arch/arc/soc/quark_se_ss/Kconfig.defconfig

#
# Copyright (c) 2014 Wind River Systems, Inc.
# Copyright (c) 2015-2016 Intel Corporation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#

if SOC_QUARK_SE_SS

config SOC
	default quark_se_ss

config NUM_IRQ_PRIO_LEVELS
	# This processor supports only 2 priority levels:
	# 0 for Fast Interrupts (FIRQs) and 1 for Regular Interrupts (IRQs).
	default 2

config NUM_REGULAR_IRQ_PRIO_LEVELS
	# This processor supports only 1 Regular Interrupt priority level (1).
	default 1

config  NUM_IRQS
	# must be > the highest interrupt number used
	default 68


config SYS_CLOCK_HW_CYCLES_PER_SEC
	default 32000000

config RAM_START
	default 0x4000 if NSIM
	default 0xa8000400

config RAM_SIZE
	default 16 if NSIM
	default 24

if GPIO

config GPIO_DW
	def_bool y

if GPIO_DW

config GPIO_DW_BOTHEDGES_SUPPORT
	default n

config GPIO_DW_0
	def_bool y

if GPIO_DW_0

config GPIO_DW_0_BASE_ADDR
	default 0x80017800
config GPIO_DW_0_IRQ
	default 20
config GPIO_DW_0_PRI
	default 2
config GPIO_DW_0_BITS
	default 8

endif # GPIO_DW_0

config GPIO_DW_1
	def_bool y

if GPIO_DW_1

config GPIO_DW_1_BASE_ADDR
	default 0x80017900
config GPIO_DW_1_IRQ
	default 21
config GPIO_DW_1_PRI
	default 2
config GPIO_DW_1_BITS
	default 8

endif # GPIO_DW_1

endif # GPIO_DW

endif # GPIO

if I2C

config I2C_QUARK_SE_SS
	def_bool y

if I2C_QUARK_SE_SS

config I2C_QUARK_SE_SS_0
	def_bool y

if I2C_QUARK_SE_SS_0

config I2C_QUARK_SE_SS_0_BASE
	default 0x80012000

config I2C_QUARK_SE_SS_0_NAME
	default "I2C0"

config I2C_QUARK_SE_SS_0_DEFAULT_CFG
	default 0x12

endif # I2C_QUARK_SE_SS_0

if I2C_QUARK_SE_SS_1

config I2C_QUARK_SE_SS_1_BASE
	default 0x80012100

config I2C_QUARK_SE_SS_1_NAME
	default "I2C1"

config I2C_QUARK_SE_SS_1_DEFAULT_CFG
	default 0x12

endif # I2C_QUARK_SE_SS_1

endif # I2C_QUARK_SE_SS

endif # I2C

if UART_NS16550

config UART_NS16550_PORT_0
        def_bool y

if UART_NS16550_PORT_0

config UART_NS16550_PORT_0_NAME
        default "UART_0"
config UART_NS16550_PORT_0_BASE_ADDR
        default 0xB0002000
config UART_NS16550_PORT_0_IRQ
        default 41
config UART_NS16550_PORT_0_IRQ_PRI
        default 1
config UART_NS16550_PORT_0_BAUD_RATE
        default 115200
config UART_NS16550_PORT_0_CLK_FREQ
        default 32000000
config UART_NS16550_PORT_0_OPTIONS
        default 0

endif # UART_NS16550_PORT_0

config UART_NS16550_PORT_1
        def_bool y

if UART_NS16550_PORT_1

config UART_NS16550_PORT_1_NAME
        default "UART_1"
config UART_NS16550_PORT_1_BASE_ADDR
        default 0xB0002400
config UART_NS16550_PORT_1_IRQ
        default 42
config UART_NS16550_PORT_1_IRQ_PRI
        default 1
config UART_NS16550_PORT_1_BAUD_RATE
        default 115200
config UART_NS16550_PORT_1_CLK_FREQ
        default 32000000
config UART_NS16550_PORT_1_OPTIONS
        default 0

endif # UART_NS16550_PORT_1

endif # UART_NS16550

if UART_CONSOLE

config UART_CONSOLE_ON_DEV_NAME
        default "UART_1"

endif

if SPI

config SPI_DW
	def_bool y

if SPI_DW

config SPI_DW_CLOCK_GATE
	def_bool n

config SPI_DW_PORT_0
	def_bool y

if SPI_DW_PORT_0

config SPI_DW_PORT_0_PRI
	default 1
config SPI_DW_PORT_0_REGS
	default 0x80010000
config SPI_DW_PORT_0_ERROR_IRQ
	default 30
config SPI_DW_PORT_0_RX_IRQ
	default 31
config SPI_DW_PORT_0_TX_IRQ
	default 32

endif # SPI_DW_PORT_0

config SPI_DW_PORT_1
	def_bool y

if SPI_DW_PORT_1

config SPI_DW_PORT_1_PRI
	default 1
config SPI_DW_PORT_1_REGS
	default 0x80010100
config SPI_DW_PORT_1_ERROR_IRQ
	default 33
config SPI_DW_PORT_1_RX_IRQ
	default 34
config SPI_DW_PORT_1_TX_IRQ
	default 35

endif # SPI_DW_PORT_1

endif # SPI_DW

endif # SPI

config KERNEL_INIT_PRIORITY_DEFAULT
	default 40

config KERNEL_INIT_PRIORITY_DEVICE
	default 50

config IPM_CONSOLE_PRIORITY
	default 60 if IPM_CONSOLE_SENDER || IPM_CONSOLE_RECEIVER

config UART_CONSOLE_PRIORITY
	default 60 if UART_CONSOLE

config GPIO_DW_INIT_PRIORITY
	default 60 if GPIO_DW

config I2C_INIT_PRIORITY
	default 60 if I2C

config SPI_DW_INIT_PRIORITY
	# It might require GPIO to be ready first
	default 70 if SPI_DW

endif #SOC_QUARK_SE_ARC