| .. _frdm_k64f: |
| |
| NXP FRDM-K64F |
| ############## |
| |
| Overview |
| ******** |
| |
| The Freedom-K64F is an ultra-low-cost development platform for Kinetis K64, |
| K63, and K24 MCUs. |
| |
| - Form-factor compatible with the Arduino R3 pin layout |
| - Peripherals enable rapid prototyping, including a 6-axis digital |
| accelerometer and magnetometer to create full eCompass capabilities, a |
| tri-colored LED and 2 user push-buttons for direct interaction, a microSD |
| card slot, and connectivity using onboard Ethernet port and headers for use |
| with Bluetooth* and 2.4 GHz radio add-on modules |
| - OpenSDAv2, the NXP open source hardware embedded serial and debug adapter |
| running an open source bootloader, offers options for serial communication, |
| flash programming, and run-control debugging |
| |
| .. image:: frdm_k64f.jpg |
| :width: 720px |
| :align: center |
| :alt: FRDM-K64F |
| |
| Hardware |
| ******** |
| |
| - MK64FN1M0VLL12 MCU (120 MHz, 1 MB flash memory, 256 KB RAM, low-power, |
| crystal-less USB, and 100 Low profile Quad Flat Package (LQFP)) |
| - Dual role USB interface with micro-B USB connector |
| - RGB LED |
| - FXOS8700CQ accelerometer and magnetometer |
| - Two user push buttons |
| - Flexible power supply option - OpenSDAv2 USB, Kinetis K64 USB, and external source |
| - Easy access to MCU input/output through Arduino* R3 compatible I/O connectors |
| - Programmable OpenSDAv2 debug circuit supporting the CMSIS-DAP Interface |
| software that provides: |
| |
| - Mass storage device (MSD) flash programming interface |
| - CMSIS-DAP debug interface over a driver-less USB HID connection providing |
| run-control debugging and compatibility with IDE tools |
| - Virtual serial port interface |
| - Open source CMSIS-DAP software project |
| |
| - Ethernet |
| - SDHC |
| |
| For more information about the K64F SoC and FRDM-K64F board: |
| |
| - `K64F Website`_ |
| - `K64F Datasheet`_ |
| - `K64F Reference Manual`_ |
| - `FRDM-K64F Website`_ |
| - `FRDM-K64F User Guide`_ |
| - `FRDM-K64F Schematics`_ |
| |
| Supported Features |
| ================== |
| |
| The frdm_k64f board configuration supports the following hardware features: |
| |
| +-----------+------------+-------------------------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+=====================================+ |
| | NVIC | on-chip | nested vector interrupt controller | |
| +-----------+------------+-------------------------------------+ |
| | SYSTICK | on-chip | systick | |
| +-----------+------------+-------------------------------------+ |
| | PINMUX | on-chip | pinmux | |
| +-----------+------------+-------------------------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+-------------------------------------+ |
| | I2C | on-chip | i2c | |
| +-----------+------------+-------------------------------------+ |
| | SPI | on-chip | spi | |
| +-----------+------------+-------------------------------------+ |
| | ADC | on-chip | adc | |
| +-----------+------------+-------------------------------------+ |
| | PWM | on-chip | pwm | |
| +-----------+------------+-------------------------------------+ |
| | ETHERNET | on-chip | ethernet | |
| +-----------+------------+-------------------------------------+ |
| | UART | on-chip | serial port-polling; | |
| | | | serial port-interrupt | |
| +-----------+------------+-------------------------------------+ |
| | FLASH | on-chip | soc flash | |
| +-----------+------------+-------------------------------------+ |
| | SENSOR | off-chip | fxos8700 polling; | |
| | | | fxos8700 trigger | |
| +-----------+------------+-------------------------------------+ |
| |
| The default configuration can be found in the defconfig file: |
| |
| ``boards/arm/frdm_k64f/frdm_k64f_defconfig`` |
| |
| Other hardware features are not currently supported by the port. |
| |
| Connections and IOs |
| =================== |
| |
| The K64F SoC has five pairs of pinmux/gpio controllers. |
| |
| +-------+-----------------+---------------------------+ |
| | Name | Function | Usage | |
| +=======+=================+===========================+ |
| | PTB22 | GPIO | Red LED | |
| +-------+-----------------+---------------------------+ |
| | PTE26 | GPIO | Green LED | |
| +-------+-----------------+---------------------------+ |
| | PTB21 | GPIO | Blue LED | |
| +-------+-----------------+---------------------------+ |
| | PTC6 | GPIO | SW2 / FXOS8700 INT1 | |
| +-------+-----------------+---------------------------+ |
| | PTC13 | GPIO | FXOS8700 INT2 | |
| +-------+-----------------+---------------------------+ |
| | PTA4 | GPIO | SW3 | |
| +-------+-----------------+---------------------------+ |
| | PTB10 | ADC | ADC1 channel 14 | |
| +-------+-----------------+---------------------------+ |
| | PTB16 | UART0_RX | UART Console | |
| +-------+-----------------+---------------------------+ |
| | PTB17 | UART0_TX | UART Console | |
| +-------+-----------------+---------------------------+ |
| | PTC8 | PWM | PWM_3 channel 4 | |
| +-------+-----------------+---------------------------+ |
| | PTC9 | PWM | PWM_3 channel 5 | |
| +-------+-----------------+---------------------------+ |
| | PTC16 | UART3_RX | UART BT HCI | |
| +-------+-----------------+---------------------------+ |
| | PTC17 | UART3_TX | UART BT HCI | |
| +-------+-----------------+---------------------------+ |
| | PTCD0 | SPI0_PCS0 | SPI | |
| +-------+-----------------+---------------------------+ |
| | PTCD1 | SPI0_SCK | SPI | |
| +-------+-----------------+---------------------------+ |
| | PTCD2 | SPI0_SOUT | SPI | |
| +-------+-----------------+---------------------------+ |
| | PTCD3 | SPI0_SIN | SPI | |
| +-------+-----------------+---------------------------+ |
| | PTE24 | I2C0_SCL | I2C / FXOS8700 | |
| +-------+-----------------+---------------------------+ |
| | PTE25 | I2C0_SDA | I2C / FXOS8700 | |
| +-------+-----------------+---------------------------+ |
| | PTA5 | MII0_RXER | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA12 | MII0_RXD1 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA13 | MII0_RXD0 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA14 | MII0_RXDV | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA15 | MII0_TXEN | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA16 | MII0_TXD0 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA17 | MII0_TXD1 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTA28 | MII0_TXER | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTB0 | MII0_MDIO | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTB1 | MII0_MDC | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTC16 | ENET0_1588_TMR0 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTC17 | ENET0_1588_TMR1 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTC18 | ENET0_1588_TMR2 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| | PTC19 | ENET0_1588_TMR3 | Ethernet | |
| +-------+-----------------+---------------------------+ |
| |
| .. note:: |
| Do not enable Ethernet and UART BT HCI simultaneously because they conflict |
| on PTC16-17. |
| |
| System Clock |
| ============ |
| |
| The K64F SoC is configured to use the 50 MHz external oscillator on the board |
| with the on-chip PLL to generate a 120 MHz system clock. |
| |
| Serial Port |
| =========== |
| |
| The K64F SoC has six UARTs. One is configured for the console, another for BT |
| HCI, and the remaining are not used. |
| |
| Programming and Debugging |
| ************************* |
| |
| The FRDM-K64F includes the :ref:`nxp_opensda` serial and debug adapter built |
| into the board to provide debugging, flash programming, and serial |
| communication over USB. |
| |
| To use the pyOCD tools with OpenSDA, follow the instructions in the |
| :ref:`nxp_opensda_pyocd` page using the `DAPLink FRDM-K64F Firmware`_. The |
| pyOCD tools are the default for this board, therefore it is not necessary to |
| set ``OPENSDA_FW=daplink`` explicitly when using the default flash and debug |
| mechanisms. |
| |
| With these mechanisms, applications for the ``frdm_k64f`` board |
| configuration can be built and flashed in the usual way (see |
| :ref:`build_an_application` and :ref:`application_run` for more |
| details). |
| |
| To use the Segger J-Link tools with OpenSDA, follow the instructions in the |
| :ref:`nxp_opensda_jlink` page using the `Segger J-Link OpenSDA V2.1 Firmware`_. |
| The Segger J-Link tools are not the default for this board, therefore it is |
| necessary to set ``OPENSDA_FW=jlink`` explicitly in the environment before |
| programming and debugging. |
| |
| Flashing |
| ======== |
| |
| This example uses the :ref:`hello_world` sample with the |
| :ref:`nxp_opensda_pyocd` tools. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: frdm_k64f |
| :goals: flash |
| |
| Open a serial terminal (minicom, putty, etc.) with the following settings: |
| |
| - Speed: 115200 |
| - Data: 8 bits |
| - Parity: None |
| - Stop bits: 1 |
| |
| Reset the board and you should be able to see on the corresponding Serial Port |
| the following message: |
| |
| .. code-block:: console |
| |
| Hello World! arm |
| |
| Debugging |
| ========= |
| |
| You can debug an application in the usual way. Here is an example for the |
| :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: frdm_k64f |
| :maybe-skip-config: |
| :goals: debug |
| |
| .. _FRDM-K64F Website: |
| http://www.nxp.com/products/software-and-tools/hardware-development-tools/freedom-development-boards/freedom-development-platform-for-kinetis-k64-k63-and-k24-mcus:FRDM-K64F |
| |
| .. _FRDM-K64F User Guide: |
| http://www.nxp.com/assets/documents/data/en/user-guides/FRDMK64FUG.pdf |
| |
| .. _FRDM-K64F Schematics: |
| http://www.nxp.com/assets/downloads/data/en/schematics/FRDM-K64F-SCH-E4.pdf |
| |
| .. _K64F Website: |
| http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/kinetis-cortex-m-mcus/k-series-performance-m4/k6x-ethernet/kinetis-k64-120-mhz-256kb-sram-microcontrollers-mcus-based-on-arm-cortex-m4-core:K64_120 |
| |
| .. _K64F Datasheet: |
| http://www.nxp.com/assets/documents/data/en/data-sheets/K64P144M120SF5.pdf |
| |
| .. _K64F Reference Manual: |
| http://www.nxp.com/assets/documents/data/en/reference-manuals/K64P144M120SF5RM.pdf |
| |
| .. _DAPLink FRDM-K64F Firmware: |
| http://www.nxp.com/assets/downloads/data/en/ide-debug-compile-build-tools/OpenSDAv2.2_DAPLink_frdmk64f_rev0242.zip |
| |
| .. _Segger J-Link OpenSDA V2.1 Firmware: |
| https://www.segger.com/downloads/jlink/OpenSDA_V2_1.bin |