| # Kconfig.sx9500 - SX9500 SAR proximity sensor configuration options |
| |
| # |
| # Copyright (c) 2016 Intel Corporation |
| # |
| # Licensed under the Apache License, Version 2.0 (the "License"); |
| # you may not use this file except in compliance with the License. |
| # You may obtain a copy of the License at |
| # |
| # http://www.apache.org/licenses/LICENSE-2.0 |
| # |
| # Unless required by applicable law or agreed to in writing, software |
| # distributed under the License is distributed on an "AS IS" BASIS, |
| # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| # See the License for the specific language governing permissions and |
| # limitations under the License. |
| # |
| |
| menuconfig SX9500 |
| bool "SX9500 I2C SAR Proximity Chip" |
| depends on SENSOR && I2C |
| default n |
| help |
| Enable driver for SX9500 I2C-based SAR proximity sensor. |
| |
| config SX9500_DEV_NAME |
| string "SX9500 device name" |
| depends on SX9500 |
| default "SX9500" |
| |
| config SX9500_INIT_PRIORITY |
| int |
| depends on SX9500 |
| default 70 |
| prompt "Init priority" |
| help |
| Device driver initialization priority. |
| |
| config SX9500_I2C_ADDR |
| hex "SX9500 I2C slave address" |
| depends on SX9500 |
| default 0x2B |
| help |
| Specify the I2C slave address for the SX9500. |
| |
| config SX9500_I2C_DEV_NAME |
| string "I2C master where SX9500 is connected" |
| depends on SX9500 |
| default "I2C0" |
| help |
| Specify the device name of the I2C master device to which SX9500 is |
| connected. |
| |
| config SX9500_PROX_CHANNEL |
| int |
| default 3 |
| depends on SX9500 |
| prompt "Proximity channel to use" |
| help |
| The SX9500 offers 4 separate proximity channels. Choose which one |
| you are using. Valid numbers are 0 to 3. |
| |
| choice |
| prompt "SX9500 trigger mode" |
| depends on SX9500 |
| default SX9500_TRIGGER_GLOBAL_FIBER |
| |
| config SX9500_TRIGGER_NONE |
| bool "No trigger" |
| |
| config SX9500_TRIGGER_GLOBAL_FIBER |
| depends on GPIO |
| select SX9500_TRIGGER |
| select SENSOR_DELAYED_WORK |
| bool "Use global fiber" |
| |
| config SX9500_TRIGGER_OWN_FIBER |
| depends on GPIO |
| select SX9500_TRIGGER |
| bool "Use own fiber" |
| |
| endchoice |
| |
| config SX9500_TRIGGER |
| bool |
| depends on SX9500 |
| |
| config SX9500_GPIO_CONTROLLER |
| string "GPIO controller for SX9500 interrupt" |
| depends on SX9500 && SX9500_TRIGGER |
| default GPIO_0 |
| help |
| Specify the device name of the GPIO controller the SX9500 interrupt |
| is connected to. |
| |
| config SX9500_GPIO_PIN |
| int "GPIO pin for SX9500 interrupt" |
| depends on SX9500 && SX9500_TRIGGER |
| default 3 |
| |
| config SX9500_FIBER_STACK_SIZE |
| int "Sensor delayed work fiber stack size" |
| depends on SX9500 && SX9500_TRIGGER_OWN_FIBER |
| default 1024 |
| |
| config SX9500_FIBER_PRIORITY |
| int "Fiber priority" |
| depends on SX9500 && SX9500_TRIGGER_OWN_FIBER |
| default 10 |
