blob: 9af9601aea54aafc6ee391c5c9173097cc28236c [file] [log] [blame]
/*
* Copyright (c) 2017 Intel Corporation
*
* SPDX-License-Identifier: Apache-2.0
*/
/* Include esp-idf headers first to avoid redefining BIT() macro */
#include <soc/dport_reg.h>
#include <soc/i2c_reg.h>
#include <rom/gpio.h>
#include <soc/gpio_sig_map.h>
#include <soc.h>
#include <errno.h>
#include <drivers/gpio.h>
#include <gpio/gpio_esp32.h>
#include <drivers/i2c.h>
#include <sys/util.h>
#include <string.h>
/* Number of entries in hardware command queue */
#define I2C_ESP32_NUM_CMDS 16
/* Number of bytes in hardware FIFO */
#define I2C_ESP32_BUFFER_SIZE 32
#define I2C_ESP32_TIMEOUT_MS 100
#define I2C_ESP32_SPIN_THRESHOLD 600
#define I2C_ESP32_YIELD_THRESHOLD (I2C_ESP32_SPIN_THRESHOLD / 2)
#define I2C_ESP32_TIMEOUT \
((I2C_ESP32_YIELD_THRESHOLD) + (I2C_ESP32_SPIN_THRESHOLD))
enum i2c_esp32_opcodes {
I2C_ESP32_OP_RSTART,
I2C_ESP32_OP_WRITE,
I2C_ESP32_OP_READ,
I2C_ESP32_OP_STOP,
I2C_ESP32_OP_END
};
struct i2c_esp32_cmd {
u32_t num_bytes : 8;
u32_t ack_en : 1;
u32_t ack_exp : 1;
u32_t ack_val : 1;
u32_t opcode : 3;
u32_t reserved : 17;
u32_t done : 1;
};
struct i2c_esp32_data {
u32_t dev_config;
u16_t address;
struct k_sem fifo_sem;
struct k_sem transfer_sem;
};
typedef void (*irq_connect_cb)(void);
struct i2c_esp32_config {
int index;
irq_connect_cb connect_irq;
const struct {
int sda_out;
int sda_in;
int scl_out;
int scl_in;
} sig;
const struct {
int scl;
int sda;
} pins;
const struct esp32_peripheral peripheral;
const struct {
bool tx_lsb_first;
bool rx_lsb_first;
} mode;
const struct {
int source;
int line;
} irq;
const u32_t default_config;
};
static int i2c_esp32_configure_pins(int pin, int matrix_out, int matrix_in)
{
const int pin_mode = GPIO_DIR_OUT |
GPIO_DS_DISCONNECT_LOW |
GPIO_PUD_PULL_UP;
const char *device_name = gpio_esp32_get_gpio_for_pin(pin);
struct device *gpio;
int ret;
if (!device_name) {
return -EINVAL;
}
gpio = device_get_binding(device_name);
if (!gpio) {
return -EINVAL;
}
ret = gpio_pin_configure(gpio, pin, pin_mode);
if (ret < 0) {
return ret;
}
ret = gpio_pin_write(gpio, pin, 1);
if (ret < 0) {
return ret;
}
esp32_rom_gpio_matrix_out(pin, matrix_out, false, false);
esp32_rom_gpio_matrix_in(pin, matrix_in, false);
return 0;
}
static int i2c_esp32_configure_speed(const struct i2c_esp32_config *config,
u32_t speed)
{
static const u32_t speed_to_freq_tbl[] = {
[I2C_SPEED_STANDARD] = KHZ(100),
[I2C_SPEED_FAST] = KHZ(400),
[I2C_SPEED_FAST_PLUS] = MHZ(1),
[I2C_SPEED_HIGH] = 0,
[I2C_SPEED_ULTRA] = 0
};
u32_t freq_hz = speed_to_freq_tbl[speed];
u32_t period;
if (!freq_hz) {
return -ENOTSUP;
}
period = (APB_CLK_FREQ / freq_hz);
period /= 2U; /* Set hold and setup times to 1/2th of period */
esp32_set_mask32(period << I2C_SCL_LOW_PERIOD_S,
I2C_SCL_LOW_PERIOD_REG(config->index));
esp32_set_mask32(period << I2C_SCL_HIGH_PERIOD_S,
I2C_SCL_HIGH_PERIOD_REG(config->index));
esp32_set_mask32(period << I2C_SCL_START_HOLD_TIME_S,
I2C_SCL_START_HOLD_REG(config->index));
esp32_set_mask32(period << I2C_SCL_RSTART_SETUP_TIME_S,
I2C_SCL_RSTART_SETUP_REG(config->index));
esp32_set_mask32(period << I2C_SCL_STOP_HOLD_TIME_S,
I2C_SCL_STOP_HOLD_REG(config->index));
esp32_set_mask32(period << I2C_SCL_STOP_SETUP_TIME_S,
I2C_SCL_STOP_SETUP_REG(config->index));
period /= 2U; /* Set sample and hold times to 1/4th of period */
esp32_set_mask32(period << I2C_SDA_HOLD_TIME_S,
I2C_SDA_HOLD_REG(config->index));
esp32_set_mask32(period << I2C_SDA_SAMPLE_TIME_S,
I2C_SDA_SAMPLE_REG(config->index));
return 0;
}
static int i2c_esp32_configure(struct device *dev, u32_t dev_config)
{
const struct i2c_esp32_config *config = dev->config->config_info;
struct i2c_esp32_data *data = dev->driver_data;
unsigned int key = irq_lock();
u32_t v = 0U;
int ret;
ret = i2c_esp32_configure_pins(config->pins.scl,
config->sig.scl_out,
config->sig.scl_in);
if (ret < 0) {
return ret;
}
ret = i2c_esp32_configure_pins(config->pins.sda,
config->sig.sda_out,
config->sig.sda_in);
if (ret < 0) {
return ret;
}
esp32_enable_peripheral(&config->peripheral);
/* MSB or LSB first is configurable for both TX and RX */
if (config->mode.tx_lsb_first) {
v |= I2C_TX_LSB_FIRST;
}
if (config->mode.rx_lsb_first) {
v |= I2C_RX_LSB_FIRST;
}
if (dev_config & I2C_MODE_MASTER) {
v |= I2C_MS_MODE;
sys_write32(0, I2C_SLAVE_ADDR_REG(config->index));
} else {
u32_t addr = (data->address & I2C_SLAVE_ADDR_V);
if (dev_config & I2C_ADDR_10_BITS) {
addr |= I2C_ADDR_10BIT_EN;
}
sys_write32(addr << I2C_SLAVE_ADDR_S,
I2C_SLAVE_ADDR_REG(config->index));
/* Before setting up FIFO and interrupts, stop transmission */
sys_clear_bit(I2C_CTR_REG(config->index), I2C_TRANS_START_S);
/* Byte after address isn't the offset address in slave RAM */
sys_clear_bit(I2C_FIFO_CONF_REG(config->index),
I2C_FIFO_ADDR_CFG_EN_S);
}
/* Use open-drain for clock and data pins */
v |= (I2C_SCL_FORCE_OUT | I2C_SDA_FORCE_OUT);
v |= I2C_CLK_EN;
sys_write32(v, I2C_CTR_REG(config->index));
ret = i2c_esp32_configure_speed(config, I2C_SPEED_GET(dev_config));
if (ret < 0) {
goto out;
}
/* Use FIFO to transmit data */
sys_clear_bit(I2C_FIFO_CONF_REG(config->index), I2C_NONFIFO_EN_S);
v = CONFIG_I2C_ESP32_TIMEOUT & I2C_TIME_OUT_REG;
sys_write32(v << I2C_TIME_OUT_REG_S, I2C_TO_REG(config->index));
/* Enable interrupt types handled by the ISR */
sys_write32(I2C_ACK_ERR_INT_ENA_M |
I2C_TIME_OUT_INT_ENA_M |
I2C_TRANS_COMPLETE_INT_ENA_M |
I2C_ARBITRATION_LOST_INT_ENA_M,
I2C_INT_ENA_REG(config->index));
irq_enable(config->irq.line);
out:
irq_unlock(key);
return ret;
}
static inline void i2c_esp32_reset_fifo(const struct i2c_esp32_config *config)
{
u32_t reg = I2C_FIFO_CONF_REG(config->index);
/* Writing 1 and then 0 to these bits will reset the I2C fifo */
esp32_set_mask32(I2C_TX_FIFO_RST | I2C_RX_FIFO_RST, reg);
esp32_clear_mask32(I2C_TX_FIFO_RST | I2C_RX_FIFO_RST, reg);
}
static int i2c_esp32_spin_yield(int *counter)
{
*counter = *counter + 1;
if (*counter > I2C_ESP32_TIMEOUT) {
return -ETIMEDOUT;
}
if (*counter > I2C_ESP32_SPIN_THRESHOLD) {
k_yield();
}
return 0;
}
static int i2c_esp32_transmit(struct device *dev)
{
const struct i2c_esp32_config *config = dev->config->config_info;
struct i2c_esp32_data *data = dev->driver_data;
u32_t status;
/* Start transmission and wait for the ISR to give the semaphore */
sys_set_bit(I2C_CTR_REG(config->index), I2C_TRANS_START_S);
if (k_sem_take(&data->fifo_sem, I2C_ESP32_TIMEOUT_MS) < 0) {
return -ETIMEDOUT;
}
status = sys_read32(I2C_INT_RAW_REG(config->index));
if (status & (I2C_ARBITRATION_LOST_INT_RAW | I2C_ACK_ERR_INT_RAW)) {
return -EIO;
}
if (status & I2C_TIME_OUT_INT_RAW) {
return -ETIMEDOUT;
}
return 0;
}
static int i2c_esp32_wait(struct device *dev,
volatile struct i2c_esp32_cmd *wait_cmd)
{
const struct i2c_esp32_config *config = dev->config->config_info;
int counter = 0;
int ret;
if (wait_cmd) {
while (!wait_cmd->done) {
ret = i2c_esp32_spin_yield(&counter);
if (ret < 0) {
return ret;
}
}
}
/* Wait for I2C bus to finish its business */
while (sys_read32(I2C_SR_REG(config->index)) & I2C_BUS_BUSY) {
ret = i2c_esp32_spin_yield(&counter);
if (ret < 0) {
return ret;
}
}
return 0;
}
static int i2c_esp32_transmit_wait(struct device *dev,
volatile struct i2c_esp32_cmd *wait_cmd)
{
int ret;
ret = i2c_esp32_transmit(dev);
if (!ret) {
return i2c_esp32_wait(dev, wait_cmd);
}
return ret;
}
static volatile struct i2c_esp32_cmd *
i2c_esp32_write_addr(struct device *dev,
volatile struct i2c_esp32_cmd *cmd,
struct i2c_msg *msg,
u16_t addr)
{
const struct i2c_esp32_config *config = dev->config->config_info;
struct i2c_esp32_data *data = dev->driver_data;
u32_t addr_len = 1U;
i2c_esp32_reset_fifo(config);
sys_write32(addr & I2C_FIFO_RDATA, I2C_DATA_APB_REG(config->index));
if (data->dev_config & I2C_ADDR_10_BITS) {
sys_write32(I2C_DATA_APB_REG(config->index),
(addr >> 8) & I2C_FIFO_RDATA);
addr_len++;
}
if ((msg->flags & I2C_MSG_RW_MASK) != I2C_MSG_WRITE) {
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_WRITE,
.ack_en = true,
.num_bytes = addr_len,
};
} else {
msg->len += addr_len;
}
return cmd;
}
static int i2c_esp32_read_msg(struct device *dev, u16_t addr,
struct i2c_msg msg)
{
const struct i2c_esp32_config *config = dev->config->config_info;
volatile struct i2c_esp32_cmd *cmd =
(void *)I2C_COMD0_REG(config->index);
u32_t i;
int ret;
/* Set the R/W bit to R */
addr |= BIT(0);
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_RSTART
};
cmd = i2c_esp32_write_addr(dev, cmd, &msg, addr);
for (; msg.len; cmd = (void *)I2C_COMD0_REG(config->index)) {
volatile struct i2c_esp32_cmd *wait_cmd = NULL;
u32_t to_read = MIN(I2C_ESP32_BUFFER_SIZE, msg.len - 1);
/* Might be the last byte, in which case, `to_read` will
* be 0 here. See comment below.
*/
if (to_read) {
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_READ,
.num_bytes = to_read,
};
}
/* I2C master won't acknowledge the last byte read from the
* slave device. Divide the read command in two segments as
* recommended by the ESP32 Technical Reference Manual.
*/
if (msg.len - to_read <= 1U) {
/* Read the last byte and explicitly ask for an
* acknowledgment.
*/
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_READ,
.num_bytes = 1,
.ack_val = true,
};
/* Account for the `msg.len - 1` when clamping
* transmission length to FIFO buffer size.
*/
to_read++;
if (msg.flags & I2C_MSG_STOP) {
wait_cmd = cmd;
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_STOP
};
}
}
if (!wait_cmd) {
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_END
};
}
ret = i2c_esp32_transmit_wait(dev, wait_cmd);
if (ret < 0) {
return ret;
}
for (i = 0U; i < to_read; i++) {
u32_t v = sys_read32(I2C_DATA_APB_REG(config->index));
*msg.buf++ = v & I2C_FIFO_RDATA;
}
msg.len -= to_read;
i2c_esp32_reset_fifo(config);
}
return 0;
}
static int i2c_esp32_write_msg(struct device *dev, u16_t addr,
struct i2c_msg msg)
{
const struct i2c_esp32_config *config = dev->config->config_info;
volatile struct i2c_esp32_cmd *cmd =
(void *)I2C_COMD0_REG(config->index);
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_RSTART
};
cmd = i2c_esp32_write_addr(dev, cmd, &msg, addr);
for (; msg.len; cmd = (void *)I2C_COMD0_REG(config->index)) {
u32_t to_send = MIN(I2C_ESP32_BUFFER_SIZE, msg.len);
u32_t i;
int ret;
/* Copy data to TX fifo */
for (i = 0U; i < to_send; i++) {
sys_write32(*msg.buf++,
I2C_DATA_APB_REG(config->index));
}
*cmd++ = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_WRITE,
.num_bytes = to_send,
.ack_en = true,
};
msg.len -= to_send;
if (!msg.len && (msg.flags & I2C_MSG_STOP)) {
*cmd = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_STOP
};
} else {
*cmd = (struct i2c_esp32_cmd) {
.opcode = I2C_ESP32_OP_END
};
}
ret = i2c_esp32_transmit_wait(dev, cmd);
if (ret < 0) {
return ret;
}
i2c_esp32_reset_fifo(config);
}
return 0;
}
static int i2c_esp32_transfer(struct device *dev, struct i2c_msg *msgs,
u8_t num_msgs, u16_t addr)
{
struct i2c_esp32_data *data = dev->driver_data;
int ret = 0;
u8_t i;
k_sem_take(&data->transfer_sem, K_FOREVER);
/* Mask out unused address bits, and make room for R/W bit */
addr &= BIT_MASK(data->dev_config & I2C_ADDR_10_BITS ? 10 : 7);
addr <<= 1;
for (i = 0U; i < num_msgs; i++) {
if ((msgs[i].flags & I2C_MSG_RW_MASK) == I2C_MSG_WRITE) {
ret = i2c_esp32_write_msg(dev, addr, msgs[i]);
} else {
ret = i2c_esp32_read_msg(dev, addr, msgs[i]);
}
if (ret < 0) {
break;
}
}
k_sem_give(&data->transfer_sem);
return ret;
}
static void i2c_esp32_isr(void *arg)
{
const int fifo_give_mask = I2C_ACK_ERR_INT_ST |
I2C_TIME_OUT_INT_ST |
I2C_TRANS_COMPLETE_INT_ST |
I2C_ARBITRATION_LOST_INT_ST;
struct device *device = arg;
const struct i2c_esp32_config *config = device->config->config_info;
if (sys_read32(I2C_INT_STATUS_REG(config->index)) & fifo_give_mask) {
struct i2c_esp32_data *data = device->driver_data;
/* Only give the semaphore if a watched interrupt happens.
* Error checking is performed at the other side of the
* semaphore, by reading the status register.
*/
k_sem_give(&data->fifo_sem);
}
/* Acknowledge all I2C interrupts */
sys_write32(~0, I2C_INT_CLR_REG(config->index));
}
static int i2c_esp32_init(struct device *dev);
static const struct i2c_driver_api i2c_esp32_driver_api = {
.configure = i2c_esp32_configure,
.transfer = i2c_esp32_transfer,
};
#ifdef CONFIG_I2C_0
DEVICE_DECLARE(i2c_esp32_0);
static void i2c_esp32_connect_irq_0(void)
{
IRQ_CONNECT(CONFIG_I2C_ESP32_0_IRQ, 1, i2c_esp32_isr,
DEVICE_GET(i2c_esp32_0), 0);
}
static const struct i2c_esp32_config i2c_esp32_config_0 = {
.index = 0,
.connect_irq = i2c_esp32_connect_irq_0,
.sig = {
.sda_out = I2CEXT0_SDA_OUT_IDX,
.sda_in = I2CEXT0_SDA_IN_IDX,
.scl_out = I2CEXT0_SCL_OUT_IDX,
.scl_in = I2CEXT0_SCL_IN_IDX,
},
.pins = {
.scl = CONFIG_I2C_ESP32_0_SCL_PIN,
.sda = CONFIG_I2C_ESP32_0_SDA_PIN,
},
.peripheral = {
.clk = DPORT_I2C_EXT0_CLK_EN,
.rst = DPORT_I2C_EXT0_RST,
},
.mode = {
.tx_lsb_first =
IS_ENABLED(CONFIG_I2C_ESP32_0_TX_LSB_FIRST),
.rx_lsb_first =
IS_ENABLED(CONFIG_I2C_ESP32_0_RX_LSB_FIRST),
},
.irq = {
.source = ETS_I2C_EXT0_INTR_SOURCE,
.line = CONFIG_I2C_ESP32_0_IRQ,
},
.default_config = CONFIG_I2C_0_DEFAULT_CFG,
};
static struct i2c_esp32_data i2c_esp32_data_0;
DEVICE_AND_API_INIT(i2c_esp32_0, CONFIG_I2C_0_NAME, &i2c_esp32_init,
&i2c_esp32_data_0, &i2c_esp32_config_0,
POST_KERNEL, CONFIG_I2C_INIT_PRIORITY,
&i2c_esp32_driver_api);
#endif /* CONFIG_I2C_0 */
#ifdef CONFIG_I2C_1
DEVICE_DECLARE(i2c_esp32_1);
static void i2c_esp32_connect_irq_1(void)
{
IRQ_CONNECT(CONFIG_I2C_ESP32_1_IRQ, 1, i2c_esp32_isr,
DEVICE_GET(i2c_esp32_1), 0);
}
static const struct i2c_esp32_config i2c_esp32_config_1 = {
.index = 1,
.connect_irq = i2c_esp32_connect_irq_1,
.sig = {
.sda_out = I2CEXT1_SDA_OUT_IDX,
.sda_in = I2CEXT1_SDA_IN_IDX,
.scl_out = I2CEXT1_SCL_OUT_IDX,
.scl_in = I2CEXT1_SCL_IN_IDX,
},
.pins = {
.scl = CONFIG_I2C_ESP32_1_SCL_PIN,
.sda = CONFIG_I2C_ESP32_1_SDA_PIN,
},
.peripheral = {
.clk = DPORT_I2C_EXT1_CLK_EN,
.rst = DPORT_I2C_EXT1_RST,
},
.mode = {
.tx_lsb_first =
IS_ENABLED(CONFIG_I2C_ESP32_1_TX_LSB_FIRST),
.rx_lsb_first =
IS_ENABLED(CONFIG_I2C_ESP32_1_RX_LSB_FIRST),
},
.irq = {
.source = ETS_I2C_EXT1_INTR_SOURCE,
.line = CONFIG_I2C_ESP32_1_IRQ,
},
.default_config = CONFIG_I2C_1_DEFAULT_CFG,
};
static struct i2c_esp32_data i2c_esp32_data_1;
DEVICE_AND_API_INIT(i2c_esp32_1, CONFIG_I2C_1_NAME, &i2c_esp32_init,
&i2c_esp32_data_1, &i2c_esp32_config_1,
POST_KERNEL, CONFIG_I2C_INIT_PRIORITY,
&i2c_esp32_driver_api);
#endif /* CONFIG_I2C_1 */
static int i2c_esp32_init(struct device *dev)
{
const struct i2c_esp32_config *config = dev->config->config_info;
struct i2c_esp32_data *data = dev->driver_data;
unsigned int key = irq_lock();
k_sem_init(&data->fifo_sem, 1, 1);
k_sem_init(&data->transfer_sem, 1, 1);
irq_disable(config->irq.line);
/* Even if irq_enable() is called on config->irq.line, disable
* interrupt sources in the I2C controller.
*/
sys_write32(0, I2C_INT_ENA_REG(config->index));
esp32_rom_intr_matrix_set(0, config->irq.source, config->irq.line);
config->connect_irq();
irq_unlock(key);
return i2c_esp32_configure(dev, config->default_config);
}