/** | |
****************************************************************************** | |
* @file stm32f0xx_hal_usart.c | |
* @author MCD Application Team | |
* @brief USART HAL module driver. | |
* This file provides firmware functions to manage the following | |
* functionalities of the Universal Synchronous Asynchronous Receiver Transmitter | |
* Peripheral (USART). | |
* + Initialization and de-initialization functions | |
* + IO operation functions | |
* + Peripheral Control functions | |
* + Peripheral State and Error functions | |
* | |
@verbatim | |
=============================================================================== | |
##### How to use this driver ##### | |
=============================================================================== | |
[..] | |
The USART HAL driver can be used as follows: | |
(#) Declare a USART_HandleTypeDef handle structure (eg. USART_HandleTypeDef husart). | |
(#) Initialize the USART low level resources by implementing the HAL_USART_MspInit() API: | |
(++) Enable the USARTx interface clock. | |
(++) USART pins configuration: | |
(+++) Enable the clock for the USART GPIOs. | |
(+++) Configure these USART pins as alternate function pull-up. | |
(++) NVIC configuration if you need to use interrupt process (HAL_USART_Transmit_IT(), | |
HAL_USART_Receive_IT() and HAL_USART_TransmitReceive_IT() APIs): | |
(+++) Configure the USARTx interrupt priority. | |
(+++) Enable the NVIC USART IRQ handle. | |
(++) USART interrupts handling: | |
-@@- The specific USART interrupts (Transmission complete interrupt, | |
RXNE interrupt and Error Interrupts) will be managed using the macros | |
__HAL_USART_ENABLE_IT() and __HAL_USART_DISABLE_IT() inside the transmit and receive process. | |
(++) DMA Configuration if you need to use DMA process (HAL_USART_Transmit_DMA() | |
HAL_USART_Receive_DMA() and HAL_USART_TransmitReceive_DMA() APIs): | |
(+++) Declare a DMA handle structure for the Tx/Rx channel. | |
(+++) Enable the DMAx interface clock. | |
(+++) Configure the declared DMA handle structure with the required Tx/Rx parameters. | |
(+++) Configure the DMA Tx/Rx channel. | |
(+++) Associate the initialized DMA handle to the USART DMA Tx/Rx handle. | |
(+++) Configure the priority and enable the NVIC for the transfer complete interrupt on the DMA Tx/Rx channel. | |
(#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware | |
flow control and Mode (Receiver/Transmitter) in the husart handle Init structure. | |
(#) Initialize the USART registers by calling the HAL_USART_Init() API: | |
(++) This API configures also the low level Hardware GPIO, CLOCK, CORTEX...etc) | |
by calling the customized HAL_USART_MspInit(&husart) API. | |
(#) Three operation modes are available within this driver : | |
*** Polling mode IO operation *** | |
================================= | |
[..] | |
(+) Send an amount of data in blocking mode using HAL_USART_Transmit() | |
(+) Receive an amount of data in blocking mode using HAL_USART_Receive() | |
*** Interrupt mode IO operation *** | |
=================================== | |
[..] | |
(+) Send an amount of data in non blocking mode using HAL_USART_Transmit_IT() | |
(+) At transmission end of half transfer HAL_USART_TxHalfCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_TxHalfCpltCallback | |
(+) At transmission end of transfer HAL_USART_TxCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_TxCpltCallback | |
(+) Receive an amount of data in non blocking mode using HAL_USART_Receive_IT() | |
(+) At reception end of half transfer HAL_USART_RxHalfCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_RxHalfCpltCallback | |
(+) At reception end of transfer HAL_USART_RxCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_RxCpltCallback | |
(+) In case of transfer Error, HAL_USART_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_USART_ErrorCallback | |
*** DMA mode IO operation *** | |
============================== | |
[..] | |
(+) Send an amount of data in non blocking mode (DMA) using HAL_USART_Transmit_DMA() | |
(+) At transmission end of half transfer HAL_USART_TxHalfCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_TxHalfCpltCallback | |
(+) At transmission end of transfer HAL_USART_TxCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_TxCpltCallback | |
(+) Receive an amount of data in non blocking mode (DMA) using HAL_USART_Receive_DMA() | |
(+) At reception end of half transfer HAL_USART_RxHalfCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_RxHalfCpltCallback | |
(+) At reception end of transfer HAL_USART_RxCpltCallback is executed and user can | |
add his own code by customization of function pointer HAL_USART_RxCpltCallback | |
(+) In case of transfer Error, HAL_USART_ErrorCallback() function is executed and user can | |
add his own code by customization of function pointer HAL_USART_ErrorCallback | |
(+) Pause the DMA Transfer using HAL_USART_DMAPause() | |
(+) Resume the DMA Transfer using HAL_USART_DMAResume() | |
(+) Stop the DMA Transfer using HAL_USART_DMAStop() | |
*** USART HAL driver macros list *** | |
============================================= | |
[..] | |
Below the list of most used macros in USART HAL driver. | |
(+) __HAL_USART_ENABLE: Enable the USART peripheral | |
(+) __HAL_USART_DISABLE: Disable the USART peripheral | |
(+) __HAL_USART_GET_FLAG : Check whether the specified USART flag is set or not | |
(+) __HAL_USART_CLEAR_FLAG : Clear the specified USART pending flag | |
(+) __HAL_USART_ENABLE_IT: Enable the specified USART interrupt | |
(+) __HAL_USART_DISABLE_IT: Disable the specified USART interrupt | |
[..] | |
(@) You can refer to the USART HAL driver header file for more useful macros | |
[..] | |
(@) To configure and enable/disable the USART to wake up the MCU from stop mode, resort to UART API's | |
HAL_UARTEx_StopModeWakeUpSourceConfig(), HAL_UARTEx_EnableStopMode() and | |
HAL_UARTEx_DisableStopMode() in casting the USART handle to UART type UART_HandleTypeDef. | |
@endverbatim | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "stm32f0xx_hal.h" | |
/** @addtogroup STM32F0xx_HAL_Driver | |
* @{ | |
*/ | |
/** @defgroup USART USART | |
* @brief HAL USART Synchronous module driver | |
* @{ | |
*/ | |
#ifdef HAL_USART_MODULE_ENABLED | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/** @defgroup USART_Private_Constants USART Private Constants | |
* @{ | |
*/ | |
#define USART_DUMMY_DATA ((uint16_t) 0xFFFFU) /*!< USART transmitted dummy data */ | |
#define USART_TEACK_REACK_TIMEOUT ( 1000U) /*!< USART TX or RX enable acknowledge time-out value */ | |
#define USART_CR1_FIELDS ((uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | \ | |
USART_CR1_TE | USART_CR1_RE | USART_CR1_OVER8)) /*!< USART CR1 fields of parameters set by USART_SetConfig API */ | |
#define USART_CR2_FIELDS ((uint32_t)(USART_CR2_CPHA | USART_CR2_CPOL | \ | |
USART_CR2_CLKEN | USART_CR2_LBCL | USART_CR2_STOP)) /*!< USART CR2 fields of parameters set by USART_SetConfig API */ | |
/** | |
* @} | |
*/ | |
/* Private macros ------------------------------------------------------------*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/** @addtogroup USART_Private_Functions | |
* @{ | |
*/ | |
static void USART_EndTransfer(USART_HandleTypeDef *husart); | |
static void USART_DMATransmitCplt(DMA_HandleTypeDef *hdma); | |
static void USART_DMAReceiveCplt(DMA_HandleTypeDef *hdma); | |
static void USART_DMATxHalfCplt(DMA_HandleTypeDef *hdma); | |
static void USART_DMARxHalfCplt(DMA_HandleTypeDef *hdma); | |
static void USART_DMAError(DMA_HandleTypeDef *hdma); | |
static void USART_DMAAbortOnError(DMA_HandleTypeDef *hdma); | |
static void USART_DMATxAbortCallback(DMA_HandleTypeDef *hdma); | |
static void USART_DMARxAbortCallback(DMA_HandleTypeDef *hdma); | |
static HAL_StatusTypeDef USART_WaitOnFlagUntilTimeout(USART_HandleTypeDef *husart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout); | |
static HAL_StatusTypeDef USART_SetConfig(USART_HandleTypeDef *husart); | |
static HAL_StatusTypeDef USART_CheckIdleState(USART_HandleTypeDef *husart); | |
static HAL_StatusTypeDef USART_Transmit_IT(USART_HandleTypeDef *husart); | |
static HAL_StatusTypeDef USART_EndTransmit_IT(USART_HandleTypeDef *husart); | |
static HAL_StatusTypeDef USART_Receive_IT(USART_HandleTypeDef *husart); | |
static HAL_StatusTypeDef USART_TransmitReceive_IT(USART_HandleTypeDef *husart); | |
/** | |
* @} | |
*/ | |
/* Exported functions --------------------------------------------------------*/ | |
/** @defgroup USART_Exported_Functions USART Exported Functions | |
* @{ | |
*/ | |
/** @defgroup USART_Exported_Functions_Group1 Initialization and de-initialization functions | |
* @brief Initialization and Configuration functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Initialization and Configuration functions ##### | |
=============================================================================== | |
[..] | |
This subsection provides a set of functions allowing to initialize the USART | |
in asynchronous and in synchronous modes. | |
(+) For the asynchronous mode only these parameters can be configured: | |
(++) Baud Rate | |
(++) Word Length | |
(++) Stop Bit | |
(++) Parity | |
(++) USART polarity | |
(++) USART phase | |
(++) USART LastBit | |
(++) Receiver/transmitter modes | |
[..] | |
The HAL_USART_Init() function follows the USART synchronous configuration | |
procedure (details for the procedure are available in reference manual). | |
@endverbatim | |
* @{ | |
*/ | |
/* | |
Additional Table: If the parity is enabled, then the MSB bit of the data written | |
in the data register is transmitted but is changed by the parity bit. | |
According to device capability (support or not of 7-bit word length), | |
frame length is either defined by the M bit (8-bits or 9-bits) | |
or by the M1 and M0 bits (7-bit, 8-bit or 9-bit). | |
Possible USART frame formats are as listed in the following table: | |
Table 1. USART frame format. | |
+-----------------------------------------------------------------------+ | |
| M bit | PCE bit | USART frame | | |
|-------------------|-----------|---------------------------------------| | |
| 0 | 0 | | SB | 8-bit data | STB | | | |
|-------------------|-----------|---------------------------------------| | |
| 0 | 1 | | SB | 7-bit data | PB | STB | | | |
|-------------------|-----------|---------------------------------------| | |
| 1 | 0 | | SB | 9-bit data | STB | | | |
|-------------------|-----------|---------------------------------------| | |
| 1 | 1 | | SB | 8-bit data | PB | STB | | | |
+-----------------------------------------------------------------------+ | |
| M1 bit | M0 bit | PCE bit | USART frame | | |
|---------|---------|-----------|---------------------------------------| | |
| 0 | 0 | 0 | | SB | 8 bit data | STB | | | |
|---------|---------|-----------|---------------------------------------| | |
| 0 | 0 | 1 | | SB | 7 bit data | PB | STB | | | |
|---------|---------|-----------|---------------------------------------| | |
| 0 | 1 | 0 | | SB | 9 bit data | STB | | | |
|---------|---------|-----------|---------------------------------------| | |
| 0 | 1 | 1 | | SB | 8 bit data | PB | STB | | | |
|---------|---------|-----------|---------------------------------------| | |
| 1 | 0 | 0 | | SB | 7 bit data | STB | | | |
|---------|---------|-----------|---------------------------------------| | |
| 1 | 0 | 1 | | SB | 6 bit data | PB | STB | | | |
+-----------------------------------------------------------------------+ | |
*/ | |
/** | |
* @brief Initialize the USART mode according to the specified | |
* parameters in the USART_InitTypeDef and initialize the associated handle. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Init(USART_HandleTypeDef *husart) | |
{ | |
/* Check the USART handle allocation */ | |
if(husart == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check the parameters */ | |
assert_param(IS_USART_INSTANCE(husart->Instance)); | |
if(husart->State == HAL_USART_STATE_RESET) | |
{ | |
/* Allocate lock resource and initialize it */ | |
husart->Lock = HAL_UNLOCKED; | |
/* Init the low level hardware : GPIO, CLOCK */ | |
HAL_USART_MspInit(husart); | |
} | |
husart->State = HAL_USART_STATE_BUSY; | |
/* Disable the Peripheral */ | |
__HAL_USART_DISABLE(husart); | |
/* Set the Usart Communication parameters */ | |
if (USART_SetConfig(husart) == HAL_ERROR) | |
{ | |
return HAL_ERROR; | |
} | |
/* In Synchronous mode, the following bits must be kept cleared: | |
- LINEN bit (if LIN is supported) in the USART_CR2 register | |
- SCEN (if Smartcard is supported), HDSEL and IREN (if IrDA is supported) bits in the USART_CR3 register. */ | |
#if defined (USART_CR2_LINEN) | |
husart->Instance->CR2 &= ~USART_CR2_LINEN; | |
#endif | |
#if defined (USART_CR3_SCEN) | |
#if defined (USART_CR3_IREN) | |
husart->Instance->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN); | |
#else | |
husart->Instance->CR3 &= ~(USART_CR3_SCEN | USART_CR3_HDSEL); | |
#endif | |
#else | |
#if defined (USART_CR3_IREN) | |
husart->Instance->CR3 &= ~(USART_CR3_HDSEL | USART_CR3_IREN); | |
#else | |
husart->Instance->CR3 &= ~(USART_CR3_HDSEL); | |
#endif | |
#endif | |
/* Enable the Peripheral */ | |
__HAL_USART_ENABLE(husart); | |
/* TEACK and/or REACK to check before moving husart->State to Ready */ | |
return (USART_CheckIdleState(husart)); | |
} | |
/** | |
* @brief DeInitialize the USART peripheral. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_DeInit(USART_HandleTypeDef *husart) | |
{ | |
/* Check the USART handle allocation */ | |
if(husart == NULL) | |
{ | |
return HAL_ERROR; | |
} | |
/* Check the parameters */ | |
assert_param(IS_USART_INSTANCE(husart->Instance)); | |
husart->State = HAL_USART_STATE_BUSY; | |
husart->Instance->CR1 = 0x0U; | |
husart->Instance->CR2 = 0x0U; | |
husart->Instance->CR3 = 0x0U; | |
/* DeInit the low level hardware */ | |
HAL_USART_MspDeInit(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_RESET; | |
/* Process Unlock */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
/** | |
* @brief Initialize the USART MSP. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_MspInit(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_MspInit can be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief DeInitialize the USART MSP. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_MspDeInit(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_MspDeInit can be implemented in the user file | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup USART_Exported_Functions_Group2 IO operation functions | |
* @brief USART Transmit and Receive functions | |
* | |
@verbatim | |
=============================================================================== | |
##### IO operation functions ##### | |
=============================================================================== | |
[..] This subsection provides a set of functions allowing to manage the USART synchronous | |
data transfers. | |
[..] The USART supports master mode only: it cannot receive or send data related to an input | |
clock (SCLK is always an output). | |
(#) There are two modes of transfer: | |
(++) Blocking mode: The communication is performed in polling mode. | |
The HAL status of all data processing is returned by the same function | |
after finishing transfer. | |
(++) No-Blocking mode: The communication is performed using Interrupts | |
or DMA, These APIs return the HAL status. | |
The end of the data processing will be indicated through the | |
dedicated USART IRQ when using Interrupt mode or the DMA IRQ when | |
using DMA mode. | |
The HAL_USART_TxCpltCallback(), HAL_USART_RxCpltCallback() and HAL_USART_TxRxCpltCallback() user callbacks | |
will be executed respectively at the end of the transmit or Receive process | |
The HAL_USART_ErrorCallback()user callback will be executed when a communication error is detected | |
(#) Blocking mode APIs are : | |
(++) HAL_USART_Transmit()in simplex mode | |
(++) HAL_USART_Receive() in full duplex receive only | |
(++) HAL_USART_TransmitReceive() in full duplex mode | |
(#) No-Blocking mode APIs with Interrupt are : | |
(++) HAL_USART_Transmit_IT()in simplex mode | |
(++) HAL_USART_Receive_IT() in full duplex receive only | |
(++) HAL_USART_TransmitReceive_IT()in full duplex mode | |
(++) HAL_USART_IRQHandler() | |
(#) No-Blocking mode APIs with DMA are : | |
(++) HAL_USART_Transmit_DMA()in simplex mode | |
(++) HAL_USART_Receive_DMA() in full duplex receive only | |
(++) HAL_USART_TransmitReceive_DMA() in full duplex mode | |
(++) HAL_USART_DMAPause() | |
(++) HAL_USART_DMAResume() | |
(++) HAL_USART_DMAStop() | |
(#) A set of Transfer Complete Callbacks are provided in Non-Blocking mode: | |
(++) HAL_USART_TxCpltCallback() | |
(++) HAL_USART_RxCpltCallback() | |
(++) HAL_USART_TxHalfCpltCallback() | |
(++) HAL_USART_RxHalfCpltCallback() | |
(++) HAL_USART_ErrorCallback() | |
(++) HAL_USART_TxRxCpltCallback() | |
(#) Non-Blocking mode transfers could be aborted using Abort API's : | |
(++) HAL_USART_Abort() | |
(++) HAL_USART_Abort_IT() | |
(#) For Abort services based on interrupts (HAL_USART_Abort_IT), a Abort Complete Callbacks is provided: | |
(++) HAL_USART_AbortCpltCallback() | |
(#) In Non-Blocking mode transfers, possible errors are split into 2 categories. | |
Errors are handled as follows : | |
(++) Error is considered as Recoverable and non blocking : Transfer could go till end, but error severity is | |
to be evaluated by user : this concerns Frame Error, Parity Error or Noise Error in Interrupt mode reception . | |
Received character is then retrieved and stored in Rx buffer, Error code is set to allow user to identify error type, | |
and HAL_USART_ErrorCallback() user callback is executed. Transfer is kept ongoing on USART side. | |
If user wants to abort it, Abort services should be called by user. | |
(++) Error is considered as Blocking : Transfer could not be completed properly and is aborted. | |
This concerns Overrun Error In Interrupt mode reception and all errors in DMA mode. | |
Error code is set to allow user to identify error type, and HAL_USART_ErrorCallback() user callback is executed. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Simplex send an amount of data in blocking mode. | |
* @param husart USART handle. | |
* @param pTxData Pointer to data buffer. | |
* @param Size Amount of data to be sent. | |
* @param Timeout Timeout duration. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffer containing data to be sent, should be aligned on a half word frontier (16 bits) | |
* (as sent data will be handled using u16 pointer cast). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pTxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Transmit(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint16_t* tmp=0U; | |
uint32_t tickstart = 0U; | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pTxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pTxData buffer provided as input paramter | |
should be aligned on a u16 frontier, as data to be filled into TDR will be | |
handled through a u16 cast. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if((((uint32_t)pTxData)&1U) != 0U) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_TX; | |
/* Init tickstart for timeout managment*/ | |
tickstart = HAL_GetTick(); | |
husart->TxXferSize = Size; | |
husart->TxXferCount = Size; | |
/* Check the remaining data to be sent */ | |
while(husart->TxXferCount > 0) | |
{ | |
husart->TxXferCount--; | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) pTxData; | |
husart->Instance->TDR = (*tmp & (uint16_t)0x01FFU); | |
pTxData += 2U; | |
} | |
else | |
{ | |
husart->Instance->TDR = (*pTxData++ & (uint8_t)0xFFU); | |
} | |
} | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
/* At end of Tx process, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive an amount of data in blocking mode. | |
* @note To receive synchronous data, dummy data are simultaneously transmitted. | |
* @param husart USART handle. | |
* @param pRxData Pointer to data buffer. | |
* @param Size Amount of data to be received. | |
* @param Timeout Timeout duration. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffer for storing data to be received, should be aligned on a half word frontier (16 bits) | |
* (as received data will be handled using u16 pointer cast). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pRxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Receive(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint16_t* tmp=0U; | |
uint16_t uhMask; | |
uint32_t tickstart = 0U; | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pRxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pRxData buffer provided as input paramter | |
should be aligned on a u16 frontier, as data to be received from RDR will be | |
handled through a u16 cast. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if((((uint32_t)pRxData)&1U) != 0U) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_RX; | |
/* Init tickstart for timeout managment*/ | |
tickstart = HAL_GetTick(); | |
husart->RxXferSize = Size; | |
husart->RxXferCount = Size; | |
/* Computation of USART mask to apply to RDR register */ | |
USART_MASK_COMPUTATION(husart); | |
uhMask = husart->Mask; | |
/* as long as data have to be received */ | |
while(husart->RxXferCount > 0U) | |
{ | |
husart->RxXferCount--; | |
/* Wait until TC flag is set to send dummy byte in order to generate the | |
* clock for the slave to send data. | |
* Whatever the frame length (7, 8 or 9-bit long), the same dummy value | |
* can be written for all the cases. */ | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x0FFU); | |
/* Wait for RXNE Flag */ | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) pRxData ; | |
*tmp = (uint16_t)(husart->Instance->RDR & uhMask); | |
pRxData +=2; | |
} | |
else | |
{ | |
*pRxData++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); | |
} | |
} | |
/* At end of Rx process, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Full-Duplex Send and Receive an amount of data in blocking mode. | |
* @param husart USART handle. | |
* @param pTxData pointer to TX data buffer. | |
* @param pRxData pointer to RX data buffer. | |
* @param Size amount of data to be sent (same amount to be received). | |
* @param Timeout Timeout duration. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffers containing data to be sent/received, should be aligned on a half word frontier (16 bits) | |
* (as sent/received data will be handled using u16 pointer cast). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pTxData and pRxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_TransmitReceive(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size, uint32_t Timeout) | |
{ | |
uint16_t* tmp=0U; | |
uint16_t uhMask; | |
uint32_t tickstart = 0U; | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pTxData == NULL) || (pRxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pTxData and pRxData buffers provided as input paramter | |
should be aligned on a u16 frontier, as data to be filled into TDR/retrieved from RDR will be | |
handled through a u16 cast. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if(((((uint32_t)pTxData)&1U) != 0U) || ((((uint32_t)pRxData)&1U) != 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_RX; | |
/* Init tickstart for timeout managment*/ | |
tickstart = HAL_GetTick(); | |
husart->RxXferSize = Size; | |
husart->TxXferSize = Size; | |
husart->TxXferCount = Size; | |
husart->RxXferCount = Size; | |
/* Computation of USART mask to apply to RDR register */ | |
USART_MASK_COMPUTATION(husart); | |
uhMask = husart->Mask; | |
/* Check the remain data to be sent */ | |
while(husart->TxXferCount > 0U) | |
{ | |
husart->TxXferCount--; | |
husart->RxXferCount--; | |
/* Wait until TC flag is set to send data */ | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) pTxData; | |
husart->Instance->TDR = (*tmp & uhMask); | |
pTxData += 2U; | |
} | |
else | |
{ | |
husart->Instance->TDR = (*pTxData++ & (uint8_t)uhMask); | |
} | |
/* Wait for RXNE Flag */ | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK) | |
{ | |
return HAL_TIMEOUT; | |
} | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) pRxData ; | |
*tmp = (uint16_t)(husart->Instance->RDR & uhMask); | |
pRxData +=2U; | |
} | |
else | |
{ | |
*pRxData++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); | |
} | |
} | |
/* At end of TxRx process, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Send an amount of data in interrupt mode. | |
* @param husart USART handle. | |
* @param pTxData pointer to data buffer. | |
* @param Size amount of data to be sent. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffer containing data to be sent, should be aligned on a half word frontier (16 bits) | |
* (as sent data will be handled using u16 pointer cast). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pTxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Transmit_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size) | |
{ | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pTxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pTxData buffer provided as input paramter | |
should be aligned on a u16 frontier, as data to be filled into TDR will be | |
handled through a u16 cast. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if((((uint32_t)pTxData)&1U) != 0U) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->pTxBuffPtr = pTxData; | |
husart->TxXferSize = Size; | |
husart->TxXferCount = Size; | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_TX; | |
/* The USART Error Interrupts: (Frame error, noise error, overrun error) | |
are not managed by the USART Transmit Process to avoid the overrun interrupt | |
when the usart mode is configured for transmit and receive "USART_MODE_TX_RX" | |
to benefit for the frame error and noise interrupts the usart mode should be | |
configured only for transmit "USART_MODE_TX" */ | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
/* Enable the USART Transmit Data Register Empty Interrupt */ | |
__HAL_USART_ENABLE_IT(husart, USART_IT_TXE); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive an amount of data in interrupt mode. | |
* @note To receive synchronous data, dummy data are simultaneously transmitted. | |
* @param husart USART handle. | |
* @param pRxData pointer to data buffer. | |
* @param Size amount of data to be received. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffer for storing data to be received, should be aligned on a half word frontier (16 bits) | |
* (as received data will be handled using u16 pointer cast). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pRxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Receive_IT(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size) | |
{ | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pRxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pRxData buffer provided as input paramter | |
should be aligned on a u16 frontier, as data to be received from RDR will be | |
handled through a u16 cast. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if((((uint32_t)pRxData)&1U) != 0U) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->pRxBuffPtr = pRxData; | |
husart->RxXferSize = Size; | |
husart->RxXferCount = Size; | |
USART_MASK_COMPUTATION(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_RX; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
/* Enable the USART Parity Error and Data Register not empty Interrupts */ | |
SET_BIT(husart->Instance->CR1, USART_CR1_PEIE | USART_CR1_RXNEIE); | |
/* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Send dummy byte in order to generate the clock for the Slave to send the next data */ | |
if(husart->Init.WordLength == USART_WORDLENGTH_9B) | |
{ | |
husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x01FFU); | |
} | |
else | |
{ | |
husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x00FFU); | |
} | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Full-Duplex Send and Receive an amount of data in interrupt mode. | |
* @param husart USART handle. | |
* @param pTxData pointer to TX data buffer. | |
* @param pRxData pointer to RX data buffer. | |
* @param Size amount of data to be sent (same amount to be received). | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffers containing data to be sent/received, should be aligned on a half word frontier (16 bits) | |
* (as sent/received data will be handled using u16 pointer cast). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pTxData and pRxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_TransmitReceive_IT(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size) | |
{ | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pTxData == NULL) || (pRxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pTxData and pRxData buffers provided as input paramter | |
should be aligned on a u16 frontier, as data to be filled into TDR/retrieved from RDR will be | |
handled through a u16 cast. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if(((((uint32_t)pTxData)&1U) != 0U) || ((((uint32_t)pRxData)&1U) != 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->pRxBuffPtr = pRxData; | |
husart->RxXferSize = Size; | |
husart->RxXferCount = Size; | |
husart->pTxBuffPtr = pTxData; | |
husart->TxXferSize = Size; | |
husart->TxXferCount = Size; | |
/* Computation of USART mask to apply to RDR register */ | |
USART_MASK_COMPUTATION(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_TX_RX; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
/* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Enable the USART Parity Error and USART Data Register not empty Interrupts */ | |
SET_BIT(husart->Instance->CR1, USART_CR1_PEIE | USART_CR1_RXNEIE); | |
/* Enable the USART Transmit Data Register Empty Interrupt */ | |
SET_BIT(husart->Instance->CR1, USART_CR1_TXEIE); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Send an amount of data in DMA mode. | |
* @param husart USART handle. | |
* @param pTxData pointer to data buffer. | |
* @param Size amount of data to be sent. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffer containing data to be sent, should be aligned on a half word frontier (16 bits) | |
* (as sent data will be handled by DMA from halfword frontier). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pTxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Transmit_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint16_t Size) | |
{ | |
uint32_t *tmp=0U; | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pTxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pTxData buffer provided as input paramter | |
should be aligned on a u16 frontier, as data copy into TDR will be | |
handled by DMA from a u16 frontier. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if((((uint32_t)pTxData)&1U) != 0U) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->pTxBuffPtr = pTxData; | |
husart->TxXferSize = Size; | |
husart->TxXferCount = Size; | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_TX; | |
/* Set the USART DMA transfer complete callback */ | |
husart->hdmatx->XferCpltCallback = USART_DMATransmitCplt; | |
/* Set the USART DMA Half transfer complete callback */ | |
husart->hdmatx->XferHalfCpltCallback = USART_DMATxHalfCplt; | |
/* Set the DMA error callback */ | |
husart->hdmatx->XferErrorCallback = USART_DMAError; | |
/* Enable the USART transmit DMA channel */ | |
tmp = (uint32_t*)&pTxData; | |
HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t*)tmp, (uint32_t)&husart->Instance->TDR, Size); | |
/* Clear the TC flag in the ICR register */ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_TCF); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
/* Enable the DMA transfer for transmit request by setting the DMAT bit | |
in the USART CR3 register */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Receive an amount of data in DMA mode. | |
* @param husart USART handle. | |
* @param pRxData pointer to data buffer. | |
* @param Size amount of data to be received. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffer for storing data to be received, should be aligned on a half word frontier (16 bits) | |
* (as received data will be handled by DMA from halfword frontier). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pRxData. | |
* @note The USART DMA transmit channel must be configured in order to generate the clock for the slave. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Receive_DMA(USART_HandleTypeDef *husart, uint8_t *pRxData, uint16_t Size) | |
{ | |
uint32_t *tmp; | |
/* Check that a Rx process is not already ongoing */ | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pRxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pRxData buffer provided as input paramter | |
should be aligned on a u16 frontier, as data copy from RDR will be | |
handled by DMA from a u16 frontier. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if((((uint32_t)pRxData)&1U) != 0U) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->pRxBuffPtr = pRxData; | |
husart->RxXferSize = Size; | |
husart->pTxBuffPtr = pRxData; | |
husart->TxXferSize = Size; | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_RX; | |
/* Set the USART DMA Rx transfer complete callback */ | |
husart->hdmarx->XferCpltCallback = USART_DMAReceiveCplt; | |
/* Set the USART DMA Half transfer complete callback */ | |
husart->hdmarx->XferHalfCpltCallback = USART_DMARxHalfCplt; | |
/* Set the USART DMA Rx transfer error callback */ | |
husart->hdmarx->XferErrorCallback = USART_DMAError; | |
/* Enable the USART receive DMA channel */ | |
tmp = (uint32_t*)&pRxData; | |
HAL_DMA_Start_IT(husart->hdmarx, (uint32_t)&husart->Instance->RDR, *(uint32_t*)tmp, Size); | |
/* Enable the USART transmit DMA channel: the transmit channel is used in order | |
to generate in the non-blocking mode the clock to the slave device, | |
this mode isn't a simplex receive mode but a full-duplex receive mode */ | |
/* Set the USART DMA Tx Complete and Error callback to Null */ | |
husart->hdmatx->XferErrorCallback = NULL; | |
husart->hdmatx->XferHalfCpltCallback = NULL; | |
husart->hdmatx->XferCpltCallback = NULL; | |
HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t*)tmp, (uint32_t)&husart->Instance->TDR, Size); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
/* Enable the USART Parity Error Interrupt */ | |
SET_BIT(husart->Instance->CR1, USART_CR1_PEIE); | |
/* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Enable the DMA transfer for the receiver request by setting the DMAR bit | |
in the USART CR3 register */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* Enable the DMA transfer for transmit request by setting the DMAT bit | |
in the USART CR3 register */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Full-Duplex Transmit Receive an amount of data in non-blocking mode. | |
* @param husart USART handle. | |
* @param pTxData pointer to TX data buffer. | |
* @param pRxData pointer to RX data buffer. | |
* @param Size amount of data to be received/sent. | |
* @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), | |
* address of user data buffers containing data to be sent/received, should be aligned on a half word frontier (16 bits) | |
* (as sent/received data will be handled by DMA from halfword frontier). Depending on compilation chain, | |
* use of specific alignment compilation directives or pragmas might be required to ensure proper alignment for pTxData and pRxData. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_TransmitReceive_DMA(USART_HandleTypeDef *husart, uint8_t *pTxData, uint8_t *pRxData, uint16_t Size) | |
{ | |
uint32_t *tmp; | |
if(husart->State == HAL_USART_STATE_READY) | |
{ | |
if((pTxData == NULL) || (pRxData == NULL) || (Size == 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
/* In case of 9bits/No Parity transfer, pTxData and pRxData buffers provided as input paramter | |
should be aligned on a u16 frontier, as data copy to/from TDR/RDR will be | |
handled by DMA from a u16 frontier. */ | |
if ((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
if(((((uint32_t)pTxData)&1U) != 0U) || ((((uint32_t)pRxData)&1U) != 0U)) | |
{ | |
return HAL_ERROR; | |
} | |
} | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
husart->pRxBuffPtr = pRxData; | |
husart->RxXferSize = Size; | |
husart->pTxBuffPtr = pTxData; | |
husart->TxXferSize = Size; | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
husart->State = HAL_USART_STATE_BUSY_TX_RX; | |
/* Set the USART DMA Rx transfer complete callback */ | |
husart->hdmarx->XferCpltCallback = USART_DMAReceiveCplt; | |
/* Set the USART DMA Half transfer complete callback */ | |
husart->hdmarx->XferHalfCpltCallback = USART_DMARxHalfCplt; | |
/* Set the USART DMA Tx transfer complete callback */ | |
husart->hdmatx->XferCpltCallback = USART_DMATransmitCplt; | |
/* Set the USART DMA Half transfer complete callback */ | |
husart->hdmatx->XferHalfCpltCallback = USART_DMATxHalfCplt; | |
/* Set the USART DMA Tx transfer error callback */ | |
husart->hdmatx->XferErrorCallback = USART_DMAError; | |
/* Set the USART DMA Rx transfer error callback */ | |
husart->hdmarx->XferErrorCallback = USART_DMAError; | |
/* Enable the USART receive DMA channel */ | |
tmp = (uint32_t*)&pRxData; | |
HAL_DMA_Start_IT(husart->hdmarx, (uint32_t)&husart->Instance->RDR, *(uint32_t*)tmp, Size); | |
/* Enable the USART transmit DMA channel */ | |
tmp = (uint32_t*)&pTxData; | |
HAL_DMA_Start_IT(husart->hdmatx, *(uint32_t*)tmp, (uint32_t)&husart->Instance->TDR, Size); | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
/* Enable the USART Parity Error Interrupt */ | |
SET_BIT(husart->Instance->CR1, USART_CR1_PEIE); | |
/* Enable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Clear the TC flag in the ICR register */ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_TCF); | |
/* Enable the DMA transfer for the receiver request by setting the DMAR bit | |
in the USART CR3 register */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* Enable the DMA transfer for transmit request by setting the DMAT bit | |
in the USART CR3 register */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Pause the DMA Transfer. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_DMAPause(USART_HandleTypeDef *husart) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
if( (husart->State == HAL_USART_STATE_BUSY_TX) && | |
(HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT))) | |
{ | |
/* Disable the USART DMA Tx request */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
} | |
else if( (husart->State == HAL_USART_STATE_BUSY_RX) || | |
(husart->State == HAL_USART_STATE_BUSY_TX_RX) ) | |
{ | |
if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT)) | |
{ | |
/* Disable the USART DMA Tx request */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
} | |
if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR)) | |
{ | |
/* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */ | |
CLEAR_BIT(husart->Instance->CR1, USART_CR1_PEIE); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Disable the USART DMA Rx request */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
} | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
/** | |
* @brief Resume the DMA Transfer. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_DMAResume(USART_HandleTypeDef *husart) | |
{ | |
/* Process Locked */ | |
__HAL_LOCK(husart); | |
if(husart->State == HAL_USART_STATE_BUSY_TX) | |
{ | |
/* Enable the USART DMA Tx request */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
} | |
else if( (husart->State == HAL_USART_STATE_BUSY_RX) || | |
(husart->State == HAL_USART_STATE_BUSY_TX_RX) ) | |
{ | |
/* Clear the Overrun flag before resuming the Rx transfer*/ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF); | |
/* Reenable PE and ERR (Frame error, noise error, overrun error) interrupts */ | |
SET_BIT(husart->Instance->CR1, USART_CR1_PEIE); | |
SET_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Enable the USART DMA Rx request before the DMA Tx request */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* Enable the USART DMA Tx request */ | |
SET_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
} | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
/** | |
* @brief Stop the DMA Transfer. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_DMAStop(USART_HandleTypeDef *husart) | |
{ | |
/* The Lock is not implemented on this API to allow the user application | |
to call the HAL USART API under callbacks HAL_USART_TxCpltCallback() / HAL_USART_RxCpltCallback() / | |
HAL_USART_TxHalfCpltCallback() / HAL_USART_RxHalfCpltCallback (): | |
indeed, when HAL_DMA_Abort() API is called, the DMA TX/RX Transfer or Half Transfer complete interrupt is | |
generated if the DMA transfer interruption occurs at the middle or at the end of the stream | |
and the corresponding call back is executed. | |
*/ | |
/* Disable the USART Tx/Rx DMA requests */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* Abort the USART DMA tx channel */ | |
if(husart->hdmatx != NULL) | |
{ | |
HAL_DMA_Abort(husart->hdmatx); | |
} | |
/* Abort the USART DMA rx channel */ | |
if(husart->hdmarx != NULL) | |
{ | |
HAL_DMA_Abort(husart->hdmarx); | |
} | |
USART_EndTransfer(husart); | |
husart->State = HAL_USART_STATE_READY; | |
return HAL_OK; | |
} | |
/** | |
* @brief Abort ongoing transfers (blocking mode). | |
* @param husart USART handle. | |
* @note This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. | |
* This procedure performs following operations : | |
* - Disable USART Interrupts (Tx and Rx) | |
* - Disable the DMA transfer in the peripheral register (if enabled) | |
* - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode) | |
* - Set handle State to READY | |
* @note This procedure is executed in blocking mode : when exiting function, Abort is considered as completed. | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Abort(USART_HandleTypeDef *husart) | |
{ | |
/* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ | |
CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE)); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Disable the USART DMA Tx request if enabled */ | |
if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT)) | |
{ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
/* Abort the USART DMA Tx channel : use blocking DMA Abort API (no callback) */ | |
if(husart->hdmatx != NULL) | |
{ | |
/* Set the USART DMA Abort callback to Null. | |
No call back execution at end of DMA abort procedure */ | |
husart->hdmatx->XferAbortCallback = NULL; | |
HAL_DMA_Abort(husart->hdmatx); | |
} | |
} | |
/* Disable the USART DMA Rx request if enabled */ | |
if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR)) | |
{ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* Abort the USART DMA Rx channel : use blocking DMA Abort API (no callback) */ | |
if(husart->hdmarx != NULL) | |
{ | |
/* Set the USART DMA Abort callback to Null. | |
No call back execution at end of DMA abort procedure */ | |
husart->hdmarx->XferAbortCallback = NULL; | |
HAL_DMA_Abort(husart->hdmarx); | |
} | |
} | |
/* Reset Tx and Rx transfer counters */ | |
husart->TxXferCount = 0U; | |
husart->RxXferCount = 0U; | |
/* Clear the Error flags in the ICR register */ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF | USART_CLEAR_NEF | USART_CLEAR_PEF | USART_CLEAR_FEF); | |
/* Restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* Reset Handle ErrorCode to No Error */ | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
return HAL_OK; | |
} | |
/** | |
* @brief Abort ongoing transfers (Interrupt mode). | |
* @param husart USART handle. | |
* @note This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. | |
* This procedure performs following operations : | |
* - Disable USART Interrupts (Tx and Rx) | |
* - Disable the DMA transfer in the peripheral register (if enabled) | |
* - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode) | |
* - Set handle State to READY | |
* - At abort completion, call user abort complete callback | |
* @note This procedure is executed in Interrupt mode, meaning that abort procedure could be | |
* considered as completed only when user abort complete callback is executed (not when exiting function). | |
* @retval HAL status | |
*/ | |
HAL_StatusTypeDef HAL_USART_Abort_IT(USART_HandleTypeDef *husart) | |
{ | |
uint32_t abortcplt = 1U; | |
/* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ | |
CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE)); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* If DMA Tx and/or DMA Rx Handles are associated to USART Handle, DMA Abort complete callbacks should be initialised | |
before any call to DMA Abort functions */ | |
/* DMA Tx Handle is valid */ | |
if(husart->hdmatx != NULL) | |
{ | |
/* Set DMA Abort Complete callback if USART DMA Tx request if enabled. | |
Otherwise, set it to NULL */ | |
if(HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT)) | |
{ | |
husart->hdmatx->XferAbortCallback = USART_DMATxAbortCallback; | |
} | |
else | |
{ | |
husart->hdmatx->XferAbortCallback = NULL; | |
} | |
} | |
/* DMA Rx Handle is valid */ | |
if(husart->hdmarx != NULL) | |
{ | |
/* Set DMA Abort Complete callback if USART DMA Rx request if enabled. | |
Otherwise, set it to NULL */ | |
if(HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR)) | |
{ | |
husart->hdmarx->XferAbortCallback = USART_DMARxAbortCallback; | |
} | |
else | |
{ | |
husart->hdmarx->XferAbortCallback = NULL; | |
} | |
} | |
/* Disable the USART DMA Tx request if enabled */ | |
if(HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAT)) | |
{ | |
/* Disable DMA Tx at USART level */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
/* Abort the USART DMA Tx channel : use non blocking DMA Abort API (callback) */ | |
if(husart->hdmatx != NULL) | |
{ | |
/* USART Tx DMA Abort callback has already been initialised : | |
will lead to call HAL_USART_AbortCpltCallback() at end of DMA abort procedure */ | |
/* Abort DMA TX */ | |
if(HAL_DMA_Abort_IT(husart->hdmatx) != HAL_OK) | |
{ | |
husart->hdmatx->XferAbortCallback = NULL; | |
} | |
else | |
{ | |
abortcplt = 0U; | |
} | |
} | |
} | |
/* Disable the USART DMA Rx request if enabled */ | |
if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR)) | |
{ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* Abort the USART DMA Rx channel : use non blocking DMA Abort API (callback) */ | |
if(husart->hdmarx != NULL) | |
{ | |
/* USART Rx DMA Abort callback has already been initialised : | |
will lead to call HAL_USART_AbortCpltCallback() at end of DMA abort procedure */ | |
/* Abort DMA RX */ | |
if(HAL_DMA_Abort_IT(husart->hdmarx) != HAL_OK) | |
{ | |
husart->hdmarx->XferAbortCallback = NULL; | |
abortcplt = 1U; | |
} | |
else | |
{ | |
abortcplt = 0U; | |
} | |
} | |
} | |
/* if no DMA abort complete callback execution is required => call user Abort Complete callback */ | |
if (abortcplt == 1U) | |
{ | |
/* Reset Tx and Rx transfer counters */ | |
husart->TxXferCount = 0U; | |
husart->RxXferCount = 0U; | |
/* Reset errorCode */ | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
/* Clear the Error flags in the ICR register */ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF | USART_CLEAR_NEF | USART_CLEAR_PEF | USART_CLEAR_FEF); | |
/* Restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* As no DMA to be aborted, call directly user Abort complete callback */ | |
HAL_USART_AbortCpltCallback(husart); | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Handle USART interrupt request. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
void HAL_USART_IRQHandler(USART_HandleTypeDef *husart) | |
{ | |
uint32_t isrflags = READ_REG(husart->Instance->ISR); | |
uint32_t cr1its = READ_REG(husart->Instance->CR1); | |
uint32_t cr3its; | |
uint32_t errorflags; | |
/* If no error occurs */ | |
errorflags = (isrflags & (uint32_t)(USART_ISR_PE | USART_ISR_FE | USART_ISR_ORE | USART_ISR_NE)); | |
if (errorflags == RESET) | |
{ | |
/* USART in mode Receiver ---------------------------------------------------*/ | |
if(((isrflags & USART_ISR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET)) | |
{ | |
if(husart->State == HAL_USART_STATE_BUSY_RX) | |
{ | |
USART_Receive_IT(husart); | |
} | |
else | |
{ | |
USART_TransmitReceive_IT(husart); | |
} | |
return; | |
} | |
} | |
/* If some errors occur */ | |
cr3its = READ_REG(husart->Instance->CR3); | |
if( (errorflags != RESET) | |
&& ( ((cr3its & USART_CR3_EIE) != RESET) | |
|| ((cr1its & (USART_CR1_RXNEIE | USART_CR1_PEIE)) != RESET)) ) | |
{ | |
/* USART parity error interrupt occurred -------------------------------------*/ | |
if(((isrflags & USART_ISR_PE) != RESET) && ((cr1its & USART_CR1_PEIE) != RESET)) | |
{ | |
__HAL_USART_CLEAR_IT(husart, USART_CLEAR_PEF); | |
husart->ErrorCode |= HAL_USART_ERROR_PE; | |
} | |
/* USART frame error interrupt occurred --------------------------------------*/ | |
if(((isrflags & USART_ISR_FE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) | |
{ | |
__HAL_USART_CLEAR_IT(husart, USART_CLEAR_FEF); | |
husart->ErrorCode |= HAL_USART_ERROR_FE; | |
} | |
/* USART noise error interrupt occurred --------------------------------------*/ | |
if(((isrflags & USART_ISR_NE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) | |
{ | |
__HAL_USART_CLEAR_IT(husart, USART_CLEAR_NEF); | |
husart->ErrorCode |= HAL_USART_ERROR_NE; | |
} | |
/* USART Over-Run interrupt occurred -----------------------------------------*/ | |
if(((isrflags & USART_ISR_ORE) != RESET) && | |
(((cr1its & USART_CR1_RXNEIE) != RESET) || ((cr3its & USART_CR3_EIE) != RESET))) | |
{ | |
__HAL_USART_CLEAR_IT(husart, USART_CLEAR_OREF); | |
husart->ErrorCode |= HAL_USART_ERROR_ORE; | |
} | |
/* Call USART Error Call back function if need be --------------------------*/ | |
if(husart->ErrorCode != HAL_USART_ERROR_NONE) | |
{ | |
/* USART in mode Receiver ---------------------------------------------------*/ | |
if(((isrflags & USART_ISR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET)) | |
{ | |
if(husart->State == HAL_USART_STATE_BUSY_RX) | |
{ | |
USART_Receive_IT(husart); | |
} | |
else | |
{ | |
USART_TransmitReceive_IT(husart); | |
} | |
} | |
/* If Overrun error occurs, or if any error occurs in DMA mode reception, | |
consider error as blocking */ | |
if (((husart->ErrorCode & HAL_USART_ERROR_ORE) != RESET) || | |
(HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR))) | |
{ | |
/* Blocking error : transfer is aborted | |
Set the USART state ready to be able to start again the process, | |
Disable Interrupts, and disable DMA requests, if ongoing */ | |
USART_EndTransfer(husart); | |
/* Disable the USART DMA Rx request if enabled */ | |
if (HAL_IS_BIT_SET(husart->Instance->CR3, USART_CR3_DMAR)) | |
{ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR | USART_CR3_DMAR); | |
/* Abort the USART DMA Tx channel */ | |
if(husart->hdmatx != NULL) | |
{ | |
/* Set the USART Tx DMA Abort callback to NULL : no callback | |
executed at end of DMA abort procedure */ | |
husart->hdmatx->XferAbortCallback = NULL; | |
/* Abort DMA TX */ | |
HAL_DMA_Abort_IT(husart->hdmatx); | |
} | |
/* Abort the USART DMA Rx channel */ | |
if(husart->hdmarx != NULL) | |
{ | |
/* Set the USART Rx DMA Abort callback : | |
will lead to call HAL_USART_ErrorCallback() at end of DMA abort procedure */ | |
husart->hdmarx->XferAbortCallback = USART_DMAAbortOnError; | |
/* Abort DMA RX */ | |
if(HAL_DMA_Abort_IT(husart->hdmarx) != HAL_OK) | |
{ | |
/* Call Directly husart->hdmarx->XferAbortCallback function in case of error */ | |
husart->hdmarx->XferAbortCallback(husart->hdmarx); | |
} | |
} | |
else | |
{ | |
/* Call user error callback */ | |
HAL_USART_ErrorCallback(husart); | |
} | |
} | |
else | |
{ | |
/* Call user error callback */ | |
HAL_USART_ErrorCallback(husart); | |
} | |
} | |
else | |
{ | |
/* Non Blocking error : transfer could go on. | |
Error is notified to user through user error callback */ | |
HAL_USART_ErrorCallback(husart); | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
} | |
} | |
return; | |
} /* End if some error occurs */ | |
/* USART in mode Transmitter ------------------------------------------------*/ | |
if(((isrflags & USART_ISR_TXE) != RESET) && ((cr1its & USART_CR1_TXEIE) != RESET)) | |
{ | |
if(husart->State == HAL_USART_STATE_BUSY_TX) | |
{ | |
USART_Transmit_IT(husart); | |
} | |
else | |
{ | |
USART_TransmitReceive_IT(husart); | |
} | |
return; | |
} | |
/* USART in mode Transmitter (transmission end) -----------------------------*/ | |
if(((isrflags & USART_ISR_TC) != RESET) && ((cr1its & USART_CR1_TCIE) != RESET)) | |
{ | |
USART_EndTransmit_IT(husart); | |
return; | |
} | |
} | |
/** | |
* @brief Tx Transfer completed callback. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_TxCpltCallback(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_TxCpltCallback can be implemented in the user file. | |
*/ | |
} | |
/** | |
* @brief Tx Half Transfer completed callback. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_TxHalfCpltCallback(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE: This function should not be modified, when the callback is needed, | |
the HAL_USART_TxHalfCpltCallback can be implemented in the user file. | |
*/ | |
} | |
/** | |
* @brief Rx Transfer completed callback. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_RxCpltCallback(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE: This function should not be modified, when the callback is needed, | |
the HAL_USART_RxCpltCallback can be implemented in the user file. | |
*/ | |
} | |
/** | |
* @brief Rx Half Transfer completed callback. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_RxHalfCpltCallback(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_RxHalfCpltCallback can be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Tx/Rx Transfers completed callback for the non-blocking process. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_TxRxCpltCallback(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_TxRxCpltCallback can be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief USART error callback. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_ErrorCallback(USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_ErrorCallback can be implemented in the user file. | |
*/ | |
} | |
/** | |
* @brief USART Abort Complete callback. | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
__weak void HAL_USART_AbortCpltCallback (USART_HandleTypeDef *husart) | |
{ | |
/* Prevent unused argument(s) compilation warning */ | |
UNUSED(husart); | |
/* NOTE : This function should not be modified, when the callback is needed, | |
the HAL_USART_AbortCpltCallback can be implemented in the user file. | |
*/ | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup USART_Exported_Functions_Group3 Peripheral State and Error functions | |
* @brief USART Peripheral State and Error functions | |
* | |
@verbatim | |
============================================================================== | |
##### Peripheral State and Error functions ##### | |
============================================================================== | |
[..] | |
This subsection provides functions allowing to : | |
(+) Return the USART handle state | |
(+) Return the USART handle error code | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Return the USART handle state. | |
* @param husart pointer to a USART_HandleTypeDef structure that contains | |
* the configuration information for the specified USART. | |
* @retval USART handle state | |
*/ | |
HAL_USART_StateTypeDef HAL_USART_GetState(USART_HandleTypeDef *husart) | |
{ | |
return husart->State; | |
} | |
/** | |
* @brief Return the USART error code. | |
* @param husart pointer to a USART_HandleTypeDef structure that contains | |
* the configuration information for the specified USART. | |
* @retval USART handle Error Code | |
*/ | |
uint32_t HAL_USART_GetError(USART_HandleTypeDef *husart) | |
{ | |
return husart->ErrorCode; | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/** @defgroup USART_Private_Functions USART Private Functions | |
* @brief USART Private functions | |
* | |
@verbatim | |
[..] | |
This subsection provides a set of functions allowing to control the USART. | |
(+) USART_SetConfig() API is used to set the USART communication parameters. | |
(+) USART_CheckIdleState() APi ensures that TEACK and/or REACK bits are set after initialization | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief End ongoing transfer on USART peripheral (following error detection or Transfer completion). | |
* @param husart USART handle. | |
* @retval None | |
*/ | |
static void USART_EndTransfer(USART_HandleTypeDef *husart) | |
{ | |
/* Disable TXEIE and TCIE interrupts */ | |
/* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ | |
CLEAR_BIT(husart->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE | USART_CR1_RXNEIE | USART_CR1_PEIE)); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* At end of process, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
} | |
/** | |
* @brief DMA USART transmit process complete callback. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMATransmitCplt(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef*)(hdma->Parent); | |
/* DMA Normal mode */ | |
if ( HAL_IS_BIT_CLR(hdma->Instance->CCR, DMA_CCR_CIRC) ) | |
{ | |
husart->TxXferCount = 0U; | |
if(husart->State == HAL_USART_STATE_BUSY_TX) | |
{ | |
/* Disable the DMA transfer for transmit request by resetting the DMAT bit | |
in the USART CR3 register */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
/* Enable the USART Transmit Complete Interrupt */ | |
__HAL_USART_ENABLE_IT(husart, USART_IT_TC); | |
} | |
} | |
/* DMA Circular mode */ | |
else | |
{ | |
if(husart->State == HAL_USART_STATE_BUSY_TX) | |
{ | |
HAL_USART_TxCpltCallback(husart); | |
} | |
} | |
} | |
/** | |
* @brief DMA USART transmit process half complete callback. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMATxHalfCplt(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef*)(hdma->Parent); | |
HAL_USART_TxHalfCpltCallback(husart); | |
} | |
/** | |
* @brief DMA USART receive process complete callback. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMAReceiveCplt(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef*)(hdma->Parent); | |
/* DMA Normal mode */ | |
if ( HAL_IS_BIT_CLR(hdma->Instance->CCR, DMA_CCR_CIRC) ) | |
{ | |
husart->RxXferCount = 0U; | |
/* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */ | |
CLEAR_BIT(husart->Instance->CR1, USART_CR1_PEIE); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Disable the DMA RX transfer for the receiver request by resetting the DMAR bit | |
in USART CR3 register */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAR); | |
/* similarly, disable the DMA TX transfer that was started to provide the | |
clock to the slave device */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_DMAT); | |
if(husart->State == HAL_USART_STATE_BUSY_RX) | |
{ | |
HAL_USART_RxCpltCallback(husart); | |
} | |
/* The USART state is HAL_USART_STATE_BUSY_TX_RX */ | |
else | |
{ | |
HAL_USART_TxRxCpltCallback(husart); | |
} | |
husart->State= HAL_USART_STATE_READY; | |
} | |
/* DMA circular mode */ | |
else | |
{ | |
if(husart->State == HAL_USART_STATE_BUSY_RX) | |
{ | |
HAL_USART_RxCpltCallback(husart); | |
} | |
/* The USART state is HAL_USART_STATE_BUSY_TX_RX */ | |
else | |
{ | |
HAL_USART_TxRxCpltCallback(husart); | |
} | |
} | |
} | |
/** | |
* @brief DMA USART receive process half complete callback. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMARxHalfCplt(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef*)(hdma->Parent); | |
HAL_USART_RxHalfCpltCallback(husart); | |
} | |
/** | |
* @brief DMA USART communication error callback. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMAError(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef*)(hdma->Parent); | |
husart->RxXferCount = 0U; | |
husart->TxXferCount = 0U; | |
USART_EndTransfer(husart); | |
husart->ErrorCode |= HAL_USART_ERROR_DMA; | |
husart->State= HAL_USART_STATE_READY; | |
HAL_USART_ErrorCallback(husart); | |
} | |
/** | |
* @brief DMA USART communication abort callback, when initiated by HAL services on Error | |
* (To be called at end of DMA Abort procedure following error occurrence). | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMAAbortOnError(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef*)(hdma->Parent); | |
husart->RxXferCount = 0U; | |
husart->TxXferCount = 0U; | |
HAL_USART_ErrorCallback(husart); | |
} | |
/** | |
* @brief DMA USART Tx communication abort callback, when initiated by user | |
* (To be called at end of DMA Tx Abort procedure following user abort request). | |
* @note When this callback is executed, User Abort complete call back is called only if no | |
* Abort still ongoing for Rx DMA Handle. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMATxAbortCallback(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef* )(hdma->Parent); | |
husart->hdmatx->XferAbortCallback = NULL; | |
/* Check if an Abort process is still ongoing */ | |
if(husart->hdmarx != NULL) | |
{ | |
if(husart->hdmarx->XferAbortCallback != NULL) | |
{ | |
return; | |
} | |
} | |
/* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */ | |
husart->TxXferCount = 0U; | |
husart->RxXferCount = 0U; | |
/* Reset errorCode */ | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
/* Clear the Error flags in the ICR register */ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF | USART_CLEAR_NEF | USART_CLEAR_PEF | USART_CLEAR_FEF); | |
/* Restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* Call user Abort complete callback */ | |
HAL_USART_AbortCpltCallback(husart); | |
} | |
/** | |
* @brief DMA USART Rx communication abort callback, when initiated by user | |
* (To be called at end of DMA Rx Abort procedure following user abort request). | |
* @note When this callback is executed, User Abort complete call back is called only if no | |
* Abort still ongoing for Tx DMA Handle. | |
* @param hdma DMA handle. | |
* @retval None | |
*/ | |
static void USART_DMARxAbortCallback(DMA_HandleTypeDef *hdma) | |
{ | |
USART_HandleTypeDef* husart = (USART_HandleTypeDef* )(hdma->Parent); | |
husart->hdmarx->XferAbortCallback = NULL; | |
/* Check if an Abort process is still ongoing */ | |
if(husart->hdmatx != NULL) | |
{ | |
if(husart->hdmatx->XferAbortCallback != NULL) | |
{ | |
return; | |
} | |
} | |
/* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */ | |
husart->TxXferCount = 0U; | |
husart->RxXferCount = 0U; | |
/* Reset errorCode */ | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
/* Clear the Error flags in the ICR register */ | |
__HAL_USART_CLEAR_FLAG(husart, USART_CLEAR_OREF | USART_CLEAR_NEF | USART_CLEAR_PEF | USART_CLEAR_FEF); | |
/* Restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
/* Call user Abort complete callback */ | |
HAL_USART_AbortCpltCallback(husart); | |
} | |
/** | |
* @brief Handle USART Communication Timeout. | |
* @param husart USART handle. | |
* @param Flag Specifies the USART flag to check. | |
* @param Status the Flag status (SET or RESET). | |
* @param Tickstart Tick start value | |
* @param Timeout timeout duration. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_WaitOnFlagUntilTimeout(USART_HandleTypeDef *husart, uint32_t Flag, FlagStatus Status, uint32_t Tickstart, uint32_t Timeout) | |
{ | |
/* Wait until flag is set */ | |
while((__HAL_USART_GET_FLAG(husart, Flag) ? SET : RESET) == Status) | |
{ | |
/* Check for the Timeout */ | |
if(Timeout != HAL_MAX_DELAY) | |
{ | |
if((Timeout == 0U) || ((HAL_GetTick()-Tickstart) > Timeout)) | |
{ | |
/* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ | |
CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE)); | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
husart->State= HAL_USART_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
return HAL_OK; | |
} | |
/** | |
* @brief Configure the USART peripheral. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_SetConfig(USART_HandleTypeDef *husart) | |
{ | |
uint32_t tmpreg = 0x0U; | |
USART_ClockSourceTypeDef clocksource = USART_CLOCKSOURCE_UNDEFINED; | |
HAL_StatusTypeDef ret = HAL_OK; | |
uint16_t brrtemp = 0x0000U; | |
uint16_t usartdiv = 0x0000U; | |
/* Check the parameters */ | |
assert_param(IS_USART_POLARITY(husart->Init.CLKPolarity)); | |
assert_param(IS_USART_PHASE(husart->Init.CLKPhase)); | |
assert_param(IS_USART_LASTBIT(husart->Init.CLKLastBit)); | |
assert_param(IS_USART_BAUDRATE(husart->Init.BaudRate)); | |
assert_param(IS_USART_WORD_LENGTH(husart->Init.WordLength)); | |
assert_param(IS_USART_STOPBITS(husart->Init.StopBits)); | |
assert_param(IS_USART_PARITY(husart->Init.Parity)); | |
assert_param(IS_USART_MODE(husart->Init.Mode)); | |
/*-------------------------- USART CR1 Configuration -----------------------*/ | |
/* Clear M, PCE, PS, TE and RE bits and configure | |
* the USART Word Length, Parity and Mode: | |
* set the M bits according to husart->Init.WordLength value | |
* set PCE and PS bits according to husart->Init.Parity value | |
* set TE and RE bits according to husart->Init.Mode value | |
* force OVER8 to 1 to allow to reach the maximum speed (Fclock/8) */ | |
tmpreg = (uint32_t)husart->Init.WordLength | husart->Init.Parity | husart->Init.Mode | USART_CR1_OVER8; | |
MODIFY_REG(husart->Instance->CR1, USART_CR1_FIELDS, tmpreg); | |
/*---------------------------- USART CR2 Configuration ---------------------*/ | |
/* Clear and configure the USART Clock, CPOL, CPHA, LBCL and STOP bits: | |
* set CPOL bit according to husart->Init.CLKPolarity value | |
* set CPHA bit according to husart->Init.CLKPhase value | |
* set LBCL bit according to husart->Init.CLKLastBit value | |
* set STOP[13:12] bits according to husart->Init.StopBits value */ | |
tmpreg = (uint32_t)(USART_CLOCK_ENABLE); | |
tmpreg |= ((uint32_t)husart->Init.CLKPolarity | (uint32_t)husart->Init.CLKPhase); | |
tmpreg |= ((uint32_t)husart->Init.CLKLastBit | (uint32_t)husart->Init.StopBits); | |
MODIFY_REG(husart->Instance->CR2, USART_CR2_FIELDS, tmpreg); | |
/*-------------------------- USART CR3 Configuration -----------------------*/ | |
/* no CR3 register configuration */ | |
/*-------------------------- USART BRR Configuration -----------------------*/ | |
/* BRR is filled-up according to OVER8 bit setting which is forced to 1 */ | |
USART_GETCLOCKSOURCE(husart, clocksource); | |
switch (clocksource) | |
{ | |
case USART_CLOCKSOURCE_PCLK1: | |
usartdiv = (uint16_t)(((2*HAL_RCC_GetPCLK1Freq()) + (husart->Init.BaudRate/2)) / husart->Init.BaudRate); | |
break; | |
case USART_CLOCKSOURCE_HSI: | |
usartdiv = (uint16_t)(((2*HSI_VALUE) + (husart->Init.BaudRate/2)) / husart->Init.BaudRate); | |
break; | |
case USART_CLOCKSOURCE_SYSCLK: | |
usartdiv = (uint16_t)(((2*HAL_RCC_GetSysClockFreq()) + (husart->Init.BaudRate/2)) / husart->Init.BaudRate); | |
break; | |
case USART_CLOCKSOURCE_LSE: | |
usartdiv = (uint16_t)(((2*LSE_VALUE) + (husart->Init.BaudRate/2)) / husart->Init.BaudRate); | |
break; | |
case USART_CLOCKSOURCE_UNDEFINED: | |
default: | |
ret = HAL_ERROR; | |
break; | |
} | |
brrtemp = usartdiv & 0xFFF0U; | |
brrtemp |= (uint16_t)((usartdiv & (uint16_t)0x000FU) >> 1U); | |
husart->Instance->BRR = brrtemp; | |
return ret; | |
} | |
/** | |
* @brief Check the USART Idle State. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_CheckIdleState(USART_HandleTypeDef *husart) | |
{ | |
#if !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC) | |
uint32_t tickstart = 0U; | |
#endif /* !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC) */ | |
/* Initialize the USART ErrorCode */ | |
husart->ErrorCode = HAL_USART_ERROR_NONE; | |
#if !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC) | |
/* Init tickstart for timeout managment*/ | |
tickstart = HAL_GetTick(); | |
/* TEACK and REACK bits in ISR are checked only when available (not available on all F0 devices). | |
Bits are defined for some specific devices, and are available only for UART instances supporting WakeUp from Stop Mode feature. | |
*/ | |
if (IS_UART_WAKEUP_FROMSTOP_INSTANCE(husart->Instance)) | |
{ | |
/* Check if the Transmitter is enabled */ | |
if((husart->Instance->CR1 & USART_CR1_TE) == USART_CR1_TE) | |
{ | |
/* Wait until TEACK flag is set */ | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_ISR_TEACK, RESET, tickstart, USART_TEACK_REACK_TIMEOUT) != HAL_OK) | |
{ | |
/* Timeout occurred */ | |
return HAL_TIMEOUT; | |
} | |
} | |
/* Check if the Receiver is enabled */ | |
if((husart->Instance->CR1 & USART_CR1_RE) == USART_CR1_RE) | |
{ | |
/* Wait until REACK flag is set */ | |
if(USART_WaitOnFlagUntilTimeout(husart, USART_ISR_REACK, RESET, tickstart, USART_TEACK_REACK_TIMEOUT) != HAL_OK) | |
{ | |
/* Timeout occurred */ | |
return HAL_TIMEOUT; | |
} | |
} | |
} | |
#endif /* !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC) */ | |
/* Initialize the USART state*/ | |
husart->State= HAL_USART_STATE_READY; | |
/* Process Unlocked */ | |
__HAL_UNLOCK(husart); | |
return HAL_OK; | |
} | |
/** | |
* @brief Simplex send an amount of data in non-blocking mode. | |
* @note Function called under interruption only, once | |
* interruptions have been enabled by HAL_USART_Transmit_IT(). | |
* @note The USART errors are not managed to avoid the overrun error. | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_Transmit_IT(USART_HandleTypeDef *husart) | |
{ | |
uint16_t* tmp=0U; | |
/* Check that a Tx process is ongoing */ | |
if(husart->State == HAL_USART_STATE_BUSY_TX) | |
{ | |
if(husart->TxXferCount == 0U) | |
{ | |
/* Disable the USART Transmit data register empty interrupt */ | |
__HAL_USART_DISABLE_IT(husart, USART_IT_TXE); | |
/* Enable the USART Transmit Complete Interrupt */ | |
__HAL_USART_ENABLE_IT(husart, USART_IT_TC); | |
return HAL_OK; | |
} | |
else | |
{ | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) husart->pTxBuffPtr; | |
husart->Instance->TDR = (*tmp & (uint16_t)0x01FFU); | |
husart->pTxBuffPtr += 2U; | |
} | |
else | |
{ | |
husart->Instance->TDR = (uint8_t)(*husart->pTxBuffPtr++ & (uint8_t)0xFFU); | |
} | |
husart->TxXferCount--; | |
return HAL_OK; | |
} | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Wraps up transmission in non-blocking mode. | |
* @param husart Pointer to a USART_HandleTypeDef structure that contains | |
* the configuration information for the specified USART module. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_EndTransmit_IT(USART_HandleTypeDef *husart) | |
{ | |
/* Disable the USART Transmit Complete Interrupt */ | |
__HAL_USART_DISABLE_IT(husart, USART_IT_TC); | |
/* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
__HAL_USART_DISABLE_IT(husart, USART_IT_ERR); | |
/* Tx process is ended, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
HAL_USART_TxCpltCallback(husart); | |
return HAL_OK; | |
} | |
/** | |
* @brief Simplex receive an amount of data in non-blocking mode. | |
* @note Function called under interruption only, once | |
* interruptions have been enabled by HAL_USART_Receive_IT(). | |
* @param husart USART handle | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_Receive_IT(USART_HandleTypeDef *husart) | |
{ | |
uint16_t* tmp=0U; | |
uint16_t uhMask = husart->Mask; | |
if(husart->State == HAL_USART_STATE_BUSY_RX) | |
{ | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) husart->pRxBuffPtr; | |
*tmp = (uint16_t)(husart->Instance->RDR & uhMask); | |
husart->pRxBuffPtr += 2U; | |
} | |
else | |
{ | |
*husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); | |
} | |
/* Send dummy byte in order to generate the clock for the Slave to Send the next data */ | |
husart->Instance->TDR = (USART_DUMMY_DATA & (uint16_t)0x00FFU); | |
if(--husart->RxXferCount == 0U) | |
{ | |
/* Disable the USART Parity Error Interrupt and RXNE interrupt*/ | |
CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); | |
/* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Rx process is completed, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
HAL_USART_RxCpltCallback(husart); | |
return HAL_OK; | |
} | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @brief Full-Duplex Send receive an amount of data in full-duplex mode (non-blocking). | |
* @note Function called under interruption only, once | |
* interruptions have been enabled by HAL_USART_TransmitReceive_IT(). | |
* @param husart USART handle. | |
* @retval HAL status | |
*/ | |
static HAL_StatusTypeDef USART_TransmitReceive_IT(USART_HandleTypeDef *husart) | |
{ | |
uint16_t* tmp=0U; | |
uint16_t uhMask = husart->Mask; | |
if(husart->State == HAL_USART_STATE_BUSY_TX_RX) | |
{ | |
if(husart->TxXferCount != 0x00U) | |
{ | |
if(__HAL_USART_GET_FLAG(husart, USART_FLAG_TXE) != RESET) | |
{ | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) husart->pTxBuffPtr; | |
husart->Instance->TDR = (uint16_t)(*tmp & uhMask); | |
husart->pTxBuffPtr += 2U; | |
} | |
else | |
{ | |
husart->Instance->TDR = (uint8_t)(*husart->pTxBuffPtr++ & (uint8_t)uhMask); | |
} | |
husart->TxXferCount--; | |
/* Check the latest data transmitted */ | |
if(husart->TxXferCount == 0U) | |
{ | |
__HAL_USART_DISABLE_IT(husart, USART_IT_TXE); | |
} | |
} | |
} | |
if(husart->RxXferCount != 0x00U) | |
{ | |
if(__HAL_USART_GET_FLAG(husart, USART_FLAG_RXNE) != RESET) | |
{ | |
if((husart->Init.WordLength == USART_WORDLENGTH_9B) && (husart->Init.Parity == USART_PARITY_NONE)) | |
{ | |
tmp = (uint16_t*) husart->pRxBuffPtr; | |
*tmp = (uint16_t)(husart->Instance->RDR & uhMask); | |
husart->pRxBuffPtr += 2U; | |
} | |
else | |
{ | |
*husart->pRxBuffPtr++ = (uint8_t)(husart->Instance->RDR & (uint8_t)uhMask); | |
} | |
husart->RxXferCount--; | |
} | |
} | |
/* Check the latest data received */ | |
if(husart->RxXferCount == 0U) | |
{ | |
/* Disable the USART Parity Error Interrupt and RXNE interrupt*/ | |
CLEAR_BIT(husart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); | |
/* Disable the USART Error Interrupt: (Frame error, noise error, overrun error) */ | |
CLEAR_BIT(husart->Instance->CR3, USART_CR3_EIE); | |
/* Rx process is completed, restore husart->State to Ready */ | |
husart->State = HAL_USART_STATE_READY; | |
HAL_USART_TxRxCpltCallback(husart); | |
return HAL_OK; | |
} | |
return HAL_OK; | |
} | |
else | |
{ | |
return HAL_BUSY; | |
} | |
} | |
/** | |
* @} | |
*/ | |
#endif /* HAL_USART_MODULE_ENABLED */ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |