blob: 8404e58d94347108e78155eb5f1fc2a8fc55d9cc [file] [log] [blame]
# Kconfig - SHT3xD temperature and humidity sensor configuration options
#
# Copyright (c) 2016 Intel Corporation
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#
menuconfig SHT3XD
bool
prompt "SHT3xD Temperature and Humidity Sensor"
depends on SENSOR && I2C
default n
help
Enable driver for SHT3xD temperature and humidity sensors.
config SHT3XD_NAME
string
prompt "Driver name"
default "SHT3XD"
depends on SHT3XD
help
Device name with which the SHT3xD sensor is identified.
config SHT3XD_I2C_ADDR
hex "SHT3XD I2C address"
depends on SHT3XD
default "0x44"
help
I2C address of the SHT3xD sensor.
0x44: Choose this option if the ADDR pin is connected to VSS.
0x45: Choose this option if the ADDR pin is connected to VDD.
config SHT3XD_I2C_MASTER_DEV_NAME
string
prompt "I2C master where SHT3xD is connected"
depends on SHT3XD
default "I2C_0"
help
Specify the device name of the I2C master device to which the
SHT3xD chip is connected.
choice
prompt "Trigger mode"
depends on SHT3XD
default SHT3XD_TRIGGER_NONE
help
Specify the type of triggering to be used by the driver.
config SHT3XD_TRIGGER_NONE
bool
prompt "No trigger"
config SHT3XD_TRIGGER_GLOBAL_THREAD
bool
prompt "Use global thread"
depends on GPIO
select SHT3XD_TRIGGER
config SHT3XD_TRIGGER_OWN_THREAD
bool
prompt "Use own thread"
depends on GPIO
select SHT3XD_TRIGGER
endchoice
config SHT3XD_TRIGGER
bool
depends on SHT3XD
config SHT3XD_GPIO_DEV_NAME
string
prompt "GPIO device"
default "GPIO_0"
depends on SHT3XD && SHT3XD_TRIGGER
help
The device name of the GPIO device to which the SHT3xD interrupt
pins are connected.
config SHT3XD_GPIO_PIN_NUM
int
prompt "Interrupt GPIO pin number"
default 0
depends on SHT3XD && SHT3XD_TRIGGER
help
The number of the GPIO on which the interrupt signal from the
SHT3xD chip will be received.
config SHT3XD_THREAD_PRIORITY
int
prompt "Thread priority"
depends on SHT3XD && SHT3XD_TRIGGER_OWN_THREAD
default 10
help
Priority of thread used by the driver to handle interrupts.
config SHT3XD_THREAD_STACK_SIZE
int
prompt "Thread stack size"
depends on SHT3XD && SHT3XD_TRIGGER_OWN_THREAD
default 1024
help
Stack size of thread used by the driver to handle interrupts.
choice
prompt "Measurement repeatability"
depends on SHT3XD
default SHT3XD_REPEATABILITY_HIGH
help
Repeatability modes differ with respect to measurement duration,
noise level and energy consumption.
config SHT3XD_REPEATABILITY_LOW
bool
prompt "low"
config SHT3XD_REPEATABILITY_MEDIUM
bool
prompt "medium"
config SHT3XD_REPEATABILITY_HIGH
bool
prompt "high"
endchoice
choice
prompt "Measurements per second"
depends on SHT3XD
default SHT3XD_MPS_1
help
Number of measurements per second.
config SHT3XD_MPS_05
bool
prompt "0.5"
config SHT3XD_MPS_1
bool
prompt "1"
config SHT3XD_MPS_2
bool
prompt "2"
config SHT3XD_MPS_4
bool
prompt "4"
config SHT3XD_MPS_10
bool
prompt "10"
endchoice