| /* |
| * Copyright 2020 Broadcom |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #include <zephyr/device.h> |
| #include <zephyr/kernel.h> |
| #include <zephyr/arch/cpu.h> |
| #include <zephyr/sys/__assert.h> |
| #include <zephyr/sw_isr_table.h> |
| #include <zephyr/dt-bindings/interrupt-controller/arm-gic.h> |
| #include <zephyr/drivers/interrupt_controller/gic.h> |
| #include <zephyr/sys/barrier.h> |
| #include "intc_gic_common_priv.h" |
| #include "intc_gicv3_priv.h" |
| |
| #include <string.h> |
| |
| #define DT_DRV_COMPAT arm_gic_v3 |
| |
| /* Redistributor base addresses for each core */ |
| mem_addr_t gic_rdists[CONFIG_MP_MAX_NUM_CPUS]; |
| |
| #if defined(CONFIG_ARMV8_A_NS) || defined(CONFIG_GIC_SINGLE_SECURITY_STATE) |
| #define IGROUPR_VAL 0xFFFFFFFFU |
| #else |
| #define IGROUPR_VAL 0x0U |
| #endif |
| |
| /* |
| * We allocate memory for PROPBASE to cover 2 ^ lpi_id_bits LPIs to |
| * deal with (one configuration byte per interrupt). PENDBASE has to |
| * be 64kB aligned (one bit per LPI, plus 8192 bits for SPI/PPI/SGI). |
| */ |
| #define ITS_MAX_LPI_NRBITS 16 /* 64K LPIs */ |
| |
| #define LPI_PROPBASE_SZ(nrbits) ROUND_UP(BIT(nrbits), KB(64)) |
| #define LPI_PENDBASE_SZ(nrbits) ROUND_UP(BIT(nrbits) / 8, KB(64)) |
| |
| #ifdef CONFIG_GIC_V3_ITS |
| static uintptr_t lpi_prop_table; |
| |
| atomic_t nlpi_intid = ATOMIC_INIT(8192); |
| #endif |
| |
| static inline mem_addr_t gic_get_rdist(void) |
| { |
| return gic_rdists[arch_curr_cpu()->id]; |
| } |
| |
| /* |
| * Wait for register write pending |
| * TODO: add timed wait |
| */ |
| static int gic_wait_rwp(uint32_t intid) |
| { |
| uint32_t rwp_mask; |
| mem_addr_t base; |
| |
| if (intid < GIC_SPI_INT_BASE) { |
| base = (gic_get_rdist() + GICR_CTLR); |
| rwp_mask = BIT(GICR_CTLR_RWP); |
| } else { |
| base = GICD_CTLR; |
| rwp_mask = BIT(GICD_CTLR_RWP); |
| } |
| |
| while (sys_read32(base) & rwp_mask) { |
| ; |
| } |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_GIC_V3_ITS |
| static void arm_gic_lpi_setup(unsigned int intid, bool enable) |
| { |
| uint8_t *cfg = &((uint8_t *)lpi_prop_table)[intid - 8192]; |
| |
| if (enable) { |
| *cfg |= BIT(0); |
| } else { |
| *cfg &= ~BIT(0); |
| } |
| |
| barrier_dsync_fence_full(); |
| |
| its_rdist_invall(); |
| } |
| |
| static void arm_gic_lpi_set_priority(unsigned int intid, unsigned int prio) |
| { |
| uint8_t *cfg = &((uint8_t *)lpi_prop_table)[intid - 8192]; |
| |
| *cfg &= 0xfc; |
| *cfg |= prio & 0xfc; |
| |
| barrier_dsync_fence_full(); |
| |
| its_rdist_invall(); |
| } |
| |
| static bool arm_gic_lpi_is_enabled(unsigned int intid) |
| { |
| uint8_t *cfg = &((uint8_t *)lpi_prop_table)[intid - 8192]; |
| |
| return (*cfg & BIT(0)); |
| } |
| #endif |
| |
| #if defined(CONFIG_ARMV8_A_NS) || defined(CONFIG_GIC_SINGLE_SECURITY_STATE) |
| static inline void arm_gic_write_irouter(uint64_t val, unsigned int intid) |
| { |
| mem_addr_t addr = IROUTER(GET_DIST_BASE(intid), intid); |
| |
| #ifdef CONFIG_ARM |
| sys_write32((uint32_t)val, addr); |
| sys_write32((uint32_t)(val >> 32U), addr + 4); |
| #else |
| sys_write64(val, addr); |
| #endif |
| } |
| #endif |
| |
| void arm_gic_irq_set_priority(unsigned int intid, |
| unsigned int prio, uint32_t flags) |
| { |
| #ifdef CONFIG_GIC_V3_ITS |
| if (intid >= 8192) { |
| arm_gic_lpi_set_priority(intid, prio); |
| return; |
| } |
| #endif |
| uint32_t mask = BIT(intid & (GIC_NUM_INTR_PER_REG - 1)); |
| uint32_t idx = intid / GIC_NUM_INTR_PER_REG; |
| uint32_t shift; |
| uint32_t val; |
| mem_addr_t base = GET_DIST_BASE(intid); |
| |
| /* Disable the interrupt */ |
| sys_write32(mask, ICENABLER(base, idx)); |
| gic_wait_rwp(intid); |
| |
| /* PRIORITYR registers provide byte access */ |
| sys_write8(prio & GIC_PRI_MASK, IPRIORITYR(base, intid)); |
| |
| /* Interrupt type config */ |
| if (!GIC_IS_SGI(intid)) { |
| idx = intid / GIC_NUM_CFG_PER_REG; |
| shift = (intid & (GIC_NUM_CFG_PER_REG - 1)) * 2; |
| |
| val = sys_read32(ICFGR(base, idx)); |
| val &= ~(GICD_ICFGR_MASK << shift); |
| if (flags & IRQ_TYPE_EDGE) { |
| val |= (GICD_ICFGR_TYPE << shift); |
| } |
| sys_write32(val, ICFGR(base, idx)); |
| } |
| } |
| |
| void arm_gic_irq_enable(unsigned int intid) |
| { |
| #ifdef CONFIG_GIC_V3_ITS |
| if (intid >= 8192) { |
| arm_gic_lpi_setup(intid, true); |
| return; |
| } |
| #endif |
| uint32_t mask = BIT(intid & (GIC_NUM_INTR_PER_REG - 1)); |
| uint32_t idx = intid / GIC_NUM_INTR_PER_REG; |
| |
| sys_write32(mask, ISENABLER(GET_DIST_BASE(intid), idx)); |
| |
| #if defined(CONFIG_ARMV8_A_NS) || defined(CONFIG_GIC_SINGLE_SECURITY_STATE) |
| /* |
| * Affinity routing is enabled for Armv8-A Non-secure state (GICD_CTLR.ARE_NS |
| * is set to '1') and for GIC single security state (GICD_CTRL.ARE is set to '1'), |
| * so need to set SPI's affinity, now set it to be the PE on which it is enabled. |
| */ |
| if (GIC_IS_SPI(intid)) { |
| arm_gic_write_irouter(MPIDR_TO_CORE(GET_MPIDR()), intid); |
| } |
| #endif |
| } |
| |
| void arm_gic_irq_disable(unsigned int intid) |
| { |
| #ifdef CONFIG_GIC_V3_ITS |
| if (intid >= 8192) { |
| arm_gic_lpi_setup(intid, false); |
| return; |
| } |
| #endif |
| uint32_t mask = BIT(intid & (GIC_NUM_INTR_PER_REG - 1)); |
| uint32_t idx = intid / GIC_NUM_INTR_PER_REG; |
| |
| sys_write32(mask, ICENABLER(GET_DIST_BASE(intid), idx)); |
| /* poll to ensure write is complete */ |
| gic_wait_rwp(intid); |
| } |
| |
| bool arm_gic_irq_is_enabled(unsigned int intid) |
| { |
| #ifdef CONFIG_GIC_V3_ITS |
| if (intid >= 8192) { |
| return arm_gic_lpi_is_enabled(intid); |
| } |
| #endif |
| uint32_t mask = BIT(intid & (GIC_NUM_INTR_PER_REG - 1)); |
| uint32_t idx = intid / GIC_NUM_INTR_PER_REG; |
| uint32_t val; |
| |
| val = sys_read32(ISENABLER(GET_DIST_BASE(intid), idx)); |
| |
| return (val & mask) != 0; |
| } |
| |
| bool arm_gic_irq_is_pending(unsigned int intid) |
| { |
| uint32_t mask = BIT(intid & (GIC_NUM_INTR_PER_REG - 1)); |
| uint32_t idx = intid / GIC_NUM_INTR_PER_REG; |
| uint32_t val; |
| |
| val = sys_read32(ISPENDR(GET_DIST_BASE(intid), idx)); |
| |
| return (val & mask) != 0; |
| } |
| |
| void arm_gic_irq_clear_pending(unsigned int intid) |
| { |
| uint32_t mask = BIT(intid & (GIC_NUM_INTR_PER_REG - 1)); |
| uint32_t idx = intid / GIC_NUM_INTR_PER_REG; |
| |
| sys_write32(mask, ICPENDR(GET_DIST_BASE(intid), idx)); |
| } |
| |
| unsigned int arm_gic_get_active(void) |
| { |
| int intid; |
| |
| /* (Pending -> Active / AP) or (AP -> AP) */ |
| intid = read_sysreg(ICC_IAR1_EL1); |
| |
| return intid; |
| } |
| |
| void arm_gic_eoi(unsigned int intid) |
| { |
| /* |
| * Interrupt request deassertion from peripheral to GIC happens |
| * by clearing interrupt condition by a write to the peripheral |
| * register. It is desired that the write transfer is complete |
| * before the core tries to change GIC state from 'AP/Active' to |
| * a new state on seeing 'EOI write'. |
| * Since ICC interface writes are not ordered against Device |
| * memory writes, a barrier is required to ensure the ordering. |
| * The dsb will also ensure *completion* of previous writes with |
| * DEVICE nGnRnE attribute. |
| */ |
| barrier_dsync_fence_full(); |
| |
| /* (AP -> Pending) Or (Active -> Inactive) or (AP to AP) nested case */ |
| write_sysreg(intid, ICC_EOIR1_EL1); |
| } |
| |
| void gic_raise_sgi(unsigned int sgi_id, uint64_t target_aff, |
| uint16_t target_list) |
| { |
| uint32_t aff3, aff2, aff1; |
| uint64_t sgi_val; |
| |
| __ASSERT_NO_MSG(GIC_IS_SGI(sgi_id)); |
| |
| /* Extract affinity fields from target */ |
| aff1 = MPIDR_AFFLVL(target_aff, 1); |
| aff2 = MPIDR_AFFLVL(target_aff, 2); |
| #if defined(CONFIG_ARM) |
| /* There is no Aff3 in AArch32 MPIDR */ |
| aff3 = 0; |
| #else |
| aff3 = MPIDR_AFFLVL(target_aff, 3); |
| #endif |
| sgi_val = GICV3_SGIR_VALUE(aff3, aff2, aff1, sgi_id, |
| SGIR_IRM_TO_AFF, target_list); |
| |
| barrier_dsync_fence_full(); |
| write_sysreg(sgi_val, ICC_SGI1R); |
| barrier_isync_fence_full(); |
| } |
| |
| /* |
| * Wake up GIC redistributor. |
| * clear ProcessorSleep and wait till ChildAsleep is cleared. |
| * ProcessSleep to be cleared only when ChildAsleep is set |
| * Check if redistributor is not powered already. |
| */ |
| static void gicv3_rdist_enable(mem_addr_t rdist) |
| { |
| if (!(sys_read32(rdist + GICR_WAKER) & BIT(GICR_WAKER_CA))) { |
| return; |
| } |
| |
| if (GICR_IIDR_PRODUCT_ID_GET(sys_read32(rdist + GICR_IIDR)) >= 0x2) { |
| if (sys_read32(rdist + GICR_PWRR) & BIT(GICR_PWRR_RDPD)) { |
| sys_set_bit(rdist + GICR_PWRR, GICR_PWRR_RDAG); |
| sys_clear_bit(rdist + GICR_PWRR, GICR_PWRR_RDPD); |
| while (sys_read32(rdist + GICR_PWRR) & BIT(GICR_PWRR_RDPD)) { |
| ; |
| } |
| } |
| } |
| |
| sys_clear_bit(rdist + GICR_WAKER, GICR_WAKER_PS); |
| while (sys_read32(rdist + GICR_WAKER) & BIT(GICR_WAKER_CA)) { |
| ; |
| } |
| } |
| |
| #ifdef CONFIG_GIC_V3_ITS |
| /* |
| * Setup LPIs Configuration & Pending tables for redistributors |
| * LPI configuration is global, each redistributor has a pending table |
| */ |
| static void gicv3_rdist_setup_lpis(mem_addr_t rdist) |
| { |
| unsigned int lpi_id_bits = MIN(GICD_TYPER_IDBITS(sys_read32(GICD_TYPER)), |
| ITS_MAX_LPI_NRBITS); |
| uintptr_t lpi_pend_table; |
| uint64_t reg; |
| uint32_t ctlr; |
| |
| /* If not, alloc a common prop table for all redistributors */ |
| if (!lpi_prop_table) { |
| lpi_prop_table = (uintptr_t)k_aligned_alloc(4 * 1024, LPI_PROPBASE_SZ(lpi_id_bits)); |
| memset((void *)lpi_prop_table, 0, LPI_PROPBASE_SZ(lpi_id_bits)); |
| } |
| |
| lpi_pend_table = (uintptr_t)k_aligned_alloc(64 * 1024, LPI_PENDBASE_SZ(lpi_id_bits)); |
| memset((void *)lpi_pend_table, 0, LPI_PENDBASE_SZ(lpi_id_bits)); |
| |
| ctlr = sys_read32(rdist + GICR_CTLR); |
| ctlr &= ~GICR_CTLR_ENABLE_LPIS; |
| sys_write32(ctlr, rdist + GICR_CTLR); |
| |
| /* PROPBASE */ |
| reg = (GIC_BASER_SHARE_INNER << GITR_PROPBASER_SHAREABILITY_SHIFT) | |
| (GIC_BASER_CACHE_RAWAWB << GITR_PROPBASER_INNER_CACHE_SHIFT) | |
| (lpi_prop_table & (GITR_PROPBASER_ADDR_MASK << GITR_PROPBASER_ADDR_SHIFT)) | |
| (GIC_BASER_CACHE_INNERLIKE << GITR_PROPBASER_OUTER_CACHE_SHIFT) | |
| ((lpi_id_bits - 1) & GITR_PROPBASER_ID_BITS_MASK); |
| sys_write64(reg, rdist + GICR_PROPBASER); |
| /* TOFIX: check SHAREABILITY validity */ |
| |
| /* PENDBASE */ |
| reg = (GIC_BASER_SHARE_INNER << GITR_PENDBASER_SHAREABILITY_SHIFT) | |
| (GIC_BASER_CACHE_RAWAWB << GITR_PENDBASER_INNER_CACHE_SHIFT) | |
| (lpi_pend_table & (GITR_PENDBASER_ADDR_MASK << GITR_PENDBASER_ADDR_SHIFT)) | |
| (GIC_BASER_CACHE_INNERLIKE << GITR_PENDBASER_OUTER_CACHE_SHIFT) | |
| GITR_PENDBASER_PTZ; |
| sys_write64(reg, rdist + GICR_PENDBASER); |
| /* TOFIX: check SHAREABILITY validity */ |
| |
| ctlr = sys_read32(rdist + GICR_CTLR); |
| ctlr |= GICR_CTLR_ENABLE_LPIS; |
| sys_write32(ctlr, rdist + GICR_CTLR); |
| |
| barrier_dsync_fence_full(); |
| } |
| #endif |
| |
| /* |
| * Initialize the cpu interface. This should be called by each core. |
| */ |
| static void gicv3_cpuif_init(void) |
| { |
| uint32_t icc_sre; |
| uint32_t intid; |
| |
| mem_addr_t base = gic_get_rdist() + GICR_SGI_BASE_OFF; |
| |
| /* Disable all sgi ppi */ |
| sys_write32(BIT64_MASK(GIC_NUM_INTR_PER_REG), ICENABLER(base, 0)); |
| /* Any sgi/ppi intid ie. 0-31 will select GICR_CTRL */ |
| gic_wait_rwp(0); |
| |
| /* Clear pending */ |
| sys_write32(BIT64_MASK(GIC_NUM_INTR_PER_REG), ICPENDR(base, 0)); |
| |
| /* Configure all SGIs/PPIs as G1S or G1NS depending on Zephyr |
| * is run in EL1S or EL1NS respectively. |
| * All interrupts will be delivered as irq |
| */ |
| sys_write32(IGROUPR_VAL, IGROUPR(base, 0)); |
| sys_write32(BIT64_MASK(GIC_NUM_INTR_PER_REG), IGROUPMODR(base, 0)); |
| |
| /* |
| * Configure default priorities for SGI 0:15 and PPI 0:15. |
| */ |
| for (intid = 0; intid < GIC_SPI_INT_BASE; |
| intid += GIC_NUM_PRI_PER_REG) { |
| sys_write32(GIC_INT_DEF_PRI_X4, IPRIORITYR(base, intid)); |
| } |
| |
| /* Configure PPIs as level triggered */ |
| sys_write32(0, ICFGR(base, 1)); |
| |
| /* |
| * Check if system interface can be enabled. |
| * 'icc_sre_el3' needs to be configured at 'EL3' |
| * to allow access to 'icc_sre_el1' at 'EL1' |
| * eg: z_arch_el3_plat_init can be used by platform. |
| */ |
| icc_sre = read_sysreg(ICC_SRE_EL1); |
| |
| if (!(icc_sre & ICC_SRE_ELx_SRE_BIT)) { |
| icc_sre = (icc_sre | ICC_SRE_ELx_SRE_BIT | |
| ICC_SRE_ELx_DIB_BIT | ICC_SRE_ELx_DFB_BIT); |
| write_sysreg(icc_sre, ICC_SRE_EL1); |
| icc_sre = read_sysreg(ICC_SRE_EL1); |
| |
| __ASSERT_NO_MSG(icc_sre & ICC_SRE_ELx_SRE_BIT); |
| } |
| |
| write_sysreg(GIC_IDLE_PRIO, ICC_PMR_EL1); |
| |
| /* Allow group1 interrupts */ |
| write_sysreg(1, ICC_IGRPEN1_EL1); |
| } |
| |
| /* |
| * TODO: Consider Zephyr in EL1NS. |
| */ |
| static void gicv3_dist_init(void) |
| { |
| unsigned int num_ints; |
| unsigned int intid; |
| unsigned int idx; |
| mem_addr_t base = GIC_DIST_BASE; |
| |
| num_ints = sys_read32(GICD_TYPER); |
| num_ints &= GICD_TYPER_ITLINESNUM_MASK; |
| num_ints = (num_ints + 1) << 5; |
| |
| /* Disable the distributor */ |
| sys_write32(0, GICD_CTLR); |
| gic_wait_rwp(GIC_SPI_INT_BASE); |
| #ifdef CONFIG_GIC_SINGLE_SECURITY_STATE |
| /* |
| * Before configuration, we need to check whether |
| * the GIC single security state mode is supported. |
| * Make sure GICD_CTRL_NS is 1. |
| */ |
| sys_set_bit(GICD_CTLR, GICD_CTRL_NS); |
| __ASSERT(sys_test_bit(GICD_CTLR, GICD_CTRL_NS), |
| "Current GIC does not support single security state"); |
| #endif |
| |
| /* |
| * Default configuration of all SPIs |
| */ |
| for (intid = GIC_SPI_INT_BASE; intid < num_ints; |
| intid += GIC_NUM_INTR_PER_REG) { |
| idx = intid / GIC_NUM_INTR_PER_REG; |
| /* Disable interrupt */ |
| sys_write32(BIT64_MASK(GIC_NUM_INTR_PER_REG), |
| ICENABLER(base, idx)); |
| /* Clear pending */ |
| sys_write32(BIT64_MASK(GIC_NUM_INTR_PER_REG), |
| ICPENDR(base, idx)); |
| sys_write32(IGROUPR_VAL, IGROUPR(base, idx)); |
| sys_write32(BIT64_MASK(GIC_NUM_INTR_PER_REG), |
| IGROUPMODR(base, idx)); |
| |
| } |
| /* wait for rwp on GICD */ |
| gic_wait_rwp(GIC_SPI_INT_BASE); |
| |
| /* Configure default priorities for all SPIs. */ |
| for (intid = GIC_SPI_INT_BASE; intid < num_ints; |
| intid += GIC_NUM_PRI_PER_REG) { |
| sys_write32(GIC_INT_DEF_PRI_X4, IPRIORITYR(base, intid)); |
| } |
| |
| /* Configure all SPIs as active low, level triggered by default */ |
| for (intid = GIC_SPI_INT_BASE; intid < num_ints; |
| intid += GIC_NUM_CFG_PER_REG) { |
| idx = intid / GIC_NUM_CFG_PER_REG; |
| sys_write32(0, ICFGR(base, idx)); |
| } |
| |
| #ifdef CONFIG_ARMV8_A_NS |
| /* Enable distributor with ARE */ |
| sys_write32(BIT(GICD_CTRL_ARE_NS) | BIT(GICD_CTLR_ENABLE_G1NS), |
| GICD_CTLR); |
| #elif defined(CONFIG_GIC_SINGLE_SECURITY_STATE) |
| /* |
| * For GIC single security state, the config GIC_SINGLE_SECURITY_STATE |
| * means the GIC is under single security state which has only two |
| * groups: group 0 and group 1. |
| * Then set GICD_CTLR_ARE and GICD_CTLR_ENABLE_G1 to enable Group 1 |
| * interrupt. |
| * Since the GICD_CTLR_ARE and GICD_CTRL_ARE_S share BIT(4), and |
| * similarly the GICD_CTLR_ENABLE_G1 and GICD_CTLR_ENABLE_G1NS share |
| * BIT(1), we can reuse them. |
| */ |
| sys_write32(BIT(GICD_CTRL_ARE_S) | BIT(GICD_CTLR_ENABLE_G1NS), |
| GICD_CTLR); |
| #else |
| /* enable Group 1 secure interrupts */ |
| sys_set_bit(GICD_CTLR, GICD_CTLR_ENABLE_G1S); |
| #endif |
| } |
| |
| static uint64_t arm_gic_mpidr_to_affinity(uint64_t mpidr) |
| { |
| uint64_t aff3, aff2, aff1, aff0; |
| |
| #if defined(CONFIG_ARM) |
| /* There is no Aff3 in AArch32 MPIDR */ |
| aff3 = 0; |
| #else |
| aff3 = MPIDR_AFFLVL(mpidr, 3); |
| #endif |
| |
| aff2 = MPIDR_AFFLVL(mpidr, 2); |
| aff1 = MPIDR_AFFLVL(mpidr, 1); |
| aff0 = MPIDR_AFFLVL(mpidr, 0); |
| |
| return (aff3 << 24 | aff2 << 16 | aff1 << 8 | aff0); |
| } |
| |
| static bool arm_gic_aff_matching(uint64_t gicr_aff, uint64_t aff) |
| { |
| #if defined(CONFIG_GIC_V3_RDIST_MATCHING_AFF0_ONLY) |
| uint64_t mask = BIT64_MASK(8); |
| |
| return (gicr_aff & mask) == (aff & mask); |
| #else |
| return gicr_aff == aff; |
| #endif |
| } |
| |
| static inline uint64_t arm_gic_get_typer(mem_addr_t addr) |
| { |
| uint64_t val; |
| |
| #if defined(CONFIG_ARM) |
| val = sys_read32(addr); |
| val |= (uint64_t)sys_read32(addr + 4) << 32; |
| #else |
| val = sys_read64(addr); |
| #endif |
| |
| return val; |
| } |
| |
| static mem_addr_t arm_gic_iterate_rdists(void) |
| { |
| uint64_t aff = arm_gic_mpidr_to_affinity(GET_MPIDR()); |
| |
| for (mem_addr_t rdist_addr = GIC_RDIST_BASE; |
| rdist_addr < GIC_RDIST_BASE + GIC_RDIST_SIZE; |
| rdist_addr += 0x20000) { |
| uint64_t val = arm_gic_get_typer(rdist_addr + GICR_TYPER); |
| uint64_t gicr_aff = GICR_TYPER_AFFINITY_VALUE_GET(val); |
| |
| if (arm_gic_aff_matching(gicr_aff, aff)) { |
| return rdist_addr; |
| } |
| |
| if (GICR_TYPER_LAST_GET(val) == 1) { |
| return (mem_addr_t)NULL; |
| } |
| } |
| |
| return (mem_addr_t)NULL; |
| } |
| |
| static void __arm_gic_init(void) |
| { |
| uint8_t cpu; |
| mem_addr_t gic_rd_base; |
| |
| cpu = arch_curr_cpu()->id; |
| gic_rd_base = arm_gic_iterate_rdists(); |
| __ASSERT(gic_rd_base != (mem_addr_t)NULL, ""); |
| |
| gic_rdists[cpu] = gic_rd_base; |
| |
| #ifdef CONFIG_GIC_V3_ITS |
| /* Enable LPIs in Redistributor */ |
| gicv3_rdist_setup_lpis(gic_get_rdist()); |
| #endif |
| |
| gicv3_rdist_enable(gic_get_rdist()); |
| |
| gicv3_cpuif_init(); |
| } |
| |
| int arm_gic_init(const struct device *dev) |
| { |
| gicv3_dist_init(); |
| |
| __arm_gic_init(); |
| |
| return 0; |
| } |
| DEVICE_DT_INST_DEFINE(0, arm_gic_init, NULL, NULL, NULL, |
| PRE_KERNEL_1, CONFIG_INTC_INIT_PRIORITY, NULL); |
| |
| #ifdef CONFIG_SMP |
| void arm_gic_secondary_init(void) |
| { |
| __arm_gic_init(); |
| |
| #ifdef CONFIG_GIC_V3_ITS |
| /* Map this CPU Redistributor in all the ITS Collection tables */ |
| its_rdist_map(); |
| #endif |
| } |
| #endif |