| /* |
| * Copyright (c) 2021 Nordic Semiconductor ASA |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| / { |
| chosen { |
| zephyr,console = &uart0; |
| zephyr,shell-uart = &uart0; |
| zephyr,uart-mcumgr = &uart0; |
| zephyr,bt-mon-uart = &uart0; |
| zephyr,bt-c2h-uart = &uart0; |
| }; |
| |
| buttons { |
| compatible = "gpio-keys"; |
| button0: button_0 { |
| gpios = <&gpio1 14 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| label = "Push button 1"; |
| }; |
| button1: button_1 { |
| gpios = <&gpio1 13 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| label = "Push button 2"; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| red_led: led_1 { |
| gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; |
| label = "RGB red LED"; |
| }; |
| green_led: led_2 { |
| gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; |
| label = "RGB green LED"; |
| }; |
| blue_led: led_3 { |
| gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; |
| label = "RGB blue LED"; |
| }; |
| }; |
| |
| pwmleds { |
| compatible = "pwm-leds"; |
| red_led_pwm: led_pwm_0 { |
| pwms = <&pwm0 40>; |
| label = "Red PWM LED"; |
| }; |
| |
| green_led_pwm: led_pwm_1 { |
| pwms = <&pwm0 38>; |
| label = "Green PWM LED"; |
| }; |
| |
| blue_led_pwm: led_pwm_2 { |
| pwms = <&pwm0 39>; |
| label = "Blue PWM LED"; |
| }; |
| }; |
| |
| vbatt { |
| compatible = "voltage-divider"; |
| io-channels = <&adc 2>; |
| output-ohms = <180000>; |
| full-ohms = <(1500000 + 180000)>; |
| power-gpios = <&gpio0 16 0>; |
| }; |
| |
| regulator_3v3: regulator-3v3-ctrl { |
| compatible = "regulator-fixed-sync", "regulator-fixed"; |
| label = "vsys-3v3-ctrl"; |
| regulator-name = "ncp114"; |
| enable-gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; |
| regulator-boot-on; |
| }; |
| |
| sensor_pwr_ctrl: sensor-pwr-ctrl { |
| compatible = "regulator-fixed-sync", "regulator-fixed"; |
| label = "sens-pwr-ctrl"; |
| regulator-name = "tck106ag"; |
| enable-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; |
| regulator-boot-on; |
| }; |
| |
| nrf_radio_fem: fem { |
| compatible = "nordic,nrf21540-fem"; |
| rx-en-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; |
| mode-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; |
| pdn-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; |
| tx-en-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; |
| spi-if = <&nrf_radio_fem_spi>; |
| }; |
| |
| aliases { |
| sw0 = &button0; |
| sw1 = &button1; |
| led0 = &red_led; |
| led1 = &green_led; |
| led2 = &blue_led; |
| pwm-led0 = &red_led_pwm; |
| pwm-led1 = &green_led_pwm; |
| pwm-led2 = &blue_led_pwm; |
| }; |
| }; |
| |
| /* RGB LED control */ |
| &pwm0 { |
| status = "okay"; |
| ch0-pin = <40>; |
| ch1-pin = <38>; |
| ch2-pin = <39>; |
| }; |
| |
| /* Buzzer control */ |
| &pwm1 { |
| status = "okay"; |
| ch0-pin = <47>; |
| }; |
| |
| &adc { |
| status = "okay"; |
| }; |
| |
| &gpiote { |
| status = "okay"; |
| }; |
| |
| &gpio0 { |
| status = "okay"; |
| }; |
| |
| &gpio1 { |
| status = "okay"; |
| }; |
| |
| &i2c1 { |
| compatible = "nordic,nrf-twim"; |
| status = "okay"; |
| sda-pin = <34>; |
| scl-pin = <35>; |
| clock-frequency = <I2C_BITRATE_FAST>; |
| |
| bmm150@10 { |
| compatible = "bosch,bmm150"; |
| label = "BMM150"; |
| reg = <0x10>; |
| }; |
| |
| bh1749@38 { |
| compatible = "rohm,bh1749"; |
| label = "BH1749"; |
| reg = <0x38>; |
| int-gpios = <&gpio1 5 (GPIO_PULL_UP | GPIO_ACTIVE_LOW)>; |
| }; |
| }; |
| |
| &spi3 { |
| compatible = "nordic,nrf-spim"; |
| status = "okay"; |
| sck-pin = <29>; |
| mosi-pin = <28>; |
| miso-pin = <26>; |
| cs-gpios = <&gpio0 22 GPIO_ACTIVE_LOW>, |
| <&gpio1 4 GPIO_ACTIVE_LOW>, |
| <&gpio0 24 GPIO_ACTIVE_LOW>; |
| |
| adxl362: spi-dev-adxl362@0 { |
| compatible = "adi,adxl362"; |
| label = "ADXL362"; |
| spi-max-frequency = <8000000>; |
| reg = <0>; |
| int1-gpios = <&gpio0 19 0>; |
| }; |
| |
| bmi270: spi-dev-bmi270@1 { |
| compatible = "bosch,bmi270"; |
| label = "BMI270"; |
| spi-max-frequency = <8000000>; |
| reg = <1>; |
| int1-gpios = <&gpio0 23 0>; |
| }; |
| |
| nrf_radio_fem_spi: fem_spi@2 { |
| compatible = "nordic,nrf21540-fem-spi"; |
| status = "okay"; |
| reg = <2>; |
| label = "FEM_SPI_IF"; |
| spi-max-frequency = <8000000>; |
| }; |
| }; |
| |
| /* UART0 GPIOs can be configured for other use-cases */ |
| &uart0 { |
| current-speed = <115200>; |
| status = "okay"; |
| tx-pin = <12>; |
| rx-pin = <11>; |
| rts-pin = <10>; |
| cts-pin = <9>; |
| }; |
| |
| &qspi { |
| status = "okay"; |
| sck-pin = <17>; |
| io-pins = <13>, <14>; |
| csn-pins = <18>; |
| mx25r64: mx25r6435f@0 { |
| compatible = "nordic,qspi-nor"; |
| reg = <0>; |
| /* MX25R64 supports only pp and pp4io */ |
| /* Thingy:53 supports only pp and pp2o options */ |
| writeoc = "pp"; |
| /* MX25R64 supports all readoc options */ |
| /* Thingy:53 supports only fastread and read2io options */ |
| readoc = "read2io"; |
| sck-frequency = <8000000>; |
| label = "MX25R64"; |
| jedec-id = [c2 28 17]; |
| sfdp-bfp = [ |
| e5 20 f1 ff ff ff ff 03 44 eb 08 6b 08 3b 04 bb |
| ee ff ff ff ff ff 00 ff ff ff 00 ff 0c 20 0f 52 |
| 10 d8 00 ff 23 72 f5 00 82 ed 04 cc 44 83 68 44 |
| 30 b0 30 b0 f7 c4 d5 5c 00 be 29 ff f0 d0 ff ff |
| ]; |
| size = <67108864>; |
| has-dpd; |
| t-enter-dpd = <10000>; |
| t-exit-dpd = <35000>; |
| }; |
| }; |
| |
| &timer0 { |
| status = "okay"; |
| }; |
| |
| &timer1 { |
| status = "okay"; |
| }; |
| |
| &timer2 { |
| status = "okay"; |
| }; |
| |
| &flash0 { |
| partitions { |
| compatible = "fixed-partitions"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| boot_partition: partition@0 { |
| label = "mcuboot"; |
| reg = <0x00000000 0x00010000>; |
| }; |
| slot0_partition: partition@10000 { |
| label = "image-0"; |
| }; |
| slot0_ns_partition: partition@50000 { |
| label = "image-0-nonsecure"; |
| }; |
| slot1_partition: partition@80000 { |
| label = "image-1"; |
| }; |
| slot1_ns_partition: partition@c0000 { |
| label = "image-1-nonsecure"; |
| }; |
| scratch_partition: partition@f0000 { |
| label = "image-scratch"; |
| reg = <0x000f0000 0xa000>; |
| }; |
| storage_partition: partition@fa000 { |
| label = "storage"; |
| reg = <0x000fa000 0x00006000>; |
| }; |
| }; |
| }; |
| |
| / { |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| sram0_image: image@20000000 { |
| /* Zephyr image(s) memory */ |
| }; |
| |
| sram0_s: image_s@20000000 { |
| /* Secure image memory */ |
| }; |
| |
| sram0_ns: image_ns@20040000 { |
| /* Non-Secure image memory */ |
| }; |
| }; |
| }; |
| |
| /* Include partition configuration file */ |
| #include "thingy53_nrf5340_partition_conf.dts" |