| .. zephyr:board:: mimxrt1180_evk |
| |
| Overview |
| ******** |
| |
| The dual core i.MX RT1180 runs on the Cortex-M33 core at 240 MHz and on the |
| Cortex-M7 at 792 MHz. The i.MX RT1180 MCU offers support over a wide |
| temperature range and is qualified for consumer, industrial and automotive |
| markets. |
| |
| Hardware |
| ******** |
| |
| - MIMXRT1189CVM8B MCU |
| |
| - 240MHz Cortex-M33 & 792Mhz Cortex-M7 |
| - 1.5MB SRAM with 512KB of TCM for Cortex-M7 and 256KB of TCM for Cortex-M4 |
| |
| - Memory |
| |
| - 512 Mbit SDRAM |
| - 128 Mbit QSPI Flash |
| - 512 Mbit HYPER RAM |
| - TF socket for SD card |
| |
| - Ethernet |
| |
| - 1000 Mbit/s Ethernet PHY |
| |
| - USB |
| |
| - 2* USB 2.0 OTG connector |
| |
| - Audio |
| |
| - 3.5 mm audio stereo headphone jack |
| - Board-mounted microphone |
| - Left and right speaker out connectors |
| |
| - Power |
| |
| - 5 V DC jack |
| |
| - Debug |
| |
| - JTAG 20-pin connector |
| - MCU-Link with DAPLink |
| |
| - Expansion port |
| |
| - Arduino interface |
| |
| - CAN bus connector |
| |
| For more information about the MIMXRT1180 SoC and MIMXRT1180-EVK board, see |
| these references: |
| |
| - `i.MX RT1180 Website`_ |
| - `MIMXRT1180-EVK Website`_ |
| |
| External Memory |
| =============== |
| |
| This platform has the following external memories: |
| |
| +--------------------+------------+-------------------------------------+ |
| | Device | Controller | Status | |
| +====================+============+=====================================+ |
| | W9825G6KH | SEMC | Enabled via device configuration | |
| | | | data block, which sets up SEMC at | |
| | | | boot time | |
| +--------------------+------------+-------------------------------------+ |
| | W25Q128JWSIQ | FLEXSPI | Enabled via flash configuration | |
| | | | block, which sets up FLEXSPI at | |
| | | | boot time. | |
| +--------------------+------------+-------------------------------------+ |
| |
| Supported Features |
| ================== |
| |
| NXP considers the MIMXRT1180-EVK as the superset board for the i.MX RT118x |
| family of MCUs. This board is a focus for NXP's Full Platform Support for |
| Zephyr, to better enable the entire RT118x family. NXP prioritizes enabling |
| this board with new support for Zephyr features. |
| |
| .. zephyr:board-supported-hw:: |
| |
| Connections and I/Os |
| ==================== |
| |
| The MIMXRT1180 SoC has six pairs of pinmux/gpio controllers. |
| |
| +---------------+-----------------+---------------------------+ |
| | Name | Function | Usage | |
| +===============+=================+===========================+ |
| | GPIO_AON_04 | GPIO | SW8 | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AD_27 | GPIO | LED | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AON_08 | LPUART1_TX | UART Console M33 core | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AON_09 | LPUART1_RX | UART Console M33 core | |
| +---------------+---------------------------------------------+ |
| | GPIO_AON_19 | LPUART12_TX | UART Console M7 core | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AON_20 | LPUART12_RX | UART Console M7 core | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_SD_B1_00 | SPI1_CS0 | spi | |
| +---------------+---------------------------------------------+ |
| | GPIO_SD_B1_01 | SPI1_CLK | spi | |
| +---------------+---------------------------------------------+ |
| | GPIO_SD_B1_02 | SPI1_SDO | spi | |
| +---------------+---------------------------------------------+ |
| | GPIO_SD_B1_03 | SPI1_SDI | spi | |
| +---------------+-----------------+---------------------------+ |
| |
| UART for M7 core is connected to USB-to-UART J60 connector. |
| Or user can use open JP7 Jumper to enable second UART on MCU LINK J53 connector. |
| |
| System Clock |
| ============ |
| |
| The MIMXRT1180 SoC is configured to use SysTick as the system clock source, |
| running at 240MHz. When targeting the M7 core, SysTick will also be used, |
| running at 792MHz |
| |
| Serial Port |
| =========== |
| |
| The MIMXRT1180 SoC has 12 UARTs. LPUART1 is configured for the CM33 console, the LPUART12 is |
| configured for the CM7 console core and the remaining are not used. |
| |
| Ethernet |
| ======== |
| |
| NETC Ethernet driver supports to manage the Physical Station Interface (PSI). |
| NETC DSA driver supports to manage switch ports. Current DSA support is with |
| limitation that only switch function is available without management via |
| DSA master port. DSA master port support is TODO work. |
| |
| .. code-block:: none |
| |
| +--------+ +--------+ |
| | ENETC1 | | ENETC0 | |
| | | | | |
| | Pseudo | | 1G | |
| | MAC | | MAC | |
| +--------+ +--------+ |
| | zero copy interface | |
| +-------------- +--------+----------------+ | |
| | | Pseudo | | | |
| | | MAC | | | |
| | | | | | |
| | | Port 4 | | | |
| | +--------+ | | |
| | SWITCH CORE | | |
| +--------+ +--------+ +--------+ +--------+ | |
| | Port 0 | | Port 1 | | Port 2 | | Port 3 | | |
| | | | | | | | | | |
| | 1G | | 1G | | 1G | | 1G | | |
| | MAC | | MAC | | MAC | | MAC | | |
| +--------+-+--------+-+--------+-+--------+ | |
| | | | | | |
| NETC External Interfaces (4 switch ports, 1 end-point port) |
| |
| Programming and Debugging |
| ************************* |
| |
| .. zephyr:board-supported-runners:: |
| |
| Build and flash applications as usual (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Configuring a Debug Probe |
| ========================= |
| |
| LinkServer is the default runner for this board. |
| A debug probe is used for both flashing and debugging the board. This board is |
| configured by default to use the :ref:`mcu-link-cmsis-onboard-debug-probe`. |
| The :ref:`pyocd-debug-host-tools` do not yet support programming the |
| external flashes on this board. Use one of the other supported debug probes |
| below. |
| |
| .. _Using J-Link RT1180: |
| |
| Using J-Link |
| ------------ |
| |
| Please ensure to use a version of JLINK above V7.94g and jumper JP5 is installed if using |
| external jlink plus on J37 as debugger. |
| |
| When debugging cm33 core, need to ensure the SW5 on "0100" mode. |
| When debugging cm7 core, need to ensure the SW5 on "0001" mode. |
| (Only support run cm7 image when debugging due to default boot core on board is cm33 core) |
| |
| Install the :ref:`jlink-debug-host-tools` and make sure they are in your search |
| path. |
| |
| There are two options: the onboard debug circuit can be updated with Segger |
| J-Link firmware, or :ref:`jlink-external-debug-probe` can be attached to the |
| EVK. |
| |
| |
| Using Linkserver |
| ---------------- |
| |
| Please ensure to use a version of Linkserver above V1.5.30 and jumper JP5 is uninstalled (default setting). |
| |
| When debugging cm33 core, need to ensure the SW5 on "0100" mode. |
| When debugging cm7 core, need to ensure the SW5 on "0001" mode. |
| (Only support run cm7 image when debugging due to default boot core on board is cm33 core) |
| |
| Dual Core samples Debugging |
| *************************** |
| |
| When debugging dual core samples, need to ensure the SW5 on "0100" mode. |
| The CM33 core is responsible for copying and starting the CM7. |
| To debug the CM7 it is useful to put infinite while loop either in reset vector or |
| into main function and attach via debugger to CM7 core. |
| |
| CM7 core can be started again only after reset, so after flashing ensure to reset board. |
| |
| Configuring a Console |
| ===================== |
| |
| Regardless of your choice in debug probe, we will use the MCU-Link |
| microcontroller as a usb-to-serial adapter for the serial console. Check that |
| jumpers JP5 and JP3 are **on** (they are on by default when boards ship from |
| the factory) to connect UART signals to the MCU-Link microcontroller. |
| |
| Connect a USB cable from your PC to J53. |
| |
| Use the following settings with your serial terminal of choice (minicom, putty, |
| etc.): |
| |
| - Speed: 115200 |
| - Data: 8 bits |
| - Parity: None |
| - Stop bits: 1 |
| |
| Flashing |
| ======== |
| |
| Here is an example for the :zephyr:code-sample:`hello_world` application on cm33 core. |
| |
| Before power on the board, make sure SW5 is set to 0100b |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: mimxrt1180_evk/mimxrt1189/cm33 |
| :goals: flash |
| |
| Power off the board, then power on the board and |
| open a serial terminal, reset the board (press the SW3 button), and you should |
| see the following message in the terminal: |
| |
| .. code-block:: console |
| |
| ***** Booting Zephyr OS v3.7.0-xxx-xxxxxxxxxxxxx ***** |
| Hello World! mimxrt1180_evk/mimxrt1189/cm33 |
| |
| Debugging |
| ========= |
| |
| Here is an example for the :zephyr:code-sample:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: mimxrt1180_evk/mimxrt1189/cm33 |
| :goals: debug |
| |
| Open a serial terminal, step through the application in your debugger, and you |
| should see the following message in the terminal: |
| |
| .. code-block:: console |
| |
| ***** Booting Zephyr OS v3.7.0-xxx-xxxxxxxxxxxxx ***** |
| Hello World! mimxrt1180_evk/mimxrt1189/cm33 |
| |
| .. include:: ../../common/board-footer.rst |
| :start-after: nxp-board-footer |
| |
| .. _MIMXRT1180-EVK Website: |
| https://www.nxp.com/design/design-center/development-boards-and-designs/i-mx-evaluation-and-development-boards/i-mx-rt1180-evaluation-kit:MIMXRT1180-EVK |
| |
| .. _i.MX RT1180 Website: |
| https://www.nxp.com/products/processors-and-microcontrollers/arm-microcontrollers/i-mx-rt-crossover-mcus/i-mx-rt1180-crossover-mcu-with-tsn-switch-and-edgelock:i.MX-RT1180 |
