To put the board in ``DFU mode`` to program the firmware,
	short jumper J21.

	Using J-Link
	------------

	There are two options. The onboard debug circuit can be updated with Segger
	J-Link firmware by following the instructions in
	:ref:`mcu-link-jlink-onboard-debug-probe`.
	To put the board in ``DFU mode`` to program the firmware, short jumper J21.
	The second option is to attach :ref:`jlink-external-debug-probe` to the
	board.

	Use the ``-r jlink`` option with west to use the jlink runner.

	.. code-block:: console

	west flash -r jlink

	Configuring a Console
	=====================

	Connect a USB cable from your PC to J17, and use the serial terminal of your choice
	(minicom, putty, etc.) with the following settings:

	- Speed: 115200
	- Data: 8 bits
	- Parity: None
	- Stop bits: 1

	Flashing
	========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: frdm_mcxn947/mcxn947/cpu0
	:goals: flash

	Open a serial terminal, reset the board (press the RESET button), and you should
	see the following message in the terminal:

	.. code-block:: console

	* Booting Zephyr OS build v3.6.0-479-g91faa20c6741 *
	Hello World! frdm_mcxn947/mcxn947/cpu0

	Debugging
	=========

	Here is an example for the :ref:`hello_world` application.

	.. zephyr-app-commands::
	:zephyr-app: samples/hello_world
	:board: frdm_mcxn947/mcxn947/cpu0
	:goals: debug

	Open a serial terminal, step through the application in your debugger, and you
	should see the following message in the terminal:

	.. code-block:: console

	* Booting Zephyr OS build v3.6.0-479-g91faa20c6741 *
	Hello World! frdm_mcxn947/mcxn947/cpu0

	.. _MCX-N947 SoC Website:
	https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/general-purpose-mcus/mcx-arm-cortex-m/mcx-n-series-microcontrollers/mcx-n94x-54x-highly-integrated-multicore-mcus-with-on-chip-accelerators-intelligent-peripherals-and-advanced-security:MCX-N94X-N54X

	.. _MCX-N947 Datasheet:
	https://www.nxp.com/docs/en/data-sheet/MCXNx4xDS.pdf

	.. _MCX-N947 Reference Manual:
	https://www.nxp.com/webapp/Download?colCode=MCXNX4XRM

	.. _FRDM-MCXN947 Website:
	https://www.nxp.com/design/design-center/development-boards/general-purpose-mcus/frdm-development-board-for-mcx-n94-n54-mcus:FRDM-MCXN947

	.. _FRDM-MCXN947 User Guide:
	https://www.nxp.com/document/guide/getting-started-with-frdm-mcxn947:GS-FRDM-MCXNXX

	.. _FRDM-MCXN947 Debug Firmware:
	https://www.nxp.com/docs/en/application-note/AN13206.pdf

	.. _FRDM-MCXN947 Schematics:
	https://www.nxp.com/webapp/Download?colCode=LPC55S69-SCH