| # Kconfig - Bluetooth LE driver configuration options |
| |
| # |
| # Copyright (c) 2015 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| # |
| # Bluetooth options |
| # |
| menu "Bluetooth HCI Driver Options" |
| depends on BLUETOOTH |
| |
| config BLUETOOTH_UART |
| bool |
| default n |
| |
| choice |
| prompt "Bluetooth HCI driver" |
| depends on BLUETOOTH |
| default BLUETOOTH_H4 |
| |
| config BLUETOOTH_H4 |
| bool "H:4 UART" |
| select UART_INTERRUPT_DRIVEN |
| select BLUETOOTH_UART |
| help |
| Bluetooth H:4 UART driver. Requires hardware flow control |
| lines to be available. |
| |
| config BLUETOOTH_H5 |
| bool "H:5 UART [EXPERIMENTAL]" |
| select UART_INTERRUPT_DRIVEN |
| select BLUETOOTH_UART |
| help |
| Bluetooth three-wire (H:5) UART driver. Implementation of HCI |
| Three-Wire UART Transport Layer. |
| |
| config BLUETOOTH_NO_DRIVER |
| bool "No default HCI driver" |
| help |
| This is intended for unit tests where no internal driver |
| should be selected. |
| |
| endchoice |
| |
| config BLUETOOTH_DEBUG_DRIVER |
| bool "Bluetooth driver debug" |
| depends on BLUETOOTH_DEBUG && BLUETOOTH_UART |
| default n |
| help |
| This option enables debug support for the chosen |
| Bluetooth HCI driver |
| |
| config BLUETOOTH_UART_ON_DEV_NAME |
| string "Device Name of UART Device for Bluetooth" |
| default "UART_0" |
| depends on BLUETOOTH_UART |
| help |
| This option specifies the name of UART device to be used |
| for Bluetooth. |
| |
| config BLUETOOTH_UART_IRQ |
| int "IRQ of UART Device for Bluetooth" |
| depends on BLUETOOTH_UART |
| help |
| This option specifies the IRQ of UART device to be used |
| for Bluetooth. |
| |
| config BLUETOOTH_UART_IRQ_PRI |
| int "IRQ Priority of UART Device for Bluetooth" |
| depends on BLUETOOTH_UART |
| help |
| This option specifies the IRQ priority of UART device to be used |
| for Bluetooth. |
| |
| # Headroom that the driver needs for sending and receiving buffers. |
| # Add a new 'default' entry for each new driver. |
| |
| # Needed headroom for outgoing buffers (to controller) |
| config BLUETOOTH_HCI_SEND_RESERVE |
| int |
| depends on BLUETOOTH |
| default 0 if BLUETOOTH_H4 |
| default 1 if BLUETOOTH_H5 |
| # Even if no driver is selected the following default is still |
| # needed e.g. for unit tests. |
| default 0 |
| |
| # Needed headroom for incoming buffers (from controller) |
| config BLUETOOTH_HCI_RECV_RESERVE |
| int |
| depends on BLUETOOTH |
| default 0 if BLUETOOTH_H4 |
| default 0 if BLUETOOTH_H5 |
| # Even if no driver is selected the following default is still |
| # needed e.g. for unit tests. |
| default 0 |
| |
| endmenu |
