| .. _sparkfun_pro_micro_rp2040: |
| |
| SparkFun Pro Micro RP2040 |
| ######################### |
| |
| Overview |
| ******** |
| |
| The SparkFun Pro Micro RP2040 is a small, low-cost, versatile board from |
| SparkFun. It is equipped with an RP2040 SoC, an on-board WS2812 addressable |
| LED, a USB connector, and a Qwiic connector. The USB bootloader allows it |
| to be flashed without any adapter, in a drag-and-drop manner. |
| |
| Hardware |
| ******** |
| - Dual core Arm Cortex-M0+ processor running up to 133MHz |
| - 264KB on-chip SRAM |
| - 16MB on-board QSPI flash with XIP capabilities |
| - 18 GPIO pins |
| - 4 Analog inputs |
| - 1 UART peripherals |
| - 1 SPI controllers |
| - 2 I2C controllers (one via Qwiic connector) |
| - 16 PWM channels |
| - USB 1.1 controller (host/device) |
| - 8 Programmable I/O (PIO) for custom peripherals |
| - On-board RGB LED |
| - 1 Watchdog timer peripheral |
| |
| |
| .. figure:: img/sparkfun_pro_micro_rp2040.jpg |
| :align: center |
| :alt: SparkFun Pro Micro RP2040 |
| |
| SparkFun Pro Micro RP2040 (Image courtesy of SparkFun) |
| |
| Supported Features |
| ================== |
| |
| The sparkfun_pro_micro_rp2040 board configuration supports the following |
| hardware features: |
| |
| .. list-table:: |
| :header-rows: 1 |
| |
| * - Peripheral |
| - Kconfig option |
| - Devicetree compatible |
| * - NVIC |
| - N/A |
| - :dtcompatible:`arm,v6m-nvic` |
| * - UART |
| - :kconfig:option:`CONFIG_SERIAL` |
| - :dtcompatible:`raspberrypi,pico-uart` |
| * - GPIO |
| - :kconfig:option:`CONFIG_GPIO` |
| - :dtcompatible:`raspberrypi,pico-gpio` |
| * - ADC |
| - :kconfig:option:`CONFIG_ADC` |
| - :dtcompatible:`raspberrypi,pico-adc` |
| * - I2C |
| - :kconfig:option:`CONFIG_I2C` |
| - :dtcompatible:`snps,designware-i2c` |
| * - SPI |
| - :kconfig:option:`CONFIG_SPI` |
| - :dtcompatible:`raspberrypi,pico-spi` |
| * - USB Device |
| - :kconfig:option:`CONFIG_USB_DEVICE_STACK` |
| - :dtcompatible:`raspberrypi,pico-usbd` |
| * - HWINFO |
| - :kconfig:option:`CONFIG_HWINFO` |
| - N/A |
| * - Watchdog Timer (WDT) |
| - :kconfig:option:`CONFIG_WATCHDOG` |
| - :dtcompatible:`raspberrypi,pico-watchdog` |
| * - PWM |
| - :kconfig:option:`CONFIG_PWM` |
| - :dtcompatible:`raspberrypi,pico-pwm` |
| * - Flash |
| - :kconfig:option:`CONFIG_FLASH` |
| - :dtcompatible:`raspberrypi,pico-flash` |
| * - Clock controller |
| - :kconfig:option:`CONFIG_CLOCK_CONTROL` |
| - :dtcompatible:`raspberrypi,pico-clock-controller` |
| * - UART (PIO) |
| - :kconfig:option:`CONFIG_SERIAL` |
| - :dtcompatible:`raspberrypi,pico-uart-pio` |
| |
| Pin Mapping |
| =========== |
| |
| The peripherals of the RP2040 SoC can be routed to various pins on the board. |
| The configuration of these routes can be modified through DTS. Please refer to |
| the datasheet to see the possible routings for each peripheral. |
| |
| Default Zephyr Peripheral Mapping: |
| ---------------------------------- |
| |
| .. rst-class:: rst-columns |
| |
| - UART0_TX : P0 |
| - UART0_RX : P1 |
| - I2C1_SDA : P2 |
| - I2C1_SCL : P3 |
| - SPI0_RX : P20 |
| - SPI0_SCK : P18 |
| - SPI0_TX : P19 |
| |
| Programming and Debugging |
| ************************* |
| |
| Flashing |
| ======== |
| |
| Using UF2 |
| --------- |
| |
| Since it doesn't expose the SWD pins, you must flash the SparkFun Pro Micro |
| RP2040 with a UF2 file. By default, building an app for this board will |
| generate a `build/zephyr/zephyr.uf2` file. If the Pro Micro RP2040 is powered |
| on with the `BOOTSEL` button pressed, it will appear on the host as a mass |
| storage device. The UF2 file should be drag-and-dropped to the device, which |
| will flash the Pro Micro RP2040. |
| |
| .. target-notes:: |
| |
| .. _Getting Started with Raspberry Pi Pico: |
| https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf |
| |
| .. _Graphical Datasheet: |
| https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf |
