blob: cf408d42184e48e3de29514fea6e215c87514c9e [file] [log] [blame]
/*
* Copyright (c) 2021 Nuvoton Technology Corporation.
*
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT nuvoton_npcx_watchdog
/**
* @file
* @brief Nuvoton NPCX watchdog modules driver
*
* This file contains the drivers of NPCX Watchdog module that generates the
* clocks and interrupts (T0 Timer) used for its callback functions in the
* system. It also provides watchdog reset signal generation in response to a
* failure detection. Please refer the block diagram for more detail.
*
* +---------------------+ +-----------------+
* LFCLK --->| T0 Prescale Counter |-+->| 16-Bit T0 Timer |--------> T0 Timer
* (32kHz) | (TWCP 1:32) | | | (TWDT0) | Event
* +---------------------+ | +-----------------+
* +---------------------------------+
* |
* | +-------------------+ +-----------------+
* +--->| Watchdog Prescale |--->| 8-Bit Watchdog |-----> Watchdog Event/Reset
* | (WDCP 1:32) | | Counter (WDCNT) | after n clocks
* +-------------------+ +-----------------+
*
*/
#include <assert.h>
#include <drivers/gpio.h>
#include <drivers/clock_control.h>
#include <drivers/watchdog.h>
#include <soc.h>
#include "soc_miwu.h"
#include <logging/log.h>
LOG_MODULE_REGISTER(wdt_npcx, CONFIG_WDT_LOG_LEVEL);
/* Watchdog operating frequency is fixed to LFCLK (32.768) kHz */
#define NPCX_WDT_CLK LFCLK
/*
* Maximum watchdog window time. Since the watchdog counter is 8-bits, maximum
* time supported by npcx watchdog is 256 * (32 * 32) / 32768 = 8 sec.
*/
#define NPCX_WDT_MAX_WND_TIME 8000UL
/*
* Minimum watchdog window time. Ensure we have waited at least 3 watchdog
* clocks since touching WD timer. 3 / (32768 / 1024) HZ = 93.75ms
*/
#define NPCX_WDT_MIN_WND_TIME 100UL
/* Timeout for reloading and restarting Timer 0. (Unit:ms) */
#define NPCX_T0CSR_RST_TIMEOUT 2
/* Timeout for stopping watchdog. (Unit:ms) */
#define NPCX_WATCHDOG_STOP_TIMEOUT 1
/* Device config */
struct wdt_npcx_config {
/* wdt controller base address */
uintptr_t base;
/* t0 timer wake-up input source configuration */
const struct npcx_wui t0out;
};
/* Driver data */
struct wdt_npcx_data {
/* Timestamp of touching watchdog last time */
int64_t last_watchdog_touch;
/* Timeout callback used to handle watchdog event */
wdt_callback_t cb;
/* Watchdog feed timeout in milliseconds */
uint32_t timeout;
/* Indicate whether a watchdog timeout is installed */
bool timeout_installed;
};
struct miwu_dev_callback miwu_cb;
/* Driver convenience defines */
#define DRV_CONFIG(dev) ((const struct wdt_npcx_config *)(dev)->config)
#define DRV_DATA(dev) ((struct wdt_npcx_data *)(dev)->data)
#define HAL_INSTANCE(dev) (struct twd_reg *)(DRV_CONFIG(dev)->base)
/* WDT local inline functions */
static inline int wdt_t0out_reload(const struct device *dev)
{
struct twd_reg *const inst = HAL_INSTANCE(dev);
uint64_t st;
/* Reload and restart T0 timer */
inst->T0CSR = (inst->T0CSR & ~BIT(NPCX_T0CSR_WDRST_STS)) |
BIT(NPCX_T0CSR_RST);
/* Wait for timer is loaded and restart */
st = k_uptime_get();
while (IS_BIT_SET(inst->T0CSR, NPCX_T0CSR_RST)) {
if (k_uptime_get() - st > NPCX_T0CSR_RST_TIMEOUT) {
/* RST bit is still set? */
if (IS_BIT_SET(inst->T0CSR, NPCX_T0CSR_RST)) {
LOG_ERR("Timeout: reload T0 timer!");
return -ETIMEDOUT;
}
}
}
return 0;
}
static inline int wdt_wait_stopped(const struct device *dev)
{
struct twd_reg *const inst = HAL_INSTANCE(dev);
uint64_t st;
st = k_uptime_get();
/* If watchdog is still running? */
while (IS_BIT_SET(inst->T0CSR, NPCX_T0CSR_WD_RUN)) {
if (k_uptime_get() - st > NPCX_WATCHDOG_STOP_TIMEOUT) {
/* WD_RUN bit is still set? */
if (IS_BIT_SET(inst->T0CSR, NPCX_T0CSR_WD_RUN)) {
LOG_ERR("Timeout: stop watchdog timer!");
return -ETIMEDOUT;
}
}
}
return 0;
}
/* WDT local functions */
static void wdt_t0out_isr(const struct device *dev, struct npcx_wui *wui)
{
struct wdt_npcx_data *const data = DRV_DATA(dev);
ARG_UNUSED(wui);
LOG_DBG("WDT reset will issue after %d delay cycle! WUI(%d %d %d)",
CONFIG_WDT_NPCX_DELAY_CYCLES, wui->table, wui->group, wui->bit);
/* Handle watchdog event here. */
if (data->cb) {
data->cb(dev, 0);
}
}
static void wdt_config_t0out_interrupt(const struct device *dev)
{
const struct wdt_npcx_config *const config = DRV_CONFIG(dev);
/* Initialize a miwu device input and its callback function */
npcx_miwu_init_dev_callback(&miwu_cb, &config->t0out, wdt_t0out_isr,
dev);
npcx_miwu_manage_dev_callback(&miwu_cb, true);
/*
* Configure the T0 wake-up event triggered from a rising edge
* on T0OUT signal.
*/
npcx_miwu_interrupt_configure(&config->t0out,
NPCX_MIWU_MODE_EDGE, NPCX_MIWU_TRIG_HIGH);
}
/* WDT api functions */
static int wdt_npcx_install_timeout(const struct device *dev,
const struct wdt_timeout_cfg *cfg)
{
struct wdt_npcx_data *const data = DRV_DATA(dev);
struct twd_reg *const inst = HAL_INSTANCE(dev);
/* If watchdog is already running */
if (IS_BIT_SET(inst->T0CSR, NPCX_T0CSR_WD_RUN)) {
return -EBUSY;
}
/* No window watchdog support */
if (cfg->window.min != 0) {
data->timeout_installed = false;
return -EINVAL;
}
/*
* Since the watchdog counter in npcx series is 8-bits, maximum time
* supported by it is 256 * (32 * 32) / 32768 = 8 sec. This makes the
* allowed range of 1-8000 in milliseconds. Check if the provided value
* is within this range.
*/
if (cfg->window.max > NPCX_WDT_MAX_WND_TIME || cfg->window.max == 0) {
data->timeout_installed = false;
return -EINVAL;
}
/* Save watchdog timeout */
data->timeout = cfg->window.max;
/* Install user timeout isr */
data->cb = cfg->callback;
data->timeout_installed = true;
return 0;
}
static int wdt_npcx_setup(const struct device *dev, uint8_t options)
{
struct twd_reg *const inst = HAL_INSTANCE(dev);
const struct wdt_npcx_config *const config = DRV_CONFIG(dev);
struct wdt_npcx_data *const data = DRV_DATA(dev);
int rv;
/* Disable irq of t0-out expired event first */
npcx_miwu_irq_disable(&config->t0out);
if (!data->timeout_installed) {
LOG_ERR("No valid WDT timeout installed");
return -EINVAL;
}
if (IS_BIT_SET(inst->T0CSR, NPCX_T0CSR_WD_RUN)) {
LOG_ERR("WDT timer is busy");
return -EBUSY;
}
if ((options & WDT_OPT_PAUSE_IN_SLEEP) != 0) {
LOG_ERR("WDT_OPT_PAUSE_IN_SLEEP is not supported");
return -ENOTSUP;
}
if ((options & WDT_OPT_PAUSE_HALTED_BY_DBG) != 0) {
LOG_ERR("WDT_OPT_PAUSE_HALTED_BY_DBG is not supported");
return -ENOTSUP;
}
/*
* One clock period of T0 timer is 32/32.768 KHz = 0.976 ms.
* Then the counter value is timeout/0.976 - 1.
*/
inst->TWDT0 = MAX(ceiling_fraction(data->timeout * NPCX_WDT_CLK,
32 * 1000) - 1, 1);
/* Configure 8-bit watchdog counter */
inst->WDCNT = MIN(ceiling_fraction(data->timeout, 32) +
CONFIG_WDT_NPCX_DELAY_CYCLES, 0xff);
LOG_DBG("WDT setup: TWDT0, WDCNT are %d, %d", inst->TWDT0, inst->WDCNT);
/* Reload and restart T0 timer */
rv = wdt_t0out_reload(dev);
/* Configure t0 timer interrupt and its isr. */
wdt_config_t0out_interrupt(dev);
/* Enable irq of t0-out expired event */
npcx_miwu_irq_enable(&config->t0out);
return rv;
}
static int wdt_npcx_disable(const struct device *dev)
{
const struct wdt_npcx_config *const config = DRV_CONFIG(dev);
struct wdt_npcx_data *const data = DRV_DATA(dev);
struct twd_reg *const inst = HAL_INSTANCE(dev);
/*
* Ensure we have waited at least 3 watchdog ticks before
* stopping watchdog
*/
while (k_uptime_get() - data->last_watchdog_touch <
NPCX_WDT_MIN_WND_TIME)
continue;
/*
* Stop and unlock watchdog by writing 87h, 61h and 63h
* sequence bytes to WDSDM register
*/
inst->WDSDM = 0x87;
inst->WDSDM = 0x61;
inst->WDSDM = 0x63;
/* Disable irq of t0-out expired event and mark it uninstalled */
npcx_miwu_irq_disable(&config->t0out);
data->timeout_installed = false;
/* Wait for watchdof is stopped. */
return wdt_wait_stopped(dev);
}
static int wdt_npcx_feed(const struct device *dev, int channel_id)
{
ARG_UNUSED(channel_id);
struct wdt_npcx_data *const data = DRV_DATA(dev);
struct twd_reg *const inst = HAL_INSTANCE(dev);
/* Feed watchdog by writing 5Ch to WDSDM */
inst->WDSDM = 0x5C;
data->last_watchdog_touch = k_uptime_get();
/* Reload and restart T0 timer */
return wdt_t0out_reload(dev);
}
/* WDT driver registration */
static const struct wdt_driver_api wdt_npcx_driver_api = {
.setup = wdt_npcx_setup,
.disable = wdt_npcx_disable,
.install_timeout = wdt_npcx_install_timeout,
.feed = wdt_npcx_feed,
};
static int wdt_npcx_init(const struct device *dev)
{
struct twd_reg *const inst = HAL_INSTANCE(dev);
#ifdef CONFIG_WDT_DISABLE_AT_BOOT
wdt_npcx_disable(dev);
#endif
/*
* TWCFG (Timer Watchdog Configuration) setting
* [7:6]- Reserved = 0
* [5] - WDSDME = 1: Feed watchdog by writing 5Ch to WDSDM
* [4] - WDCT0I = 1: Select T0IN as watchdog prescaler clock
* [3] - LWDCNT = 0: Don't lock WDCNT register
* [2] - LTWDT0 = 0: Don't lock TWDT0 register
* [1] - LTWCP = 0: Don't lock TWCP register
* [0] - LTWCFG = 0: Don't lock TWCFG register
*/
inst->TWCFG = BIT(NPCX_TWCFG_WDSDME) | BIT(NPCX_TWCFG_WDCT0I);
/* Disable early touch functionality */
inst->T0CSR = (inst->T0CSR & ~BIT(NPCX_T0CSR_WDRST_STS)) |
BIT(NPCX_T0CSR_TESDIS);
/*
* Plan clock frequency of T0 timer and watchdog timer as below:
* - T0 Timer freq is LFCLK/32 Hz
* - Watchdog freq is T0CLK/32 Hz (ie. LFCLK/1024 Hz)
*/
inst->WDCP = 0x05; /* Prescaler is 32 in Watchdog Timer */
inst->TWCP = 0x05; /* Prescaler is 32 in T0 Timer */
return 0;
}
static const struct wdt_npcx_config wdt_npcx_cfg_0 = {
.base = DT_INST_REG_ADDR(0),
.t0out = NPCX_DT_WUI_ITEM_BY_NAME(0, t0_out)
};
static struct wdt_npcx_data wdt_npcx_data_0;
DEVICE_DT_INST_DEFINE(0, wdt_npcx_init, NULL,
&wdt_npcx_data_0, &wdt_npcx_cfg_0,
PRE_KERNEL_1,
CONFIG_KERNEL_INIT_PRIORITY_DEFAULT,
&wdt_npcx_driver_api);