| # Kconfig - Modem configuration options |
| |
| # |
| # Copyright (c) 2018 Foundries.io |
| # |
| # SPDX-License-Identifier: Apache-2.0 |
| # |
| |
| menuconfig MODEM |
| bool "Modem Drivers" |
| help |
| Enable config options for modem drivers. |
| |
| if MODEM |
| |
| config MODEM_RECEIVER |
| bool "Enable modem receiver helper driver" |
| depends on SERIAL_SUPPORT_INTERRUPT |
| select UART_INTERRUPT_DRIVEN |
| help |
| This driver allows modem drivers to communicate over UART with custom |
| defined protocols. Driver doesn't inspect received data and all |
| aspects of received protocol data are handled by application via |
| work method provided. This driver differs from the pipe UART driver |
| in that callbacks are executed in a different work queue and data is |
| passed around in k_pipe structures. |
| |
| config MODEM_RECEIVER_MAX_CONTEXTS |
| int "Maximum number of modem receiver contexts" |
| depends on MODEM_RECEIVER |
| range 1 10 |
| default 1 |
| help |
| Maximum number of modem receiver contexts to handle. For most |
| purposes this should stay at 1. |
| |
| config MODEM_SHELL |
| bool "Enable modem shell utilities" |
| select SHELL |
| help |
| Activate shell module that provides modem utilities like |
| sending a command to the modem UART. |
| |
| config MODEM_WNCM14A2A |
| bool "Enable Wistron LTE-M modem driver" |
| select MODEM_RECEIVER |
| select NET_OFFLOAD |
| select UART_MCUX_2 if BOARD_FRDM_K64F |
| select GPIO_NRF_P1 if SOC_NRF52840 |
| select UART_1_NRF_UARTE if SOC_NRF52840 |
| select UART_1_NRF_FLOW_CONTROL if SOC_NRF52840 |
| help |
| Choose this setting to enable Wistron WNC-M14A2A LTE-M modem driver. |
| NOTE: Currently the pin settings only work with FRDM K64F shield. |
| |
| config MODEM_WNCM14A2A_RX_STACK_SIZE |
| int "Size of the stack for the WNC-M14A2A modem driver RX thread" |
| depends on MODEM_WNCM14A2A |
| default 1028 |
| help |
| This stack is used by the WNCM14A2A RX thread. |
| |
| config MODEM_WNCM14A2A_RX_WORKQ_STACK_SIZE |
| int "Size of the stack for the WNC-M14A2A modem driver work queue" |
| depends on MODEM_WNCM14A2A |
| default 2048 |
| help |
| This stack is used by the work queue to pass off net_pkt data |
| to the rest of the network stack, letting the rx thread continue |
| processing data. |
| |
| config MODEM_WNCM14A2A_APN_NAME |
| string "APN name for establishing network connection" |
| depends on MODEM_WNCM14A2A |
| default "m2m.com.attz" |
| help |
| This setting is used in the AT%PDNSET command to set the APN name |
| for the network connection context. Normally, don't need to change |
| this value. |
| |
| config MODEM_WNCM14A2A_INIT_PRIORITY |
| int "WNC-M14A2A driver init priority" |
| depends on MODEM_WNCM14A2A |
| default 80 |
| help |
| WNC-M14A2A device driver initialization priority. |
| Do not mess with it unless you know what you are doing. |
| Note that the priority needs to be lower than the net stack |
| so that it can start before the networking sub-system. |
| |
| module = MODEM |
| module-str = modem |
| source "subsys/logging/Kconfig.template.log_config" |
| |
| endif # MODEM |
