| .. _sam_e70_xplained: |
| |
| SAM E70(B) Xplained |
| ################### |
| |
| Overview |
| ******** |
| |
| The SAM E70 Xplained evaluation kit is a development platform to evaluate the |
| Atmel SAM E70 series microcontrollers. The current version allows to use both |
| IC variations ATSAME70Q21A(B). |
| |
| .. image:: img/sam_e70_xplained.png |
| :width: 500px |
| :align: center |
| :alt: SAM E70 Xplained |
| |
| Hardware |
| ******** |
| |
| - ATSAME70Q21A(B) ARM Cortex-M7 Processor |
| - 12 MHz crystal oscillator |
| - 32.768 kHz crystal oscillator (not populated) |
| - AT24MAC402 EEPROM |
| - IS42S16100E 16 Mb SDRAM |
| - SD card connector |
| - Ethernet port |
| - Micro-AB USB device |
| - Micro-AB USB debug interface supporting CMSIS-DAP, Virtual COM Port and Data |
| Gateway Interface (DGI) |
| - JTAG interface connector |
| - One reset and one user pushbutton |
| - One green user LED |
| |
| Supported Features |
| ================== |
| |
| The sam_e70_xplained board configuration supports the following hardware |
| features: |
| |
| +-----------+------------+-------------------------------------+ |
| | Interface | Controller | Driver/Component | |
| +===========+============+=====================================+ |
| | NVIC | on-chip | nested vector interrupt controller | |
| +-----------+------------+-------------------------------------+ |
| | SYSTICK | on-chip | systick | |
| +-----------+------------+-------------------------------------+ |
| | UART | on-chip | serial port | |
| +-----------+------------+-------------------------------------+ |
| | USART | on-chip | serial port | |
| +-----------+------------+-------------------------------------+ |
| | I2C | on-chip | i2c | |
| +-----------+------------+-------------------------------------+ |
| | SPI | on-chip | spi | |
| +-----------+------------+-------------------------------------+ |
| | ETHERNET | on-chip | ethernet | |
| +-----------+------------+-------------------------------------+ |
| | WATCHDOG | on-chip | watchdog | |
| +-----------+------------+-------------------------------------+ |
| | GPIO | on-chip | gpio | |
| +-----------+------------+-------------------------------------+ |
| | ADC | on-chip | ADC via AFEC | |
| +-----------+------------+-------------------------------------+ |
| | USB | on-chip | USB device | |
| +-----------+------------+-------------------------------------+ |
| | PWM | on-chip | pwm | |
| +-----------+------------+-------------------------------------+ |
| |
| Other hardware features are not currently supported by Zephyr. |
| |
| The default configuration can be found in the Kconfig |
| :zephyr_file:`boards/arm/sam_e70_xplained/sam_e70_xplained_defconfig`. |
| |
| Connections and IOs |
| =================== |
| |
| The `SAME70-XPLD User Guide`_ has detailed information about board connections. |
| |
| System Clock |
| ============ |
| |
| The SAM E70 MCU is configured to use the 12 MHz external oscillator on the board |
| with the on-chip PLL to generate a 300 MHz system clock. |
| |
| Serial Port |
| =========== |
| |
| The ATSAME70Q21 MCU has five UARTs and three USARTs. One of the USARTs is |
| configured for the console and is available as a Virtual COM Port via EDBG USB |
| chip. |
| |
| Programming and Debugging |
| ************************* |
| |
| Flashing the Zephyr project onto SAM E70 MCU requires the `OpenOCD tool`_. |
| Support for Atmel SAM E microcontroller series was added in OpenOCD release |
| 0.10.0, which was added in Zephyr SDK 0.9.2. |
| |
| By default a factory new SAM E70 chip will boot SAM-BA boot loader located in |
| the ROM, not the flashed image. This is determined by the value of GPNVM1 |
| (General-Purpose NVM bit 1). The flash procedure will ensure that GPNVM1 is |
| set to 1 changing the default behavior to boot from Flash. |
| |
| If your chip has a security bit GPNVM0 set you will be unable to program flash |
| memory or connect to it via a debug interface. The only way to clear GPNVM0 |
| is to perform a chip erase procedure that will erase all GPNVM bits and the full |
| contents of the SAM E70 flash memory: |
| |
| - With the board power off, set a jumper on the J200 header. |
| - Turn the board power on. The jumper can be removed soon after the power is on |
| (flash erasing procedure is started when the erase line is asserted for at |
| least 230ms) |
| |
| Flashing |
| ======== |
| |
| #. Run your favorite terminal program to listen for output. Under Linux the |
| terminal should be :code:`/dev/ttyACM0`. For example: |
| |
| .. code-block:: console |
| |
| $ minicom -D /dev/ttyACM0 -o |
| |
| The -o option tells minicom not to send the modem initialization |
| string. Connection should be configured as follows: |
| |
| - Speed: 115200 |
| - Data: 8 bits |
| - Parity: None |
| - Stop bits: 1 |
| |
| #. Connect the SAM E70 Xplained board to your host computer using the |
| USB debug port. Then build and flash the :ref:`hello_world` |
| application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: sam_e70_xplained |
| :goals: build flash |
| |
| You should see "Hello World! arm" in your terminal. |
| |
| #. To use the SoC variation B IC, you need type "sam_e70b_xplained". |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: sam_e70b_xplained |
| :goals: build flash |
| |
| You can flash the image using an external debug adapter such as J-Link |
| or ULINK, connected to the 20-pin JTAG header. Supply the name of the |
| debug adapter (e.g., ``jlink``) via an OPENOCD_INTERFACE environment |
| variable. OpenOCD will look for the appropriate interface |
| configuration in an ``interface/$(OPENOCD_INTERFACE).cfg`` file on its |
| internal search path. |
| |
| Debugging |
| ========= |
| |
| You can debug an application in the usual way. Here is an example for the |
| :ref:`hello_world` application. |
| |
| .. zephyr-app-commands:: |
| :zephyr-app: samples/hello_world |
| :board: sam_e70_xplained |
| :maybe-skip-config: |
| :goals: debug |
| |
| References |
| ********** |
| |
| SAM E70 Product Page: |
| http://www.atmel.com/products/microcontrollers/arm/sam-e.aspx |
| |
| .. _SAME70-XPLD User Guide: |
| http://www.atmel.com/Images/Atmel-44050-Cortex-M7-Microcontroller-SAM-E70-XPLD-Xplained_User-guide.pdf |
| |
| .. _OpenOCD tool: |
| http://openocd.org/ |
| |
| .. _SAM-BA: |
| http://www.atmel.com/tools/ATMELSAM-BAIN-SYSTEMPROGRAMMER.aspx |