blob: 23eb1114ecb04cfc57cc400cfd79dacb5d6c44be [file] [log] [blame]
/*
* Copyright (c) 2019 Manivannan Sadhasivam
* Copyright (c) 2020 Andreas Sandberg
*
* SPDX-License-Identifier: Apache-2.0
*/
#include <drivers/gpio.h>
#include <drivers/lora.h>
#include <drivers/spi.h>
#include <zephyr.h>
#include <sx126x/sx126x.h>
#include "sx12xx_common.h"
#include "sx126x_common.h"
#include <logging/log.h>
LOG_MODULE_REGISTER(sx126x, CONFIG_LORA_LOG_LEVEL);
BUILD_ASSERT(DT_NUM_INST_STATUS_OKAY(semtech_sx1261) +
DT_NUM_INST_STATUS_OKAY(semtech_sx1262) +
DT_NUM_INST_STATUS_OKAY(st_stm32wl_subghz_radio) <= 1,
"Multiple SX126x instances in DT");
#define DIO2_TX_ENABLE DT_INST_PROP(0, dio2_tx_enable)
#define HAVE_DIO3_TCXO DT_INST_NODE_HAS_PROP(0, dio3_tcxo_voltage)
#if HAVE_DIO3_TCXO
#define TCXO_DIO3_VOLTAGE DT_INST_PROP(0, dio3_tcxo_voltage)
#endif
#if DT_INST_NODE_HAS_PROP(0, tcxo_power_startup_delay_ms)
#define TCXO_POWER_STARTUP_DELAY_MS \
DT_INST_PROP(0, tcxo_power_startup_delay_ms)
#else
#define TCXO_POWER_STARTUP_DELAY_MS 0
#endif
#define SX126X_CALIBRATION_ALL 0x7f
static const struct sx126x_config dev_config = {
.bus = SPI_DT_SPEC_INST_GET(0, SPI_WORD_SET(8) | SPI_TRANSFER_MSB, 0),
#if HAVE_GPIO_ANTENNA_ENABLE
.antenna_enable = GPIO_DT_SPEC_INST_GET(0, antenna_enable_gpios),
#endif
#if HAVE_GPIO_TX_ENABLE
.tx_enable = GPIO_DT_SPEC_INST_GET(0, tx_enable_gpios),
#endif
#if HAVE_GPIO_RX_ENABLE
.rx_enable = GPIO_DT_SPEC_INST_GET(0, rx_enable_gpios),
#endif
};
static struct sx126x_data dev_data;
void SX126xWaitOnBusy(void);
#define MODE(m) [MODE_##m] = #m
static const char *const mode_names[] = {
MODE(SLEEP),
MODE(STDBY_RC),
MODE(STDBY_XOSC),
MODE(FS),
MODE(TX),
MODE(RX),
MODE(RX_DC),
MODE(CAD),
};
#undef MODE
static const char *sx126x_mode_name(RadioOperatingModes_t m)
{
static const char *unknown_mode = "unknown";
if (m < ARRAY_SIZE(mode_names) && mode_names[m]) {
return mode_names[m];
} else {
return unknown_mode;
}
}
static int sx126x_spi_transceive(uint8_t *req_tx, uint8_t *req_rx,
size_t req_len, void *data_tx, void *data_rx,
size_t data_len)
{
int ret;
const struct spi_buf tx_buf[] = {
{
.buf = req_tx,
.len = req_len,
},
{
.buf = data_tx,
.len = data_len
}
};
const struct spi_buf rx_buf[] = {
{
.buf = req_rx,
.len = req_len,
},
{
.buf = data_rx,
.len = data_len
}
};
const struct spi_buf_set tx = {
.buffers = tx_buf,
.count = ARRAY_SIZE(tx_buf),
};
const struct spi_buf_set rx = {
.buffers = rx_buf,
.count = ARRAY_SIZE(rx_buf)
};
/* Wake the device if necessary */
SX126xCheckDeviceReady();
if (!req_rx && !data_rx) {
ret = spi_write_dt(&dev_config.bus, &tx);
} else {
ret = spi_transceive_dt(&dev_config.bus, &tx, &rx);
}
if (ret < 0) {
LOG_ERR("SPI transaction failed: %i", ret);
}
if (req_len >= 1 && req_tx[0] != RADIO_SET_SLEEP) {
SX126xWaitOnBusy();
}
return ret;
}
uint8_t SX126xReadRegister(uint16_t address)
{
uint8_t data;
SX126xReadRegisters(address, &data, 1);
return data;
}
void SX126xReadRegisters(uint16_t address, uint8_t *buffer, uint16_t size)
{
uint8_t req[] = {
RADIO_READ_REGISTER,
(address >> 8) & 0xff,
address & 0xff,
0,
};
LOG_DBG("Reading %" PRIu16 " registers @ 0x%" PRIx16, size, address);
sx126x_spi_transceive(req, NULL, sizeof(req), NULL, buffer, size);
LOG_HEXDUMP_DBG(buffer, size, "register_value");
}
void SX126xWriteRegister(uint16_t address, uint8_t value)
{
SX126xWriteRegisters(address, &value, 1);
}
void SX126xWriteRegisters(uint16_t address, uint8_t *buffer, uint16_t size)
{
uint8_t req[] = {
RADIO_WRITE_REGISTER,
(address >> 8) & 0xff,
address & 0xff,
};
LOG_DBG("Writing %" PRIu16 " registers @ 0x%" PRIx16
": 0x%" PRIx8 " , ...",
size, address, buffer[0]);
sx126x_spi_transceive(req, NULL, sizeof(req), buffer, NULL, size);
}
uint8_t SX126xReadCommand(RadioCommands_t opcode,
uint8_t *buffer, uint16_t size)
{
uint8_t tx_req[] = {
opcode,
0x00,
};
uint8_t rx_req[sizeof(tx_req)];
LOG_DBG("Issuing opcode 0x%x (data size: %" PRIx16 ")",
opcode, size);
sx126x_spi_transceive(tx_req, rx_req, sizeof(rx_req),
NULL, buffer, size);
LOG_DBG("-> status: 0x%" PRIx8, rx_req[1]);
return rx_req[1];
}
void SX126xWriteCommand(RadioCommands_t opcode, uint8_t *buffer, uint16_t size)
{
uint8_t req[] = {
opcode,
};
LOG_DBG("Issuing opcode 0x%x w. %" PRIu16 " bytes of data",
opcode, size);
sx126x_spi_transceive(req, NULL, sizeof(req), buffer, NULL, size);
}
void SX126xReadBuffer(uint8_t offset, uint8_t *buffer, uint8_t size)
{
uint8_t req[] = {
RADIO_READ_BUFFER,
offset,
0x00,
};
LOG_DBG("Reading buffers @ 0x%" PRIx8 " (%" PRIu8 " bytes)",
offset, size);
sx126x_spi_transceive(req, NULL, sizeof(req), NULL, buffer, size);
}
void SX126xWriteBuffer(uint8_t offset, uint8_t *buffer, uint8_t size)
{
uint8_t req[] = {
RADIO_WRITE_BUFFER,
offset,
};
LOG_DBG("Writing buffers @ 0x%" PRIx8 " (%" PRIu8 " bytes)",
offset, size);
sx126x_spi_transceive(req, NULL, sizeof(req), buffer, NULL, size);
}
void SX126xAntSwOn(void)
{
#if HAVE_GPIO_ANTENNA_ENABLE
LOG_DBG("Enabling antenna switch");
gpio_pin_set_dt(&dev_config.antenna_enable, 1);
#else
LOG_DBG("No antenna switch configured");
#endif
}
void SX126xAntSwOff(void)
{
#if HAVE_GPIO_ANTENNA_ENABLE
LOG_DBG("Disabling antenna switch");
gpio_pin_set_dt(&dev_config.antenna_enable, 0);
#else
LOG_DBG("No antenna switch configured");
#endif
}
static void sx126x_set_tx_enable(int value)
{
#if HAVE_GPIO_TX_ENABLE
gpio_pin_set_dt(&dev_config.tx_enable, value);
#endif
}
static void sx126x_set_rx_enable(int value)
{
#if HAVE_GPIO_RX_ENABLE
gpio_pin_set_dt(&dev_config.rx_enable, value);
#endif
}
RadioOperatingModes_t SX126xGetOperatingMode(void)
{
return dev_data.mode;
}
void SX126xSetOperatingMode(RadioOperatingModes_t mode)
{
LOG_DBG("SetOperatingMode: %s (%i)", sx126x_mode_name(mode), mode);
dev_data.mode = mode;
/* To avoid inadvertently putting the RF switch in an
* undefined state, first disable the port we don't want to
* use and then enable the other one.
*/
switch (mode) {
case MODE_TX:
sx126x_set_rx_enable(0);
sx126x_set_tx_enable(1);
break;
case MODE_RX:
case MODE_RX_DC:
case MODE_CAD:
sx126x_set_tx_enable(0);
sx126x_set_rx_enable(1);
break;
case MODE_SLEEP:
/* Additionally disable the DIO1 interrupt to save power */
sx126x_dio1_irq_disable(&dev_data);
__fallthrough;
default:
sx126x_set_rx_enable(0);
sx126x_set_tx_enable(0);
break;
}
}
uint32_t SX126xGetBoardTcxoWakeupTime(void)
{
return TCXO_POWER_STARTUP_DELAY_MS;
}
uint8_t SX126xGetDeviceId(void)
{
return SX126X_DEVICE_ID;
}
void SX126xIoIrqInit(DioIrqHandler dioIrq)
{
LOG_DBG("Configuring DIO IRQ callback");
dev_data.radio_dio_irq = dioIrq;
}
void SX126xIoTcxoInit(void)
{
#if HAVE_DIO3_TCXO
CalibrationParams_t cal = {
.Value = SX126X_CALIBRATION_ALL,
};
LOG_DBG("TCXO on DIO3");
/* Delay in units of 15.625 us (1/64 ms) */
SX126xSetDio3AsTcxoCtrl(TCXO_DIO3_VOLTAGE,
TCXO_POWER_STARTUP_DELAY_MS << 6);
SX126xCalibrate(cal);
#else
LOG_DBG("No TCXO configured");
#endif
}
void SX126xIoRfSwitchInit(void)
{
LOG_DBG("Configuring DIO2");
SX126xSetDio2AsRfSwitchCtrl(DIO2_TX_ENABLE);
}
void SX126xReset(void)
{
LOG_DBG("Resetting radio");
sx126x_reset(&dev_data);
/* Device transitions to standby on reset */
dev_data.mode = MODE_STDBY_RC;
}
void SX126xSetRfTxPower(int8_t power)
{
LOG_DBG("power: %" PRIi8, power);
SX126xSetTxParams(power, RADIO_RAMP_40_US);
}
void SX126xWaitOnBusy(void)
{
while (sx126x_is_busy(&dev_data)) {
k_sleep(K_MSEC(1));
}
}
void SX126xWakeup(void)
{
int ret;
/* Reenable DIO1 when waking up */
sx126x_dio1_irq_enable(&dev_data);
uint8_t req[] = { RADIO_GET_STATUS, 0 };
const struct spi_buf tx_buf = {
.buf = req,
.len = sizeof(req),
};
const struct spi_buf_set tx = {
.buffers = &tx_buf,
.count = 1,
};
LOG_DBG("Sending GET_STATUS");
ret = spi_write_dt(&dev_config.bus, &tx);
if (ret < 0) {
LOG_ERR("SPI transaction failed: %i", ret);
return;
}
LOG_DBG("Waiting for device...");
SX126xWaitOnBusy();
LOG_DBG("Device ready");
/* This function is only called from sleep mode
* All edges on the SS SPI pin will transition the modem to
* standby mode (via startup)
*/
dev_data.mode = MODE_STDBY_RC;
}
uint32_t SX126xGetDio1PinState(void)
{
return sx126x_get_dio1_pin_state(&dev_data);
}
static void sx126x_dio1_irq_work_handler(struct k_work *work)
{
LOG_DBG("Processing DIO1 interrupt");
if (!dev_data.radio_dio_irq) {
LOG_WRN("DIO1 interrupt without valid HAL IRQ callback.");
return;
}
dev_data.radio_dio_irq(NULL);
if (Radio.IrqProcess) {
Radio.IrqProcess();
}
/* Re-enable the interrupt if we are not in sleep mode */
if (dev_data.mode != MODE_SLEEP) {
sx126x_dio1_irq_enable(&dev_data);
}
}
static int sx126x_lora_init(const struct device *dev)
{
const struct sx126x_config *config = dev->config;
int ret;
LOG_DBG("Initializing %s", DT_INST_LABEL(0));
if (sx12xx_configure_pin(antenna_enable, GPIO_OUTPUT_INACTIVE) ||
sx12xx_configure_pin(rx_enable, GPIO_OUTPUT_INACTIVE) ||
sx12xx_configure_pin(tx_enable, GPIO_OUTPUT_INACTIVE)) {
return -EIO;
}
k_work_init(&dev_data.dio1_irq_work, sx126x_dio1_irq_work_handler);
ret = sx126x_variant_init(dev);
if (ret) {
LOG_ERR("Variant initialization failed");
return ret;
}
if (!spi_is_ready(&config->bus)) {
LOG_ERR("SPI device not ready");
return -ENODEV;
}
ret = sx12xx_init(dev);
if (ret < 0) {
LOG_ERR("Failed to initialize SX12xx common");
return ret;
}
return 0;
}
static const struct lora_driver_api sx126x_lora_api = {
.config = sx12xx_lora_config,
.send = sx12xx_lora_send,
.send_async = sx12xx_lora_send_async,
.recv = sx12xx_lora_recv,
.recv_async = sx12xx_lora_recv_async,
.test_cw = sx12xx_lora_test_cw,
};
DEVICE_DT_INST_DEFINE(0, &sx126x_lora_init, NULL, &dev_data,
&dev_config, POST_KERNEL, CONFIG_LORA_INIT_PRIORITY,
&sx126x_lora_api);