| .. _mimxrt1015_evk: |
| |
| NXP MIMXRT1015-EVK |
| ################## |
| |
| Overview |
| ******** |
| |
| The i.MX RT1015 expands the i.MX RT crossover processor families by providing |
| high-performance feature set in low-cost LQFP packages, further simplifying |
| board design and layout for customers. The i.MX RT1015 runs on the Arm® |
| Cortex®-M7 core at 500 MHz. |
| |
| .. image:: ./mimxrt1015_evk.jpg |
| :width: 720px |
| :align: center |
| :alt: MIMXRT1015-EVK |
| |
| Hardware |
| ******** |
| |
| - MIMXRT1015DAF5A MCU |
| |
| - Memory |
| |
| - 128 Mbit QSPI Flash |
| |
| - Connectivity |
| |
| - Micro USB host and OTG connectors |
| - Arduino interface |
| |
| - Audio |
| |
| - Audio Codec |
| - 4-pole audio headphone jack |
| - External speaker connection |
| - Microphone |
| |
| - Debug |
| |
| - JTAG 10-pin connector |
| - OpenSDA with DAPLink |
| |
| For more information about the MIMXRT1015 SoC and MIMXRT1015-EVK board, see |
| these references: |
| |
| - `i.MX RT1015 Website`_ |
| - `i.MX RT1015 Datasheet`_ |
| - `i.MX RT1015 Reference Manual`_ |
| - `MIMXRT1015-EVK Website`_ |
| - `MIMXRT1015-EVK Quick Reference Guide`_ |
| - `MIMXRT1015-EVK Design Files`_ |
| |
| Supported Features |
| ================== |
| |
| The mimxrt1015_evk board configuration supports the following hardware |
| features: |
| |
| +-----------+------------+-------------------------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+=====================================+ |
| | NVIC | on-chip | nested vector interrupt controller | |
| +-----------+------------+-------------------------------------+ |
| | SYSTICK | on-chip | systick | |
| +-----------+------------+-------------------------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+-------------------------------------+ |
| | I2C | on-chip | i2c | |
| +-----------+------------+-------------------------------------+ |
| | UART | on-chip | serial port-polling; | |
| | | | serial port-interrupt | |
| +-----------+------------+-------------------------------------+ |
| | USB | on-chip | USB device | |
| +-----------+------------+-------------------------------------+ |
| |
| The default configuration can be found in the defconfig file: |
| ``boards/arm/mimxrt1015_evk/mimxrt1015_evk_defconfig`` |
| |
| Other hardware features are not currently supported by the port. |
| |
| Connections and I/Os |
| ==================== |
| |
| The MIMXRT1015 SoC has five pairs of pinmux/gpio controllers. |
| |
| +---------------+-----------------+---------------------------+ |
| | Name | Function | Usage | |
| +===============+=================+===========================+ |
| | GPIO_AD_B0_05 | GPIO | LED | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_EMC_09 | GPIO | SW4 | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AD_B0_06 | LPUART1_TX | UART Console | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AD_B0_07 | LPUART1_RX | UART Console | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_EMC_32 | LPUART4_TX | UART Console | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_EMC_33 | LPUART4_RX | UART Console | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AD_B1_15 | LPI2C1_SDA | I2C SDA | |
| +---------------+-----------------+---------------------------+ |
| | GPIO_AD_B1_14 | LPI2C1_CLK | I2C SCL | |
| +---------------+-----------------+---------------------------+ |
| |
| System Clock |
| ============ |
| |
| The MIMXRT1015 SoC is configured to use the 24 MHz external oscillator on the |
| board with the on-chip PLL to generate a 500 MHz core clock. |
| |
| Serial Port |
| =========== |
| |
| The MIMXRT1015 SoC has four UARTs. ``LPUART1`` is configured for the console, |
| and the remaining are not used. |
| |
| Programming and Debugging |
| ************************* |
| |
| Build and flash applications as usual (see :ref:`build_an_application` and |
| :ref:`application_run` for more details). |
| |
| Configuring a Debug Probe |
| ========================= |
| |
| A debug probe is used for both flashing and debugging the board. This board is |
| configured by default to use the :ref:`opensda-daplink-onboard-debug-probe`, |
| however the :ref:`pyocd-debug-host-tools` do not yet support programming the |
| external flashes on this board so you must reconfigure the board for one of the |
| following debug probes instead. |
| |
| :ref:`jlink-external-debug-probe` |
| ------------------------------------------- |
| |
| Install the :ref:`jlink-debug-host-tools` and make sure they are in your search |
| path. |
| |
| Attach a J-Link 10-pin connector to J55. Check that jumpers J47 and J48 are |
| **off** (they are on by default when boards ship from the factory) to ensure |
| SWD signals are disconnected from the OpenSDA microcontroller. |
| |
| Configuring a Console |
| ===================== |
| |
| Regardless of your choice in debug probe, we will use the OpenSDA |
| microcontroller as a usb-to-serial adapter for the serial console. Check that |
| jumpers J45 and J46 are **on** (they are on by default when boards ship from |
| the factory) to connect UART signals to the OpenSDA microcontroller. |
| |
| Connect a USB cable from your PC to J41. |
| |
| Use the following settings with your serial terminal of choice (minicom, putty, |
| etc.): |
| |
| - Speed: 115200 |
| - Data: 8 bits |
| - Parity: None |
| - Stop bits: 1 |
| |
| Flashing |
| ======== |
| |
| Here is an example for the :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: mimxrt1015_evk |
| :goals: flash |
| |
| Open a serial terminal, reset the board (press the SW9 button), and you should |
| see the following message in the terminal: |
| |
| .. code-block:: console |
| |
| ***** Booting Zephyr OS v1.14.0-rc1-1297-g312d75f2459e ***** |
| Hello World! mimxrt1015_evk |
| |
| |
| .. _MIMXRT1015-EVK Website: |
| https://www.nxp.com/support/developer-resources/run-time-software/i.mx-developer-resources/i.mx-rt1015-evaluation-kit:MIMXRT1015-EVK |
| |
| .. _MIMXRT1015-EVK Quick Reference Guide: |
| https://www.nxp.com/webapp/Download?colCode=IMXRT1015QSG |
| |
| .. _MIMXRT1015-EVK Design Files: |
| https://www.nxp.com/webapp/Download?colCode=MIMXRT1015-EVK-REVB-DS |
| |
| .. _i.MX RT1015 Website: |
| https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-rt-series/i.mx-rt1015-crossover-processor-with-arm-cortex-m7-core:i.MX-RT1015 |
| |
| .. _i.MX RT1015 Datasheet: |
| https://www.nxp.com/docs/en/data-sheet/IMXRT1015CEC.pdf |
| |
| .. _i.MX RT1015 Reference Manual: |
| https://www.nxp.com/webapp/Download?colCode=IMXRT1015RM |