doc/kernel/microkernel/microkernel_semaphores.rst

.. _microkernel_semaphores:

Semaphores
##########

Concepts
********

The microkernel's :dfn:`semaphore` objects are an implementation of traditional
counting semaphores.

Any number of semaphores can be defined in a microkernel system. Each semaphore
has a **name** that uniquely identifies it.

A semaphore starts off with a count of zero. This count is incremented each
time the semaphore is given, and is decremented each time the semaphore is taken.
However, a semaphore cannot be taken when it has a count of zero; this makes
it unavailable.

Semaphores may be given by tasks, fibers, or ISRs.

Semaphores may be taken by tasks only. A task that attempts to take an unavailable
semaphore may wait for the semaphore to be given. Any number of tasks may wait on
an unavailable semaphore simultaneously; and when the semaphore becomes available,
it is given to the highest priority task that has waited the longest.

The kernel allows a task to give multiple semaphores in a single operation using a
*semaphore group*. The task specifies the members of a semaphore group with an array
of semaphore names, terminated by the symbol :c:macro:`ENDLIST`. This technique
allows the task to give the semaphores more efficiently than giving them individually.

A task can also use a semaphore group to take a single semaphore from a set
of semaphores in a single operation. This technique allows the task to
monitor multiple synchronization sources at the same time, similar to the way
:c:func:`select()` can be used to read input from a set of file descriptors
in a POSIX-compliant operating system. The kernel does *not* define the order
in which semaphores are taken when more than one semaphore in a semaphore group
is available; the semaphore that is taken by the task may not be the one
that was given first.

There is no limit on the number of semaphore groups used by a task, or
on the number of semaphores belonging to any given semaphore group. Semaphore
groups may also be shared by multiple tasks, if desired.

Purpose
*******

Use a semaphore to control access to a set of resources by multiple tasks.

Use a semaphore synchronize processing between a producing task, fiber,
or ISR and one or more consuming tasks.

Use a semaphore group to allow a task to signal or to monitor multiple
semaphores simultaneously.

Usage
*****

Defining a Semaphore
====================

The following parameters must be defined:

   *name*
          This specifies a unique name for the semaphore.

Public Semaphore
----------------

Define the semaphore in the application's MDEF with the following syntax:

.. code-block:: console

   SEMA name

For example, the file :file:`projName.mdef` defines two semaphores as follows:

.. code-block:: console

    % SEMA NAME
    % ================
      SEMA INPUT_DATA
      SEMA WORK_DONE

A public semaphore can be referenced by name from any source file that
includes the file :file:`zephyr.h`.

Private Semaphore
-----------------

Define the semaphore in a source file using the following syntax:

.. code-block:: c

   DEFINE_SEMAPHORE(name);

For example, the following code defines a private semaphore named ``PRIV_SEM``.

.. code-block:: c

   DEFINE_SEMAPHORE(PRIV_SEM);

To reference this semaphore from a different source file, use the following syntax:

.. code-block:: c

   extern const ksem_t PRIV_SEM;

Example: Giving a Semaphore from a Task
=======================================

This code uses a semaphore to indicate that a unit of data
is available for processing by a consumer task.

.. code-block:: c

   void producer_task(void)
   {
       /* save data item in a buffer */
       ...

        /* notify task that an additional data item is available */
       task_sem_give(INPUT_DATA);

       ...
   }

Example: Taking a Semaphore with a Conditional Time-out
=======================================================

This code waits up to 500 ticks for a semaphore to be given,
and gives a warning if it is not obtained in that time.

.. code-block:: c

   void consumer_task(void)
   {
       ...

       if (task_sem_take(INPUT_DATA, 500) == RC_TIME) {
           printf("Input data not available!");
       } else {
           /* extract saved data item from buffer and process it */
           ...
       }
       ...
   }

Example: Monitoring Multiple Semaphores at Once
===============================================

This code waits on two semaphores simultaneously, and then takes
action depending on which one was given.

.. code-block:: c

   ksem_t my_sem_group[3] = { INPUT_DATA, WORK_DONE, ENDLIST };

   void consumer_task(void)
   {
       ksem_t sem_id;
       ...

       sem_id = task_sem_group_take(my_sem_group, TICKS_UNLIMITED);
       if (sem_id == WORK_DONE) {
           printf("Shutting down!");
           return;
       } else {
           /* process input data */
           ...
       }
       ...
   }

Example: Giving Multiple Semaphores at Once
===========================================

This code uses a semaphore group to allow a controlling task to signal
the semaphores used by four other tasks in a single operation.

.. code-block:: c

   ksem_t my_sem_group[5] = { SEM1, SEM2, SEM3, SEM4, ENDLIST };

   void control_task(void)
   {
       ...
       task_semaphore_group_give(my_sem_group);
       ...
   }

APIs
****

All of the following APIs are provided by :file:`microkernel.h`:


APIs for an individual semaphore
================================

:cpp:func:`isr_sem_give()`
   Give a semaphore (from an ISR).

:cpp:func:`fiber_sem_give()`
   Give a semaphore (from a fiber).

:cpp:func:`task_sem_give()`
   Give a semaphore.

:cpp:func:`task_sem_take()`
   Take a semaphore, with time limited waiting.

:cpp:func:`task_sem_reset()`
   Set the semaphore count to zero.

:cpp:func:`task_sem_count_get()`
   Read the count for a semaphore.

APIs for semaphore groups
=========================

:cpp:func:`task_sem_group_give()`
   Give each semaphore in a group.

:cpp:func:`task_sem_group_take()`
   Wait up to a specified time period for a semaphore from a group.

:cpp:func:`task_sem_group_reset()`
   Set the count to zero for each semaphore in a group.