| /* |
| * Copyright (c) 2017, NXP |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| /** |
| * @file |
| * @brief System/hardware module for nxp_lpc54114 platform |
| * |
| * This module provides routines to initialize and support board-level |
| * hardware for the nxp_lpc54114 platform. |
| */ |
| |
| #include <kernel.h> |
| #include <device.h> |
| #include <init.h> |
| #include <soc.h> |
| #include <drivers/uart.h> |
| #include <linker/sections.h> |
| #include <arch/cpu.h> |
| #include <cortex_m/exc.h> |
| #include <fsl_power.h> |
| #include <fsl_clock.h> |
| #include <fsl_common.h> |
| #include <fsl_device_registers.h> |
| #include <fsl_pint.h> |
| |
| /** |
| * |
| * @brief Initialize the system clock |
| * |
| * @return N/A |
| * |
| */ |
| |
| static ALWAYS_INLINE void clock_init(void) |
| { |
| |
| #ifdef CONFIG_SOC_LPC54114_M4 |
| /* Set up the clock sources */ |
| |
| /* Ensure FRO is on */ |
| POWER_DisablePD(kPDRUNCFG_PD_FRO_EN); |
| |
| /* |
| * Switch to FRO 12MHz first to ensure we can change voltage without |
| * accidentally being below the voltage for current speed. |
| */ |
| CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); |
| |
| /* Set FLASH wait states for core */ |
| CLOCK_SetFLASHAccessCyclesForFreq(DT_ARM_CORTEX_M4F_0_CLOCK_FREQUENCY); |
| |
| /* Set up high frequency FRO output to selected frequency */ |
| CLOCK_SetupFROClocking(DT_ARM_CORTEX_M4F_0_CLOCK_FREQUENCY); |
| |
| /* Set up dividers */ |
| /* Set AHBCLKDIV divider to value 1 */ |
| CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U, false); |
| |
| /* Set up clock selectors - Attach clocks to the peripheries */ |
| /* Switch MAIN_CLK to FRO_HF */ |
| CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); |
| |
| /* Attach 12 MHz clock to FLEXCOMM0 */ |
| CLOCK_AttachClk(kFRO12M_to_FLEXCOMM0); |
| #endif /* CONFIG_SOC_LPC54114_M4 */ |
| } |
| |
| /** |
| * |
| * @brief Perform basic hardware initialization |
| * |
| * Initialize the interrupt controller device drivers. |
| * Also initialize the timer device driver, if required. |
| * |
| * @return 0 |
| */ |
| |
| static int nxp_lpc54114_init(struct device *arg) |
| { |
| ARG_UNUSED(arg); |
| |
| /* old interrupt lock level */ |
| unsigned int oldLevel; |
| |
| /* disable interrupts */ |
| oldLevel = irq_lock(); |
| |
| /* Initialize FRO/system clock to 48 MHz */ |
| clock_init(); |
| |
| #ifdef CONFIG_GPIO_MCUX_LPC |
| /* Turn on PINT device*/ |
| PINT_Init(PINT); |
| #endif |
| |
| /* |
| * install default handler that simply resets the CPU if configured in |
| * the kernel, NOP otherwise |
| */ |
| NMI_INIT(); |
| |
| /* restore interrupt state */ |
| irq_unlock(oldLevel); |
| |
| return 0; |
| } |
| |
| SYS_INIT(nxp_lpc54114_init, PRE_KERNEL_1, 0); |
| |
| |
| #ifdef CONFIG_SLAVE_CORE_MCUX |
| |
| #define CORE_M0_BOOT_ADDRESS (void *)CONFIG_SLAVE_BOOT_ADDRESS_MCUX |
| |
| static const char core_m0[] = { |
| #include "core-m0.inc" |
| }; |
| |
| /** |
| * |
| * @brief Slave Init |
| * |
| * This routine boots the secondary core |
| * @return N/A |
| */ |
| /* This function is also called at deep sleep resume. */ |
| int _slave_init(struct device *arg) |
| { |
| s32_t temp; |
| |
| ARG_UNUSED(arg); |
| |
| /* Enable SRAM2, used by other core */ |
| SYSCON->AHBCLKCTRLSET[0] = SYSCON_AHBCLKCTRL_SRAM2_MASK; |
| |
| /* Copy second core image to SRAM */ |
| memcpy(CORE_M0_BOOT_ADDRESS, (void *)core_m0, sizeof(core_m0)); |
| |
| /* Setup the reset handler pointer (PC) and stack pointer value. |
| * This is used once the second core runs its startup code. |
| * The second core first boots from flash (address 0x00000000) |
| * and then detects its identity (Cortex-M0, slave) and checks |
| * registers CPBOOT and CPSTACK and use them to continue the |
| * boot process. |
| * Make sure the startup code for current core (Cortex-M4) is |
| * appropriate and shareable with the Cortex-M0 core! |
| */ |
| SYSCON->CPBOOT = SYSCON_CPBOOT_BOOTADDR( |
| *(uint32_t *)((uint8_t *)CORE_M0_BOOT_ADDRESS + 0x4)); |
| SYSCON->CPSTACK = SYSCON_CPSTACK_STACKADDR( |
| *(uint32_t *)CORE_M0_BOOT_ADDRESS); |
| |
| /* Reset the secondary core and start its clocks */ |
| temp = SYSCON->CPUCTRL; |
| temp |= 0xc0c48000; |
| SYSCON->CPUCTRL = (temp | SYSCON_CPUCTRL_CM0CLKEN_MASK |
| | SYSCON_CPUCTRL_CM0RSTEN_MASK); |
| SYSCON->CPUCTRL = (temp | SYSCON_CPUCTRL_CM0CLKEN_MASK) |
| & (~SYSCON_CPUCTRL_CM0RSTEN_MASK); |
| |
| return 0; |
| } |
| |
| SYS_INIT(_slave_init, PRE_KERNEL_2, CONFIG_KERNEL_INIT_PRIORITY_DEFAULT); |
| |
| #endif /*CONFIG_SLAVE_CORE_MCUX*/ |