| /* |
| * Copyright (c) 2015 Intel Corporation. |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| /** |
| * @file Board config file |
| */ |
| |
| #include <device.h> |
| #include <init.h> |
| |
| #include <nanokernel.h> |
| |
| #include "soc.h" |
| |
| #ifdef CONFIG_UART_K20 |
| #include <uart.h> |
| #include <drivers/k20_pcr.h> |
| #include <drivers/k20_sim.h> |
| #include <console/uart_console.h> |
| #include <serial/uart_k20_priv.h> |
| #endif /* CONFIG_UART_K20 */ |
| |
| /* |
| * UART configuration |
| */ |
| |
| #ifdef CONFIG_UART_K20 |
| |
| #if defined(CONFIG_UART_CONSOLE) |
| #if defined(CONFIG_PRINTK) || defined(CONFIG_STDOUT_CONSOLE) |
| |
| /** |
| * @brief Initialize K20 serial port as console |
| * |
| * Initialize the UART port for console I/O. |
| * |
| * @param dev The UART device struct |
| * |
| * @return 0 if successful, otherwise failed. |
| */ |
| static int uart_k20_console_init(struct device *dev) |
| { |
| uint32_t port; |
| uint32_t rxPin; |
| uint32_t txPin; |
| union K20_PCR pcr = {0}; /* Pin Control Register */ |
| |
| /* Port/pin ctrl module */ |
| volatile struct K20_PORT_PCR *port_pcr_p = |
| (volatile struct K20_PORT_PCR *)PERIPH_ADDR_BASE_PCR; |
| |
| /* UART0 Rx and Tx pin assignments */ |
| port = CONFIG_UART_CONSOLE_PORT; |
| rxPin = CONFIG_UART_CONSOLE_PORT_RX_PIN; |
| txPin = CONFIG_UART_CONSOLE_PORT_TX_PIN; |
| |
| /* Enable the UART Rx and Tx Pins */ |
| pcr.field.mux = CONFIG_UART_CONSOLE_PORT_MUX_FUNC; |
| |
| port_pcr_p->port[port].pcr[rxPin] = pcr; |
| port_pcr_p->port[port].pcr[txPin] = pcr; |
| |
| return 0; |
| } |
| |
| SYS_INIT(uart_k20_console_init, PRIMARY, CONFIG_KERNEL_INIT_PRIORITY_DEFAULT); |
| |
| #endif |
| #endif /* CONFIG_UART_CONSOLE */ |
| |
| static int uart_k20_init(struct device *dev) |
| { |
| volatile struct K20_SIM *sim = /* sys integ. ctl */ |
| (volatile struct K20_SIM *)PERIPH_ADDR_BASE_SIM; |
| SIM_SCGC4_t scgc4; |
| |
| ARG_UNUSED(dev); |
| |
| /* Although it is possible to modify the bits through |
| * *sim directly, the following code saves about 20 bytes |
| * of ROM space, compared to direct modification. |
| */ |
| scgc4.value = sim->scgc4.value; |
| |
| #ifdef CONFIG_UART_K20_PORT_0 |
| scgc4.field.uart0_clk_en = 1; |
| #endif |
| |
| #ifdef CONFIG_UART_K20_PORT_1 |
| scgc4.field.uart1_clk_en = 1; |
| #endif |
| |
| #ifdef CONFIG_UART_K20_PORT_2 |
| scgc4.field.uart2_clk_en = 1; |
| #endif |
| |
| #ifdef CONFIG_UART_K20_PORT_3 |
| scgc4.field.uart3_clk_en = 1; |
| #endif |
| |
| sim->scgc4.value = scgc4.value; |
| |
| #ifdef CONFIG_UART_K20_PORT_4 |
| sim->scgc1.field.uart4_clk_en = 1; |
| #endif |
| |
| return 0; |
| } |
| |
| DEVICE_INIT(_uart_k20_init, "", uart_k20_init, |
| NULL, NULL, |
| PRIMARY, CONFIG_KERNEL_INIT_PRIORITY_DEFAULT); |
| |
| #endif /* CONFIG_UART_K20 */ |