| /* |
| * Copyright (c) 2015, Freescale Semiconductor, Inc. |
| * Copyright 2016-2017 NXP |
| * |
| * Redistribution and use in source and binary forms, with or without modification, |
| * are permitted provided that the following conditions are met: |
| * |
| * o Redistributions of source code must retain the above copyright notice, this list |
| * of conditions and the following disclaimer. |
| * |
| * o Redistributions in binary form must reproduce the above copyright notice, this |
| * list of conditions and the following disclaimer in the documentation and/or |
| * other materials provided with the distribution. |
| * |
| * o Neither the name of the copyright holder nor the names of its |
| * contributors may be used to endorse or promote products derived from this |
| * software without specific prior written permission. |
| * |
| * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND |
| * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED |
| * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE |
| * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES |
| * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; |
| * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON |
| * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT |
| * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS |
| * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |
| */ |
| |
| #ifndef _FSL_ADC16_H_ |
| #define _FSL_ADC16_H_ |
| |
| #include "fsl_common.h" |
| |
| /*! |
| * @addtogroup adc16 |
| * @{ |
| */ |
| |
| |
| /******************************************************************************* |
| * Definitions |
| ******************************************************************************/ |
| |
| /*! @name Driver version */ |
| /*@{*/ |
| /*! @brief ADC16 driver version 2.0.0. */ |
| #define FSL_ADC16_DRIVER_VERSION (MAKE_VERSION(2, 0, 0)) |
| /*@}*/ |
| |
| /*! |
| * @brief Channel status flags. |
| */ |
| enum _adc16_channel_status_flags |
| { |
| kADC16_ChannelConversionDoneFlag = ADC_SC1_COCO_MASK, /*!< Conversion done. */ |
| }; |
| |
| /*! |
| * @brief Converter status flags. |
| */ |
| enum _adc16_status_flags |
| { |
| kADC16_ActiveFlag = ADC_SC2_ADACT_MASK, /*!< Converter is active. */ |
| #if defined(FSL_FEATURE_ADC16_HAS_CALIBRATION) && FSL_FEATURE_ADC16_HAS_CALIBRATION |
| kADC16_CalibrationFailedFlag = ADC_SC3_CALF_MASK, /*!< Calibration is failed. */ |
| #endif /* FSL_FEATURE_ADC16_HAS_CALIBRATION */ |
| }; |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_MUX_SELECT) && FSL_FEATURE_ADC16_HAS_MUX_SELECT |
| /*! |
| * @brief Channel multiplexer mode for each channel. |
| * |
| * For some ADC16 channels, there are two pin selections in channel multiplexer. For example, ADC0_SE4a and ADC0_SE4b |
| * are the different channels that share the same channel number. |
| */ |
| typedef enum _adc_channel_mux_mode |
| { |
| kADC16_ChannelMuxA = 0U, /*!< For channel with channel mux a. */ |
| kADC16_ChannelMuxB = 1U, /*!< For channel with channel mux b. */ |
| } adc16_channel_mux_mode_t; |
| #endif /* FSL_FEATURE_ADC16_HAS_MUX_SELECT */ |
| |
| /*! |
| * @brief Clock divider for the converter. |
| */ |
| typedef enum _adc16_clock_divider |
| { |
| kADC16_ClockDivider1 = 0U, /*!< For divider 1 from the input clock to the module. */ |
| kADC16_ClockDivider2 = 1U, /*!< For divider 2 from the input clock to the module. */ |
| kADC16_ClockDivider4 = 2U, /*!< For divider 4 from the input clock to the module. */ |
| kADC16_ClockDivider8 = 3U, /*!< For divider 8 from the input clock to the module. */ |
| } adc16_clock_divider_t; |
| |
| /*! |
| *@brief Converter's resolution. |
| */ |
| typedef enum _adc16_resolution |
| { |
| /* This group of enumeration is for internal use which is related to register setting. */ |
| kADC16_Resolution8or9Bit = 0U, /*!< Single End 8-bit or Differential Sample 9-bit. */ |
| kADC16_Resolution12or13Bit = 1U, /*!< Single End 12-bit or Differential Sample 13-bit. */ |
| kADC16_Resolution10or11Bit = 2U, /*!< Single End 10-bit or Differential Sample 11-bit. */ |
| |
| /* This group of enumeration is for a public user. */ |
| kADC16_ResolutionSE8Bit = kADC16_Resolution8or9Bit, /*!< Single End 8-bit. */ |
| kADC16_ResolutionSE12Bit = kADC16_Resolution12or13Bit, /*!< Single End 12-bit. */ |
| kADC16_ResolutionSE10Bit = kADC16_Resolution10or11Bit, /*!< Single End 10-bit. */ |
| #if defined(FSL_FEATURE_ADC16_HAS_DIFF_MODE) && FSL_FEATURE_ADC16_HAS_DIFF_MODE |
| kADC16_ResolutionDF9Bit = kADC16_Resolution8or9Bit, /*!< Differential Sample 9-bit. */ |
| kADC16_ResolutionDF13Bit = kADC16_Resolution12or13Bit, /*!< Differential Sample 13-bit. */ |
| kADC16_ResolutionDF11Bit = kADC16_Resolution10or11Bit, /*!< Differential Sample 11-bit. */ |
| #endif /* FSL_FEATURE_ADC16_HAS_DIFF_MODE */ |
| |
| #if defined(FSL_FEATURE_ADC16_MAX_RESOLUTION) && (FSL_FEATURE_ADC16_MAX_RESOLUTION >= 16U) |
| /* 16-bit is supported by default. */ |
| kADC16_Resolution16Bit = 3U, /*!< Single End 16-bit or Differential Sample 16-bit. */ |
| kADC16_ResolutionSE16Bit = kADC16_Resolution16Bit, /*!< Single End 16-bit. */ |
| #if defined(FSL_FEATURE_ADC16_HAS_DIFF_MODE) && FSL_FEATURE_ADC16_HAS_DIFF_MODE |
| kADC16_ResolutionDF16Bit = kADC16_Resolution16Bit, /*!< Differential Sample 16-bit. */ |
| #endif /* FSL_FEATURE_ADC16_HAS_DIFF_MODE */ |
| #endif /* FSL_FEATURE_ADC16_MAX_RESOLUTION >= 16U */ |
| } adc16_resolution_t; |
| |
| /*! |
| * @brief Clock source. |
| */ |
| typedef enum _adc16_clock_source |
| { |
| kADC16_ClockSourceAlt0 = 0U, /*!< Selection 0 of the clock source. */ |
| kADC16_ClockSourceAlt1 = 1U, /*!< Selection 1 of the clock source. */ |
| kADC16_ClockSourceAlt2 = 2U, /*!< Selection 2 of the clock source. */ |
| kADC16_ClockSourceAlt3 = 3U, /*!< Selection 3 of the clock source. */ |
| |
| /* Chip defined clock source */ |
| kADC16_ClockSourceAsynchronousClock = kADC16_ClockSourceAlt3, /*!< Using internal asynchronous clock. */ |
| } adc16_clock_source_t; |
| |
| /*! |
| * @brief Long sample mode. |
| */ |
| typedef enum _adc16_long_sample_mode |
| { |
| kADC16_LongSampleCycle24 = 0U, /*!< 20 extra ADCK cycles, 24 ADCK cycles total. */ |
| kADC16_LongSampleCycle16 = 1U, /*!< 12 extra ADCK cycles, 16 ADCK cycles total. */ |
| kADC16_LongSampleCycle10 = 2U, /*!< 6 extra ADCK cycles, 10 ADCK cycles total. */ |
| kADC16_LongSampleCycle6 = 3U, /*!< 2 extra ADCK cycles, 6 ADCK cycles total. */ |
| kADC16_LongSampleDisabled = 4U, /*!< Disable the long sample feature. */ |
| } adc16_long_sample_mode_t; |
| |
| /*! |
| * @brief Reference voltage source. |
| */ |
| typedef enum _adc16_reference_voltage_source |
| { |
| kADC16_ReferenceVoltageSourceVref = 0U, /*!< For external pins pair of VrefH and VrefL. */ |
| kADC16_ReferenceVoltageSourceValt = 1U, /*!< For alternate reference pair of ValtH and ValtL. */ |
| } adc16_reference_voltage_source_t; |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_HW_AVERAGE) && FSL_FEATURE_ADC16_HAS_HW_AVERAGE |
| /*! |
| * @brief Hardware average mode. |
| */ |
| typedef enum _adc16_hardware_average_mode |
| { |
| kADC16_HardwareAverageCount4 = 0U, /*!< For hardware average with 4 samples. */ |
| kADC16_HardwareAverageCount8 = 1U, /*!< For hardware average with 8 samples. */ |
| kADC16_HardwareAverageCount16 = 2U, /*!< For hardware average with 16 samples. */ |
| kADC16_HardwareAverageCount32 = 3U, /*!< For hardware average with 32 samples. */ |
| kADC16_HardwareAverageDisabled = 4U, /*!< Disable the hardware average feature.*/ |
| } adc16_hardware_average_mode_t; |
| #endif /* FSL_FEATURE_ADC16_HAS_HW_AVERAGE */ |
| |
| /*! |
| * @brief Hardware compare mode. |
| */ |
| typedef enum _adc16_hardware_compare_mode |
| { |
| kADC16_HardwareCompareMode0 = 0U, /*!< x < value1. */ |
| kADC16_HardwareCompareMode1 = 1U, /*!< x > value1. */ |
| kADC16_HardwareCompareMode2 = 2U, /*!< if value1 <= value2, then x < value1 || x > value2; |
| else, value1 > x > value2. */ |
| kADC16_HardwareCompareMode3 = 3U, /*!< if value1 <= value2, then value1 <= x <= value2; |
| else x >= value1 || x <= value2. */ |
| } adc16_hardware_compare_mode_t; |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_PGA) && FSL_FEATURE_ADC16_HAS_PGA |
| /*! |
| * @brief PGA's Gain mode. |
| */ |
| typedef enum _adc16_pga_gain |
| { |
| kADC16_PGAGainValueOf1 = 0U, /*!< For amplifier gain of 1. */ |
| kADC16_PGAGainValueOf2 = 1U, /*!< For amplifier gain of 2. */ |
| kADC16_PGAGainValueOf4 = 2U, /*!< For amplifier gain of 4. */ |
| kADC16_PGAGainValueOf8 = 3U, /*!< For amplifier gain of 8. */ |
| kADC16_PGAGainValueOf16 = 4U, /*!< For amplifier gain of 16. */ |
| kADC16_PGAGainValueOf32 = 5U, /*!< For amplifier gain of 32. */ |
| kADC16_PGAGainValueOf64 = 6U, /*!< For amplifier gain of 64. */ |
| } adc16_pga_gain_t; |
| #endif /* FSL_FEATURE_ADC16_HAS_PGA */ |
| |
| /*! |
| * @brief ADC16 converter configuration. |
| */ |
| typedef struct _adc16_config |
| { |
| adc16_reference_voltage_source_t referenceVoltageSource; /*!< Select the reference voltage source. */ |
| adc16_clock_source_t clockSource; /*!< Select the input clock source to converter. */ |
| bool enableAsynchronousClock; /*!< Enable the asynchronous clock output. */ |
| adc16_clock_divider_t clockDivider; /*!< Select the divider of input clock source. */ |
| adc16_resolution_t resolution; /*!< Select the sample resolution mode. */ |
| adc16_long_sample_mode_t longSampleMode; /*!< Select the long sample mode. */ |
| bool enableHighSpeed; /*!< Enable the high-speed mode. */ |
| bool enableLowPower; /*!< Enable low power. */ |
| bool enableContinuousConversion; /*!< Enable continuous conversion mode. */ |
| } adc16_config_t; |
| |
| /*! |
| * @brief ADC16 Hardware comparison configuration. |
| */ |
| typedef struct _adc16_hardware_compare_config |
| { |
| adc16_hardware_compare_mode_t hardwareCompareMode; /*!< Select the hardware compare mode. |
| See "adc16_hardware_compare_mode_t". */ |
| int16_t value1; /*!< Setting value1 for hardware compare mode. */ |
| int16_t value2; /*!< Setting value2 for hardware compare mode. */ |
| } adc16_hardware_compare_config_t; |
| |
| /*! |
| * @brief ADC16 channel conversion configuration. |
| */ |
| typedef struct _adc16_channel_config |
| { |
| uint32_t channelNumber; /*!< Setting the conversion channel number. The available range is 0-31. |
| See channel connection information for each chip in Reference |
| Manual document. */ |
| bool enableInterruptOnConversionCompleted; /*!< Generate an interrupt request once the conversion is completed. */ |
| #if defined(FSL_FEATURE_ADC16_HAS_DIFF_MODE) && FSL_FEATURE_ADC16_HAS_DIFF_MODE |
| bool enableDifferentialConversion; /*!< Using Differential sample mode. */ |
| #endif /* FSL_FEATURE_ADC16_HAS_DIFF_MODE */ |
| } adc16_channel_config_t; |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_PGA) && FSL_FEATURE_ADC16_HAS_PGA |
| /*! |
| * @brief ADC16 programmable gain amplifier configuration. |
| */ |
| typedef struct _adc16_pga_config |
| { |
| adc16_pga_gain_t pgaGain; /*!< Setting PGA gain. */ |
| bool enableRunInNormalMode; /*!< Enable PGA working in normal mode, or low power mode by default. */ |
| #if defined(FSL_FEATURE_ADC16_HAS_PGA_CHOPPING) && FSL_FEATURE_ADC16_HAS_PGA_CHOPPING |
| bool disablePgaChopping; /*!< Disable the PGA chopping function. |
| The PGA employs chopping to remove/reduce offset and 1/f noise and offers |
| an offset measurement configuration that aids the offset calibration. */ |
| #endif /* FSL_FEATURE_ADC16_HAS_PGA_CHOPPING */ |
| #if defined(FSL_FEATURE_ADC16_HAS_PGA_OFFSET_MEASUREMENT) && FSL_FEATURE_ADC16_HAS_PGA_OFFSET_MEASUREMENT |
| bool enableRunInOffsetMeasurement; /*!< Enable the PGA working in offset measurement mode. |
| When this feature is enabled, the PGA disconnects itself from the external |
| inputs and auto-configures into offset measurement mode. With this field |
| set, run the ADC in the recommended settings and enable the maximum hardware |
| averaging to get the PGA offset number. The output is the |
| (PGA offset * (64+1)) for the given PGA setting. */ |
| #endif /* FSL_FEATURE_ADC16_HAS_PGA_OFFSET_MEASUREMENT */ |
| } adc16_pga_config_t; |
| #endif /* FSL_FEATURE_ADC16_HAS_PGA */ |
| |
| #if defined(__cplusplus) |
| extern "C" { |
| #endif |
| |
| /******************************************************************************* |
| * API |
| ******************************************************************************/ |
| |
| /*! |
| * @name Initialization |
| * @{ |
| */ |
| |
| /*! |
| * @brief Initializes the ADC16 module. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param config Pointer to configuration structure. See "adc16_config_t". |
| */ |
| void ADC16_Init(ADC_Type *base, const adc16_config_t *config); |
| |
| /*! |
| * @brief De-initializes the ADC16 module. |
| * |
| * @param base ADC16 peripheral base address. |
| */ |
| void ADC16_Deinit(ADC_Type *base); |
| |
| /*! |
| * @brief Gets an available pre-defined settings for the converter's configuration. |
| * |
| * This function initializes the converter configuration structure with available settings. The default values are as follows. |
| * @code |
| * config->referenceVoltageSource = kADC16_ReferenceVoltageSourceVref; |
| * config->clockSource = kADC16_ClockSourceAsynchronousClock; |
| * config->enableAsynchronousClock = true; |
| * config->clockDivider = kADC16_ClockDivider8; |
| * config->resolution = kADC16_ResolutionSE12Bit; |
| * config->longSampleMode = kADC16_LongSampleDisabled; |
| * config->enableHighSpeed = false; |
| * config->enableLowPower = false; |
| * config->enableContinuousConversion = false; |
| * @endcode |
| * @param config Pointer to the configuration structure. |
| */ |
| void ADC16_GetDefaultConfig(adc16_config_t *config); |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_CALIBRATION) && FSL_FEATURE_ADC16_HAS_CALIBRATION |
| /*! |
| * @brief Automates the hardware calibration. |
| * |
| * This auto calibration helps to adjust the plus/minus side gain automatically. |
| * Execute the calibration before using the converter. Note that the hardware trigger should be used |
| * during the calibration. |
| * |
| * @param base ADC16 peripheral base address. |
| * |
| * @return Execution status. |
| * @retval kStatus_Success Calibration is done successfully. |
| * @retval kStatus_Fail Calibration has failed. |
| */ |
| status_t ADC16_DoAutoCalibration(ADC_Type *base); |
| #endif /* FSL_FEATURE_ADC16_HAS_CALIBRATION */ |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_OFFSET_CORRECTION) && FSL_FEATURE_ADC16_HAS_OFFSET_CORRECTION |
| /*! |
| * @brief Sets the offset value for the conversion result. |
| * |
| * This offset value takes effect on the conversion result. If the offset value is not zero, the reading result |
| * is subtracted by it. Note, the hardware calibration fills the offset value automatically. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param value Setting offset value. |
| */ |
| static inline void ADC16_SetOffsetValue(ADC_Type *base, int16_t value) |
| { |
| base->OFS = (uint32_t)(value); |
| } |
| #endif /* FSL_FEATURE_ADC16_HAS_OFFSET_CORRECTION */ |
| |
| /* @} */ |
| |
| /*! |
| * @name Advanced Features |
| * @{ |
| */ |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_DMA) && FSL_FEATURE_ADC16_HAS_DMA |
| /*! |
| * @brief Enables generating the DMA trigger when the conversion is complete. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param enable Switcher of the DMA feature. "true" means enabled, "false" means not enabled. |
| */ |
| static inline void ADC16_EnableDMA(ADC_Type *base, bool enable) |
| { |
| if (enable) |
| { |
| base->SC2 |= ADC_SC2_DMAEN_MASK; |
| } |
| else |
| { |
| base->SC2 &= ~ADC_SC2_DMAEN_MASK; |
| } |
| } |
| #endif /* FSL_FEATURE_ADC16_HAS_DMA */ |
| |
| /*! |
| * @brief Enables the hardware trigger mode. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param enable Switcher of the hardware trigger feature. "true" means enabled, "false" means not enabled. |
| */ |
| static inline void ADC16_EnableHardwareTrigger(ADC_Type *base, bool enable) |
| { |
| if (enable) |
| { |
| base->SC2 |= ADC_SC2_ADTRG_MASK; |
| } |
| else |
| { |
| base->SC2 &= ~ADC_SC2_ADTRG_MASK; |
| } |
| } |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_MUX_SELECT) && FSL_FEATURE_ADC16_HAS_MUX_SELECT |
| /*! |
| * @brief Sets the channel mux mode. |
| * |
| * Some sample pins share the same channel index. The channel mux mode decides which pin is used for an |
| * indicated channel. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param mode Setting channel mux mode. See "adc16_channel_mux_mode_t". |
| */ |
| void ADC16_SetChannelMuxMode(ADC_Type *base, adc16_channel_mux_mode_t mode); |
| #endif /* FSL_FEATURE_ADC16_HAS_MUX_SELECT */ |
| |
| /*! |
| * @brief Configures the hardware compare mode. |
| * |
| * The hardware compare mode provides a way to process the conversion result automatically by using hardware. Only the result |
| * in the compare range is available. To compare the range, see "adc16_hardware_compare_mode_t" or the appopriate reference |
| * manual for more information. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param config Pointer to the "adc16_hardware_compare_config_t" structure. Passing "NULL" disables the feature. |
| */ |
| void ADC16_SetHardwareCompareConfig(ADC_Type *base, const adc16_hardware_compare_config_t *config); |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_HW_AVERAGE) && FSL_FEATURE_ADC16_HAS_HW_AVERAGE |
| /*! |
| * @brief Sets the hardware average mode. |
| * |
| * The hardware average mode provides a way to process the conversion result automatically by using hardware. The multiple |
| * conversion results are accumulated and averaged internally making them easier to read. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param mode Setting the hardware average mode. See "adc16_hardware_average_mode_t". |
| */ |
| void ADC16_SetHardwareAverage(ADC_Type *base, adc16_hardware_average_mode_t mode); |
| #endif /* FSL_FEATURE_ADC16_HAS_HW_AVERAGE */ |
| |
| #if defined(FSL_FEATURE_ADC16_HAS_PGA) && FSL_FEATURE_ADC16_HAS_PGA |
| /*! |
| * @brief Configures the PGA for the converter's front end. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param config Pointer to the "adc16_pga_config_t" structure. Passing "NULL" disables the feature. |
| */ |
| void ADC16_SetPGAConfig(ADC_Type *base, const adc16_pga_config_t *config); |
| #endif /* FSL_FEATURE_ADC16_HAS_PGA */ |
| |
| /*! |
| * @brief Gets the status flags of the converter. |
| * |
| * @param base ADC16 peripheral base address. |
| * |
| * @return Flags' mask if indicated flags are asserted. See "_adc16_status_flags". |
| */ |
| uint32_t ADC16_GetStatusFlags(ADC_Type *base); |
| |
| /*! |
| * @brief Clears the status flags of the converter. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param mask Mask value for the cleared flags. See "_adc16_status_flags". |
| */ |
| void ADC16_ClearStatusFlags(ADC_Type *base, uint32_t mask); |
| |
| /* @} */ |
| |
| /*! |
| * @name Conversion Channel |
| * @{ |
| */ |
| |
| /*! |
| * @brief Configures the conversion channel. |
| * |
| * This operation triggers the conversion when in software trigger mode. When in hardware trigger mode, this API |
| * configures the channel while the external trigger source helps to trigger the conversion. |
| * |
| * Note that the "Channel Group" has a detailed description. |
| * To allow sequential conversions of the ADC to be triggered by internal peripherals, the ADC has more than one |
| * group of status and control registers, one for each conversion. The channel group parameter indicates which group of |
| * registers are used, for example, channel group 0 is for Group A registers and channel group 1 is for Group B registers. The |
| * channel groups are used in a "ping-pong" approach to control the ADC operation. At any point, only one of |
| * the channel groups is actively controlling ADC conversions. The channel group 0 is used for both software and hardware |
| * trigger modes. Channel group 1 and greater indicates multiple channel group registers for |
| * use only in hardware trigger mode. See the chip configuration information in the appropriate MCU reference manual for the |
| * number of SC1n registers (channel groups) specific to this device. Channel group 1 or greater are not used |
| * for software trigger operation. Therefore, writing to these channel groups does not initiate a new conversion. |
| * Updating the channel group 0 while a different channel group is actively controlling a conversion is allowed and |
| * vice versa. Writing any of the channel group registers while that specific channel group is actively controlling a |
| * conversion aborts the current conversion. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param channelGroup Channel group index. |
| * @param config Pointer to the "adc16_channel_config_t" structure for the conversion channel. |
| */ |
| void ADC16_SetChannelConfig(ADC_Type *base, uint32_t channelGroup, const adc16_channel_config_t *config); |
| |
| /*! |
| * @brief Gets the conversion value. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param channelGroup Channel group index. |
| * |
| * @return Conversion value. |
| */ |
| static inline uint32_t ADC16_GetChannelConversionValue(ADC_Type *base, uint32_t channelGroup) |
| { |
| assert(channelGroup < ADC_R_COUNT); |
| |
| return base->R[channelGroup]; |
| } |
| |
| /*! |
| * @brief Gets the status flags of channel. |
| * |
| * @param base ADC16 peripheral base address. |
| * @param channelGroup Channel group index. |
| * |
| * @return Flags' mask if indicated flags are asserted. See "_adc16_channel_status_flags". |
| */ |
| uint32_t ADC16_GetChannelStatusFlags(ADC_Type *base, uint32_t channelGroup); |
| |
| /* @} */ |
| |
| #if defined(__cplusplus) |
| } |
| #endif |
| /*! |
| * @} |
| */ |
| #endif /* _FSL_ADC16_H_ */ |