/** | |
****************************************************************************** | |
* @file stm32f4xx_hal_pwr.c | |
* @author MCD Application Team | |
* @version V1.7.0 | |
* @date 17-February-2017 | |
* @brief PWR HAL module driver. | |
* This file provides firmware functions to manage the following | |
* functionalities of the Power Controller (PWR) peripheral: | |
* + Initialization and de-initialization functions | |
* + Peripheral Control functions | |
* | |
****************************************************************************** | |
* @attention | |
* | |
* <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> | |
* | |
* Redistribution and use in source and binary forms, with or without modification, | |
* are permitted provided that the following conditions are met: | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* 3. Neither the name of STMicroelectronics nor the names of its contributors | |
* may be used to endorse or promote products derived from this software | |
* without specific prior written permission. | |
* | |
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" | |
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE | |
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE | |
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE | |
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, | |
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE | |
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. | |
* | |
****************************************************************************** | |
*/ | |
/* Includes ------------------------------------------------------------------*/ | |
#include "stm32f4xx_hal.h" | |
/** @addtogroup STM32F4xx_HAL_Driver | |
* @{ | |
*/ | |
/** @defgroup PWR PWR | |
* @brief PWR HAL module driver | |
* @{ | |
*/ | |
#ifdef HAL_PWR_MODULE_ENABLED | |
/* Private typedef -----------------------------------------------------------*/ | |
/* Private define ------------------------------------------------------------*/ | |
/** @addtogroup PWR_Private_Constants | |
* @{ | |
*/ | |
/** @defgroup PWR_PVD_Mode_Mask PWR PVD Mode Mask | |
* @{ | |
*/ | |
#define PVD_MODE_IT 0x00010000U | |
#define PVD_MODE_EVT 0x00020000U | |
#define PVD_RISING_EDGE 0x00000001U | |
#define PVD_FALLING_EDGE 0x00000002U | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/* Private macro -------------------------------------------------------------*/ | |
/* Private variables ---------------------------------------------------------*/ | |
/* Private function prototypes -----------------------------------------------*/ | |
/* Private functions ---------------------------------------------------------*/ | |
/** @defgroup PWR_Exported_Functions PWR Exported Functions | |
* @{ | |
*/ | |
/** @defgroup PWR_Exported_Functions_Group1 Initialization and de-initialization functions | |
* @brief Initialization and de-initialization functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Initialization and de-initialization functions ##### | |
=============================================================================== | |
[..] | |
After reset, the backup domain (RTC registers, RTC backup data | |
registers and backup SRAM) is protected against possible unwanted | |
write accesses. | |
To enable access to the RTC Domain and RTC registers, proceed as follows: | |
(+) Enable the Power Controller (PWR) APB1 interface clock using the | |
__HAL_RCC_PWR_CLK_ENABLE() macro. | |
(+) Enable access to RTC domain using the HAL_PWR_EnableBkUpAccess() function. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Deinitializes the HAL PWR peripheral registers to their default reset values. | |
* @retval None | |
*/ | |
void HAL_PWR_DeInit(void) | |
{ | |
__HAL_RCC_PWR_FORCE_RESET(); | |
__HAL_RCC_PWR_RELEASE_RESET(); | |
} | |
/** | |
* @brief Enables access to the backup domain (RTC registers, RTC | |
* backup data registers and backup SRAM). | |
* @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the | |
* Backup Domain Access should be kept enabled. | |
* @retval None | |
*/ | |
void HAL_PWR_EnableBkUpAccess(void) | |
{ | |
*(__IO uint32_t *) CR_DBP_BB = (uint32_t)ENABLE; | |
} | |
/** | |
* @brief Disables access to the backup domain (RTC registers, RTC | |
* backup data registers and backup SRAM). | |
* @note If the HSE divided by 2, 3, ..31 is used as the RTC clock, the | |
* Backup Domain Access should be kept enabled. | |
* @retval None | |
*/ | |
void HAL_PWR_DisableBkUpAccess(void) | |
{ | |
*(__IO uint32_t *) CR_DBP_BB = (uint32_t)DISABLE; | |
} | |
/** | |
* @} | |
*/ | |
/** @defgroup PWR_Exported_Functions_Group2 Peripheral Control functions | |
* @brief Low Power modes configuration functions | |
* | |
@verbatim | |
=============================================================================== | |
##### Peripheral Control functions ##### | |
=============================================================================== | |
*** PVD configuration *** | |
========================= | |
[..] | |
(+) The PVD is used to monitor the VDD power supply by comparing it to a | |
threshold selected by the PVD Level (PLS[2:0] bits in the PWR_CR). | |
(+) A PVDO flag is available to indicate if VDD/VDDA is higher or lower | |
than the PVD threshold. This event is internally connected to the EXTI | |
line16 and can generate an interrupt if enabled. This is done through | |
__HAL_PWR_PVD_EXTI_ENABLE_IT() macro. | |
(+) The PVD is stopped in Standby mode. | |
*** Wake-up pin configuration *** | |
================================ | |
[..] | |
(+) Wake-up pin is used to wake up the system from Standby mode. This pin is | |
forced in input pull-down configuration and is active on rising edges. | |
(+) There is one Wake-up pin: Wake-up Pin 1 on PA.00. | |
(++) For STM32F446xx there are two Wake-Up pins: Pin1 on PA.00 and Pin2 on PC.13 | |
(++) For STM32F410xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx there are three Wake-Up pins: Pin1 on PA.00, Pin2 on PC.00 and Pin3 on PC.01 | |
*** Low Power modes configuration *** | |
===================================== | |
[..] | |
The devices feature 3 low-power modes: | |
(+) Sleep mode: Cortex-M4 core stopped, peripherals kept running. | |
(+) Stop mode: all clocks are stopped, regulator running, regulator | |
in low power mode | |
(+) Standby mode: 1.2V domain powered off. | |
*** Sleep mode *** | |
================== | |
[..] | |
(+) Entry: | |
The Sleep mode is entered by using the HAL_PWR_EnterSLEEPMode(PWR_MAINREGULATOR_ON, PWR_SLEEPENTRY_WFI) | |
functions with | |
(++) PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction | |
(++) PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction | |
-@@- The Regulator parameter is not used for the STM32F4 family | |
and is kept as parameter just to maintain compatibility with the | |
lower power families (STM32L). | |
(+) Exit: | |
Any peripheral interrupt acknowledged by the nested vectored interrupt | |
controller (NVIC) can wake up the device from Sleep mode. | |
*** Stop mode *** | |
================= | |
[..] | |
In Stop mode, all clocks in the 1.2V domain are stopped, the PLL, the HSI, | |
and the HSE RC oscillators are disabled. Internal SRAM and register contents | |
are preserved. | |
The voltage regulator can be configured either in normal or low-power mode. | |
To minimize the consumption In Stop mode, FLASH can be powered off before | |
entering the Stop mode using the HAL_PWREx_EnableFlashPowerDown() function. | |
It can be switched on again by software after exiting the Stop mode using | |
the HAL_PWREx_DisableFlashPowerDown() function. | |
(+) Entry: | |
The Stop mode is entered using the HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON) | |
function with: | |
(++) Main regulator ON. | |
(++) Low Power regulator ON. | |
(+) Exit: | |
Any EXTI Line (Internal or External) configured in Interrupt/Event mode. | |
*** Standby mode *** | |
==================== | |
[..] | |
(+) | |
The Standby mode allows to achieve the lowest power consumption. It is based | |
on the Cortex-M4 deep sleep mode, with the voltage regulator disabled. | |
The 1.2V domain is consequently powered off. The PLL, the HSI oscillator and | |
the HSE oscillator are also switched off. SRAM and register contents are lost | |
except for the RTC registers, RTC backup registers, backup SRAM and Standby | |
circuitry. | |
The voltage regulator is OFF. | |
(++) Entry: | |
(+++) The Standby mode is entered using the HAL_PWR_EnterSTANDBYMode() function. | |
(++) Exit: | |
(+++) WKUP pin rising edge, RTC alarm (Alarm A and Alarm B), RTC wake-up, | |
tamper event, time-stamp event, external reset in NRST pin, IWDG reset. | |
*** Auto-wake-up (AWU) from low-power mode *** | |
============================================= | |
[..] | |
(+) The MCU can be woken up from low-power mode by an RTC Alarm event, an RTC | |
Wake-up event, a tamper event or a time-stamp event, without depending on | |
an external interrupt (Auto-wake-up mode). | |
(+) RTC auto-wake-up (AWU) from the Stop and Standby modes | |
(++) To wake up from the Stop mode with an RTC alarm event, it is necessary to | |
configure the RTC to generate the RTC alarm using the HAL_RTC_SetAlarm_IT() function. | |
(++) To wake up from the Stop mode with an RTC Tamper or time stamp event, it | |
is necessary to configure the RTC to detect the tamper or time stamp event using the | |
HAL_RTCEx_SetTimeStamp_IT() or HAL_RTCEx_SetTamper_IT() functions. | |
(++) To wake up from the Stop mode with an RTC Wake-up event, it is necessary to | |
configure the RTC to generate the RTC Wake-up event using the HAL_RTCEx_SetWakeUpTimer_IT() function. | |
@endverbatim | |
* @{ | |
*/ | |
/** | |
* @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD). | |
* @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration | |
* information for the PVD. | |
* @note Refer to the electrical characteristics of your device datasheet for | |
* more details about the voltage threshold corresponding to each | |
* detection level. | |
* @retval None | |
*/ | |
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel)); | |
assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode)); | |
/* Set PLS[7:5] bits according to PVDLevel value */ | |
MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel); | |
/* Clear any previous config. Keep it clear if no event or IT mode is selected */ | |
__HAL_PWR_PVD_EXTI_DISABLE_EVENT(); | |
__HAL_PWR_PVD_EXTI_DISABLE_IT(); | |
__HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE(); | |
__HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); | |
/* Configure interrupt mode */ | |
if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT) | |
{ | |
__HAL_PWR_PVD_EXTI_ENABLE_IT(); | |
} | |
/* Configure event mode */ | |
if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT) | |
{ | |
__HAL_PWR_PVD_EXTI_ENABLE_EVENT(); | |
} | |
/* Configure the edge */ | |
if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE) | |
{ | |
__HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE(); | |
} | |
if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE) | |
{ | |
__HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE(); | |
} | |
} | |
/** | |
* @brief Enables the Power Voltage Detector(PVD). | |
* @retval None | |
*/ | |
void HAL_PWR_EnablePVD(void) | |
{ | |
*(__IO uint32_t *) CR_PVDE_BB = (uint32_t)ENABLE; | |
} | |
/** | |
* @brief Disables the Power Voltage Detector(PVD). | |
* @retval None | |
*/ | |
void HAL_PWR_DisablePVD(void) | |
{ | |
*(__IO uint32_t *) CR_PVDE_BB = (uint32_t)DISABLE; | |
} | |
/** | |
* @brief Enables the Wake-up PINx functionality. | |
* @param WakeUpPinx: Specifies the Power Wake-Up pin to enable. | |
* This parameter can be one of the following values: | |
* @arg PWR_WAKEUP_PIN1 | |
* @arg PWR_WAKEUP_PIN2 available only on STM32F410xx/STM32F446xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices | |
* @arg PWR_WAKEUP_PIN3 available only on STM32F410xx/STM32F412xx devices | |
* @retval None | |
*/ | |
void HAL_PWR_EnableWakeUpPin(uint32_t WakeUpPinx) | |
{ | |
/* Check the parameter */ | |
assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); | |
/* Enable the wake up pin */ | |
SET_BIT(PWR->CSR, WakeUpPinx); | |
} | |
/** | |
* @brief Disables the Wake-up PINx functionality. | |
* @param WakeUpPinx: Specifies the Power Wake-Up pin to disable. | |
* This parameter can be one of the following values: | |
* @arg PWR_WAKEUP_PIN1 | |
* @arg PWR_WAKEUP_PIN2 available only on STM32F410xx/STM32F446xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices | |
* @arg PWR_WAKEUP_PIN3 available only on STM32F410xx/STM32F412Zx/STM32F412Rx/STM32F412Vx/STM32F412Cx devices | |
* @retval None | |
*/ | |
void HAL_PWR_DisableWakeUpPin(uint32_t WakeUpPinx) | |
{ | |
/* Check the parameter */ | |
assert_param(IS_PWR_WAKEUP_PIN(WakeUpPinx)); | |
/* Disable the wake up pin */ | |
CLEAR_BIT(PWR->CSR, WakeUpPinx); | |
} | |
/** | |
* @brief Enters Sleep mode. | |
* | |
* @note In Sleep mode, all I/O pins keep the same state as in Run mode. | |
* | |
* @note In Sleep mode, the systick is stopped to avoid exit from this mode with | |
* systick interrupt when used as time base for Timeout | |
* | |
* @param Regulator: Specifies the regulator state in SLEEP mode. | |
* This parameter can be one of the following values: | |
* @arg PWR_MAINREGULATOR_ON: SLEEP mode with regulator ON | |
* @arg PWR_LOWPOWERREGULATOR_ON: SLEEP mode with low power regulator ON | |
* @note This parameter is not used for the STM32F4 family and is kept as parameter | |
* just to maintain compatibility with the lower power families. | |
* @param SLEEPEntry: Specifies if SLEEP mode in entered with WFI or WFE instruction. | |
* This parameter can be one of the following values: | |
* @arg PWR_SLEEPENTRY_WFI: enter SLEEP mode with WFI instruction | |
* @arg PWR_SLEEPENTRY_WFE: enter SLEEP mode with WFE instruction | |
* @retval None | |
*/ | |
void HAL_PWR_EnterSLEEPMode(uint32_t Regulator, uint8_t SLEEPEntry) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_PWR_REGULATOR(Regulator)); | |
assert_param(IS_PWR_SLEEP_ENTRY(SLEEPEntry)); | |
/* Clear SLEEPDEEP bit of Cortex System Control Register */ | |
CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); | |
/* Select SLEEP mode entry -------------------------------------------------*/ | |
if(SLEEPEntry == PWR_SLEEPENTRY_WFI) | |
{ | |
/* Request Wait For Interrupt */ | |
__WFI(); | |
} | |
else | |
{ | |
/* Request Wait For Event */ | |
__SEV(); | |
__WFE(); | |
__WFE(); | |
} | |
} | |
/** | |
* @brief Enters Stop mode. | |
* @note In Stop mode, all I/O pins keep the same state as in Run mode. | |
* @note When exiting Stop mode by issuing an interrupt or a wake-up event, | |
* the HSI RC oscillator is selected as system clock. | |
* @note When the voltage regulator operates in low power mode, an additional | |
* startup delay is incurred when waking up from Stop mode. | |
* By keeping the internal regulator ON during Stop mode, the consumption | |
* is higher although the startup time is reduced. | |
* @param Regulator: Specifies the regulator state in Stop mode. | |
* This parameter can be one of the following values: | |
* @arg PWR_MAINREGULATOR_ON: Stop mode with regulator ON | |
* @arg PWR_LOWPOWERREGULATOR_ON: Stop mode with low power regulator ON | |
* @param STOPEntry: Specifies if Stop mode in entered with WFI or WFE instruction. | |
* This parameter can be one of the following values: | |
* @arg PWR_STOPENTRY_WFI: Enter Stop mode with WFI instruction | |
* @arg PWR_STOPENTRY_WFE: Enter Stop mode with WFE instruction | |
* @retval None | |
*/ | |
void HAL_PWR_EnterSTOPMode(uint32_t Regulator, uint8_t STOPEntry) | |
{ | |
/* Check the parameters */ | |
assert_param(IS_PWR_REGULATOR(Regulator)); | |
assert_param(IS_PWR_STOP_ENTRY(STOPEntry)); | |
/* Select the regulator state in Stop mode: Set PDDS and LPDS bits according to PWR_Regulator value */ | |
MODIFY_REG(PWR->CR, (PWR_CR_PDDS | PWR_CR_LPDS), Regulator); | |
/* Set SLEEPDEEP bit of Cortex System Control Register */ | |
SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); | |
/* Select Stop mode entry --------------------------------------------------*/ | |
if(STOPEntry == PWR_STOPENTRY_WFI) | |
{ | |
/* Request Wait For Interrupt */ | |
__WFI(); | |
} | |
else | |
{ | |
/* Request Wait For Event */ | |
__SEV(); | |
__WFE(); | |
__WFE(); | |
} | |
/* Reset SLEEPDEEP bit of Cortex System Control Register */ | |
CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); | |
} | |
/** | |
* @brief Enters Standby mode. | |
* @note In Standby mode, all I/O pins are high impedance except for: | |
* - Reset pad (still available) | |
* - RTC_AF1 pin (PC13) if configured for tamper, time-stamp, RTC | |
* Alarm out, or RTC clock calibration out. | |
* - RTC_AF2 pin (PI8) if configured for tamper or time-stamp. | |
* - WKUP pin 1 (PA0) if enabled. | |
* @retval None | |
*/ | |
void HAL_PWR_EnterSTANDBYMode(void) | |
{ | |
/* Select Standby mode */ | |
SET_BIT(PWR->CR, PWR_CR_PDDS); | |
/* Set SLEEPDEEP bit of Cortex System Control Register */ | |
SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPDEEP_Msk)); | |
/* This option is used to ensure that store operations are completed */ | |
#if defined ( __CC_ARM) | |
__force_stores(); | |
#endif | |
/* Request Wait For Interrupt */ | |
__WFI(); | |
} | |
/** | |
* @brief This function handles the PWR PVD interrupt request. | |
* @note This API should be called under the PVD_IRQHandler(). | |
* @retval None | |
*/ | |
void HAL_PWR_PVD_IRQHandler(void) | |
{ | |
/* Check PWR Exti flag */ | |
if(__HAL_PWR_PVD_EXTI_GET_FLAG() != RESET) | |
{ | |
/* PWR PVD interrupt user callback */ | |
HAL_PWR_PVDCallback(); | |
/* Clear PWR Exti pending bit */ | |
__HAL_PWR_PVD_EXTI_CLEAR_FLAG(); | |
} | |
} | |
/** | |
* @brief PWR PVD interrupt callback | |
* @retval None | |
*/ | |
__weak void HAL_PWR_PVDCallback(void) | |
{ | |
/* NOTE : This function Should not be modified, when the callback is needed, | |
the HAL_PWR_PVDCallback could be implemented in the user file | |
*/ | |
} | |
/** | |
* @brief Indicates Sleep-On-Exit when returning from Handler mode to Thread mode. | |
* @note Set SLEEPONEXIT bit of SCR register. When this bit is set, the processor | |
* re-enters SLEEP mode when an interruption handling is over. | |
* Setting this bit is useful when the processor is expected to run only on | |
* interruptions handling. | |
* @retval None | |
*/ | |
void HAL_PWR_EnableSleepOnExit(void) | |
{ | |
/* Set SLEEPONEXIT bit of Cortex System Control Register */ | |
SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); | |
} | |
/** | |
* @brief Disables Sleep-On-Exit feature when returning from Handler mode to Thread mode. | |
* @note Clears SLEEPONEXIT bit of SCR register. When this bit is set, the processor | |
* re-enters SLEEP mode when an interruption handling is over. | |
* @retval None | |
*/ | |
void HAL_PWR_DisableSleepOnExit(void) | |
{ | |
/* Clear SLEEPONEXIT bit of Cortex System Control Register */ | |
CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SLEEPONEXIT_Msk)); | |
} | |
/** | |
* @brief Enables CORTEX M4 SEVONPEND bit. | |
* @note Sets SEVONPEND bit of SCR register. When this bit is set, this causes | |
* WFE to wake up when an interrupt moves from inactive to pended. | |
* @retval None | |
*/ | |
void HAL_PWR_EnableSEVOnPend(void) | |
{ | |
/* Set SEVONPEND bit of Cortex System Control Register */ | |
SET_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); | |
} | |
/** | |
* @brief Disables CORTEX M4 SEVONPEND bit. | |
* @note Clears SEVONPEND bit of SCR register. When this bit is set, this causes | |
* WFE to wake up when an interrupt moves from inactive to pended. | |
* @retval None | |
*/ | |
void HAL_PWR_DisableSEVOnPend(void) | |
{ | |
/* Clear SEVONPEND bit of Cortex System Control Register */ | |
CLEAR_BIT(SCB->SCR, ((uint32_t)SCB_SCR_SEVONPEND_Msk)); | |
} | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
#endif /* HAL_PWR_MODULE_ENABLED */ | |
/** | |
* @} | |
*/ | |
/** | |
* @} | |
*/ | |
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ |