| # Copyright 2019,2024 NXP |
| # SPDX-License-Identifier: Apache-2.0 |
| |
| if SOC_SERIES_LPC55XXX |
| |
| config NUM_IRQS |
| # must be >= the highest interrupt number used |
| default 60 |
| |
| config SYS_CLOCK_HW_CYCLES_PER_SEC |
| default 144000000 if INIT_PLL1 |
| default 96000000 |
| |
| # Indicates the second core will be enabled, and the part will run |
| # in dual core mode. |
| config SECOND_CORE_MCUX |
| depends on HAS_MCUX |
| |
| # Workaround for not being able to have commas in macro arguments |
| DT_CHOSEN_Z_CODE_CPU1_PARTITION := zephyr,code-cpu1-partition |
| |
| |
| # Move the LMA for the second core image to be in the flash region of primary |
| # core, so that JLink flash will load it correctly. |
| config BUILD_OUTPUT_ADJUST_LMA |
| depends on SECOND_CORE_MCUX && SOC_LPC55S69_CPU1 |
| default "0x10000000" |
| |
| # SRAM controllers 1,2,3, and 4 are disabled at reset. |
| # By default, CMSIS SystemInit will enable the clock to these RAM banks. |
| # Disable this Kconfig to leave the ram banks untouched out of reset. |
| config LPC55XXX_SRAM_CLOCKS |
| default y |
| |
| # Some SoC's in the LPC5500 Series do have a dedicated USB RAM. |
| # By default, USB RAM is assumed to be present. |
| # Disable this Kconfig in case there is no dedicated USB RAM. |
| config LPC55XXX_USB_RAM |
| default y |
| |
| if SOC_LPC55S06 |
| |
| config LPC55XXX_USB_RAM |
| default n |
| |
| endif # SOC_LPC55S06 |
| |
| if SOC_LPC55S16 |
| |
| config CAN_MCUX_MCAN |
| default y |
| depends on CAN |
| |
| choice USB_MCUX_CONTROLLER_TYPE |
| default USB_DC_NXP_LPCIP3511 |
| endchoice |
| |
| endif # SOC_LPC55S16 |
| |
| if SOC_LPC55S28 |
| |
| choice USB_MCUX_CONTROLLER_TYPE |
| default USB_DC_NXP_LPCIP3511 |
| endchoice |
| |
| endif # SOC_LPC55S28 |
| |
| if SOC_LPC55S36 |
| |
| choice USB_MCUX_CONTROLLER_TYPE |
| default USB_DC_NXP_LPCIP3511 |
| endchoice |
| |
| config LPC55XXX_USB_RAM |
| default n |
| |
| endif # SOC_LPC55S36 |
| |
| if SOC_LPC55S69 |
| |
| config SOC_FLASH_MCUX |
| default y |
| depends on FLASH |
| depends on !TRUSTED_EXECUTION_NONSECURE |
| |
| choice USB_MCUX_CONTROLLER_TYPE |
| default USB_DC_NXP_LPCIP3511 |
| endchoice |
| |
| config I2S_MCUX_FLEXCOMM |
| select INIT_PLL0 |
| |
| endif # SOC_LPC55S69 |
| |
| if SOC_LPC55S69_CPU1 |
| |
| |
| config GPIO |
| default y |
| |
| config SERIAL |
| default n |
| |
| endif # SOC_LPC55S69_CPU1 |
| |
| endif # SOC_SERIES_LPC55XXX |
