| .. zephyr:board:: stm32f030_demo |
| |
| This board has the bare minimum components required to power on |
| the STM32F030F4P6 MCU. Most of the GPIOs on the STM32 SoC have |
| been exposed in the external headers with silk screen labels |
| that match the SoC's pin names. |
| |
| For practical use, you'll need to add additional components |
| and circuits using a breadboard, for example. |
| |
| More information about the board can be found at the `stm32-base.org website`_. |
| |
| More information about STM32F030F4P6 can be found here: |
| |
| - `STM32F030 reference manual`_ |
| - `STM32F030 data sheet`_ |
| |
| Hardware |
| ******** |
| |
| - STM32F030F4P6 ARM Cortex-M0 processor, frequency up to 48 MHz |
| - 16 KiB of flash memory and 4 KiB of RAM |
| - 8 MHz quartz crystal |
| - 1 user LED |
| - One reset button |
| - 2-way jumper (BOOT0) |
| - Serial (1x4 male dupont (2.54mm)) |
| - SWD (1x4 male dupont (2.54mm)) |
| - USB port (power only) |
| |
| Supported Features |
| ================== |
| |
| .. zephyr:board-supported-hw:: |
| |
| Pin Mapping |
| =========== |
| |
| Default Zephyr Peripheral Mapping: |
| ---------------------------------- |
| |
| - UART_1 TX/RX : PA9/PA10 |
| - LED : PA4 |
| |
| Programming and Debugging |
| ************************* |
| |
| .. zephyr:board-supported-runners:: |
| |
| Applications for the ``stm32f030_demo`` board configuration can be built and |
| flashed in the usual way (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Flashing |
| ======== |
| |
| The board can be flashed by using ST-LINKV2 in-circuit debugger and programmer. |
| This interface is supported by the openocd version included in the Zephyr SDK. |
| |
| Flashing an application to STM32F030 DEMO BOARD |
| ----------------------------------------------- |
| |
| Here is an example for the :zephyr:code-sample:`blinky` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/basic/blinky |
| :board: stm32f030_demo |
| :goals: build flash |
| |
| You will see the LED blinking every second. |
| |
| Debugging |
| ========= |
| |
| You can debug an application in the usual way. Here is an example for the |
| :zephyr:code-sample:`blinky` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/basic/blinky |
| :board: stm32f030_demo |
| :maybe-skip-config: |
| :goals: debug |
| |
| References |
| ********** |
| |
| .. target-notes:: |
| |
| .. _stm32-base.org website: |
| https://stm32-base.org/boards/STM32F030F4P6-STM32F030-DEMO-BOARD-V1.1 |
| |
| .. _STM32F030 reference manual: |
| https://www.st.com/resource/en/reference_manual/dm00091010.pdf |
| |
| .. _STM32F030 data sheet: |
| https://www.st.com/resource/en/datasheet/stm32f030f4.pdf |
