boards/st/nucleo_wb07cc/nucleo_wb07cc.dts

/*
 * Copyright (c) 2025 STMicroelectronics
 *
 * SPDX-License-Identifier: Apache-2.0
 */

/dts-v1/;
#include <st/wb0/stm32wb07Xc.dtsi>
#include <st/wb0/stm32wb07ccvx-pinctrl.dtsi>
#include <zephyr/dt-bindings/input/input-event-codes.h>

#include "arduino_r3_connector.dtsi"

/ {
	model = "STMicroelectronics STM32WB07CC-NUCLEO board";
	compatible = "st,stm32wb07cc-nucleo";

	#address-cells = <1>;
	#size-cells = <1>;

	chosen {
		zephyr,console = &usart1;
		zephyr,shell-uart = &usart1;
		zephyr,sram = &sram0;
		zephyr,flash = &flash0;
		zephyr,bt-c2h-uart = &usart1;
	};

	leds: leds {
		compatible ="gpio-leds";
		blue_led_1: led_0 {
			gpios = <&gpiob 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
		};
		green_led_1: led_1 {
			gpios = <&gpiob 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
		};
		red_led_1: led_2 {
			gpios = <&gpiob 2 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
		};
	};

	pwmleds: pwmleds {
		compatible = "pwm-leds";
		pwm_red_led_1: pwm_red_led_1 {
			pwms = <&pwm1 3 PWM_MSEC(20) PWM_POLARITY_NORMAL>;
		};
	};

	gpio_keys {
		compatible = "gpio-keys";
		user_button_1: button_0 {
			label = "SW1";
			gpios = <&gpioa 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
			zephyr,code = <INPUT_KEY_0>;
		};
		user_button_2: button_1 {
			label = "SW2";
			gpios = <&gpiob 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
			zephyr,code = <INPUT_KEY_1>;
		};
		user_button_3: button_2 {
			label = "SW3";
			gpios = <&gpiob 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
			zephyr,code = <INPUT_KEY_2>;
		};
	};

	aliases {
		rtc = &rtc;
		led0 = &blue_led_1;
		led1 = &green_led_1;
		led2 = &red_led_1;
		pwm-led0 = &pwm_red_led_1;
		sw0 = &user_button_1;
		sw1 = &user_button_2;
		sw2 = &user_button_3;
		watchdog0 = &iwdg;
	};
};

&pwrc {
	smps-mode = "RUN";
	smps-bom = <3>;
};

&clk_lse {
	status = "okay";
};

&clk_hse {
	status = "okay";
};

&clk_hsi {
	status = "okay";
};

&pll {
	status = "okay";
};

&rcc {
	clocks = <&pll>;
	clock-frequency = <DT_FREQ_M(64)>;
	clksys-prescaler = <1>;
	slow-clock = <&clk_lse>;
};

&rtc {
	/**
	 * STM32_SRC_LSE reflects the "slow-clock" selected on RCC node.
	 * NO_SEL reflects STM32WB0's lack of RTC clock mux to configure.
	 */
	clocks = <&rcc STM32_CLOCK(APB0, 12)>,
		<&rcc STM32_SRC_LSE NO_SEL>;
	status = "okay";
};

&iwdg {
	status = "okay";
};

&bt_hci_wb0 {
	status = "okay";
};

&usart1 {
	pinctrl-0 = <&usart1_tx_pa9 &usart1_rx_pa8>;
	pinctrl-names = "default";
	current-speed = <115200>;
	status = "okay";
};

&i2c2 {
	pinctrl-0 = <&i2c2_scl_pb6 &i2c2_sda_pb7>;
	pinctrl-names = "default";
	status = "okay";
};

&spi2 {
	pinctrl-0 = <&spi2_nss_pa4 &spi2_sck_pa5 &spi2_miso_pa7 &spi2_mosi_pa6>;
	pinctrl-names = "default";
	status = "okay";
	/* Select 32MHz clock for SPI2 */
	clocks = <&rcc STM32_CLOCK(APB1, 12)>,
		<&rcc STM32_SRC_SYSCLK SPI2_I2S2_SEL(1)>;
};

&timers1 {
	status = "okay";
	st,prescaler = <10000>;

	pwm1: pwm {
		status = "okay";
		pinctrl-0 = <&tim1_ch3_pb2>;
		pinctrl-names = "default";
	};
};

&flash0 {
	partitions {
		compatible = "fixed-partitions";
		#address-cells = <1>;
		#size-cells = <1>;
		/* Set aside 16KB of storage at the end of 256KB flash */
		storage_partition: partition@3c000 {
			label = "storage";
			reg = <0x0003c000 DT_SIZE_K(16)>;
		};
	};
};