blob: cd03b97405d3bc0297f0de4821f22e4727e66c7a [file] [log] [blame]
/*
* Copyright (c) 2014-2015 Wind River Systems, Inc.
* Copyright (c) 2016, Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: Apache-2.0
*/
/**
* @file
* @brief System/hardware module for fsl_frdm_k64f platform
*
* This module provides routines to initialize and support board-level
* hardware for the fsl_frdm_k64f platform.
*/
#include <kernel.h>
#include <device.h>
#include <init.h>
#include <soc.h>
#include <uart.h>
#include <linker/sections.h>
#include <fsl_common.h>
#include <fsl_clock.h>
#include <arch/cpu.h>
#include <cortex_m/exc.h>
#define PLLFLLSEL_MCGFLLCLK (0)
#define PLLFLLSEL_MCGPLLCLK (1)
#define PLLFLLSEL_IRC48MHZ (3)
#define ER32KSEL_OSC32KCLK (0)
#define ER32KSEL_RTC (2)
#define ER32KSEL_LPO1KHZ (3)
#define TIMESRC_OSCERCLK (2)
/*
* K64F Flash configuration fields
* These 16 bytes, which must be loaded to address 0x400, include default
* protection and security settings.
* They are loaded at reset to various Flash Memory module (FTFE) registers.
*
* The structure is:
* -Backdoor Comparison Key for unsecuring the MCU - 8 bytes
* -Program flash protection bytes, 4 bytes, written to FPROT0-3
* -Flash security byte, 1 byte, written to FSEC
* -Flash nonvolatile option byte, 1 byte, written to FOPT
* -Reserved, 1 byte, (Data flash protection byte for FlexNVM)
* -Reserved, 1 byte, (EEPROM protection byte for FlexNVM)
*
*/
u8_t __kinetis_flash_config_section __kinetis_flash_config[] = {
/* Backdoor Comparison Key (unused) */
0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
/* Program flash protection; 1 bit/region - 0=protected, 1=unprotected
*/
0xFF, 0xFF, 0xFF, 0xFF,
/*
* Flash security: Backdoor key disabled, Mass erase enabled,
* Factory access enabled, MCU is unsecure
*/
0xFE,
/* Flash nonvolatile option: NMI enabled, EzPort enabled, Normal boot */
0xFF,
/* Reserved for FlexNVM feature (unsupported by this MCU) */
0xFF, 0xFF};
static const osc_config_t oscConfig = {
.freq = CONFIG_OSC_XTAL0_FREQ,
.capLoad = 0,
#if defined(CONFIG_OSC_EXTERNAL)
.workMode = kOSC_ModeExt,
#elif defined(CONFIG_OSC_LOW_POWER)
.workMode = kOSC_ModeOscLowPower,
#elif defined(CONFIG_OSC_HIGH_GAIN)
.workMode = kOSC_ModeOscHighGain,
#else
#error "An oscillator mode must be defined"
#endif
.oscerConfig = {
.enableMode = kOSC_ErClkEnable,
#if (defined(FSL_FEATURE_OSC_HAS_EXT_REF_CLOCK_DIVIDER) && \
FSL_FEATURE_OSC_HAS_EXT_REF_CLOCK_DIVIDER)
.erclkDiv = 0U,
#endif
},
};
static const mcg_pll_config_t pll0Config = {
.enableMode = 0U,
.prdiv = CONFIG_MCG_PRDIV0,
.vdiv = CONFIG_MCG_VDIV0,
};
static const sim_clock_config_t simConfig = {
.pllFllSel = PLLFLLSEL_MCGPLLCLK, /* PLLFLLSEL select PLL. */
.er32kSrc = ER32KSEL_RTC, /* ERCLK32K selection, use RTC. */
.clkdiv1 = SIM_CLKDIV1_OUTDIV1(CONFIG_K64_CORE_CLOCK_DIVIDER - 1) |
SIM_CLKDIV1_OUTDIV2(CONFIG_K64_BUS_CLOCK_DIVIDER - 1) |
SIM_CLKDIV1_OUTDIV3(CONFIG_K64_FLEXBUS_CLOCK_DIVIDER - 1) |
SIM_CLKDIV1_OUTDIV4(CONFIG_K64_FLASH_CLOCK_DIVIDER - 1),
};
/**
*
* @brief Initialize the system clock
*
* This routine will configure the multipurpose clock generator (MCG) to
* set up the system clock.
* The MCG has nine possible modes, including Stop mode. This routine assumes
* that the current MCG mode is FLL Engaged Internal (FEI), as from reset.
* It transitions through the FLL Bypassed External (FBE) and
* PLL Bypassed External (PBE) modes to get to the desired
* PLL Engaged External (PEE) mode and generate the maximum 120 MHz system
* clock.
*
* @return N/A
*
*/
static ALWAYS_INLINE void clkInit(void)
{
CLOCK_SetSimSafeDivs();
CLOCK_InitOsc0(&oscConfig);
CLOCK_SetXtal0Freq(CONFIG_OSC_XTAL0_FREQ);
CLOCK_BootToPeeMode(kMCG_OscselOsc, kMCG_PllClkSelPll0, &pll0Config);
CLOCK_SetInternalRefClkConfig(kMCG_IrclkEnable, kMCG_IrcSlow,
CONFIG_MCG_FCRDIV);
CLOCK_SetSimConfig(&simConfig);
#if CONFIG_ETH_MCUX
CLOCK_SetEnetTime0Clock(TIMESRC_OSCERCLK);
#endif
#if CONFIG_USB_KINETIS
CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcPll0,
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC);
#endif
}
/**
*
* @brief Perform basic hardware initialization
*
* Initialize the interrupt controller device drivers.
* Also initialize the timer device driver, if required.
*
* @return 0
*/
static int fsl_frdm_k64f_init(struct device *arg)
{
ARG_UNUSED(arg);
unsigned int oldLevel; /* old interrupt lock level */
#if !defined(CONFIG_ARM_MPU)
u32_t temp_reg;
#endif /* !CONFIG_ARM_MPU */
/* disable interrupts */
oldLevel = irq_lock();
/* release I/O power hold to allow normal run state */
PMC->REGSC |= PMC_REGSC_ACKISO_MASK;
#if !defined(CONFIG_ARM_MPU)
/*
* Disable memory protection and clear slave port errors.
* Note that the K64F does not implement the optional ARMv7-M memory
* protection unit (MPU), specified by the architecture (PMSAv7), in the
* Cortex-M4 core. Instead, the processor includes its own MPU module.
*/
temp_reg = SYSMPU->CESR;
temp_reg &= ~SYSMPU_CESR_VLD_MASK;
temp_reg |= SYSMPU_CESR_SPERR_MASK;
SYSMPU->CESR = temp_reg;
#endif /* !CONFIG_ARM_MPU */
_ClearFaults();
/* Initialize PLL/system clock to 120 MHz */
clkInit();
/*
* install default handler that simply resets the CPU
* if configured in the kernel, NOP otherwise
*/
NMI_INIT();
/* restore interrupt state */
irq_unlock(oldLevel);
return 0;
}
SYS_INIT(fsl_frdm_k64f_init, PRE_KERNEL_1, 0);