Release v1.1.0
diff --git a/Inc/Legacy/stm32_hal_legacy.h b/Inc/Legacy/stm32_hal_legacy.h
index 41b79bd..5057a2d 100644
--- a/Inc/Legacy/stm32_hal_legacy.h
+++ b/Inc/Legacy/stm32_hal_legacy.h
@@ -7,7 +7,7 @@
******************************************************************************
* @attention
*
- * <h2><center>© Copyright (c) 2020 STMicroelectronics.
+ * <h2><center>© Copyright (c) 2019 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
@@ -23,7 +23,7 @@
#define STM32_HAL_LEGACY
#ifdef __cplusplus
- extern "C" {
+extern "C" {
#endif
/* Includes ------------------------------------------------------------------*/
@@ -38,6 +38,14 @@
#define AES_CLEARFLAG_CCF CRYP_CLEARFLAG_CCF
#define AES_CLEARFLAG_RDERR CRYP_CLEARFLAG_RDERR
#define AES_CLEARFLAG_WRERR CRYP_CLEARFLAG_WRERR
+#if defined(STM32U5)
+#define CRYP_DATATYPE_32B CRYP_NO_SWAP
+#define CRYP_DATATYPE_16B CRYP_HALFWORD_SWAP
+#define CRYP_DATATYPE_8B CRYP_BYTE_SWAP
+#define CRYP_DATATYPE_1B CRYP_BIT_SWAP
+#define CRYP_CCF_CLEAR CRYP_CLEAR_CCF
+#define CRYP_ERR_CLEAR CRYP_CLEAR_RWEIF
+#endif /* STM32U5 */
/**
* @}
*/
@@ -210,6 +218,18 @@
* @}
*/
+/** @defgroup CRC_Aliases CRC API aliases
+ * @{
+ */
+#if defined(STM32WL) || defined(STM32WB) || defined(STM32L5) || defined(STM32L4)
+#else
+#define HAL_CRC_Input_Data_Reverse HAL_CRCEx_Input_Data_Reverse /*!< Aliased to HAL_CRCEx_Input_Data_Reverse for inter STM32 series compatibility */
+#define HAL_CRC_Output_Data_Reverse HAL_CRCEx_Output_Data_Reverse /*!< Aliased to HAL_CRCEx_Output_Data_Reverse for inter STM32 series compatibility */
+#endif
+/**
+ * @}
+ */
+
/** @defgroup HAL_CRC_Aliased_Defines HAL CRC Aliased Defines maintained for legacy purpose
* @{
*/
@@ -235,7 +255,7 @@
#define DAC_WAVEGENERATION_NOISE DAC_WAVE_NOISE
#define DAC_WAVEGENERATION_TRIANGLE DAC_WAVE_TRIANGLE
-#if defined(STM32G4) || defined(STM32H7)
+#if defined(STM32G4) || defined(STM32H7) || defined (STM32U5)
#define DAC_CHIPCONNECT_DISABLE DAC_CHIPCONNECT_EXTERNAL
#define DAC_CHIPCONNECT_ENABLE DAC_CHIPCONNECT_INTERNAL
#endif
@@ -382,7 +402,6 @@
#define DAC_TRIGGER_LP2_OUT DAC_TRIGGER_LPTIM2_OUT
#endif /* STM32H7 */
-
/**
* @}
*/
@@ -470,15 +489,24 @@
#define OB_BOOT_ENTRY_FORCED_FLASH OB_BOOT_LOCK_ENABLE
#endif
#if defined(STM32H7)
-#define FLASH_FLAG_SNECCE_BANK1RR FLASH_FLAG_SNECCERR_BANK1
-#define FLASH_FLAG_DBECCE_BANK1RR FLASH_FLAG_DBECCERR_BANK1
-#define FLASH_FLAG_STRBER_BANK1R FLASH_FLAG_STRBERR_BANK1
-#define FLASH_FLAG_SNECCE_BANK2RR FLASH_FLAG_SNECCERR_BANK2
-#define FLASH_FLAG_DBECCE_BANK2RR FLASH_FLAG_DBECCERR_BANK2
-#define FLASH_FLAG_STRBER_BANK2R FLASH_FLAG_STRBERR_BANK2
-#define FLASH_FLAG_WDW FLASH_FLAG_WBNE
-#define OB_WRP_SECTOR_All OB_WRP_SECTOR_ALL
+#define FLASH_FLAG_SNECCE_BANK1RR FLASH_FLAG_SNECCERR_BANK1
+#define FLASH_FLAG_DBECCE_BANK1RR FLASH_FLAG_DBECCERR_BANK1
+#define FLASH_FLAG_STRBER_BANK1R FLASH_FLAG_STRBERR_BANK1
+#define FLASH_FLAG_SNECCE_BANK2RR FLASH_FLAG_SNECCERR_BANK2
+#define FLASH_FLAG_DBECCE_BANK2RR FLASH_FLAG_DBECCERR_BANK2
+#define FLASH_FLAG_STRBER_BANK2R FLASH_FLAG_STRBERR_BANK2
+#define FLASH_FLAG_WDW FLASH_FLAG_WBNE
+#define OB_WRP_SECTOR_All OB_WRP_SECTOR_ALL
#endif /* STM32H7 */
+#if defined(STM32U5)
+#define OB_USER_nRST_STOP OB_USER_NRST_STOP
+#define OB_USER_nRST_STDBY OB_USER_NRST_STDBY
+#define OB_USER_nRST_SHDW OB_USER_NRST_SHDW
+#define OB_USER_nSWBOOT0 OB_USER_NSWBOOT0
+#define OB_USER_nBOOT0 OB_USER_NBOOT0
+#define OB_nBOOT0_RESET OB_NBOOT0_RESET
+#define OB_nBOOT0_SET OB_NBOOT0_SET
+#endif /* STM32U5 */
/**
* @}
@@ -521,6 +549,7 @@
#define HAL_SYSCFG_EnableIOAnalogSwitchVDD HAL_SYSCFG_EnableIOSwitchVDD
#define HAL_SYSCFG_DisableIOAnalogSwitchVDD HAL_SYSCFG_DisableIOSwitchVDD
#endif /* STM32G4 */
+
/**
* @}
*/
@@ -595,24 +624,24 @@
#define GPIO_AF1_LPTIM GPIO_AF1_LPTIM1
#define GPIO_AF2_LPTIM GPIO_AF2_LPTIM1
-#if defined(STM32L0) || defined(STM32L4) || defined(STM32F4) || defined(STM32F2) || defined(STM32F7) || defined(STM32G4) || defined(STM32H7)
+#if defined(STM32L0) || defined(STM32L4) || defined(STM32F4) || defined(STM32F2) || defined(STM32F7) || defined(STM32G4) || defined(STM32H7) || defined(STM32WB)
#define GPIO_SPEED_LOW GPIO_SPEED_FREQ_LOW
#define GPIO_SPEED_MEDIUM GPIO_SPEED_FREQ_MEDIUM
#define GPIO_SPEED_FAST GPIO_SPEED_FREQ_HIGH
#define GPIO_SPEED_HIGH GPIO_SPEED_FREQ_VERY_HIGH
-#endif /* STM32L0 || STM32L4 || STM32F4 || STM32F2 || STM32F7 || STM32G4 || STM32H7*/
+#endif /* STM32L0 || STM32L4 || STM32F4 || STM32F2 || STM32F7 || STM32G4 || STM32H7 || STM32WB*/
#if defined(STM32L1)
- #define GPIO_SPEED_VERY_LOW GPIO_SPEED_FREQ_LOW
- #define GPIO_SPEED_LOW GPIO_SPEED_FREQ_MEDIUM
- #define GPIO_SPEED_MEDIUM GPIO_SPEED_FREQ_HIGH
- #define GPIO_SPEED_HIGH GPIO_SPEED_FREQ_VERY_HIGH
+#define GPIO_SPEED_VERY_LOW GPIO_SPEED_FREQ_LOW
+#define GPIO_SPEED_LOW GPIO_SPEED_FREQ_MEDIUM
+#define GPIO_SPEED_MEDIUM GPIO_SPEED_FREQ_HIGH
+#define GPIO_SPEED_HIGH GPIO_SPEED_FREQ_VERY_HIGH
#endif /* STM32L1 */
#if defined(STM32F0) || defined(STM32F3) || defined(STM32F1)
- #define GPIO_SPEED_LOW GPIO_SPEED_FREQ_LOW
- #define GPIO_SPEED_MEDIUM GPIO_SPEED_FREQ_MEDIUM
- #define GPIO_SPEED_HIGH GPIO_SPEED_FREQ_HIGH
+#define GPIO_SPEED_LOW GPIO_SPEED_FREQ_LOW
+#define GPIO_SPEED_MEDIUM GPIO_SPEED_FREQ_MEDIUM
+#define GPIO_SPEED_HIGH GPIO_SPEED_FREQ_HIGH
#endif /* STM32F0 || STM32F3 || STM32F1 */
#define GPIO_AF6_DFSDM GPIO_AF6_DFSDM1
@@ -773,49 +802,6 @@
#define HRTIM_EVENTSRC_3 (HRTIM_EECR1_EE1SRC_1)
#define HRTIM_EVENTSRC_4 (HRTIM_EECR1_EE1SRC_1 | HRTIM_EECR1_EE1SRC_0)
-/** @brief Constants defining the events that can be selected to configure the
- * set/reset crossbar of a timer output
- */
-#define HRTIM_OUTPUTSET_TIMEV_1 (HRTIM_SET1R_TIMEVNT1)
-#define HRTIM_OUTPUTSET_TIMEV_2 (HRTIM_SET1R_TIMEVNT2)
-#define HRTIM_OUTPUTSET_TIMEV_3 (HRTIM_SET1R_TIMEVNT3)
-#define HRTIM_OUTPUTSET_TIMEV_4 (HRTIM_SET1R_TIMEVNT4)
-#define HRTIM_OUTPUTSET_TIMEV_5 (HRTIM_SET1R_TIMEVNT5)
-#define HRTIM_OUTPUTSET_TIMEV_6 (HRTIM_SET1R_TIMEVNT6)
-#define HRTIM_OUTPUTSET_TIMEV_7 (HRTIM_SET1R_TIMEVNT7)
-#define HRTIM_OUTPUTSET_TIMEV_8 (HRTIM_SET1R_TIMEVNT8)
-#define HRTIM_OUTPUTSET_TIMEV_9 (HRTIM_SET1R_TIMEVNT9)
-
-#define HRTIM_OUTPUTRESET_TIMEV_1 (HRTIM_RST1R_TIMEVNT1)
-#define HRTIM_OUTPUTRESET_TIMEV_2 (HRTIM_RST1R_TIMEVNT2)
-#define HRTIM_OUTPUTRESET_TIMEV_3 (HRTIM_RST1R_TIMEVNT3)
-#define HRTIM_OUTPUTRESET_TIMEV_4 (HRTIM_RST1R_TIMEVNT4)
-#define HRTIM_OUTPUTRESET_TIMEV_5 (HRTIM_RST1R_TIMEVNT5)
-#define HRTIM_OUTPUTRESET_TIMEV_6 (HRTIM_RST1R_TIMEVNT6)
-#define HRTIM_OUTPUTRESET_TIMEV_7 (HRTIM_RST1R_TIMEVNT7)
-#define HRTIM_OUTPUTRESET_TIMEV_8 (HRTIM_RST1R_TIMEVNT8)
-#define HRTIM_OUTPUTRESET_TIMEV_9 (HRTIM_RST1R_TIMEVNT9)
-
-/** @brief Constants defining the event filtering applied to external events
- * by a timer
- */
-#define HRTIM_TIMEVENTFILTER_NONE (0x00000000U)
-#define HRTIM_TIMEVENTFILTER_BLANKINGCMP1 (HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_BLANKINGCMP2 (HRTIM_EEFR1_EE1FLTR_1)
-#define HRTIM_TIMEVENTFILTER_BLANKINGCMP3 (HRTIM_EEFR1_EE1FLTR_1 | HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_BLANKINGCMP4 (HRTIM_EEFR1_EE1FLTR_2)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR1 (HRTIM_EEFR1_EE1FLTR_2 | HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR2 (HRTIM_EEFR1_EE1FLTR_2 | HRTIM_EEFR1_EE1FLTR_1)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR3 (HRTIM_EEFR1_EE1FLTR_2 | HRTIM_EEFR1_EE1FLTR_1 | HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR4 (HRTIM_EEFR1_EE1FLTR_3)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR5 (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR6 (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_1)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR7 (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_1 | HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_BLANKINGFLTR8 (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_2)
-#define HRTIM_TIMEVENTFILTER_WINDOWINGCMP2 (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_2 | HRTIM_EEFR1_EE1FLTR_0)
-#define HRTIM_TIMEVENTFILTER_WINDOWINGCMP3 (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_2 | HRTIM_EEFR1_EE1FLTR_1)
-#define HRTIM_TIMEVENTFILTER_WINDOWINGTIM (HRTIM_EEFR1_EE1FLTR_3 | HRTIM_EEFR1_EE1FLTR_2 | HRTIM_EEFR1_EE1FLTR_1 | HRTIM_EEFR1_EE1FLTR_0)
-
/** @brief Constants defining the DLL calibration periods (in micro seconds)
*/
#define HRTIM_CALIBRATIONRATE_7300 0x00000000U
@@ -895,7 +881,11 @@
#define LPTIM_TRIGSAMPLETIME_2TRANSITION LPTIM_TRIGSAMPLETIME_2TRANSITIONS
#define LPTIM_TRIGSAMPLETIME_4TRANSITION LPTIM_TRIGSAMPLETIME_4TRANSITIONS
#define LPTIM_TRIGSAMPLETIME_8TRANSITION LPTIM_TRIGSAMPLETIME_8TRANSITIONS
-
+
+#if defined(STM32U5)
+#define LPTIM_ISR_CC1 LPTIM_ISR_CC1IF
+#define LPTIM_ISR_CC2 LPTIM_ISR_CC2IF
+#endif /* STM32U5 */
/**
* @}
*/
@@ -968,6 +958,11 @@
#define HAL_OPAMP_MSP_DEINIT_CB_ID HAL_OPAMP_MSPDEINIT_CB_ID
#endif
+#if defined(STM32L4) || defined(STM32L5)
+#define OPAMP_POWERMODE_NORMAL OPAMP_POWERMODE_NORMALPOWER
+#elif defined(STM32G4)
+#define OPAMP_POWERMODE_NORMAL OPAMP_POWERMODE_NORMALSPEED
+#endif
/**
* @}
@@ -979,15 +974,15 @@
#define I2S_STANDARD_PHILLIPS I2S_STANDARD_PHILIPS
#if defined(STM32H7)
- #define I2S_IT_TXE I2S_IT_TXP
- #define I2S_IT_RXNE I2S_IT_RXP
+#define I2S_IT_TXE I2S_IT_TXP
+#define I2S_IT_RXNE I2S_IT_RXP
- #define I2S_FLAG_TXE I2S_FLAG_TXP
- #define I2S_FLAG_RXNE I2S_FLAG_RXP
+#define I2S_FLAG_TXE I2S_FLAG_TXP
+#define I2S_FLAG_RXNE I2S_FLAG_RXP
#endif
#if defined(STM32F7)
- #define I2S_CLOCK_SYSCLK I2S_CLOCK_PLL
+#define I2S_CLOCK_SYSCLK I2S_CLOCK_PLL
#endif
/**
* @}
@@ -1022,7 +1017,7 @@
/**
* @}
*/
-
+
/** @defgroup HAL_RTC_Aliased_Defines HAL RTC Aliased Defines maintained for legacy purpose
* @{
*/
@@ -1122,16 +1117,16 @@
#if defined(STM32H7)
- #define SPI_FLAG_TXE SPI_FLAG_TXP
- #define SPI_FLAG_RXNE SPI_FLAG_RXP
+#define SPI_FLAG_TXE SPI_FLAG_TXP
+#define SPI_FLAG_RXNE SPI_FLAG_RXP
- #define SPI_IT_TXE SPI_IT_TXP
- #define SPI_IT_RXNE SPI_IT_RXP
+#define SPI_IT_TXE SPI_IT_TXP
+#define SPI_IT_RXNE SPI_IT_RXP
- #define SPI_FRLVL_EMPTY SPI_RX_FIFO_0PACKET
- #define SPI_FRLVL_QUARTER_FULL SPI_RX_FIFO_1PACKET
- #define SPI_FRLVL_HALF_FULL SPI_RX_FIFO_2PACKET
- #define SPI_FRLVL_FULL SPI_RX_FIFO_3PACKET
+#define SPI_FRLVL_EMPTY SPI_RX_FIFO_0PACKET
+#define SPI_FRLVL_QUARTER_FULL SPI_RX_FIFO_1PACKET
+#define SPI_FRLVL_HALF_FULL SPI_RX_FIFO_2PACKET
+#define SPI_FRLVL_FULL SPI_RX_FIFO_3PACKET
#endif /* STM32H7 */
@@ -1417,6 +1412,20 @@
*/
#endif /* STM32L4 || STM32F7 || STM32F4 || STM32H7 */
+#if defined(STM32L4) || defined(STM32F7) || defined(STM32F427xx) || defined(STM32F437xx) \
+ || defined(STM32F429xx) || defined(STM32F439xx) || defined(STM32F469xx) || defined(STM32F479xx) \
+ || defined(STM32H7) || defined(STM32U5)
+/** @defgroup DMA2D_Aliases DMA2D API Aliases
+ * @{
+ */
+#define HAL_DMA2D_DisableCLUT HAL_DMA2D_CLUTLoading_Abort /*!< Aliased to HAL_DMA2D_CLUTLoading_Abort
+ for compatibility with legacy code */
+/**
+ * @}
+ */
+
+#endif /* STM32L4 || STM32F7 || STM32F4 || STM32H7 || STM32U5 */
+
/** @defgroup HAL_PPP_Aliased_Defines HAL PPP Aliased Defines maintained for legacy purpose
* @{
*/
@@ -1435,6 +1444,16 @@
* @}
*/
+#if !defined(STM32F2)
+/** @defgroup HASH_alias HASH API alias
+ * @{
+ */
+#define HAL_HASHEx_IRQHandler HAL_HASH_IRQHandler /*!< Redirection for compatibility with legacy code */
+/**
+ *
+ * @}
+ */
+#endif /* STM32F2 */
/** @defgroup HAL_HASH_Aliased_Functions HAL HASH Aliased Functions maintained for legacy purpose
* @{
*/
@@ -1494,7 +1513,8 @@
#define HAL_DisableDBGStopMode HAL_DBGMCU_DisableDBGStopMode
#define HAL_EnableDBGStandbyMode HAL_DBGMCU_EnableDBGStandbyMode
#define HAL_DisableDBGStandbyMode HAL_DBGMCU_DisableDBGStandbyMode
-#define HAL_DBG_LowPowerConfig(Periph, cmd) (((cmd)==ENABLE)? HAL_DBGMCU_DBG_EnableLowPowerConfig(Periph) : HAL_DBGMCU_DBG_DisableLowPowerConfig(Periph))
+#define HAL_DBG_LowPowerConfig(Periph, cmd) (((cmd\
+ )==ENABLE)? HAL_DBGMCU_DBG_EnableLowPowerConfig(Periph) : HAL_DBGMCU_DBG_DisableLowPowerConfig(Periph))
#define HAL_VREFINT_OutputSelect HAL_SYSCFG_VREFINT_OutputSelect
#define HAL_Lock_Cmd(cmd) (((cmd)==ENABLE) ? HAL_SYSCFG_Enable_Lock_VREFINT() : HAL_SYSCFG_Disable_Lock_VREFINT())
#if defined(STM32L0)
@@ -1502,7 +1522,8 @@
#define HAL_VREFINT_Cmd(cmd) (((cmd)==ENABLE)? HAL_SYSCFG_EnableVREFINT() : HAL_SYSCFG_DisableVREFINT())
#endif
#define HAL_ADC_EnableBuffer_Cmd(cmd) (((cmd)==ENABLE) ? HAL_ADCEx_EnableVREFINT() : HAL_ADCEx_DisableVREFINT())
-#define HAL_ADC_EnableBufferSensor_Cmd(cmd) (((cmd)==ENABLE) ? HAL_ADCEx_EnableVREFINTTempSensor() : HAL_ADCEx_DisableVREFINTTempSensor())
+#define HAL_ADC_EnableBufferSensor_Cmd(cmd) (((cmd\
+ )==ENABLE) ? HAL_ADCEx_EnableVREFINTTempSensor() : HAL_ADCEx_DisableVREFINTTempSensor())
#if defined(STM32H7A3xx) || defined(STM32H7B3xx) || defined(STM32H7B0xx) || defined(STM32H7A3xxQ) || defined(STM32H7B3xxQ) || defined(STM32H7B0xxQ)
#define HAL_EnableSRDomainDBGStopMode HAL_EnableDomain3DBGStopMode
#define HAL_DisableSRDomainDBGStopMode HAL_DisableDomain3DBGStopMode
@@ -1525,9 +1546,9 @@
#define HAL_DATA_EEPROMEx_Erase HAL_FLASHEx_DATAEEPROM_Erase
#define HAL_DATA_EEPROMEx_Program HAL_FLASHEx_DATAEEPROM_Program
- /**
+/**
* @}
- */
+ */
/** @defgroup HAL_I2C_Aliased_Functions HAL I2C Aliased Functions maintained for legacy purpose
* @{
@@ -1537,7 +1558,8 @@
#define HAL_FMPI2CEx_AnalogFilter_Config HAL_FMPI2CEx_ConfigAnalogFilter
#define HAL_FMPI2CEx_DigitalFilter_Config HAL_FMPI2CEx_ConfigDigitalFilter
-#define HAL_I2CFastModePlusConfig(SYSCFG_I2CFastModePlus, cmd) (((cmd)==ENABLE)? HAL_I2CEx_EnableFastModePlus(SYSCFG_I2CFastModePlus): HAL_I2CEx_DisableFastModePlus(SYSCFG_I2CFastModePlus))
+#define HAL_I2CFastModePlusConfig(SYSCFG_I2CFastModePlus, cmd) (((cmd\
+ )==ENABLE)? HAL_I2CEx_EnableFastModePlus(SYSCFG_I2CFastModePlus): HAL_I2CEx_DisableFastModePlus(SYSCFG_I2CFastModePlus))
#if defined(STM32H7) || defined(STM32WB) || defined(STM32G0) || defined(STM32F0) || defined(STM32F1) || defined(STM32F2) || defined(STM32F3) || defined(STM32F4) || defined(STM32F7) || defined(STM32L0) || defined(STM32L4) || defined(STM32L5) || defined(STM32G4) || defined(STM32L1)
#define HAL_I2C_Master_Sequential_Transmit_IT HAL_I2C_Master_Seq_Transmit_IT
@@ -1562,9 +1584,9 @@
#define HAL_FMPI2C_Slave_Sequential_Transmit_DMA HAL_FMPI2C_Slave_Seq_Transmit_DMA
#define HAL_FMPI2C_Slave_Sequential_Receive_DMA HAL_FMPI2C_Slave_Seq_Receive_DMA
#endif /* STM32F4 */
- /**
+/**
* @}
- */
+ */
/** @defgroup HAL_PWR_Aliased HAL PWR Aliased maintained for legacy purpose
* @{
@@ -1619,9 +1641,9 @@
#define PWR_MODE_EVT PWR_PVD_MODE_NORMAL
- /**
+/**
* @}
- */
+ */
/** @defgroup HAL_SMBUS_Aliased_Functions HAL SMBUS Aliased Functions maintained for legacy purpose
* @{
@@ -1870,15 +1892,15 @@
#define __HAL_FREEZE_RTC_DBGMCU __HAL_DBGMCU_FREEZE_RTC
#define __HAL_UNFREEZE_RTC_DBGMCU __HAL_DBGMCU_UNFREEZE_RTC
#if defined(STM32H7)
- #define __HAL_FREEZE_WWDG_DBGMCU __HAL_DBGMCU_FREEZE_WWDG1
- #define __HAL_UNFREEZE_WWDG_DBGMCU __HAL_DBGMCU_UnFreeze_WWDG1
- #define __HAL_FREEZE_IWDG_DBGMCU __HAL_DBGMCU_FREEZE_IWDG1
- #define __HAL_UNFREEZE_IWDG_DBGMCU __HAL_DBGMCU_UnFreeze_IWDG1
+#define __HAL_FREEZE_WWDG_DBGMCU __HAL_DBGMCU_FREEZE_WWDG1
+#define __HAL_UNFREEZE_WWDG_DBGMCU __HAL_DBGMCU_UnFreeze_WWDG1
+#define __HAL_FREEZE_IWDG_DBGMCU __HAL_DBGMCU_FREEZE_IWDG1
+#define __HAL_UNFREEZE_IWDG_DBGMCU __HAL_DBGMCU_UnFreeze_IWDG1
#else
- #define __HAL_FREEZE_WWDG_DBGMCU __HAL_DBGMCU_FREEZE_WWDG
- #define __HAL_UNFREEZE_WWDG_DBGMCU __HAL_DBGMCU_UNFREEZE_WWDG
- #define __HAL_FREEZE_IWDG_DBGMCU __HAL_DBGMCU_FREEZE_IWDG
- #define __HAL_UNFREEZE_IWDG_DBGMCU __HAL_DBGMCU_UNFREEZE_IWDG
+#define __HAL_FREEZE_WWDG_DBGMCU __HAL_DBGMCU_FREEZE_WWDG
+#define __HAL_UNFREEZE_WWDG_DBGMCU __HAL_DBGMCU_UNFREEZE_WWDG
+#define __HAL_FREEZE_IWDG_DBGMCU __HAL_DBGMCU_FREEZE_IWDG
+#define __HAL_UNFREEZE_IWDG_DBGMCU __HAL_DBGMCU_UNFREEZE_IWDG
#endif /* STM32H7 */
#define __HAL_FREEZE_I2C1_TIMEOUT_DBGMCU __HAL_DBGMCU_FREEZE_I2C1_TIMEOUT
#define __HAL_UNFREEZE_I2C1_TIMEOUT_DBGMCU __HAL_DBGMCU_UNFREEZE_I2C1_TIMEOUT
@@ -2089,8 +2111,8 @@
*/
#define IS_DAC_WAVE(WAVE) (((WAVE) == DAC_WAVE_NONE) || \
- ((WAVE) == DAC_WAVE_NOISE)|| \
- ((WAVE) == DAC_WAVE_TRIANGLE))
+ ((WAVE) == DAC_WAVE_NOISE)|| \
+ ((WAVE) == DAC_WAVE_TRIANGLE))
/**
* @}
@@ -2146,7 +2168,7 @@
#define IS_I2S_INSTANCE_EXT IS_I2S_ALL_INSTANCE_EXT
#if defined(STM32H7)
- #define __HAL_I2S_CLEAR_FREFLAG __HAL_I2S_CLEAR_TIFREFLAG
+#define __HAL_I2S_CLEAR_FREFLAG __HAL_I2S_CLEAR_TIFREFLAG
#endif
/**
@@ -2283,7 +2305,8 @@
#define RCC_StopWakeUpClock_HSI RCC_STOP_WAKEUPCLOCK_HSI
#define HAL_RCC_CCSCallback HAL_RCC_CSSCallback
-#define HAL_RC48_EnableBuffer_Cmd(cmd) (((cmd)==ENABLE) ? HAL_RCCEx_EnableHSI48_VREFINT() : HAL_RCCEx_DisableHSI48_VREFINT())
+#define HAL_RC48_EnableBuffer_Cmd(cmd) (((cmd\
+ )==ENABLE) ? HAL_RCCEx_EnableHSI48_VREFINT() : HAL_RCCEx_DisableHSI48_VREFINT())
#define __ADC_CLK_DISABLE __HAL_RCC_ADC_CLK_DISABLE
#define __ADC_CLK_ENABLE __HAL_RCC_ADC_CLK_ENABLE
@@ -3363,7 +3386,20 @@
#define RCC_DFSDM1CLKSOURCE_APB2 RCC_DFSDM1CLKSOURCE_PCLK2
#define RCC_DFSDM2CLKSOURCE_APB2 RCC_DFSDM2CLKSOURCE_PCLK2
#define RCC_FMPI2C1CLKSOURCE_APB RCC_FMPI2C1CLKSOURCE_PCLK1
-
+#if defined(STM32U5)
+#define MSIKPLLModeSEL RCC_MSIKPLL_MODE_SEL
+#define MSISPLLModeSEL RCC_MSISPLL_MODE_SEL
+#define __HAL_RCC_AHB21_CLK_DISABLE __HAL_RCC_AHB2_1_CLK_DISABLE
+#define __HAL_RCC_AHB22_CLK_DISABLE __HAL_RCC_AHB2_2_CLK_DISABLE
+#define __HAL_RCC_AHB1_CLK_Disable_Clear __HAL_RCC_AHB1_CLK_ENABLE
+#define __HAL_RCC_AHB21_CLK_Disable_Clear __HAL_RCC_AHB2_1_CLK_ENABLE
+#define __HAL_RCC_AHB22_CLK_Disable_Clear __HAL_RCC_AHB2_2_CLK_ENABLE
+#define __HAL_RCC_AHB3_CLK_Disable_Clear __HAL_RCC_AHB3_CLK_ENABLE
+#define __HAL_RCC_APB1_CLK_Disable_Clear __HAL_RCC_APB1_CLK_ENABLE
+#define __HAL_RCC_APB2_CLK_Disable_Clear __HAL_RCC_APB2_CLK_ENABLE
+#define __HAL_RCC_APB3_CLK_Disable_Clear __HAL_RCC_APB3_CLK_ENABLE
+#define IS_RCC_MSIPLLModeSelection IS_RCC_MSIPLLMODE_SELECT
+#endif
/**
* @}
*/
@@ -3380,7 +3416,7 @@
/** @defgroup HAL_RTC_Aliased_Macros HAL RTC Aliased Macros maintained for legacy purpose
* @{
*/
-#if defined (STM32G0) || defined (STM32L5) || defined (STM32L412xx) || defined (STM32L422xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32G4) || defined (STM32WL)
+#if defined (STM32G0) || defined (STM32L5) || defined (STM32L412xx) || defined (STM32L422xx) || defined (STM32L4P5xx) || defined (STM32L4Q5xx) || defined (STM32G4) || defined (STM32WL) || defined (STM32U5)
#else
#define __HAL_RTC_CLEAR_FLAG __HAL_RTC_EXTI_CLEAR_FLAG
#endif
@@ -3400,19 +3436,19 @@
#else
#define __HAL_RTC_EXTI_CLEAR_FLAG(__EXTI_LINE__) (((__EXTI_LINE__) == RTC_EXTI_LINE_ALARM_EVENT) ? __HAL_RTC_ALARM_EXTI_CLEAR_FLAG() : \
(((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_CLEAR_FLAG() : \
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG()))
+ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_CLEAR_FLAG()))
#define __HAL_RTC_EXTI_ENABLE_IT(__EXTI_LINE__) (((__EXTI_LINE__) == RTC_EXTI_LINE_ALARM_EVENT) ? __HAL_RTC_ALARM_EXTI_ENABLE_IT() : \
- (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT() : \
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT()))
+ (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_ENABLE_IT() : \
+ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_ENABLE_IT()))
#define __HAL_RTC_EXTI_DISABLE_IT(__EXTI_LINE__) (((__EXTI_LINE__) == RTC_EXTI_LINE_ALARM_EVENT) ? __HAL_RTC_ALARM_EXTI_DISABLE_IT() : \
- (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_IT() : \
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_DISABLE_IT()))
+ (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_DISABLE_IT() : \
+ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_DISABLE_IT()))
#define __HAL_RTC_EXTI_GET_FLAG(__EXTI_LINE__) (((__EXTI_LINE__) == RTC_EXTI_LINE_ALARM_EVENT) ? __HAL_RTC_ALARM_EXTI_GET_FLAG() : \
- (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_GET_FLAG() : \
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_GET_FLAG()))
+ (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_GET_FLAG() : \
+ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_GET_FLAG()))
#define __HAL_RTC_EXTI_GENERATE_SWIT(__EXTI_LINE__) (((__EXTI_LINE__) == RTC_EXTI_LINE_ALARM_EVENT) ? __HAL_RTC_ALARM_EXTI_GENERATE_SWIT() : \
- (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_GENERATE_SWIT() : \
- __HAL_RTC_TAMPER_TIMESTAMP_EXTI_GENERATE_SWIT()))
+ (((__EXTI_LINE__) == RTC_EXTI_LINE_WAKEUPTIMER_EVENT) ? __HAL_RTC_WAKEUPTIMER_EXTI_GENERATE_SWIT() : \
+ __HAL_RTC_TAMPER_TIMESTAMP_EXTI_GENERATE_SWIT()))
#endif /* STM32F1 */
#define IS_ALARM IS_RTC_ALARM
@@ -3437,13 +3473,17 @@
* @}
*/
-/** @defgroup HAL_SD_Aliased_Macros HAL SD Aliased Macros maintained for legacy purpose
+/** @defgroup HAL_SD_Aliased_Macros HAL SD/MMC Aliased Macros maintained for legacy purpose
* @{
*/
#define SD_OCR_CID_CSD_OVERWRIETE SD_OCR_CID_CSD_OVERWRITE
#define SD_CMD_SD_APP_STAUS SD_CMD_SD_APP_STATUS
+#define eMMC_HIGH_VOLTAGE_RANGE EMMC_HIGH_VOLTAGE_RANGE
+#define eMMC_DUAL_VOLTAGE_RANGE EMMC_DUAL_VOLTAGE_RANGE
+#define eMMC_LOW_VOLTAGE_RANGE EMMC_LOW_VOLTAGE_RANGE
+
#if defined(STM32F4) || defined(STM32F2)
#define SD_SDMMC_DISABLED SD_SDIO_DISABLED
#define SD_SDMMC_FUNCTION_BUSY SD_SDIO_FUNCTION_BUSY
@@ -3596,6 +3636,13 @@
#define __HAL_USART_GETCLOCKSOURCE USART_GETCLOCKSOURCE
#define __USART_GETCLOCKSOURCE USART_GETCLOCKSOURCE
+#if defined(STM32F0) || defined(STM32F3) || defined(STM32F7)
+#define USART_OVERSAMPLING_16 0x00000000U
+#define USART_OVERSAMPLING_8 USART_CR1_OVER8
+
+#define IS_USART_OVERSAMPLING(__SAMPLING__) (((__SAMPLING__) == USART_OVERSAMPLING_16) || \
+ ((__SAMPLING__) == USART_OVERSAMPLING_8))
+#endif /* STM32F0 || STM32F3 || STM32F7 */
/**
* @}
*/
diff --git a/Inc/stm32wlxx_hal_adc.h b/Inc/stm32wlxx_hal_adc.h
index e0188e0..598e5fd 100644
--- a/Inc/stm32wlxx_hal_adc.h
+++ b/Inc/stm32wlxx_hal_adc.h
@@ -132,8 +132,7 @@
FunctionalState LowPowerAutoPowerOff; /*!< Select the auto-off mode: the ADC automatically powers-off after a conversion and automatically wakes-up when a new conversion is triggered (with startup time between trigger and start of sampling).
This feature can be combined with automatic wait mode (parameter 'LowPowerAutoWait').
- This parameter can be set to ENABLE or DISABLE.
- Note: If enabled, this feature also turns off the ADC dedicated 14 MHz RC oscillator (HSI14) */
+ This parameter can be set to ENABLE or DISABLE. */
FunctionalState ContinuousConvMode; /*!< Specify whether the conversion is performed in single mode (one conversion) or continuous mode for ADC group regular,
after the first ADC conversion start trigger occurred (software start or external trigger).
@@ -473,7 +472,7 @@
/** @defgroup ADC_HAL_EC_DATA_ALIGN ADC conversion data alignment
* @{
*/
-#define ADC_DATAALIGN_RIGHT (LL_ADC_DATA_ALIGN_RIGHT)/*!< ADC conversion data alignment: right aligned (alignment on data register LSB bit 0)*/
+#define ADC_DATAALIGN_RIGHT (LL_ADC_DATA_ALIGN_RIGHT) /*!< ADC conversion data alignment: right aligned (alignment on data register LSB bit 0)*/
#define ADC_DATAALIGN_LEFT (LL_ADC_DATA_ALIGN_LEFT) /*!< ADC conversion data alignment: left aligned (alignment on data register MSB bit 15)*/
/**
* @}
@@ -1668,8 +1667,8 @@
* @{
*/
/* Peripheral Control functions ***********************************************/
-HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef *hadc, ADC_ChannelConfTypeDef *sConfig);
-HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef *hadc, ADC_AnalogWDGConfTypeDef *AnalogWDGConfig);
+HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef *hadc, ADC_ChannelConfTypeDef *pConfig);
+HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef *hadc, ADC_AnalogWDGConfTypeDef *pAnalogWDGConfig);
/**
* @}
diff --git a/Inc/stm32wlxx_hal_cortex.h b/Inc/stm32wlxx_hal_cortex.h
index 2b2fe2d..9797364 100644
--- a/Inc/stm32wlxx_hal_cortex.h
+++ b/Inc/stm32wlxx_hal_cortex.h
@@ -187,9 +187,12 @@
/** @defgroup CORTEX_MPU_Region_Size CORTEX MPU Region Size
* @{
*/
+#if defined(CORE_CM0PLUS)
+#else
#define MPU_REGION_SIZE_32B ((uint8_t)0x04)
#define MPU_REGION_SIZE_64B ((uint8_t)0x05)
#define MPU_REGION_SIZE_128B ((uint8_t)0x06)
+#endif
#define MPU_REGION_SIZE_256B ((uint8_t)0x07)
#define MPU_REGION_SIZE_512B ((uint8_t)0x08)
#define MPU_REGION_SIZE_1KB ((uint8_t)0x09)
@@ -379,6 +382,33 @@
((NUMBER) == MPU_REGION_NUMBER6) || \
((NUMBER) == MPU_REGION_NUMBER7))
+#if defined(CORE_CM0PLUS)
+#define IS_MPU_REGION_SIZE(SIZE) (((SIZE) == MPU_REGION_SIZE_256B) || \
+ ((SIZE) == MPU_REGION_SIZE_512B) || \
+ ((SIZE) == MPU_REGION_SIZE_1KB) || \
+ ((SIZE) == MPU_REGION_SIZE_2KB) || \
+ ((SIZE) == MPU_REGION_SIZE_4KB) || \
+ ((SIZE) == MPU_REGION_SIZE_8KB) || \
+ ((SIZE) == MPU_REGION_SIZE_16KB) || \
+ ((SIZE) == MPU_REGION_SIZE_32KB) || \
+ ((SIZE) == MPU_REGION_SIZE_64KB) || \
+ ((SIZE) == MPU_REGION_SIZE_128KB) || \
+ ((SIZE) == MPU_REGION_SIZE_256KB) || \
+ ((SIZE) == MPU_REGION_SIZE_512KB) || \
+ ((SIZE) == MPU_REGION_SIZE_1MB) || \
+ ((SIZE) == MPU_REGION_SIZE_2MB) || \
+ ((SIZE) == MPU_REGION_SIZE_4MB) || \
+ ((SIZE) == MPU_REGION_SIZE_8MB) || \
+ ((SIZE) == MPU_REGION_SIZE_16MB) || \
+ ((SIZE) == MPU_REGION_SIZE_32MB) || \
+ ((SIZE) == MPU_REGION_SIZE_64MB) || \
+ ((SIZE) == MPU_REGION_SIZE_128MB) || \
+ ((SIZE) == MPU_REGION_SIZE_256MB) || \
+ ((SIZE) == MPU_REGION_SIZE_512MB) || \
+ ((SIZE) == MPU_REGION_SIZE_1GB) || \
+ ((SIZE) == MPU_REGION_SIZE_2GB) || \
+ ((SIZE) == MPU_REGION_SIZE_4GB))
+#else
#define IS_MPU_REGION_SIZE(SIZE) (((SIZE) == MPU_REGION_SIZE_32B) || \
((SIZE) == MPU_REGION_SIZE_64B) || \
((SIZE) == MPU_REGION_SIZE_128B) || \
@@ -407,7 +437,7 @@
((SIZE) == MPU_REGION_SIZE_1GB) || \
((SIZE) == MPU_REGION_SIZE_2GB) || \
((SIZE) == MPU_REGION_SIZE_4GB))
-
+#endif
#define IS_MPU_SUB_REGION_DISABLE(SUBREGION) ((SUBREGION) < (uint16_t)0x00FFU)
#endif /* __MPU_PRESENT */
diff --git a/Inc/stm32wlxx_hal_def.h b/Inc/stm32wlxx_hal_def.h
index 0cd2aed..010f9e0 100644
--- a/Inc/stm32wlxx_hal_def.h
+++ b/Inc/stm32wlxx_hal_def.h
@@ -28,7 +28,7 @@
/* Includes ------------------------------------------------------------------*/
#include "stm32wlxx.h"
-#include "Legacy/stm32_hal_legacy.h" /* Aliases file for old names compatibility */
+#include "Legacy/stm32_hal_legacy.h" /* Aliases file for old names compatibility */
#include <stddef.h>
/* Exported types ------------------------------------------------------------*/
diff --git a/Inc/stm32wlxx_hal_dma.h b/Inc/stm32wlxx_hal_dma.h
index d2b5dd6..d281ed4 100644
--- a/Inc/stm32wlxx_hal_dma.h
+++ b/Inc/stm32wlxx_hal_dma.h
@@ -347,7 +347,7 @@
/** @defgroup DMA_Channel_Attributes DMA Channel Attributes
* @brief DMA channel secure or non-secure and privileged or non-privileged attributes
* @note Secure and non-secure attributes are only available from secure when the system
- * implements the security (TZEN=1)
+ * implements the security (ESE=1)
* @{
*/
diff --git a/Inc/stm32wlxx_hal_flash.h b/Inc/stm32wlxx_hal_flash.h
index c920de4..0fbe16b 100644
--- a/Inc/stm32wlxx_hal_flash.h
+++ b/Inc/stm32wlxx_hal_flash.h
@@ -123,7 +123,7 @@
uint32_t C2DebugAccessMode; /*!< CPU2 debug access enabled or disabled (used for OPTIONBYTE_C2_DEBUG_ACCESS).
This parameter can be a value of @ref FLASH_OB_C2_DEBUG_ACCESS */
uint32_t C2BootRegion; /*!< CPU2 Secure Boot memory region(used for OPTIONBYTE_C2_BOOT_VECT).
- This parameter can be a value of @ref C2_FLASH_OB_BOOT_REGION */
+ This parameter can be a value of @ref FLASH_OB_C2_BOOT_REGION */
uint32_t C2SecureBootVectAddr; /*!< CPU2 Secure Boot reset vector (used for OPTIONBYTE_C2_BOOT_VECT).
This parameter contains the CPU2 boot reset start address within
the selected memory region. Make sure this parameter is word aligned. */
@@ -561,7 +561,7 @@
* @}
*/
-/** @defgroup C2_FLASH_OB_BOOT_REGION CPU2 Option Bytes Reset Boot Vector
+/** @defgroup FLASH_OB_C2_BOOT_REGION CPU2 Option Bytes Reset Boot Vector
* @{
*/
#define OB_C2_BOOT_FROM_SRAM 0x00000000U /*!< CPU2 boot from SRAM1 or SRAM2 */
diff --git a/Inc/stm32wlxx_hal_gpio.h b/Inc/stm32wlxx_hal_gpio.h
index 88c85b3..332a7c3 100644
--- a/Inc/stm32wlxx_hal_gpio.h
+++ b/Inc/stm32wlxx_hal_gpio.h
@@ -107,26 +107,25 @@
/** @defgroup GPIO_mode GPIO mode
* @brief GPIO Configuration Mode
- * Elements values convention: 0xX0yz00YZ
- * - X : GPIO mode or EXTI Mode
- * - y : External IT or Event trigger detection
- * - z : IO configuration on External IT or Event
- * - Y : Output type (Push Pull or Open Drain)
- * - Z : IO Direction mode (Input, Output, Alternate or Analog)
+ * Elements values convention: 0x00WX00YZ
+ * - W : EXTI trigger detection on 3 bits
+ * - X : EXTI mode (IT or Event) on 2 bits
+ * - Y : Output type (Push Pull or Open Drain) on 1 bit
+ * - Z : GPIO mode (Input, Output, Alternate or Analog) on 2 bits
* @{
*/
-#define GPIO_MODE_INPUT (0x00000000U) /*!< Input Floating Mode */
-#define GPIO_MODE_OUTPUT_PP (0x00000001U) /*!< Output Push Pull Mode */
-#define GPIO_MODE_OUTPUT_OD (0x00000011U) /*!< Output Open Drain Mode */
-#define GPIO_MODE_AF_PP (0x00000002U) /*!< Alternate Function Push Pull Mode */
-#define GPIO_MODE_AF_OD (0x00000012U) /*!< Alternate Function Open Drain Mode */
-#define GPIO_MODE_ANALOG (0x00000003U) /*!< Analog Mode */
-#define GPIO_MODE_IT_RISING (0x10110000U) /*!< External Interrupt Mode with Rising edge trigger detection */
-#define GPIO_MODE_IT_FALLING (0x10210000U) /*!< External Interrupt Mode with Falling edge trigger detection */
-#define GPIO_MODE_IT_RISING_FALLING (0x10310000U) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
-#define GPIO_MODE_EVT_RISING (0x10120000U) /*!< External Event Mode with Rising edge trigger detection */
-#define GPIO_MODE_EVT_FALLING (0x10220000U) /*!< External Event Mode with Falling edge trigger detection */
-#define GPIO_MODE_EVT_RISING_FALLING (0x10320000U) /*!< External Event Mode with Rising/Falling edge trigger detection */
+#define GPIO_MODE_INPUT MODE_INPUT /*!< Input Floating Mode */
+#define GPIO_MODE_OUTPUT_PP (MODE_OUTPUT | OUTPUT_PP) /*!< Output Push Pull Mode */
+#define GPIO_MODE_OUTPUT_OD (MODE_OUTPUT | OUTPUT_OD) /*!< Output Open Drain Mode */
+#define GPIO_MODE_AF_PP (MODE_AF | OUTPUT_PP) /*!< Alternate Function Push Pull Mode */
+#define GPIO_MODE_AF_OD (MODE_AF | OUTPUT_OD) /*!< Alternate Function Open Drain Mode */
+#define GPIO_MODE_ANALOG MODE_ANALOG /*!< Analog Mode */
+#define GPIO_MODE_IT_RISING (MODE_INPUT | EXTI_IT | TRIGGER_RISING) /*!< External Interrupt Mode with Rising edge trigger detection */
+#define GPIO_MODE_IT_FALLING (MODE_INPUT | EXTI_IT | TRIGGER_FALLING) /*!< External Interrupt Mode with Falling edge trigger detection */
+#define GPIO_MODE_IT_RISING_FALLING (MODE_INPUT | EXTI_IT | TRIGGER_RISING | TRIGGER_FALLING) /*!< External Interrupt Mode with Rising/Falling edge trigger detection */
+#define GPIO_MODE_EVT_RISING (MODE_INPUT | EXTI_EVT | TRIGGER_RISING) /*!< External Event Mode with Rising edge trigger detection */
+#define GPIO_MODE_EVT_FALLING (MODE_INPUT | EXTI_EVT | TRIGGER_FALLING) /*!< External Event Mode with Falling edge trigger detection */
+#define GPIO_MODE_EVT_RISING_FALLING (MODE_INPUT | EXTI_EVT | TRIGGER_RISING | TRIGGER_FALLING) /*!< External Event Mode with Rising/Falling edge trigger detection */
/**
* @}
*/
@@ -135,10 +134,10 @@
* @brief GPIO Output Maximum frequency
* @{
*/
-#define GPIO_SPEED_FREQ_LOW (0x00000000U) /*!< Low speed */
-#define GPIO_SPEED_FREQ_MEDIUM (0x00000001U) /*!< Medium speed */
-#define GPIO_SPEED_FREQ_HIGH (0x00000002U) /*!< High speed */
-#define GPIO_SPEED_FREQ_VERY_HIGH (0x00000003U) /*!< Very high speed */
+#define GPIO_SPEED_FREQ_LOW 0x00000000u /*!< Low speed */
+#define GPIO_SPEED_FREQ_MEDIUM 0x00000001u /*!< Medium speed */
+#define GPIO_SPEED_FREQ_HIGH 0x00000002u /*!< High speed */
+#define GPIO_SPEED_FREQ_VERY_HIGH 0x00000003u /*!< Very high speed */
/**
* @}
*/
@@ -147,9 +146,9 @@
* @brief GPIO Pull-Up or Pull-Down Activation
* @{
*/
-#define GPIO_NOPULL (0x00000000U) /*!< No Pull-up or Pull-down activation */
-#define GPIO_PULLUP (0x00000001U) /*!< Pull-up activation */
-#define GPIO_PULLDOWN (0x00000002U) /*!< Pull-down activation */
+#define GPIO_NOPULL 0x00000000u /*!< No Pull-up or Pull-down activation */
+#define GPIO_PULLUP 0x00000001u /*!< Pull-up activation */
+#define GPIO_PULLDOWN 0x00000002u /*!< Pull-down activation */
/**
* @}
*/
@@ -208,6 +207,32 @@
*/
/* Private macros ------------------------------------------------------------*/
+/** @defgroup GPIO_Private_Constants GPIO Private Constants
+ * @{
+ */
+#define GPIO_MODE_Pos 0u
+#define GPIO_MODE (0x3uL << GPIO_MODE_Pos)
+#define MODE_INPUT (0x0uL << GPIO_MODE_Pos)
+#define MODE_OUTPUT (0x1uL << GPIO_MODE_Pos)
+#define MODE_AF (0x2uL << GPIO_MODE_Pos)
+#define MODE_ANALOG (0x3uL << GPIO_MODE_Pos)
+#define OUTPUT_TYPE_Pos 4u
+#define OUTPUT_TYPE (0x1uL << OUTPUT_TYPE_Pos)
+#define OUTPUT_PP (0x0uL << OUTPUT_TYPE_Pos)
+#define OUTPUT_OD (0x1uL << OUTPUT_TYPE_Pos)
+#define EXTI_MODE_Pos 16u
+#define EXTI_MODE (0x3uL << EXTI_MODE_Pos)
+#define EXTI_IT (0x1uL << EXTI_MODE_Pos)
+#define EXTI_EVT (0x2uL << EXTI_MODE_Pos)
+#define TRIGGER_MODE_Pos 20u
+#define TRIGGER_MODE (0x7uL << TRIGGER_MODE_Pos)
+#define TRIGGER_RISING (0x1uL << TRIGGER_MODE_Pos)
+#define TRIGGER_FALLING (0x2uL << TRIGGER_MODE_Pos)
+
+/**
+ * @}
+ */
+
/** @defgroup GPIO_Private_Macros GPIO Private Macros
* @{
*/
diff --git a/Inc/stm32wlxx_hal_gtzc.h b/Inc/stm32wlxx_hal_gtzc.h
index 71fe39c..d3aa3be 100644
--- a/Inc/stm32wlxx_hal_gtzc.h
+++ b/Inc/stm32wlxx_hal_gtzc.h
@@ -121,7 +121,7 @@
* @note that two maximum values are also defined here:
* - max number of securable AHB/APB peripherals or masters (used in
* TZSC sub-block)
- * - max number of securable and TrustZone-aware AHB/APB peripherals
+ * - max number of securable and security-aware AHB/APB peripherals
* or masters (used in TZIC sub-block)
* @{
*/
@@ -146,7 +146,7 @@
/* Note that two maximum values are also defined here:
* - max number of securable peripherals
* (used in TZSC sub-block)
- * - max number of securable and TrustZone-aware peripherals or masters
+ * - max number of securable and security-aware peripherals or masters
* (used in TZIC sub-block)
*/
#define GTZC_TZSC_PERIPH_NUMBER 4U
diff --git a/Inc/stm32wlxx_hal_hsem.h b/Inc/stm32wlxx_hal_hsem.h
index 44ff408..3455d0e 100644
--- a/Inc/stm32wlxx_hal_hsem.h
+++ b/Inc/stm32wlxx_hal_hsem.h
@@ -43,7 +43,7 @@
/**
* @brief SemID to mask helper Macro.
- * @param __SEMID__: semaphore ID from 0 to 31
+ * @param __SEMID__: semaphore ID from 0 to 15
* @retval Semaphore Mask.
*/
#define __HAL_HSEM_SEMID_TO_MASK(__SEMID__) (1 << (__SEMID__))
diff --git a/Inc/stm32wlxx_hal_i2c.h b/Inc/stm32wlxx_hal_i2c.h
index 52884b3..ce949ac 100644
--- a/Inc/stm32wlxx_hal_i2c.h
+++ b/Inc/stm32wlxx_hal_i2c.h
@@ -48,29 +48,30 @@
typedef struct
{
uint32_t Timing; /*!< Specifies the I2C_TIMINGR_register value.
- This parameter calculated by referring to I2C initialization
- section in Reference manual */
+ This parameter calculated by referring to I2C initialization section
+ in Reference manual */
uint32_t OwnAddress1; /*!< Specifies the first device own address.
- This parameter can be a 7-bit or 10-bit address. */
+ This parameter can be a 7-bit or 10-bit address. */
uint32_t AddressingMode; /*!< Specifies if 7-bit or 10-bit addressing mode is selected.
- This parameter can be a value of @ref I2C_ADDRESSING_MODE */
+ This parameter can be a value of @ref I2C_ADDRESSING_MODE */
uint32_t DualAddressMode; /*!< Specifies if dual addressing mode is selected.
- This parameter can be a value of @ref I2C_DUAL_ADDRESSING_MODE */
+ This parameter can be a value of @ref I2C_DUAL_ADDRESSING_MODE */
uint32_t OwnAddress2; /*!< Specifies the second device own address if dual addressing mode is selected
- This parameter can be a 7-bit address. */
+ This parameter can be a 7-bit address. */
- uint32_t OwnAddress2Masks; /*!< Specifies the acknowledge mask address second device own address if dual addressing mode is selected
- This parameter can be a value of @ref I2C_OWN_ADDRESS2_MASKS */
+ uint32_t OwnAddress2Masks; /*!< Specifies the acknowledge mask address second device own address if dual addressing
+ mode is selected.
+ This parameter can be a value of @ref I2C_OWN_ADDRESS2_MASKS */
uint32_t GeneralCallMode; /*!< Specifies if general call mode is selected.
- This parameter can be a value of @ref I2C_GENERAL_CALL_ADDRESSING_MODE */
+ This parameter can be a value of @ref I2C_GENERAL_CALL_ADDRESSING_MODE */
uint32_t NoStretchMode; /*!< Specifies if nostretch mode is selected.
- This parameter can be a value of @ref I2C_NOSTRETCH_MODE */
+ This parameter can be a value of @ref I2C_NOSTRETCH_MODE */
} I2C_InitTypeDef;
@@ -200,7 +201,8 @@
__IO uint32_t PreviousState; /*!< I2C communication Previous state */
- HAL_StatusTypeDef(*XferISR)(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources); /*!< I2C transfer IRQ handler function pointer */
+ HAL_StatusTypeDef(*XferISR)(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
+ /*!< I2C transfer IRQ handler function pointer */
DMA_HandleTypeDef *hdmatx; /*!< I2C Tx DMA handle parameters */
@@ -217,20 +219,32 @@
__IO uint32_t AddrEventCount; /*!< I2C Address Event counter */
#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
- void (* MasterTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Master Tx Transfer completed callback */
- void (* MasterRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Master Rx Transfer completed callback */
- void (* SlaveTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Slave Tx Transfer completed callback */
- void (* SlaveRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Slave Rx Transfer completed callback */
- void (* ListenCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Listen Complete callback */
- void (* MemTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Memory Tx Transfer completed callback */
- void (* MemRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Memory Rx Transfer completed callback */
- void (* ErrorCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Error callback */
- void (* AbortCpltCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Abort callback */
+ void (* MasterTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Master Tx Transfer completed callback */
+ void (* MasterRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Master Rx Transfer completed callback */
+ void (* SlaveTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Slave Tx Transfer completed callback */
+ void (* SlaveRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Slave Rx Transfer completed callback */
+ void (* ListenCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Listen Complete callback */
+ void (* MemTxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Memory Tx Transfer completed callback */
+ void (* MemRxCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Memory Rx Transfer completed callback */
+ void (* ErrorCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Error callback */
+ void (* AbortCpltCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Abort callback */
- void (* AddrCallback)(struct __I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode); /*!< I2C Slave Address Match callback */
+ void (* AddrCallback)(struct __I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode);
+ /*!< I2C Slave Address Match callback */
- void (* MspInitCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Msp Init callback */
- void (* MspDeInitCallback)(struct __I2C_HandleTypeDef *hi2c); /*!< I2C Msp DeInit callback */
+ void (* MspInitCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Msp Init callback */
+ void (* MspDeInitCallback)(struct __I2C_HandleTypeDef *hi2c);
+ /*!< I2C Msp DeInit callback */
#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
} I2C_HandleTypeDef;
@@ -259,8 +273,11 @@
/**
* @brief HAL I2C Callback pointer definition
*/
-typedef void (*pI2C_CallbackTypeDef)(I2C_HandleTypeDef *hi2c); /*!< pointer to an I2C callback function */
-typedef void (*pI2C_AddrCallbackTypeDef)(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection, uint16_t AddrMatchCode); /*!< pointer to an I2C Address Match callback function */
+typedef void (*pI2C_CallbackTypeDef)(I2C_HandleTypeDef *hi2c);
+/*!< pointer to an I2C callback function */
+typedef void (*pI2C_AddrCallbackTypeDef)(I2C_HandleTypeDef *hi2c, uint8_t TransferDirection,
+ uint16_t AddrMatchCode);
+/*!< pointer to an I2C Address Match callback function */
#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
/**
@@ -440,14 +457,14 @@
* @retval None
*/
#if (USE_HAL_I2C_REGISTER_CALLBACKS == 1)
-#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__) do{ \
- (__HANDLE__)->State = HAL_I2C_STATE_RESET; \
- (__HANDLE__)->MspInitCallback = NULL; \
- (__HANDLE__)->MspDeInitCallback = NULL; \
+#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__) do{ \
+ (__HANDLE__)->State = HAL_I2C_STATE_RESET; \
+ (__HANDLE__)->MspInitCallback = NULL; \
+ (__HANDLE__)->MspDeInitCallback = NULL; \
} while(0)
#else
#define __HAL_I2C_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_I2C_STATE_RESET)
-#endif
+#endif /* USE_HAL_I2C_REGISTER_CALLBACKS */
/** @brief Enable the specified I2C interrupt.
* @param __HANDLE__ specifies the I2C Handle.
@@ -542,26 +559,27 @@
*
* @retval None
*/
-#define __HAL_I2C_CLEAR_FLAG(__HANDLE__, __FLAG__) (((__FLAG__) == I2C_FLAG_TXE) ? ((__HANDLE__)->Instance->ISR |= (__FLAG__)) \
- : ((__HANDLE__)->Instance->ICR = (__FLAG__)))
+#define __HAL_I2C_CLEAR_FLAG(__HANDLE__, __FLAG__) (((__FLAG__) == I2C_FLAG_TXE) ? \
+ ((__HANDLE__)->Instance->ISR |= (__FLAG__)) : \
+ ((__HANDLE__)->Instance->ICR = (__FLAG__)))
/** @brief Enable the specified I2C peripheral.
* @param __HANDLE__ specifies the I2C Handle.
* @retval None
*/
-#define __HAL_I2C_ENABLE(__HANDLE__) (SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
+#define __HAL_I2C_ENABLE(__HANDLE__) (SET_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
/** @brief Disable the specified I2C peripheral.
* @param __HANDLE__ specifies the I2C Handle.
* @retval None
*/
-#define __HAL_I2C_DISABLE(__HANDLE__) (CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
+#define __HAL_I2C_DISABLE(__HANDLE__) (CLEAR_BIT((__HANDLE__)->Instance->CR1, I2C_CR1_PE))
/** @brief Generate a Non-Acknowledge I2C peripheral in Slave mode.
* @param __HANDLE__ specifies the I2C Handle.
* @retval None
*/
-#define __HAL_I2C_GENERATE_NACK(__HANDLE__) (SET_BIT((__HANDLE__)->Instance->CR2, I2C_CR2_NACK))
+#define __HAL_I2C_GENERATE_NACK(__HANDLE__) (SET_BIT((__HANDLE__)->Instance->CR2, I2C_CR2_NACK))
/**
* @}
*/
@@ -601,12 +619,14 @@
*/
/* IO operation functions ****************************************************/
/******* Blocking mode: Polling */
-HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size,
- uint32_t Timeout);
-HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size,
+HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+ uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+ uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
uint32_t Timeout);
-HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout);
-HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+ uint32_t Timeout);
HAL_StatusTypeDef HAL_I2C_Mem_Write(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
uint16_t MemAddSize, uint8_t *pData, uint16_t Size, uint32_t Timeout);
HAL_StatusTypeDef HAL_I2C_Mem_Read(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
@@ -757,10 +777,14 @@
((REQUEST) == I2C_OTHER_AND_LAST_FRAME))
#define I2C_RESET_CR2(__HANDLE__) ((__HANDLE__)->Instance->CR2 &= \
- (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_HEAD10R | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_RD_WRN)))
+ (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_HEAD10R | \
+ I2C_CR2_NBYTES | I2C_CR2_RELOAD | \
+ I2C_CR2_RD_WRN)))
-#define I2C_GET_ADDR_MATCH(__HANDLE__) ((uint16_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_ADDCODE) >> 16U))
-#define I2C_GET_DIR(__HANDLE__) ((uint8_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_DIR) >> 16U))
+#define I2C_GET_ADDR_MATCH(__HANDLE__) ((uint16_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_ADDCODE) \
+ >> 16U))
+#define I2C_GET_DIR(__HANDLE__) ((uint8_t)(((__HANDLE__)->Instance->ISR & I2C_ISR_DIR) \
+ >> 16U))
#define I2C_GET_STOP_MODE(__HANDLE__) ((__HANDLE__)->Instance->CR2 & I2C_CR2_AUTOEND)
#define I2C_GET_OWN_ADDRESS1(__HANDLE__) ((uint16_t)((__HANDLE__)->Instance->OAR1 & I2C_OAR1_OA1))
#define I2C_GET_OWN_ADDRESS2(__HANDLE__) ((uint16_t)((__HANDLE__)->Instance->OAR2 & I2C_OAR2_OA2))
@@ -772,10 +796,15 @@
(uint16_t)(0xFF00U))) >> 8U)))
#define I2C_MEM_ADD_LSB(__ADDRESS__) ((uint8_t)((uint16_t)((__ADDRESS__) & (uint16_t)(0x00FFU))))
-#define I2C_GENERATE_START(__ADDMODE__,__ADDRESS__) (((__ADDMODE__) == I2C_ADDRESSINGMODE_7BIT) ? (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | (I2C_CR2_START) | (I2C_CR2_AUTOEND)) & (~I2C_CR2_RD_WRN)) : \
- (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | (I2C_CR2_ADD10) | (I2C_CR2_START)) & (~I2C_CR2_RD_WRN)))
+#define I2C_GENERATE_START(__ADDMODE__,__ADDRESS__) (((__ADDMODE__) == I2C_ADDRESSINGMODE_7BIT) ? \
+ (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | \
+ (I2C_CR2_START) | (I2C_CR2_AUTOEND)) & \
+ (~I2C_CR2_RD_WRN)) : \
+ (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | \
+ (I2C_CR2_ADD10) | (I2C_CR2_START)) & \
+ (~I2C_CR2_RD_WRN)))
-#define I2C_CHECK_FLAG(__ISR__, __FLAG__) ((((__ISR__) & ((__FLAG__) & I2C_FLAG_MASK)) == \
+#define I2C_CHECK_FLAG(__ISR__, __FLAG__) ((((__ISR__) & ((__FLAG__) & I2C_FLAG_MASK)) == \
((__FLAG__) & I2C_FLAG_MASK)) ? SET : RESET)
#define I2C_CHECK_IT_SOURCE(__CR1__, __IT__) ((((__CR1__) & (__IT__)) == (__IT__)) ? SET : RESET)
/**
diff --git a/Inc/stm32wlxx_hal_i2c_ex.h b/Inc/stm32wlxx_hal_i2c_ex.h
index acd29b5..fd5e4b0 100644
--- a/Inc/stm32wlxx_hal_i2c_ex.h
+++ b/Inc/stm32wlxx_hal_i2c_ex.h
@@ -38,7 +38,6 @@
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
-
/** @defgroup I2CEx_Exported_Constants I2C Extended Exported Constants
* @{
*/
@@ -71,24 +70,50 @@
*/
/* Exported macro ------------------------------------------------------------*/
-/* Exported functions --------------------------------------------------------*/
+/** @defgroup I2CEx_Exported_Macros I2C Extended Exported Macros
+ * @{
+ */
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
/** @addtogroup I2CEx_Exported_Functions I2C Extended Exported Functions
* @{
*/
-/** @addtogroup I2CEx_Exported_Functions_Group1 Extended features functions
- * @brief Extended features functions
+/** @addtogroup I2CEx_Exported_Functions_Group1 Filter Mode Functions
* @{
*/
-
/* Peripheral Control functions ************************************************/
HAL_StatusTypeDef HAL_I2CEx_ConfigAnalogFilter(I2C_HandleTypeDef *hi2c, uint32_t AnalogFilter);
HAL_StatusTypeDef HAL_I2CEx_ConfigDigitalFilter(I2C_HandleTypeDef *hi2c, uint32_t DigitalFilter);
+/**
+ * @}
+ */
+
+/** @addtogroup I2CEx_Exported_Functions_Group2 WakeUp Mode Functions
+ * @{
+ */
HAL_StatusTypeDef HAL_I2CEx_EnableWakeUp(I2C_HandleTypeDef *hi2c);
HAL_StatusTypeDef HAL_I2CEx_DisableWakeUp(I2C_HandleTypeDef *hi2c);
+/**
+ * @}
+ */
+
+/** @addtogroup I2CEx_Exported_Functions_Group3 Fast Mode Plus Functions
+ * @{
+ */
void HAL_I2CEx_EnableFastModePlus(uint32_t ConfigFastModePlus);
void HAL_I2CEx_DisableFastModePlus(uint32_t ConfigFastModePlus);
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
/* Private constants ---------------------------------------------------------*/
/** @defgroup I2CEx_Private_Constants I2C Extended Private Constants
@@ -115,9 +140,6 @@
(((__CONFIG__) & (I2C_FASTMODEPLUS_I2C1)) == I2C_FASTMODEPLUS_I2C1) || \
(((__CONFIG__) & (I2C_FASTMODEPLUS_I2C2)) == I2C_FASTMODEPLUS_I2C2) || \
(((__CONFIG__) & (I2C_FASTMODEPLUS_I2C3)) == I2C_FASTMODEPLUS_I2C3))
-
-
-
/**
* @}
*/
@@ -139,14 +161,6 @@
* @}
*/
-/**
- * @}
- */
-
-/**
- * @}
- */
-
#ifdef __cplusplus
}
#endif
diff --git a/Inc/stm32wlxx_hal_irda.h b/Inc/stm32wlxx_hal_irda.h
index 627c482..8fa70cd 100644
--- a/Inc/stm32wlxx_hal_irda.h
+++ b/Inc/stm32wlxx_hal_irda.h
@@ -89,7 +89,7 @@
* 11 : Error
* b5 Peripheral initialization status
* 0 : Reset (Peripheral not initialized)
- * 1 : Init done (Peripheral not initialized. HAL IRDA Init function already called)
+ * 1 : Init done (Peripheral initialized. HAL IRDA Init function already called)
* b4-b3 (not used)
* xx : Should be set to 00
* b2 Intrinsic process state
@@ -106,7 +106,7 @@
* xx : Should be set to 00
* b5 Peripheral initialization status
* 0 : Reset (Peripheral not initialized)
- * 1 : Init done (Peripheral not initialized)
+ * 1 : Init done (Peripheral initialized)
* b4-b2 (not used)
* xxx : Should be set to 000
* b1 Rx state
diff --git a/Inc/stm32wlxx_hal_iwdg.h b/Inc/stm32wlxx_hal_iwdg.h
index 5627957..cf66672 100644
--- a/Inc/stm32wlxx_hal_iwdg.h
+++ b/Inc/stm32wlxx_hal_iwdg.h
@@ -87,7 +87,6 @@
#define IWDG_PRESCALER_64 IWDG_PR_PR_2 /*!< IWDG prescaler set to 64 */
#define IWDG_PRESCALER_128 (IWDG_PR_PR_2 | IWDG_PR_PR_0) /*!< IWDG prescaler set to 128 */
#define IWDG_PRESCALER_256 (IWDG_PR_PR_2 | IWDG_PR_PR_1) /*!< IWDG prescaler set to 256 */
-
/**
* @}
*/
@@ -100,7 +99,6 @@
* @}
*/
-
/**
* @}
*/
@@ -138,7 +136,7 @@
* @{
*/
/* Initialization/Start functions ********************************************/
-HAL_StatusTypeDef HAL_IWDG_Init(IWDG_HandleTypeDef *hiwdg);
+HAL_StatusTypeDef HAL_IWDG_Init(IWDG_HandleTypeDef *hiwdg);
/**
* @}
*/
@@ -147,7 +145,7 @@
* @{
*/
/* I/O operation functions ****************************************************/
-HAL_StatusTypeDef HAL_IWDG_Refresh(IWDG_HandleTypeDef *hiwdg);
+HAL_StatusTypeDef HAL_IWDG_Refresh(IWDG_HandleTypeDef *hiwdg);
/**
* @}
*/
diff --git a/Inc/stm32wlxx_hal_rcc.h b/Inc/stm32wlxx_hal_rcc.h
index 5d26e16..eb82375 100644
--- a/Inc/stm32wlxx_hal_rcc.h
+++ b/Inc/stm32wlxx_hal_rcc.h
@@ -51,6 +51,9 @@
#define RCC_FLAG_MASK 0x1FU
+/* Defines Oscillator Masks */
+#define RCC_OSCILLATORTYPE_ALL (RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_MSI | RCC_OSCILLATORTYPE_LSI | RCC_OSCILLATORTYPE_LSE) /*!< All Oscillator to configure */
+
/** @defgroup RCC_Timeout_Value Timeout Values
* @{
*/
@@ -61,6 +64,23 @@
* @}
*/
+/** @defgroup RCC_Reset_Flag Reset Flag
+ * @{
+ */
+#define RCC_RESET_FLAG_OBL RCC_CSR_OBLRSTF /*!< Option Byte Loader reset flag */
+#define RCC_RESET_FLAG_PIN RCC_CSR_PINRSTF /*!< PIN reset flag */
+#define RCC_RESET_FLAG_PWR RCC_CSR_BORRSTF /*!< BOR or POR/PDR reset flag */
+#define RCC_RESET_FLAG_SW RCC_CSR_SFTRSTF /*!< Software Reset flag */
+#define RCC_RESET_FLAG_IWDG RCC_CSR_IWDGRSTF /*!< Independent Watchdog reset flag */
+#define RCC_RESET_FLAG_WWDG RCC_CSR_WWDGRSTF /*!< Window watchdog reset flag */
+#define RCC_RESET_FLAG_LPWR RCC_CSR_LPWRRSTF /*!< Low power reset flag */
+#define RCC_RESET_FLAG_ALL (RCC_RESET_FLAG_OBL | RCC_RESET_FLAG_PIN | RCC_RESET_FLAG_PWR | \
+ RCC_RESET_FLAG_SW | RCC_RESET_FLAG_IWDG | RCC_RESET_FLAG_WWDG | \
+ RCC_RESET_FLAG_LPWR)
+/**
+ * @}
+ */
+
/**
* @}
*/
@@ -70,13 +90,8 @@
* @{
*/
-#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) \
- (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \
- (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \
- (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \
- (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI) || \
- (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \
- (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE))
+#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \
+ (((__OSCILLATOR__) & ~RCC_OSCILLATORTYPE_ALL) == 0x00U))
#define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \
@@ -2360,6 +2375,7 @@
/* User Callbacks in non blocking mode (IT mode) */
void HAL_RCC_CSSCallback(void);
+uint32_t HAL_RCC_GetResetSource(void);
/**
* @}
*/
diff --git a/Inc/stm32wlxx_hal_rcc_ex.h b/Inc/stm32wlxx_hal_rcc_ex.h
index 7647347..d14a81e 100644
--- a/Inc/stm32wlxx_hal_rcc_ex.h
+++ b/Inc/stm32wlxx_hal_rcc_ex.h
@@ -38,6 +38,19 @@
* @{
*/
/* Private constants ---------------------------------------------------------*/
+/** @addtogroup RCCEx_Private_Constants
+ * @{
+ */
+/* Define used for IS_RCC_* macros below */
+#define RCC_PERIPHCLOCK_ALL (RCC_PERIPHCLK_USART1 | RCC_PERIPHCLK_USART2 | RCC_PERIPHCLK_I2S2 | \
+ RCC_PERIPHCLK_LPUART1 | RCC_PERIPHCLK_I2C1 | RCC_PERIPHCLK_I2C2 | \
+ RCC_PERIPHCLK_I2C3 | RCC_PERIPHCLK_LPTIM1 | RCC_PERIPHCLK_LPTIM2 | \
+ RCC_PERIPHCLK_LPTIM3 | RCC_PERIPHCLK_ADC | RCC_PERIPHCLK_RNG | \
+ RCC_PERIPHCLK_RTC )
+/**
+ * @}
+ */
+
/* Private macros ------------------------------------------------------------*/
/** @addtogroup RCCEx_Private_Macros
* @{
@@ -46,19 +59,8 @@
#define IS_RCC_LSCOSOURCE(__SOURCE__) (((__SOURCE__) == RCC_LSCOSOURCE_LSI) || \
((__SOURCE__) == RCC_LSCOSOURCE_LSE))
-#define IS_RCC_PERIPHCLOCK(__SELECTION__) ((((__SELECTION__) & RCC_PERIPHCLK_USART1) == RCC_PERIPHCLK_USART1) || \
- (((__SELECTION__) & RCC_PERIPHCLK_USART2) == RCC_PERIPHCLK_USART2) || \
- (((__SELECTION__) & RCC_PERIPHCLK_LPUART1) == RCC_PERIPHCLK_LPUART1) || \
- (((__SELECTION__) & RCC_PERIPHCLK_I2S2) == RCC_PERIPHCLK_I2S2) || \
- (((__SELECTION__) & RCC_PERIPHCLK_I2C1) == RCC_PERIPHCLK_I2C1) || \
- (((__SELECTION__) & RCC_PERIPHCLK_I2C2) == RCC_PERIPHCLK_I2C2) || \
- (((__SELECTION__) & RCC_PERIPHCLK_I2C3) == RCC_PERIPHCLK_I2C3) || \
- (((__SELECTION__) & RCC_PERIPHCLK_LPTIM1) == RCC_PERIPHCLK_LPTIM1) || \
- (((__SELECTION__) & RCC_PERIPHCLK_LPTIM2) == RCC_PERIPHCLK_LPTIM2) || \
- (((__SELECTION__) & RCC_PERIPHCLK_LPTIM3) == RCC_PERIPHCLK_LPTIM3) || \
- (((__SELECTION__) & RCC_PERIPHCLK_RNG) == RCC_PERIPHCLK_RNG) || \
- (((__SELECTION__) & RCC_PERIPHCLK_ADC) == RCC_PERIPHCLK_ADC) || \
- (((__SELECTION__) & RCC_PERIPHCLK_RTC) == RCC_PERIPHCLK_RTC))
+#define IS_RCC_PERIPHCLOCK(__SELECTION__) ((((__SELECTION__) & RCC_PERIPHCLOCK_ALL) != 0x00u) && \
+ (((__SELECTION__) & ~RCC_PERIPHCLOCK_ALL) == 0x00u))
#define IS_RCC_USART1CLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_USART1CLKSOURCE_PCLK2) || \
((__SOURCE__) == RCC_USART1CLKSOURCE_SYSCLK) || \
diff --git a/Inc/stm32wlxx_hal_rng.h b/Inc/stm32wlxx_hal_rng.h
index 7a0c755..cc62fd8 100644
--- a/Inc/stm32wlxx_hal_rng.h
+++ b/Inc/stm32wlxx_hal_rng.h
@@ -363,15 +363,14 @@
* @}
*/
-/* Private functions----------------------------------------------------------*/
-/** @defgroup RNG_Private_Functions RNG Private Functions
+/* Private functions ---------------------------------------------------------*/
+/** @defgroup RNG_Private_Functions RNG Private functions
* @{
*/
HAL_StatusTypeDef RNG_RecoverSeedError(RNG_HandleTypeDef *hrng);
/**
* @}
*/
-
/**
* @}
*/
diff --git a/Inc/stm32wlxx_hal_rng_ex.h b/Inc/stm32wlxx_hal_rng_ex.h
index f93507c..c1792c7 100644
--- a/Inc/stm32wlxx_hal_rng_ex.h
+++ b/Inc/stm32wlxx_hal_rng_ex.h
@@ -35,19 +35,19 @@
#if defined(RNG)
#if defined(RNG_CR_CONDRST)
-/** @defgroup RNGEx RNGEx
+/** @defgroup RNG_Ex RNG_Ex
* @brief RNG Extension HAL module driver
* @{
*/
/* Exported types ------------------------------------------------------------*/
-/** @defgroup RNGEx_Exported_Types RNGEx Exported Types
- * @brief RNGEx Exported types
+/** @defgroup RNG_Ex_Exported_Types RNG_Ex Exported Types
+ * @brief RNG_Ex Exported types
* @{
*/
/**
- * @brief RNGEX Configuration Structure definition
+ * @brief RNG_Ex Configuration Structure definition
*/
typedef struct
@@ -56,9 +56,9 @@
uint32_t Config2; /*!< Config2 must be a value between 0 and 0x7 */
uint32_t Config3; /*!< Config3 must be a value between 0 and 0xF */
uint32_t ClockDivider; /*!< Clock Divider factor.This parameter can
- be a value of @ref RNGEX_Clock_Divider_Factor */
+ be a value of @ref RNG_Ex_Clock_Divider_Factor */
uint32_t NistCompliance; /*!< NIST compliance.This parameter can be a
- value of @ref RNGEX_NIST_Compliance */
+ value of @ref RNG_Ex_NIST_Compliance */
} RNG_ConfigTypeDef;
/**
@@ -66,11 +66,11 @@
*/
/* Exported constants --------------------------------------------------------*/
-/** @defgroup RNGEX_Exported_Constants RNGEX Exported Constants
+/** @defgroup RNG_Ex_Exported_Constants RNG_Ex Exported Constants
* @{
*/
-/** @defgroup RNGEX_Clock_Divider_Factor Value used to configure an internal
+/** @defgroup RNG_Ex_Clock_Divider_Factor Value used to configure an internal
* programmable divider acting on the incoming RNG clock
* @{
*/
@@ -109,7 +109,7 @@
* @}
*/
-/** @defgroup RNGEX_NIST_Compliance NIST Compliance configuration
+/** @defgroup RNG_Ex_NIST_Compliance NIST Compliance configuration
* @{
*/
#define RNG_NIST_COMPLIANT (0x00000000UL) /*!< NIST compliant configuration*/
@@ -124,7 +124,7 @@
*/
/* Private types -------------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Types RNGEx Private Types
+/** @defgroup RNG_Ex_Private_Types RNG_Ex Private Types
* @{
*/
@@ -133,7 +133,7 @@
*/
/* Private variables ---------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Variables RNGEx Private Variables
+/** @defgroup RNG_Ex_Private_Variables RNG_Ex Private Variables
* @{
*/
@@ -142,7 +142,7 @@
*/
/* Private constants ---------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Constants RNGEx Private Constants
+/** @defgroup RNG_Ex_Private_Constants RNG_Ex Private Constants
* @{
*/
@@ -151,7 +151,7 @@
*/
/* Private macros ------------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Macros RNGEx Private Macros
+/** @defgroup RNG_Ex_Private_Macros RNG_Ex Private Macros
* @{
*/
@@ -188,7 +188,7 @@
*/
/* Private functions ---------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Functions RNGEx Private Functions
+/** @defgroup RNG_Ex_Private_Functions RNG_Ex Private Functions
* @{
*/
@@ -197,11 +197,11 @@
*/
/* Exported functions --------------------------------------------------------*/
-/** @defgroup RNGEx_Exported_Functions RNGEx Exported Functions
+/** @defgroup RNG_Ex_Exported_Functions RNG_Ex Exported Functions
* @{
*/
-/** @addtogroup RNGEx_Exported_Functions_Group1
+/** @addtogroup RNG_Ex_Exported_Functions_Group1
* @{
*/
HAL_StatusTypeDef HAL_RNGEx_SetConfig(RNG_HandleTypeDef *hrng, RNG_ConfigTypeDef *pConf);
@@ -212,7 +212,7 @@
* @}
*/
-/** @addtogroup RNGEx_Exported_Functions_Group2
+/** @addtogroup RNG_Ex_Exported_Functions_Group2
* @{
*/
HAL_StatusTypeDef HAL_RNGEx_RecoverSeedError(RNG_HandleTypeDef *hrng);
@@ -245,6 +245,6 @@
#endif
-#endif /* STM32WLxx_HAL_RNGEX_H */
+#endif /* STM32WLxx_HAL_RNG_EX_H */
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/Inc/stm32wlxx_hal_rtc_ex.h b/Inc/stm32wlxx_hal_rtc_ex.h
index f6abf90..6906e9f 100644
--- a/Inc/stm32wlxx_hal_rtc_ex.h
+++ b/Inc/stm32wlxx_hal_rtc_ex.h
@@ -322,13 +322,13 @@
#define RTC_IT_TAMP_1 TAMP_IER_TAMP1IE /*!< Tamper 1 Interrupt */
#define RTC_IT_TAMP_2 TAMP_IER_TAMP2IE /*!< Tamper 2 Interrupt */
#define RTC_IT_TAMP_3 TAMP_IER_TAMP3IE /*!< Tamper 3 Interrupt */
-#define RTC_IT_TAMP_ALL (TAMP_IER_TAMP1IE | TAMP_IER_TAMP2IE | TAMP_IER_TAMP3IE)
+#define RTC_IT_TAMP_ALL (TAMP_IER_TAMP1IE | TAMP_IER_TAMP2IE | TAMP_IER_TAMP3IE)
#define RTC_IT_INT_TAMP_3 TAMP_IER_ITAMP3IE
#define RTC_IT_INT_TAMP_5 TAMP_IER_ITAMP5IE
#define RTC_IT_INT_TAMP_6 TAMP_IER_ITAMP6IE
#define RTC_IT_INT_TAMP_8 TAMP_IER_ITAMP8IE
-#define RTC_IT_INT_TAMP_ALL (TAMP_IT_INT_TAMP3 | TAMP_IT_INT_TAMP5 | TAMP_IT_INT_TAMP6 | TAMP_IT_INT_TAMP8)
+#define RTC_IT_INT_TAMP_ALL (TAMP_IER_ITAMP3IE | TAMP_IER_ITAMP5IE | TAMP_IER_ITAMP6IE | TAMP_IER_ITAMP8IE)
/**
* @}
*/
@@ -339,7 +339,7 @@
#define RTC_FLAG_TAMP_1 TAMP_SR_TAMP1F
#define RTC_FLAG_TAMP_2 TAMP_SR_TAMP2F
#define RTC_FLAG_TAMP_3 TAMP_SR_TAMP3F
-#define RTC_FLAG_TAMP_ALL (RTC_FLAG_TAMP1 | RTC_FLAG_TAMP2 | RTC_FLAG_TAMP3 )
+#define RTC_FLAG_TAMP_ALL (RTC_FLAG_TAMP1 | RTC_FLAG_TAMP2 | RTC_FLAG_TAMP3 )
#define RTC_FLAG_INT_TAMP_3 TAMP_SR_ITAMP3F
@@ -727,13 +727,13 @@
#if defined(CORE_CM0PLUS)
#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
-#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
-#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
+#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
+#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
#else
#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
-#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
-#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
+#define __HAL_RTC_TIMESTAMP_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TIMESTAMP_EVENT)
+#define __HAL_RTC_TIMESTAMP_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TIMESTAMP_EVENT))
#endif
/**
@@ -866,9 +866,14 @@
* @arg RTC_TAMPER_1: Tamper1
* @arg RTC_TAMPER_2: Tamper2
* @arg RTC_TAMPER_3: Tamper3
+ * @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
+ * @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
+ * @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
+ * @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
+ * @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
-#define __HAL_RTC_TAMPER_ENABLE(__HANDLE__, __TAMPER__) ((TAMP->CR1 |= (__TAMPER__))
+#define __HAL_RTC_TAMPER_ENABLE(__HANDLE__, __TAMPER__) (TAMP->CR1 |= (__TAMPER__))
/**
* @brief Disable the TAMP Tamper input detection.
@@ -879,8 +884,13 @@
* @arg RTC_TAMPER_1: Tamper1
* @arg RTC_TAMPER_2: Tamper2
* @arg RTC_TAMPER_3: Tamper3
+ * @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
+ * @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
+ * @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
+ * @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
+ * @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
*/
-#define __HAL_RTC_TAMPER_DISABLE(__HANDLE__, __TAMPER__) ((TAMP->CR1 &= ~(__TAMPER__))
+#define __HAL_RTC_TAMPER_DISABLE(__HANDLE__, __TAMPER__) (TAMP->CR1 &= ~(__TAMPER__))
/**************************************************************************************************/
@@ -893,9 +903,14 @@
* @arg RTC_IT_TAMP_1: Tamper1 interrupt
* @arg RTC_IT_TAMP_2: Tamper2 interrupt
* @arg RTC_IT_TAMP_3: Tamper3 interrupt
+ * @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
+ * @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
+ * @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
+ * @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
+ * @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
-#define __HAL_RTC_TAMPER_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((TAMP->IER |= (__INTERRUPT__))
+#define __HAL_RTC_TAMPER_ENABLE_IT(__HANDLE__, __INTERRUPT__) (TAMP->IER |= (__INTERRUPT__))
/**
* @brief Disable the TAMP Tamper interrupt.
@@ -906,10 +921,14 @@
* @arg RTC_IT_TAMP_1: Tamper1 interrupt
* @arg RTC_IT_TAMP_2: Tamper2 interrupt
* @arg RTC_IT_TAMP_3: Tamper3 interrupt
-
+ * @arg RTC_IT_INT_TAMP_ALL: All Internal Tamper interrupts
+ * @arg RTC_IT_INT_TAMP_3: Internal Tamper3 interrupt
+ * @arg RTC_IT_INT_TAMP_5: Internal Tamper5 interrupt
+ * @arg RTC_IT_INT_TAMP_6: Internal Tamper6 interrupt
+ * @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
-#define __HAL_RTC_TAMPER_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((TAMP->IER &= ~(__INTERRUPT__))
+#define __HAL_RTC_TAMPER_DISABLE_IT(__HANDLE__, __INTERRUPT__) (TAMP->IER &= ~(__INTERRUPT__))
/**************************************************************************************************/
@@ -929,7 +948,7 @@
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
-#define __HAL_RTC_TAMPER_GET_IT(__HANDLE__, __INTERRUPT__) (((((TAMP->MISR) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
+#define __HAL_RTC_TAMPER_GET_IT(__HANDLE__, __INTERRUPT__) ((((TAMP->MISR) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
/**
@@ -948,7 +967,7 @@
* @arg RTC_IT_INT_TAMP_8: Internal Tamper8 interrupt
* @retval None
*/
-#define __HAL_RTC_TAMPER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) (((((TAMP->IER) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
+#define __HAL_RTC_TAMPER_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((TAMP->IER) & (__INTERRUPT__)) != 0U) ? 1UL : 0UL)
/**
@@ -990,13 +1009,13 @@
#if defined(CORE_CM0PLUS)
#define __HAL_RTC_TAMPER_EXTI_ENABLE_IT() (EXTI->C2IMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
#define __HAL_RTC_TAMPER_EXTI_DISABLE_IT() (EXTI->C2IMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
-#define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
-#define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
+#define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->C2EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
+#define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->C2EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
#else
#define __HAL_RTC_TAMPER_EXTI_ENABLE_IT() (EXTI->IMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
#define __HAL_RTC_TAMPER_EXTI_DISABLE_IT() (EXTI->IMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
-#define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
-#define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
+#define __HAL_RTC_TAMPER_EXTI_ENABLE_EVENT() (EXTI->EMR1 |= RTC_EXTI_LINE_TAMPER_EVENT)
+#define __HAL_RTC_TAMPER_EXTI_DISABLE_EVENT() (EXTI->EMR1 &= ~(RTC_EXTI_LINE_TAMPER_EVENT))
#endif
/**
@@ -1037,7 +1056,7 @@
* @arg @ref RTC_IT_SSRU SSRU interrupt
* @retval None
*/
-#define __HAL_RTC_SSRU_GET_IT(__HANDLE__, __INTERRUPT__) ((((RTC->MISR) & ((__INTERRUPT__) >> 1) != 0U) ? 1U : 0U)
+#define __HAL_RTC_SSRU_GET_IT(__HANDLE__, __INTERRUPT__) (((RTC->MISR) & ((__INTERRUPT__) >> 1) != 0U) ? 1U : 0U)
/**
* @brief Check whether the specified RTC Wake Up timer interrupt has been enabled or not.
* @param __HANDLE__ specifies the RTC handle.
diff --git a/Inc/stm32wlxx_hal_smartcard.h b/Inc/stm32wlxx_hal_smartcard.h
index cb80428..4d20df4 100644
--- a/Inc/stm32wlxx_hal_smartcard.h
+++ b/Inc/stm32wlxx_hal_smartcard.h
@@ -159,7 +159,7 @@
* 11 : Error
* b5 Peripheral initialization status
* 0 : Reset (Peripheral not initialized)
- * 1 : Init done (Peripheral not initialized. HAL SMARTCARD Init function already called)
+ * 1 : Init done (Peripheral initialized. HAL SMARTCARD Init function already called)
* b4-b3 (not used)
* xx : Should be set to 00
* b2 Intrinsic process state
@@ -176,7 +176,7 @@
* xx : Should be set to 00
* b5 Peripheral initialization status
* 0 : Reset (Peripheral not initialized)
- * 1 : Init done (Peripheral not initialized)
+ * 1 : Init done (Peripheral initialized)
* b4-b2 (not used)
* xxx : Should be set to 000
* b1 Rx state
diff --git a/Inc/stm32wlxx_hal_smbus.h b/Inc/stm32wlxx_hal_smbus.h
index 51bd713..8db5112 100644
--- a/Inc/stm32wlxx_hal_smbus.h
+++ b/Inc/stm32wlxx_hal_smbus.h
@@ -27,6 +27,7 @@
/* Includes ------------------------------------------------------------------*/
#include "stm32wlxx_hal_def.h"
+#include "stm32wlxx_hal_smbus_ex.h"
/** @addtogroup STM32WLxx_HAL_Driver
* @{
@@ -48,42 +49,43 @@
typedef struct
{
uint32_t Timing; /*!< Specifies the SMBUS_TIMINGR_register value.
- This parameter calculated by referring to SMBUS initialization
- section in Reference manual */
+ This parameter calculated by referring to SMBUS initialization section
+ in Reference manual */
uint32_t AnalogFilter; /*!< Specifies if Analog Filter is enable or not.
- This parameter can be a value of @ref SMBUS_Analog_Filter */
+ This parameter can be a value of @ref SMBUS_Analog_Filter */
uint32_t OwnAddress1; /*!< Specifies the first device own address.
- This parameter can be a 7-bit or 10-bit address. */
+ This parameter can be a 7-bit or 10-bit address. */
uint32_t AddressingMode; /*!< Specifies if 7-bit or 10-bit addressing mode for master is selected.
- This parameter can be a value of @ref SMBUS_addressing_mode */
+ This parameter can be a value of @ref SMBUS_addressing_mode */
uint32_t DualAddressMode; /*!< Specifies if dual addressing mode is selected.
- This parameter can be a value of @ref SMBUS_dual_addressing_mode */
+ This parameter can be a value of @ref SMBUS_dual_addressing_mode */
uint32_t OwnAddress2; /*!< Specifies the second device own address if dual addressing mode is selected
- This parameter can be a 7-bit address. */
+ This parameter can be a 7-bit address. */
- uint32_t OwnAddress2Masks; /*!< Specifies the acknowledge mask address second device own address if dual addressing mode is selected
- This parameter can be a value of @ref SMBUS_own_address2_masks. */
+ uint32_t OwnAddress2Masks; /*!< Specifies the acknowledge mask address second device own address
+ if dual addressing mode is selected
+ This parameter can be a value of @ref SMBUS_own_address2_masks. */
uint32_t GeneralCallMode; /*!< Specifies if general call mode is selected.
- This parameter can be a value of @ref SMBUS_general_call_addressing_mode. */
+ This parameter can be a value of @ref SMBUS_general_call_addressing_mode. */
uint32_t NoStretchMode; /*!< Specifies if nostretch mode is selected.
- This parameter can be a value of @ref SMBUS_nostretch_mode */
+ This parameter can be a value of @ref SMBUS_nostretch_mode */
uint32_t PacketErrorCheckMode; /*!< Specifies if Packet Error Check mode is selected.
- This parameter can be a value of @ref SMBUS_packet_error_check_mode */
+ This parameter can be a value of @ref SMBUS_packet_error_check_mode */
uint32_t PeripheralMode; /*!< Specifies which mode of Periphal is selected.
- This parameter can be a value of @ref SMBUS_peripheral_mode */
+ This parameter can be a value of @ref SMBUS_peripheral_mode */
uint32_t SMBusTimeout; /*!< Specifies the content of the 32 Bits SMBUS_TIMEOUT_register value.
- (Enable bits and different timeout values)
- This parameter calculated by referring to SMBUS initialization
- section in Reference manual */
+ (Enable bits and different timeout values)
+ This parameter calculated by referring to SMBUS initialization section
+ in Reference manual */
} SMBUS_InitTypeDef;
/**
* @}
@@ -102,7 +104,7 @@
#define HAL_SMBUS_STATE_SLAVE_BUSY_RX (0x00000042U) /*!< Slave Data Reception process is ongoing */
#define HAL_SMBUS_STATE_TIMEOUT (0x00000003U) /*!< Timeout state */
#define HAL_SMBUS_STATE_ERROR (0x00000004U) /*!< Reception process is ongoing */
-#define HAL_SMBUS_STATE_LISTEN (0x00000008U) /*!< Address Listen Mode is ongoing */
+#define HAL_SMBUS_STATE_LISTEN (0x00000008U) /*!< Address Listen Mode is ongoing */
/**
* @}
*/
@@ -121,7 +123,7 @@
#define HAL_SMBUS_ERROR_ALERT (0x00000040U) /*!< Alert error */
#define HAL_SMBUS_ERROR_PECERR (0x00000080U) /*!< PEC error */
#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
-#define HAL_SMBUS_ERROR_INVALID_CALLBACK (0x00000100U) /*!< Invalid Callback error */
+#define HAL_SMBUS_ERROR_INVALID_CALLBACK (0x00000100U) /*!< Invalid Callback error */
#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
#define HAL_SMBUS_ERROR_INVALID_PARAM (0x00000200U) /*!< Invalid Parameters error */
/**
@@ -159,17 +161,26 @@
__IO uint32_t ErrorCode; /*!< SMBUS Error code */
#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
- void (* MasterTxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Master Tx Transfer completed callback */
- void (* MasterRxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Master Rx Transfer completed callback */
- void (* SlaveTxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Slave Tx Transfer completed callback */
- void (* SlaveRxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Slave Rx Transfer completed callback */
- void (* ListenCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Listen Complete callback */
- void (* ErrorCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Error callback */
+ void (* MasterTxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Master Tx Transfer completed callback */
+ void (* MasterRxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Master Rx Transfer completed callback */
+ void (* SlaveTxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Slave Tx Transfer completed callback */
+ void (* SlaveRxCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Slave Rx Transfer completed callback */
+ void (* ListenCpltCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Listen Complete callback */
+ void (* ErrorCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Error callback */
- void (* AddrCallback)(struct __SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode); /*!< SMBUS Slave Address Match callback */
+ void (* AddrCallback)(struct __SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode);
+ /*!< SMBUS Slave Address Match callback */
- void (* MspInitCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Msp Init callback */
- void (* MspDeInitCallback)(struct __SMBUS_HandleTypeDef *hsmbus); /*!< SMBUS Msp DeInit callback */
+ void (* MspInitCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Msp Init callback */
+ void (* MspDeInitCallback)(struct __SMBUS_HandleTypeDef *hsmbus);
+ /*!< SMBUS Msp DeInit callback */
#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
} SMBUS_HandleTypeDef;
@@ -195,8 +206,11 @@
/**
* @brief HAL SMBUS Callback pointer definition
*/
-typedef void (*pSMBUS_CallbackTypeDef)(SMBUS_HandleTypeDef *hsmbus); /*!< pointer to an SMBUS callback function */
-typedef void (*pSMBUS_AddrCallbackTypeDef)(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode); /*!< pointer to an SMBUS Address Match callback function */
+typedef void (*pSMBUS_CallbackTypeDef)(SMBUS_HandleTypeDef *hsmbus);
+/*!< pointer to an SMBUS callback function */
+typedef void (*pSMBUS_AddrCallbackTypeDef)(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection,
+ uint16_t AddrMatchCode);
+/*!< pointer to an SMBUS Address Match callback function */
#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
/**
@@ -358,9 +372,10 @@
#define SMBUS_IT_ADDRI I2C_CR1_ADDRIE
#define SMBUS_IT_RXI I2C_CR1_RXIE
#define SMBUS_IT_TXI I2C_CR1_TXIE
-#define SMBUS_IT_TX (SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | \
- SMBUS_IT_TXI)
-#define SMBUS_IT_RX (SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_NACKI | SMBUS_IT_RXI)
+#define SMBUS_IT_TX (SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_STOPI | \
+ SMBUS_IT_NACKI | SMBUS_IT_TXI)
+#define SMBUS_IT_RX (SMBUS_IT_ERRI | SMBUS_IT_TCI | SMBUS_IT_NACKI | \
+ SMBUS_IT_RXI)
#define SMBUS_IT_ALERT (SMBUS_IT_ERRI)
#define SMBUS_IT_ADDR (SMBUS_IT_ADDRI | SMBUS_IT_STOPI | SMBUS_IT_NACKI)
/**
@@ -408,14 +423,14 @@
* @retval None
*/
#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
-#define __HAL_SMBUS_RESET_HANDLE_STATE(__HANDLE__) do{ \
- (__HANDLE__)->State = HAL_SMBUS_STATE_RESET; \
+#define __HAL_SMBUS_RESET_HANDLE_STATE(__HANDLE__) do{ \
+ (__HANDLE__)->State = HAL_SMBUS_STATE_RESET; \
(__HANDLE__)->MspInitCallback = NULL; \
(__HANDLE__)->MspDeInitCallback = NULL; \
} while(0)
#else
#define __HAL_SMBUS_RESET_HANDLE_STATE(__HANDLE__) ((__HANDLE__)->State = HAL_SMBUS_STATE_RESET)
-#endif
+#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
/** @brief Enable the specified SMBUS interrupts.
* @param __HANDLE__ specifies the SMBUS Handle.
@@ -491,7 +506,8 @@
*/
#define SMBUS_FLAG_MASK (0x0001FFFFU)
#define __HAL_SMBUS_GET_FLAG(__HANDLE__, __FLAG__) \
- (((((__HANDLE__)->Instance->ISR) & ((__FLAG__) & SMBUS_FLAG_MASK)) == ((__FLAG__) & SMBUS_FLAG_MASK)) ? SET : RESET)
+ (((((__HANDLE__)->Instance->ISR) & ((__FLAG__) & SMBUS_FLAG_MASK)) == \
+ ((__FLAG__) & SMBUS_FLAG_MASK)) ? SET : RESET)
/** @brief Clear the SMBUS pending flags which are cleared by writing 1 in a specific bit.
* @param __HANDLE__ specifies the SMBUS Handle.
@@ -574,43 +590,52 @@
((MODE) == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE) || \
((MODE) == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE_ARP))
-#define IS_SMBUS_TRANSFER_MODE(MODE) (((MODE) == SMBUS_RELOAD_MODE) || \
- ((MODE) == SMBUS_AUTOEND_MODE) || \
- ((MODE) == SMBUS_SOFTEND_MODE) || \
- ((MODE) == SMBUS_SENDPEC_MODE) || \
- ((MODE) == (SMBUS_RELOAD_MODE | SMBUS_SENDPEC_MODE)) || \
- ((MODE) == (SMBUS_AUTOEND_MODE | SMBUS_SENDPEC_MODE)) || \
- ((MODE) == (SMBUS_AUTOEND_MODE | SMBUS_RELOAD_MODE)) || \
- ((MODE) == (SMBUS_AUTOEND_MODE | SMBUS_SENDPEC_MODE | SMBUS_RELOAD_MODE )))
+#define IS_SMBUS_TRANSFER_MODE(MODE) (((MODE) == SMBUS_RELOAD_MODE) || \
+ ((MODE) == SMBUS_AUTOEND_MODE) || \
+ ((MODE) == SMBUS_SOFTEND_MODE) || \
+ ((MODE) == SMBUS_SENDPEC_MODE) || \
+ ((MODE) == (SMBUS_RELOAD_MODE | SMBUS_SENDPEC_MODE)) || \
+ ((MODE) == (SMBUS_AUTOEND_MODE | SMBUS_SENDPEC_MODE)) || \
+ ((MODE) == (SMBUS_AUTOEND_MODE | SMBUS_RELOAD_MODE)) || \
+ ((MODE) == (SMBUS_AUTOEND_MODE | SMBUS_SENDPEC_MODE | \
+ SMBUS_RELOAD_MODE )))
#define IS_SMBUS_TRANSFER_REQUEST(REQUEST) (((REQUEST) == SMBUS_GENERATE_STOP) || \
- ((REQUEST) == SMBUS_GENERATE_START_READ) || \
- ((REQUEST) == SMBUS_GENERATE_START_WRITE) || \
+ ((REQUEST) == SMBUS_GENERATE_START_READ) || \
+ ((REQUEST) == SMBUS_GENERATE_START_WRITE) || \
((REQUEST) == SMBUS_NO_STARTSTOP))
-#define IS_SMBUS_TRANSFER_OPTIONS_REQUEST(REQUEST) (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) || \
- ((REQUEST) == SMBUS_FIRST_FRAME) || \
- ((REQUEST) == SMBUS_NEXT_FRAME) || \
- ((REQUEST) == SMBUS_FIRST_AND_LAST_FRAME_NO_PEC) || \
- ((REQUEST) == SMBUS_LAST_FRAME_NO_PEC) || \
- ((REQUEST) == SMBUS_FIRST_FRAME_WITH_PEC) || \
- ((REQUEST) == SMBUS_FIRST_AND_LAST_FRAME_WITH_PEC) || \
- ((REQUEST) == SMBUS_LAST_FRAME_WITH_PEC))
+#define IS_SMBUS_TRANSFER_OPTIONS_REQUEST(REQUEST) (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) || \
+ ((REQUEST) == SMBUS_FIRST_FRAME) || \
+ ((REQUEST) == SMBUS_NEXT_FRAME) || \
+ ((REQUEST) == SMBUS_FIRST_AND_LAST_FRAME_NO_PEC) || \
+ ((REQUEST) == SMBUS_LAST_FRAME_NO_PEC) || \
+ ((REQUEST) == SMBUS_FIRST_FRAME_WITH_PEC) || \
+ ((REQUEST) == SMBUS_FIRST_AND_LAST_FRAME_WITH_PEC) || \
+ ((REQUEST) == SMBUS_LAST_FRAME_WITH_PEC))
-#define IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) (((REQUEST) == SMBUS_OTHER_FRAME_NO_PEC) || \
- ((REQUEST) == SMBUS_OTHER_AND_LAST_FRAME_NO_PEC) || \
- ((REQUEST) == SMBUS_OTHER_FRAME_WITH_PEC) || \
+#define IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(REQUEST) (((REQUEST) == SMBUS_OTHER_FRAME_NO_PEC) || \
+ ((REQUEST) == SMBUS_OTHER_AND_LAST_FRAME_NO_PEC) || \
+ ((REQUEST) == SMBUS_OTHER_FRAME_WITH_PEC) || \
((REQUEST) == SMBUS_OTHER_AND_LAST_FRAME_WITH_PEC))
-#define SMBUS_RESET_CR1(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= \
- (uint32_t)~((uint32_t)(I2C_CR1_SMBHEN | I2C_CR1_SMBDEN | I2C_CR1_PECEN)))
-#define SMBUS_RESET_CR2(__HANDLE__) ((__HANDLE__)->Instance->CR2 &= \
- (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_HEAD10R | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_RD_WRN)))
+#define SMBUS_RESET_CR1(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= \
+ (uint32_t)~((uint32_t)(I2C_CR1_SMBHEN | I2C_CR1_SMBDEN | \
+ I2C_CR1_PECEN)))
+#define SMBUS_RESET_CR2(__HANDLE__) ((__HANDLE__)->Instance->CR2 &= \
+ (uint32_t)~((uint32_t)(I2C_CR2_SADD | I2C_CR2_HEAD10R | \
+ I2C_CR2_NBYTES | I2C_CR2_RELOAD | \
+ I2C_CR2_RD_WRN)))
-#define SMBUS_GENERATE_START(__ADDMODE__,__ADDRESS__) (((__ADDMODE__) == SMBUS_ADDRESSINGMODE_7BIT) ? (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | (I2C_CR2_START) | (I2C_CR2_AUTOEND)) & (~I2C_CR2_RD_WRN)) : \
- (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | (I2C_CR2_ADD10) | (I2C_CR2_START)) & (~I2C_CR2_RD_WRN)))
+#define SMBUS_GENERATE_START(__ADDMODE__,__ADDRESS__) (((__ADDMODE__) == SMBUS_ADDRESSINGMODE_7BIT) ? \
+ (uint32_t)((((uint32_t)(__ADDRESS__) & (I2C_CR2_SADD)) | \
+ (I2C_CR2_START) | (I2C_CR2_AUTOEND)) & \
+ (~I2C_CR2_RD_WRN)) : \
+ (uint32_t)((((uint32_t)(__ADDRESS__) & \
+ (I2C_CR2_SADD)) | (I2C_CR2_ADD10) | \
+ (I2C_CR2_START)) & (~I2C_CR2_RD_WRN)))
#define SMBUS_GET_ADDR_MATCH(__HANDLE__) (((__HANDLE__)->Instance->ISR & I2C_ISR_ADDCODE) >> 17U)
#define SMBUS_GET_DIR(__HANDLE__) (((__HANDLE__)->Instance->ISR & I2C_ISR_DIR) >> 16U)
@@ -648,11 +673,14 @@
/* Callbacks Register/UnRegister functions ***********************************/
#if (USE_HAL_SMBUS_REGISTER_CALLBACKS == 1)
-HAL_StatusTypeDef HAL_SMBUS_RegisterCallback(SMBUS_HandleTypeDef *hsmbus, HAL_SMBUS_CallbackIDTypeDef CallbackID,
+HAL_StatusTypeDef HAL_SMBUS_RegisterCallback(SMBUS_HandleTypeDef *hsmbus,
+ HAL_SMBUS_CallbackIDTypeDef CallbackID,
pSMBUS_CallbackTypeDef pCallback);
-HAL_StatusTypeDef HAL_SMBUS_UnRegisterCallback(SMBUS_HandleTypeDef *hsmbus, HAL_SMBUS_CallbackIDTypeDef CallbackID);
+HAL_StatusTypeDef HAL_SMBUS_UnRegisterCallback(SMBUS_HandleTypeDef *hsmbus,
+ HAL_SMBUS_CallbackIDTypeDef CallbackID);
-HAL_StatusTypeDef HAL_SMBUS_RegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus, pSMBUS_AddrCallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_SMBUS_RegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus,
+ pSMBUS_AddrCallbackTypeDef pCallback);
HAL_StatusTypeDef HAL_SMBUS_UnRegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus);
#endif /* USE_HAL_SMBUS_REGISTER_CALLBACKS */
/**
@@ -678,10 +706,10 @@
* @{
*/
/******* Non-Blocking mode: Interrupt */
-HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData,
- uint16_t Size, uint32_t XferOptions);
-HAL_StatusTypeDef HAL_SMBUS_Master_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData,
- uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress,
+ uint8_t *pData, uint16_t Size, uint32_t XferOptions);
+HAL_StatusTypeDef HAL_SMBUS_Master_Receive_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress,
+ uint8_t *pData, uint16_t Size, uint32_t XferOptions);
HAL_StatusTypeDef HAL_SMBUS_Master_Abort_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress);
HAL_StatusTypeDef HAL_SMBUS_Slave_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint8_t *pData, uint16_t Size,
uint32_t XferOptions);
diff --git a/Inc/stm32wlxx_hal_smbus_ex.h b/Inc/stm32wlxx_hal_smbus_ex.h
new file mode 100644
index 0000000..82327b1
--- /dev/null
+++ b/Inc/stm32wlxx_hal_smbus_ex.h
@@ -0,0 +1,138 @@
+/**
+ ******************************************************************************
+ * @file stm32wlxx_hal_smbus_ex.h
+ * @author MCD Application Team
+ * @brief Header file of SMBUS HAL Extended module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2020 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32WLxx_HAL_SMBUS_EX_H
+#define STM32WLxx_HAL_SMBUS_EX_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32wlxx_hal_def.h"
+
+/** @addtogroup STM32WLxx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup SMBUSEx
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup SMBUSEx_Exported_Constants SMBUS Extended Exported Constants
+ * @{
+ */
+
+/** @defgroup SMBUSEx_FastModePlus SMBUS Extended Fast Mode Plus
+ * @{
+ */
+#define SMBUS_FASTMODEPLUS_PB6 SYSCFG_CFGR1_I2C_PB6_FMP /*!< Enable Fast Mode Plus on PB6 */
+#define SMBUS_FASTMODEPLUS_PB7 SYSCFG_CFGR1_I2C_PB7_FMP /*!< Enable Fast Mode Plus on PB7 */
+#define SMBUS_FASTMODEPLUS_PB8 SYSCFG_CFGR1_I2C_PB8_FMP /*!< Enable Fast Mode Plus on PB8 */
+#define SMBUS_FASTMODEPLUS_PB9 SYSCFG_CFGR1_I2C_PB9_FMP /*!< Enable Fast Mode Plus on PB9 */
+#define SMBUS_FASTMODEPLUS_I2C1 SYSCFG_CFGR1_I2C1_FMP /*!< Enable Fast Mode Plus on I2C1 pins */
+#define SMBUS_FASTMODEPLUS_I2C2 SYSCFG_CFGR1_I2C2_FMP /*!< Enable Fast Mode Plus on I2C2 pins */
+#define SMBUS_FASTMODEPLUS_I2C3 SYSCFG_CFGR1_I2C3_FMP /*!< Enable Fast Mode Plus on I2C3 pins */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+/** @defgroup SMBUSEx_Exported_Macros SMBUS Extended Exported Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup SMBUSEx_Exported_Functions SMBUS Extended Exported Functions
+ * @{
+ */
+
+/** @addtogroup SMBUSEx_Exported_Functions_Group3 SMBUS Extended FastModePlus Functions
+ * @{
+ */
+void HAL_SMBUSEx_EnableFastModePlus(uint32_t ConfigFastModePlus);
+void HAL_SMBUSEx_DisableFastModePlus(uint32_t ConfigFastModePlus);
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup SMBUSEx_Private_Constants SMBUS Extended Private Constants
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/* Private macros ------------------------------------------------------------*/
+/** @defgroup SMBUSEx_Private_Macro SMBUS Extended Private Macros
+ * @{
+ */
+#define IS_SMBUS_FASTMODEPLUS(__CONFIG__) ((((__CONFIG__) & (SMBUS_FASTMODEPLUS_PB6)) == SMBUS_FASTMODEPLUS_PB6) || \
+ (((__CONFIG__) & (SMBUS_FASTMODEPLUS_PB7)) == SMBUS_FASTMODEPLUS_PB7) || \
+ (((__CONFIG__) & (SMBUS_FASTMODEPLUS_PB8)) == SMBUS_FASTMODEPLUS_PB8) || \
+ (((__CONFIG__) & (SMBUS_FASTMODEPLUS_PB9)) == SMBUS_FASTMODEPLUS_PB9) || \
+ (((__CONFIG__) & (SMBUS_FASTMODEPLUS_I2C1)) == SMBUS_FASTMODEPLUS_I2C1) || \
+ (((__CONFIG__) & (SMBUS_FASTMODEPLUS_I2C2)) == SMBUS_FASTMODEPLUS_I2C2) || \
+ (((__CONFIG__) & (SMBUS_FASTMODEPLUS_I2C3)) == SMBUS_FASTMODEPLUS_I2C3))
+/**
+ * @}
+ */
+
+/* Private Functions ---------------------------------------------------------*/
+/** @defgroup SMBUSEx_Private_Functions SMBUS Extended Private Functions
+ * @{
+ */
+/* Private functions are defined in stm32wlxx_hal_smbus_ex.c file */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32WLxx_HAL_SMBUS_EX_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/Inc/stm32wlxx_hal_subghz.h b/Inc/stm32wlxx_hal_subghz.h
index 754c805..1d5ff01 100644
--- a/Inc/stm32wlxx_hal_subghz.h
+++ b/Inc/stm32wlxx_hal_subghz.h
@@ -51,7 +51,7 @@
{
uint32_t BaudratePrescaler; /*!< Specifies the Baud Rate prescaler value which will be
used to configure SUBGHZSPI clock.
- This parameter can be a value of @ref SUBGHZSPI_BAUDRATE_Prescaler */
+ This parameter can be a value of @ref SUBGHZ_SPI_BAUDRATE_Prescaler */
} SUBGHZ_InitTypeDef;
/**
@@ -207,7 +207,7 @@
* @}
*/
-/** @defgroup SUBGHZSPI_BAUDRATE_Prescaler SUBGHZ BaudRate Prescaler
+/** @defgroup SUBGHZ_SPI_BAUDRATE_Prescaler SUBGHZ BaudRate Prescaler
* @{
*/
#define SUBGHZSPI_BAUDRATEPRESCALER_2 (0x00000000U)
@@ -305,7 +305,7 @@
/** @brief Checks if SUBGHZSPI Baudrate prescaler parameter is in allowed range.
* @param __PRESCALER__ specifies the SUBGHZSPI Baudrate prescaler.
- * This parameter can be a value of @ref SUBGHZSPI_BAUDRATE_Prescaler
+ * This parameter can be a value of @ref SUBGHZ_SPI_BAUDRATE_Prescaler
* @retval None
*/
#define IS_SUBGHZSPI_BAUDRATE_PRESCALER(__PRESCALER__) (((__PRESCALER__) == SUBGHZSPI_BAUDRATEPRESCALER_2) || \
diff --git a/Inc/stm32wlxx_hal_tim.h b/Inc/stm32wlxx_hal_tim.h
index dd7a9e0..6efaa40 100644
--- a/Inc/stm32wlxx_hal_tim.h
+++ b/Inc/stm32wlxx_hal_tim.h
@@ -1073,24 +1073,24 @@
/** @defgroup TIM_DMA_Burst_Length TIM DMA Burst Length
* @{
*/
-#define TIM_DMABURSTLENGTH_1TRANSFER 0x00000000U /*!< The transfer is done to 1 register starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_2TRANSFERS 0x00000100U /*!< The transfer is done to 2 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_3TRANSFERS 0x00000200U /*!< The transfer is done to 3 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_4TRANSFERS 0x00000300U /*!< The transfer is done to 4 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_5TRANSFERS 0x00000400U /*!< The transfer is done to 5 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_6TRANSFERS 0x00000500U /*!< The transfer is done to 6 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_7TRANSFERS 0x00000600U /*!< The transfer is done to 7 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_8TRANSFERS 0x00000700U /*!< The transfer is done to 8 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_9TRANSFERS 0x00000800U /*!< The transfer is done to 9 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_10TRANSFERS 0x00000900U /*!< The transfer is done to 10 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_11TRANSFERS 0x00000A00U /*!< The transfer is done to 11 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_12TRANSFERS 0x00000B00U /*!< The transfer is done to 12 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_13TRANSFERS 0x00000C00U /*!< The transfer is done to 13 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_14TRANSFERS 0x00000D00U /*!< The transfer is done to 14 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_15TRANSFERS 0x00000E00U /*!< The transfer is done to 15 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_16TRANSFERS 0x00000F00U /*!< The transfer is done to 16 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_17TRANSFERS 0x00001000U /*!< The transfer is done to 17 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
-#define TIM_DMABURSTLENGTH_18TRANSFERS 0x00001100U /*!< The transfer is done to 18 registers starting trom TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_1TRANSFER 0x00000000U /*!< The transfer is done to 1 register starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_2TRANSFERS 0x00000100U /*!< The transfer is done to 2 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_3TRANSFERS 0x00000200U /*!< The transfer is done to 3 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_4TRANSFERS 0x00000300U /*!< The transfer is done to 4 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_5TRANSFERS 0x00000400U /*!< The transfer is done to 5 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_6TRANSFERS 0x00000500U /*!< The transfer is done to 6 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_7TRANSFERS 0x00000600U /*!< The transfer is done to 7 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_8TRANSFERS 0x00000700U /*!< The transfer is done to 8 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_9TRANSFERS 0x00000800U /*!< The transfer is done to 9 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_10TRANSFERS 0x00000900U /*!< The transfer is done to 10 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_11TRANSFERS 0x00000A00U /*!< The transfer is done to 11 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_12TRANSFERS 0x00000B00U /*!< The transfer is done to 12 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_13TRANSFERS 0x00000C00U /*!< The transfer is done to 13 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_14TRANSFERS 0x00000D00U /*!< The transfer is done to 14 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_15TRANSFERS 0x00000E00U /*!< The transfer is done to 15 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_16TRANSFERS 0x00000F00U /*!< The transfer is done to 16 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_17TRANSFERS 0x00001000U /*!< The transfer is done to 17 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
+#define TIM_DMABURSTLENGTH_18TRANSFERS 0x00001100U /*!< The transfer is done to 18 registers starting from TIMx_CR1 + TIMx_DCR.DBA */
/**
* @}
*/
diff --git a/Inc/stm32wlxx_hal_uart.h b/Inc/stm32wlxx_hal_uart.h
index b8f4a23..f2006d5 100644
--- a/Inc/stm32wlxx_hal_uart.h
+++ b/Inc/stm32wlxx_hal_uart.h
@@ -1137,10 +1137,10 @@
* @param __HANDLE__ specifies the UART Handle.
* @retval None
*/
-#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \
- do{ \
- SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
- (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \
+#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \
+ do{ \
+ ATOMIC_SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
+ (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \
} while(0U)
/** @brief Disable CTS flow control.
@@ -1156,10 +1156,10 @@
* @param __HANDLE__ specifies the UART Handle.
* @retval None
*/
-#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \
- do{ \
- CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
- (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \
+#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \
+ do{ \
+ ATOMIC_CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
+ (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \
} while(0U)
/** @brief Enable RTS flow control.
@@ -1175,10 +1175,10 @@
* @param __HANDLE__ specifies the UART Handle.
* @retval None
*/
-#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \
- do{ \
- SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \
- (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \
+#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \
+ do{ \
+ ATOMIC_SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \
+ (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \
} while(0U)
/** @brief Disable RTS flow control.
@@ -1194,10 +1194,10 @@
* @param __HANDLE__ specifies the UART Handle.
* @retval None
*/
-#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \
- do{ \
- CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\
- (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \
+#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \
+ do{ \
+ ATOMIC_CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\
+ (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \
} while(0U)
/**
* @}
diff --git a/Inc/stm32wlxx_ll_adc.h b/Inc/stm32wlxx_ll_adc.h
index a5dee26..17de5aa 100644
--- a/Inc/stm32wlxx_ll_adc.h
+++ b/Inc/stm32wlxx_ll_adc.h
@@ -54,14 +54,14 @@
/* Definition of ADC group regular sequencer bits information to be inserted */
/* into ADC group regular sequencer ranks literals definition. */
-#define ADC_REG_RANK_1_SQRX_BITOFFSET_POS ( 0UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ1" position in register */
-#define ADC_REG_RANK_2_SQRX_BITOFFSET_POS ( 4UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ2" position in register */
-#define ADC_REG_RANK_3_SQRX_BITOFFSET_POS ( 8UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ3" position in register */
-#define ADC_REG_RANK_4_SQRX_BITOFFSET_POS (12UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ4" position in register */
-#define ADC_REG_RANK_5_SQRX_BITOFFSET_POS (16UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ5" position in register */
-#define ADC_REG_RANK_6_SQRX_BITOFFSET_POS (20UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ6" position in register */
-#define ADC_REG_RANK_7_SQRX_BITOFFSET_POS (24UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ7" position in register */
-#define ADC_REG_RANK_8_SQRX_BITOFFSET_POS (28UL) /* Value equivalent to bitfield "ADC_CHSELR_SQ8" position in register */
+#define ADC_REG_RANK_1_SQRX_BITOFFSET_POS ( 0UL) /* Equivalent to bitfield "ADC_CHSELR_SQ1" position in register */
+#define ADC_REG_RANK_2_SQRX_BITOFFSET_POS ( 4UL) /* Equivalent to bitfield "ADC_CHSELR_SQ2" position in register */
+#define ADC_REG_RANK_3_SQRX_BITOFFSET_POS ( 8UL) /* Equivalent to bitfield "ADC_CHSELR_SQ3" position in register */
+#define ADC_REG_RANK_4_SQRX_BITOFFSET_POS (12UL) /* Equivalent to bitfield "ADC_CHSELR_SQ4" position in register */
+#define ADC_REG_RANK_5_SQRX_BITOFFSET_POS (16UL) /* Equivalent to bitfield "ADC_CHSELR_SQ5" position in register */
+#define ADC_REG_RANK_6_SQRX_BITOFFSET_POS (20UL) /* Equivalent to bitfield "ADC_CHSELR_SQ6" position in register */
+#define ADC_REG_RANK_7_SQRX_BITOFFSET_POS (24UL) /* Equivalent to bitfield "ADC_CHSELR_SQ7" position in register */
+#define ADC_REG_RANK_8_SQRX_BITOFFSET_POS (28UL) /* Equivalent to bitfield "ADC_CHSELR_SQ8" position in register */
@@ -88,8 +88,8 @@
((ADC_REG_TRIG_EXT_EDGE_DEFAULT) << (4U * 3UL)) )
/* Definition of ADC group regular trigger bits information. */
-#define ADC_REG_TRIG_EXTSEL_BITOFFSET_POS ( 6UL) /* Value equivalent to bitfield "ADC_CFGR1_EXTSEL" position in register */
-#define ADC_REG_TRIG_EXTEN_BITOFFSET_POS (10UL) /* Value equivalent to bitfield "ADC_CFGR1_EXTEN" position in register */
+#define ADC_REG_TRIG_EXTSEL_BITOFFSET_POS ( 6UL) /* Equivalent to bitfield "ADC_CFGR1_EXTSEL" position in register */
+#define ADC_REG_TRIG_EXTEN_BITOFFSET_POS (10UL) /* Equivalent to bitfield "ADC_CFGR1_EXTEN" position in register */
@@ -101,8 +101,8 @@
/* GPIO pins) and internal channels (connected to internal paths) */
#define ADC_CHANNEL_ID_NUMBER_MASK (ADC_CFGR1_AWD1CH)
#define ADC_CHANNEL_ID_BITFIELD_MASK (ADC_CHSELR_CHSEL)
-#define ADC_CHANNEL_ID_NUMBER_MASK_SEQ (ADC_CHSELR_SQ1 << ADC_CHANNEL_ID_NUMBER_BITOFFSET_POS) /* Value equivalent to ADC_CHANNEL_ID_NUMBER_MASK with reduced range: on this STM32 series, ADC group regular sequencer, if set to mode "fully configurable", can contain channels with a restricted channel number. Refer to function @ref LL_ADC_REG_SetSequencerConfigurable(). */
-#define ADC_CHANNEL_ID_NUMBER_BITOFFSET_POS (26UL)/* Value equivalent to bitfield "ADC_CHANNEL_ID_NUMBER_MASK" position in register */
+#define ADC_CHANNEL_ID_NUMBER_MASK_SEQ (ADC_CHSELR_SQ1 << ADC_CHANNEL_ID_NUMBER_BITOFFSET_POS) /* Equivalent to ADC_CHANNEL_ID_NUMBER_MASK with reduced range: on this STM32 series, ADC group regular sequencer, if set to mode "fully configurable", can contain channels with a restricted channel number. Refer to function @ref LL_ADC_REG_SetSequencerConfigurable(). */
+#define ADC_CHANNEL_ID_NUMBER_BITOFFSET_POS (26UL)/* Equivalent to bitfield "ADC_CHANNEL_ID_NUMBER_MASK" position in register */
#define ADC_CHANNEL_ID_MASK (ADC_CHANNEL_ID_NUMBER_MASK | ADC_CHANNEL_ID_BITFIELD_MASK | \
ADC_CHANNEL_ID_INTERNAL_CH_MASK)
/* Equivalent mask of ADC_CHANNEL_NUMBER_MASK aligned on register LSB (bit 0) */
@@ -210,31 +210,31 @@
/* ADC registers bits positions */
-#define ADC_CFGR1_RES_BITOFFSET_POS ( 3UL) /* Value equivalent to bitfield "ADC_CFGR1_RES" position in register */
-#define ADC_CFGR1_AWDSGL_BITOFFSET_POS (22UL) /* Value equivalent to bitfield "ADC_CFGR1_AWDSGL" position in register */
-#define ADC_TR1_HT1_BITOFFSET_POS (16UL) /* Value equivalent to bitfield "ADC_TR1_HT1" position in register */
-#define ADC_CHSELR_CHSEL0_BITOFFSET_POS ( 0UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL0" position in register */
-#define ADC_CHSELR_CHSEL1_BITOFFSET_POS ( 1UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL1" position in register */
-#define ADC_CHSELR_CHSEL2_BITOFFSET_POS ( 2UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL2" position in register */
-#define ADC_CHSELR_CHSEL3_BITOFFSET_POS ( 3UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL3" position in register */
-#define ADC_CHSELR_CHSEL4_BITOFFSET_POS ( 4UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL4" position in register */
-#define ADC_CHSELR_CHSEL5_BITOFFSET_POS ( 5UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL5" position in register */
-#define ADC_CHSELR_CHSEL6_BITOFFSET_POS ( 6UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL6" position in register */
-#define ADC_CHSELR_CHSEL7_BITOFFSET_POS ( 7UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL7" position in register */
-#define ADC_CHSELR_CHSEL8_BITOFFSET_POS ( 8UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL8" position in register */
-#define ADC_CHSELR_CHSEL9_BITOFFSET_POS ( 9UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL9" position in register */
-#define ADC_CHSELR_CHSEL10_BITOFFSET_POS (10UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL10" position in register */
-#define ADC_CHSELR_CHSEL11_BITOFFSET_POS (11UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL11" position in register */
-#define ADC_CHSELR_CHSEL12_BITOFFSET_POS (12UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL12" position in register */
-#define ADC_CHSELR_CHSEL13_BITOFFSET_POS (13UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL13" position in register */
-#define ADC_CHSELR_CHSEL14_BITOFFSET_POS (14UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL14" position in register */
-#define ADC_CHSELR_CHSEL15_BITOFFSET_POS (15UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL15" position in register */
-#define ADC_CHSELR_CHSEL16_BITOFFSET_POS (16UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL16" position in register */
-#define ADC_CHSELR_CHSEL17_BITOFFSET_POS (17UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL17" position in register */
-#define ADC_CHSELR_CHSEL18_BITOFFSET_POS (18UL) /* Value equivalent to bitfield "ADC_CHSELR_CHSEL18" position in register */
-#define ADC_SMPR_SMP1_BITOFFSET_POS ( 0UL) /* Value equivalent to bitfield "ADC_SMPR_SMP1" position in register */
-#define ADC_SMPR_SMP2_BITOFFSET_POS ( 4UL) /* Value equivalent to bitfield "ADC_SMPR_SMP2" position in register */
-#define ADC_SMPR_SMPSEL0_BITOFFSET_POS ( 8UL) /* Value equivalent to bitfield "ADC_SMPR_SMPSEL0" position in register */
+#define ADC_CFGR1_RES_BITOFFSET_POS ( 3UL) /* Equivalent to bitfield "ADC_CFGR1_RES" position in register */
+#define ADC_CFGR1_AWDSGL_BITOFFSET_POS (22UL) /* Equivalent to bitfield "ADC_CFGR1_AWDSGL" position in register */
+#define ADC_TR1_HT1_BITOFFSET_POS (16UL) /* Equivalent to bitfield "ADC_TR1_HT1" position in register */
+#define ADC_CHSELR_CHSEL0_BITOFFSET_POS ( 0UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL0" position in register */
+#define ADC_CHSELR_CHSEL1_BITOFFSET_POS ( 1UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL1" position in register */
+#define ADC_CHSELR_CHSEL2_BITOFFSET_POS ( 2UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL2" position in register */
+#define ADC_CHSELR_CHSEL3_BITOFFSET_POS ( 3UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL3" position in register */
+#define ADC_CHSELR_CHSEL4_BITOFFSET_POS ( 4UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL4" position in register */
+#define ADC_CHSELR_CHSEL5_BITOFFSET_POS ( 5UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL5" position in register */
+#define ADC_CHSELR_CHSEL6_BITOFFSET_POS ( 6UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL6" position in register */
+#define ADC_CHSELR_CHSEL7_BITOFFSET_POS ( 7UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL7" position in register */
+#define ADC_CHSELR_CHSEL8_BITOFFSET_POS ( 8UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL8" position in register */
+#define ADC_CHSELR_CHSEL9_BITOFFSET_POS ( 9UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL9" position in register */
+#define ADC_CHSELR_CHSEL10_BITOFFSET_POS (10UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL10" position in register */
+#define ADC_CHSELR_CHSEL11_BITOFFSET_POS (11UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL11" position in register */
+#define ADC_CHSELR_CHSEL12_BITOFFSET_POS (12UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL12" position in register */
+#define ADC_CHSELR_CHSEL13_BITOFFSET_POS (13UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL13" position in register */
+#define ADC_CHSELR_CHSEL14_BITOFFSET_POS (14UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL14" position in register */
+#define ADC_CHSELR_CHSEL15_BITOFFSET_POS (15UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL15" position in register */
+#define ADC_CHSELR_CHSEL16_BITOFFSET_POS (16UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL16" position in register */
+#define ADC_CHSELR_CHSEL17_BITOFFSET_POS (17UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL17" position in register */
+#define ADC_CHSELR_CHSEL18_BITOFFSET_POS (18UL) /* Equivalent to bitfield "ADC_CHSELR_CHSEL18" position in register */
+#define ADC_SMPR_SMP1_BITOFFSET_POS ( 0UL) /* Equivalent to bitfield "ADC_SMPR_SMP1" position in register */
+#define ADC_SMPR_SMP2_BITOFFSET_POS ( 4UL) /* Equivalent to bitfield "ADC_SMPR_SMP2" position in register */
+#define ADC_SMPR_SMPSEL0_BITOFFSET_POS ( 8UL) /* Equivalent to bitfield "ADC_SMPR_SMPSEL0" position in register */
/* ADC registers bits groups */
@@ -329,7 +329,6 @@
ADC clock synchronous (from PCLK) with prescaler 1 must be enabled only if PCLK has a 50% duty clock cycle
(APB prescaler configured inside the RCC must be bypassed and the system clock must by 50% duty cycle).
-
This feature can be modified afterwards using unitary function @ref LL_ADC_SetClock().
For more details, refer to description of this function. */
@@ -2318,17 +2317,17 @@
*/
__STATIC_INLINE uint32_t LL_ADC_REG_GetTriggerSource(ADC_TypeDef *ADCx)
{
- __IO uint32_t TriggerSource = READ_BIT(ADCx->CFGR1, ADC_CFGR1_EXTSEL | ADC_CFGR1_EXTEN);
+ __IO uint32_t trigger_source = READ_BIT(ADCx->CFGR1, ADC_CFGR1_EXTSEL | ADC_CFGR1_EXTEN);
/* Value for shift of {0; 4; 8; 12} depending on value of bitfield */
/* corresponding to ADC_CFGR1_EXTEN {0; 1; 2; 3}. */
- uint32_t ShiftExten = ((TriggerSource & ADC_CFGR1_EXTEN) >> (ADC_REG_TRIG_EXTEN_BITOFFSET_POS - 2UL));
+ uint32_t shift_exten = ((trigger_source & ADC_CFGR1_EXTEN) >> (ADC_REG_TRIG_EXTEN_BITOFFSET_POS - 2UL));
/* Set bitfield corresponding to ADC_CFGR1_EXTEN and ADC_CFGR1_EXTSEL */
/* to match with triggers literals definition. */
- return ((TriggerSource
- & (ADC_REG_TRIG_SOURCE_MASK >> ShiftExten) & ADC_CFGR1_EXTSEL)
- | ((ADC_REG_TRIG_EDGE_MASK >> ShiftExten) & ADC_CFGR1_EXTEN)
+ return ((trigger_source
+ & (ADC_REG_TRIG_SOURCE_MASK >> shift_exten) & ADC_CFGR1_EXTSEL)
+ | ((ADC_REG_TRIG_EDGE_MASK >> shift_exten) & ADC_CFGR1_EXTEN)
);
}
@@ -2575,21 +2574,21 @@
*/
__STATIC_INLINE uint32_t LL_ADC_REG_GetSequencerLength(ADC_TypeDef *ADCx)
{
- __IO uint32_t ChannelsRanks = READ_BIT(ADCx->CHSELR, ADC_CHSELR_SQ_ALL);
- uint32_t SequencerLength = LL_ADC_REG_SEQ_SCAN_ENABLE_8RANKS;
- uint32_t RankIndex;
+ __IO uint32_t channels_ranks = READ_BIT(ADCx->CHSELR, ADC_CHSELR_SQ_ALL);
+ uint32_t sequencer_length = LL_ADC_REG_SEQ_SCAN_ENABLE_8RANKS;
+ uint32_t rank_index;
/* Parse register for end of sequence identifier */
- for (RankIndex = 0UL; RankIndex < (32U - 4U); RankIndex += 4U)
+ for (rank_index = 0UL; rank_index < (32U - 4U); rank_index += 4U)
{
- if ((ChannelsRanks & (ADC_CHSELR_SQ2 << RankIndex)) == (ADC_CHSELR_SQ2 << RankIndex))
+ if ((channels_ranks & (ADC_CHSELR_SQ2 << rank_index)) == (ADC_CHSELR_SQ2 << rank_index))
{
- SequencerLength = (ADC_CHSELR_SQ2 << RankIndex);
+ sequencer_length = (ADC_CHSELR_SQ2 << rank_index);
break;
}
}
- return SequencerLength;
+ return sequencer_length;
}
/**
@@ -3194,26 +3193,26 @@
*/
__STATIC_INLINE uint32_t LL_ADC_REG_GetSequencerChannels(ADC_TypeDef *ADCx)
{
- uint32_t ChannelsBitfield = (uint32_t)READ_BIT(ADCx->CHSELR, ADC_CHSELR_CHSEL);
+ uint32_t channels_bitfield = (uint32_t)READ_BIT(ADCx->CHSELR, ADC_CHSELR_CHSEL);
- return ((((ChannelsBitfield & ADC_CHSELR_CHSEL0) >> ADC_CHSELR_CHSEL0_BITOFFSET_POS) * LL_ADC_CHANNEL_0)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL1) >> ADC_CHSELR_CHSEL1_BITOFFSET_POS) * LL_ADC_CHANNEL_1)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL2) >> ADC_CHSELR_CHSEL2_BITOFFSET_POS) * LL_ADC_CHANNEL_2)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL3) >> ADC_CHSELR_CHSEL3_BITOFFSET_POS) * LL_ADC_CHANNEL_3)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL4) >> ADC_CHSELR_CHSEL4_BITOFFSET_POS) * LL_ADC_CHANNEL_4)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL5) >> ADC_CHSELR_CHSEL5_BITOFFSET_POS) * LL_ADC_CHANNEL_5)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL6) >> ADC_CHSELR_CHSEL6_BITOFFSET_POS) * LL_ADC_CHANNEL_6)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL7) >> ADC_CHSELR_CHSEL7_BITOFFSET_POS) * LL_ADC_CHANNEL_7)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL8) >> ADC_CHSELR_CHSEL8_BITOFFSET_POS) * LL_ADC_CHANNEL_8)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL9) >> ADC_CHSELR_CHSEL9_BITOFFSET_POS) * LL_ADC_CHANNEL_9)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL10) >> ADC_CHSELR_CHSEL10_BITOFFSET_POS) * LL_ADC_CHANNEL_10)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL11) >> ADC_CHSELR_CHSEL11_BITOFFSET_POS) * LL_ADC_CHANNEL_11)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL12) >> ADC_CHSELR_CHSEL12_BITOFFSET_POS) * LL_ADC_CHANNEL_12)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL13) >> ADC_CHSELR_CHSEL13_BITOFFSET_POS) * LL_ADC_CHANNEL_13)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL14) >> ADC_CHSELR_CHSEL14_BITOFFSET_POS) * LL_ADC_CHANNEL_14)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL15) >> ADC_CHSELR_CHSEL15_BITOFFSET_POS) * LL_ADC_CHANNEL_15)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL16) >> ADC_CHSELR_CHSEL16_BITOFFSET_POS) * LL_ADC_CHANNEL_16)
- | (((ChannelsBitfield & ADC_CHSELR_CHSEL17) >> ADC_CHSELR_CHSEL17_BITOFFSET_POS) * LL_ADC_CHANNEL_17)
+ return ((((channels_bitfield & ADC_CHSELR_CHSEL0) >> ADC_CHSELR_CHSEL0_BITOFFSET_POS) * LL_ADC_CHANNEL_0)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL1) >> ADC_CHSELR_CHSEL1_BITOFFSET_POS) * LL_ADC_CHANNEL_1)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL2) >> ADC_CHSELR_CHSEL2_BITOFFSET_POS) * LL_ADC_CHANNEL_2)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL3) >> ADC_CHSELR_CHSEL3_BITOFFSET_POS) * LL_ADC_CHANNEL_3)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL4) >> ADC_CHSELR_CHSEL4_BITOFFSET_POS) * LL_ADC_CHANNEL_4)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL5) >> ADC_CHSELR_CHSEL5_BITOFFSET_POS) * LL_ADC_CHANNEL_5)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL6) >> ADC_CHSELR_CHSEL6_BITOFFSET_POS) * LL_ADC_CHANNEL_6)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL7) >> ADC_CHSELR_CHSEL7_BITOFFSET_POS) * LL_ADC_CHANNEL_7)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL8) >> ADC_CHSELR_CHSEL8_BITOFFSET_POS) * LL_ADC_CHANNEL_8)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL9) >> ADC_CHSELR_CHSEL9_BITOFFSET_POS) * LL_ADC_CHANNEL_9)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL10) >> ADC_CHSELR_CHSEL10_BITOFFSET_POS) * LL_ADC_CHANNEL_10)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL11) >> ADC_CHSELR_CHSEL11_BITOFFSET_POS) * LL_ADC_CHANNEL_11)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL12) >> ADC_CHSELR_CHSEL12_BITOFFSET_POS) * LL_ADC_CHANNEL_12)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL13) >> ADC_CHSELR_CHSEL13_BITOFFSET_POS) * LL_ADC_CHANNEL_13)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL14) >> ADC_CHSELR_CHSEL14_BITOFFSET_POS) * LL_ADC_CHANNEL_14)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL15) >> ADC_CHSELR_CHSEL15_BITOFFSET_POS) * LL_ADC_CHANNEL_15)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL16) >> ADC_CHSELR_CHSEL16_BITOFFSET_POS) * LL_ADC_CHANNEL_16)
+ | (((channels_bitfield & ADC_CHSELR_CHSEL17) >> ADC_CHSELR_CHSEL17_BITOFFSET_POS) * LL_ADC_CHANNEL_17)
);
}
@@ -3717,55 +3716,55 @@
__IO uint32_t *preg = __ADC_PTR_REG_OFFSET(ADCx->CFGR1, ((AWDy & ADC_AWD_CRX_REGOFFSET_MASK) >> ADC_AWD_CRX_REGOFFSET_POS)
+ ((AWDy & ADC_AWD_CR12_REGOFFSETGAP_MASK) * ADC_AWD_CR12_REGOFFSETGAP_VAL));
- uint32_t AnalogWDMonitChannels = (READ_BIT(*preg, AWDy) & AWDy & ADC_AWD_CR_ALL_CHANNEL_MASK);
+ uint32_t analog_wd_monit_channels = (READ_BIT(*preg, AWDy) & AWDy & ADC_AWD_CR_ALL_CHANNEL_MASK);
- /* If "AnalogWDMonitChannels" == 0, then the selected AWD is disabled */
+ /* If "analog_wd_monit_channels" == 0, then the selected AWD is disabled */
/* (parameter value LL_ADC_AWD_DISABLE). */
/* Else, the selected AWD is enabled and is monitoring a group of channels */
/* or a single channel. */
- if (AnalogWDMonitChannels != 0UL)
+ if (analog_wd_monit_channels != 0UL)
{
if (AWDy == LL_ADC_AWD1)
{
- if ((AnalogWDMonitChannels & ADC_CFGR1_AWD1SGL) == 0UL)
+ if ((analog_wd_monit_channels & ADC_CFGR1_AWD1SGL) == 0UL)
{
/* AWD monitoring a group of channels */
- AnalogWDMonitChannels = ((AnalogWDMonitChannels
- | (ADC_AWD_CR23_CHANNEL_MASK)
- )
- & (~(ADC_CFGR1_AWD1CH))
- );
+ analog_wd_monit_channels = ((analog_wd_monit_channels
+ | (ADC_AWD_CR23_CHANNEL_MASK)
+ )
+ & (~(ADC_CFGR1_AWD1CH))
+ );
}
else
{
/* AWD monitoring a single channel */
- AnalogWDMonitChannels = (AnalogWDMonitChannels
- | (ADC_AWD2CR_AWD2CH_0 << (AnalogWDMonitChannels >> ADC_CFGR1_AWD1CH_Pos))
- );
+ analog_wd_monit_channels = (analog_wd_monit_channels
+ | (ADC_AWD2CR_AWD2CH_0 << (analog_wd_monit_channels >> ADC_CFGR1_AWD1CH_Pos))
+ );
}
}
else
{
- if ((AnalogWDMonitChannels & ADC_AWD_CR23_CHANNEL_MASK) == ADC_AWD_CR23_CHANNEL_MASK)
+ if ((analog_wd_monit_channels & ADC_AWD_CR23_CHANNEL_MASK) == ADC_AWD_CR23_CHANNEL_MASK)
{
/* AWD monitoring a group of channels */
- AnalogWDMonitChannels = (ADC_AWD_CR23_CHANNEL_MASK
- | (ADC_CFGR1_AWD1EN)
- );
+ analog_wd_monit_channels = (ADC_AWD_CR23_CHANNEL_MASK
+ | (ADC_CFGR1_AWD1EN)
+ );
}
else
{
/* AWD monitoring a single channel */
/* AWD monitoring a group of channels */
- AnalogWDMonitChannels = (AnalogWDMonitChannels
- | (ADC_CFGR1_AWD1EN | ADC_CFGR1_AWD1SGL)
- | (__LL_ADC_CHANNEL_TO_DECIMAL_NB(AnalogWDMonitChannels) << ADC_CFGR1_AWD1CH_Pos)
- );
+ analog_wd_monit_channels = (analog_wd_monit_channels
+ | (ADC_CFGR1_AWD1EN | ADC_CFGR1_AWD1SGL)
+ | (__LL_ADC_CHANNEL_TO_DECIMAL_NB(analog_wd_monit_channels) << ADC_CFGR1_AWD1CH_Pos)
+ );
}
}
}
- return AnalogWDMonitChannels;
+ return analog_wd_monit_channels;
}
/**
@@ -4731,7 +4730,7 @@
/**
* @brief Enable interruption ADC channel configuration ready.
- * @rmtoll IER ADRDYIE LL_ADC_EnableIT_CCRDY
+ * @rmtoll IER CCRDYIE LL_ADC_EnableIT_CCRDY
* @param ADCx ADC instance
* @retval State of bit (1 or 0).
*/
@@ -4841,7 +4840,7 @@
/**
* @brief Disable interruption ADC channel configuration ready.
- * @rmtoll IER ADRDYIE LL_ADC_DisableIT_CCRDY
+ * @rmtoll IER CCRDYIE LL_ADC_DisableIT_CCRDY
* @param ADCx ADC instance
* @retval State of bit (1 or 0).
*/
@@ -4952,7 +4951,7 @@
/**
* @brief Get state of interruption ADC channel configuration ready.
- * @rmtoll IER ADRDYIE LL_ADC_IsEnabledIT_CCRDY
+ * @rmtoll IER CCRDYIE LL_ADC_IsEnabledIT_CCRDY
* @param ADCx ADC instance
* @retval State of bit (1 or 0).
*/
@@ -5068,19 +5067,19 @@
/* Initialization of some features of ADC common parameters and multimode */
ErrorStatus LL_ADC_CommonDeInit(ADC_Common_TypeDef *ADCxy_COMMON);
-ErrorStatus LL_ADC_CommonInit(ADC_Common_TypeDef *ADCxy_COMMON, LL_ADC_CommonInitTypeDef *ADC_CommonInitStruct);
-void LL_ADC_CommonStructInit(LL_ADC_CommonInitTypeDef *ADC_CommonInitStruct);
+ErrorStatus LL_ADC_CommonInit(ADC_Common_TypeDef *ADCxy_COMMON, LL_ADC_CommonInitTypeDef *pADC_CommonInitStruct);
+void LL_ADC_CommonStructInit(LL_ADC_CommonInitTypeDef *pADC_CommonInitStruct);
/* De-initialization of ADC instance */
ErrorStatus LL_ADC_DeInit(ADC_TypeDef *ADCx);
/* Initialization of some features of ADC instance */
-ErrorStatus LL_ADC_Init(ADC_TypeDef *ADCx, LL_ADC_InitTypeDef *ADC_InitStruct);
-void LL_ADC_StructInit(LL_ADC_InitTypeDef *ADC_InitStruct);
+ErrorStatus LL_ADC_Init(ADC_TypeDef *ADCx, LL_ADC_InitTypeDef *pADC_InitStruct);
+void LL_ADC_StructInit(LL_ADC_InitTypeDef *pADC_InitStruct);
/* Initialization of some features of ADC instance and ADC group regular */
-ErrorStatus LL_ADC_REG_Init(ADC_TypeDef *ADCx, LL_ADC_REG_InitTypeDef *ADC_REG_InitStruct);
-void LL_ADC_REG_StructInit(LL_ADC_REG_InitTypeDef *ADC_REG_InitStruct);
+ErrorStatus LL_ADC_REG_Init(ADC_TypeDef *ADCx, LL_ADC_REG_InitTypeDef *pADC_RegInitStruct);
+void LL_ADC_REG_StructInit(LL_ADC_REG_InitTypeDef *pADC_RegInitStruct);
/**
* @}
diff --git a/Inc/stm32wlxx_ll_bus.h b/Inc/stm32wlxx_ll_bus.h
index 4fc39ec..8723f1a 100644
--- a/Inc/stm32wlxx_ll_bus.h
+++ b/Inc/stm32wlxx_ll_bus.h
@@ -1819,7 +1819,7 @@
* @rmtoll C2AHB2SMENR GPIOASMEN LL_C2_AHB2_GRP1_DisableClockSleep\n
* C2AHB2SMENR GPIOBSMEN LL_C2_AHB2_GRP1_DisableClockSleep\n
* C2AHB2SMENR GPIOCSMEN LL_C2_AHB2_GRP1_DisableClockSleep\n
- * C2AHB2SMENR GPIODSMEN LL_C2_AHB2_GRP1_DisableClockSleep\n
+ * C2AHB2SMENR GPIOHSMEN LL_C2_AHB2_GRP1_DisableClockSleep\n
* @param Periphs This parameter can be a combination of the following values:
* @arg @ref LL_C2_AHB2_GRP1_PERIPH_GPIOA
diff --git a/Inc/stm32wlxx_ll_cortex.h b/Inc/stm32wlxx_ll_cortex.h
index 12765e0..300b7bb 100644
--- a/Inc/stm32wlxx_ll_cortex.h
+++ b/Inc/stm32wlxx_ll_cortex.h
@@ -83,10 +83,9 @@
/**
* @}
*/
-
#endif /* CORE_CM0PLUS */
-#if __MPU_PRESENT
+#if __MPU_PRESENT
/** @defgroup CORTEX_LL_EC_CTRL_HFNMI_PRIVDEF MPU Control
* @{
*/
@@ -116,9 +115,12 @@
/** @defgroup CORTEX_LL_EC_REGION_SIZE MPU Region Size
* @{
*/
+#if defined(CORE_CM0PLUS)
+#else
#define LL_MPU_REGION_SIZE_32B (0x04U << MPU_RASR_SIZE_Pos) /*!< 32B Size of the MPU protection region */
#define LL_MPU_REGION_SIZE_64B (0x05U << MPU_RASR_SIZE_Pos) /*!< 64B Size of the MPU protection region */
#define LL_MPU_REGION_SIZE_128B (0x06U << MPU_RASR_SIZE_Pos) /*!< 128B Size of the MPU protection region */
+#endif
#define LL_MPU_REGION_SIZE_256B (0x07U << MPU_RASR_SIZE_Pos) /*!< 256B Size of the MPU protection region */
#define LL_MPU_REGION_SIZE_512B (0x08U << MPU_RASR_SIZE_Pos) /*!< 512B Size of the MPU protection region */
#define LL_MPU_REGION_SIZE_1KB (0x09U << MPU_RASR_SIZE_Pos) /*!< 1KB Size of the MPU protection region */
@@ -569,7 +571,7 @@
* @param Address Value of region base address
* @param SubRegionDisable Sub-region disable value between Min_Data = 0x00 and Max_Data = 0xFF
* @param Attributes This parameter can be a combination of the following values:
- * @arg @ref LL_MPU_REGION_SIZE_32B or @ref LL_MPU_REGION_SIZE_64B or @ref LL_MPU_REGION_SIZE_128B
+ * @arg @ref LL_MPU_REGION_SIZE_32B (*) or @ref LL_MPU_REGION_SIZE_64B (*) or @ref LL_MPU_REGION_SIZE_128B (*)
* or @ref LL_MPU_REGION_SIZE_256B or @ref LL_MPU_REGION_SIZE_512B or @ref LL_MPU_REGION_SIZE_1KB
* or @ref LL_MPU_REGION_SIZE_2KB or @ref LL_MPU_REGION_SIZE_4KB or @ref LL_MPU_REGION_SIZE_8KB
* or @ref LL_MPU_REGION_SIZE_16KB or @ref LL_MPU_REGION_SIZE_32KB or @ref LL_MPU_REGION_SIZE_64KB
@@ -586,6 +588,7 @@
* @arg @ref LL_MPU_ACCESS_SHAREABLE or @ref LL_MPU_ACCESS_NOT_SHAREABLE
* @arg @ref LL_MPU_ACCESS_CACHEABLE or @ref LL_MPU_ACCESS_NOT_CACHEABLE
* @arg @ref LL_MPU_ACCESS_BUFFERABLE or @ref LL_MPU_ACCESS_NOT_BUFFERABLE
+ * (*) value not defined for CM0+ core.
* @retval None
*/
__STATIC_INLINE void LL_MPU_ConfigRegion(uint32_t Region, uint32_t SubRegionDisable, uint32_t Address,
diff --git a/Inc/stm32wlxx_ll_i2c.h b/Inc/stm32wlxx_ll_i2c.h
index d85ec67..92823af 100644
--- a/Inc/stm32wlxx_ll_i2c.h
+++ b/Inc/stm32wlxx_ll_i2c.h
@@ -69,38 +69,46 @@
uint32_t PeripheralMode; /*!< Specifies the peripheral mode.
This parameter can be a value of @ref I2C_LL_EC_PERIPHERAL_MODE.
- This feature can be modified afterwards using unitary function @ref LL_I2C_SetMode(). */
+ This feature can be modified afterwards using unitary function
+ @ref LL_I2C_SetMode(). */
uint32_t Timing; /*!< Specifies the SDA setup, hold time and the SCL high, low period values.
This parameter must be set by referring to the STM32CubeMX Tool and
the helper macro @ref __LL_I2C_CONVERT_TIMINGS().
- This feature can be modified afterwards using unitary function @ref LL_I2C_SetTiming(). */
+ This feature can be modified afterwards using unitary function
+ @ref LL_I2C_SetTiming(). */
uint32_t AnalogFilter; /*!< Enables or disables analog noise filter.
This parameter can be a value of @ref I2C_LL_EC_ANALOGFILTER_SELECTION.
- This feature can be modified afterwards using unitary functions @ref LL_I2C_EnableAnalogFilter() or LL_I2C_DisableAnalogFilter(). */
+ This feature can be modified afterwards using unitary functions
+ @ref LL_I2C_EnableAnalogFilter() or LL_I2C_DisableAnalogFilter(). */
uint32_t DigitalFilter; /*!< Configures the digital noise filter.
This parameter can be a number between Min_Data = 0x00 and Max_Data = 0x0F.
- This feature can be modified afterwards using unitary function @ref LL_I2C_SetDigitalFilter(). */
+ This feature can be modified afterwards using unitary function
+ @ref LL_I2C_SetDigitalFilter(). */
uint32_t OwnAddress1; /*!< Specifies the device own address 1.
This parameter must be a value between Min_Data = 0x00 and Max_Data = 0x3FF.
- This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */
+ This feature can be modified afterwards using unitary function
+ @ref LL_I2C_SetOwnAddress1(). */
- uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte.
+ uint32_t TypeAcknowledge; /*!< Specifies the ACKnowledge or Non ACKnowledge condition after the address receive
+ match code or next received byte.
This parameter can be a value of @ref I2C_LL_EC_I2C_ACKNOWLEDGE.
- This feature can be modified afterwards using unitary function @ref LL_I2C_AcknowledgeNextData(). */
+ This feature can be modified afterwards using unitary function
+ @ref LL_I2C_AcknowledgeNextData(). */
uint32_t OwnAddrSize; /*!< Specifies the device own address 1 size (7-bit or 10-bit).
This parameter can be a value of @ref I2C_LL_EC_OWNADDRESS1.
- This feature can be modified afterwards using unitary function @ref LL_I2C_SetOwnAddress1(). */
+ This feature can be modified afterwards using unitary function
+ @ref LL_I2C_SetOwnAddress1(). */
} LL_I2C_InitTypeDef;
/**
* @}
@@ -170,10 +178,11 @@
/** @defgroup I2C_LL_EC_PERIPHERAL_MODE Peripheral Mode
* @{
*/
-#define LL_I2C_MODE_I2C 0x00000000U /*!< I2C Master or Slave mode */
-#define LL_I2C_MODE_SMBUS_HOST I2C_CR1_SMBHEN /*!< SMBus Host address acknowledge */
-#define LL_I2C_MODE_SMBUS_DEVICE 0x00000000U /*!< SMBus Device default mode (Default address not acknowledge) */
-#define LL_I2C_MODE_SMBUS_DEVICE_ARP I2C_CR1_SMBDEN /*!< SMBus Device Default address acknowledge */
+#define LL_I2C_MODE_I2C 0x00000000U /*!< I2C Master or Slave mode */
+#define LL_I2C_MODE_SMBUS_HOST I2C_CR1_SMBHEN /*!< SMBus Host address acknowledge */
+#define LL_I2C_MODE_SMBUS_DEVICE 0x00000000U /*!< SMBus Device default mode
+ (Default address not acknowledge) */
+#define LL_I2C_MODE_SMBUS_DEVICE_ARP I2C_CR1_SMBDEN /*!< SMBus Device Default address acknowledge */
/**
* @}
*/
@@ -208,14 +217,15 @@
/** @defgroup I2C_LL_EC_OWNADDRESS2 Own Address 2 Masks
* @{
*/
-#define LL_I2C_OWNADDRESS2_NOMASK I2C_OAR2_OA2NOMASK /*!< Own Address2 No mask. */
-#define LL_I2C_OWNADDRESS2_MASK01 I2C_OAR2_OA2MASK01 /*!< Only Address2 bits[7:2] are compared. */
-#define LL_I2C_OWNADDRESS2_MASK02 I2C_OAR2_OA2MASK02 /*!< Only Address2 bits[7:3] are compared. */
-#define LL_I2C_OWNADDRESS2_MASK03 I2C_OAR2_OA2MASK03 /*!< Only Address2 bits[7:4] are compared. */
-#define LL_I2C_OWNADDRESS2_MASK04 I2C_OAR2_OA2MASK04 /*!< Only Address2 bits[7:5] are compared. */
-#define LL_I2C_OWNADDRESS2_MASK05 I2C_OAR2_OA2MASK05 /*!< Only Address2 bits[7:6] are compared. */
-#define LL_I2C_OWNADDRESS2_MASK06 I2C_OAR2_OA2MASK06 /*!< Only Address2 bits[7] are compared. */
-#define LL_I2C_OWNADDRESS2_MASK07 I2C_OAR2_OA2MASK07 /*!< No comparison is done. All Address2 are acknowledged.*/
+#define LL_I2C_OWNADDRESS2_NOMASK I2C_OAR2_OA2NOMASK /*!< Own Address2 No mask. */
+#define LL_I2C_OWNADDRESS2_MASK01 I2C_OAR2_OA2MASK01 /*!< Only Address2 bits[7:2] are compared. */
+#define LL_I2C_OWNADDRESS2_MASK02 I2C_OAR2_OA2MASK02 /*!< Only Address2 bits[7:3] are compared. */
+#define LL_I2C_OWNADDRESS2_MASK03 I2C_OAR2_OA2MASK03 /*!< Only Address2 bits[7:4] are compared. */
+#define LL_I2C_OWNADDRESS2_MASK04 I2C_OAR2_OA2MASK04 /*!< Only Address2 bits[7:5] are compared. */
+#define LL_I2C_OWNADDRESS2_MASK05 I2C_OAR2_OA2MASK05 /*!< Only Address2 bits[7:6] are compared. */
+#define LL_I2C_OWNADDRESS2_MASK06 I2C_OAR2_OA2MASK06 /*!< Only Address2 bits[7] are compared. */
+#define LL_I2C_OWNADDRESS2_MASK07 I2C_OAR2_OA2MASK07 /*!< No comparison is done.
+ All Address2 are acknowledged. */
/**
* @}
*/
@@ -250,14 +260,21 @@
/** @defgroup I2C_LL_EC_MODE Transfer End Mode
* @{
*/
-#define LL_I2C_MODE_RELOAD I2C_CR2_RELOAD /*!< Enable I2C Reload mode. */
-#define LL_I2C_MODE_AUTOEND I2C_CR2_AUTOEND /*!< Enable I2C Automatic end mode with no HW PEC comparison. */
-#define LL_I2C_MODE_SOFTEND 0x00000000U /*!< Enable I2C Software end mode with no HW PEC comparison. */
-#define LL_I2C_MODE_SMBUS_RELOAD LL_I2C_MODE_RELOAD /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */
-#define LL_I2C_MODE_SMBUS_AUTOEND_NO_PEC LL_I2C_MODE_AUTOEND /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */
-#define LL_I2C_MODE_SMBUS_SOFTEND_NO_PEC LL_I2C_MODE_SOFTEND /*!< Enable SMBUS Software end mode with HW PEC comparison. */
-#define LL_I2C_MODE_SMBUS_AUTOEND_WITH_PEC (uint32_t)(LL_I2C_MODE_AUTOEND | I2C_CR2_PECBYTE) /*!< Enable SMBUS Automatic end mode with HW PEC comparison. */
-#define LL_I2C_MODE_SMBUS_SOFTEND_WITH_PEC (uint32_t)(LL_I2C_MODE_SOFTEND | I2C_CR2_PECBYTE) /*!< Enable SMBUS Software end mode with HW PEC comparison. */
+#define LL_I2C_MODE_RELOAD I2C_CR2_RELOAD /*!< Enable I2C Reload mode. */
+#define LL_I2C_MODE_AUTOEND I2C_CR2_AUTOEND /*!< Enable I2C Automatic end mode
+ with no HW PEC comparison. */
+#define LL_I2C_MODE_SOFTEND 0x00000000U /*!< Enable I2C Software end mode
+ with no HW PEC comparison. */
+#define LL_I2C_MODE_SMBUS_RELOAD LL_I2C_MODE_RELOAD /*!< Enable SMBUS Automatic end mode
+ with HW PEC comparison. */
+#define LL_I2C_MODE_SMBUS_AUTOEND_NO_PEC LL_I2C_MODE_AUTOEND /*!< Enable SMBUS Automatic end mode
+ with HW PEC comparison. */
+#define LL_I2C_MODE_SMBUS_SOFTEND_NO_PEC LL_I2C_MODE_SOFTEND /*!< Enable SMBUS Software end mode
+ with HW PEC comparison. */
+#define LL_I2C_MODE_SMBUS_AUTOEND_WITH_PEC (uint32_t)(LL_I2C_MODE_AUTOEND | I2C_CR2_PECBYTE)
+/*!< Enable SMBUS Automatic end mode with HW PEC comparison. */
+#define LL_I2C_MODE_SMBUS_SOFTEND_WITH_PEC (uint32_t)(LL_I2C_MODE_SOFTEND | I2C_CR2_PECBYTE)
+/*!< Enable SMBUS Software end mode with HW PEC comparison. */
/**
* @}
*/
@@ -265,14 +282,23 @@
/** @defgroup I2C_LL_EC_GENERATE Start And Stop Generation
* @{
*/
-#define LL_I2C_GENERATE_NOSTARTSTOP 0x00000000U /*!< Don't Generate Stop and Start condition. */
-#define LL_I2C_GENERATE_STOP (uint32_t)(0x80000000U | I2C_CR2_STOP) /*!< Generate Stop condition (Size should be set to 0). */
-#define LL_I2C_GENERATE_START_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN) /*!< Generate Start for read request. */
-#define LL_I2C_GENERATE_START_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Start for write request. */
-#define LL_I2C_GENERATE_RESTART_7BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN) /*!< Generate Restart for read request, slave 7Bit address. */
-#define LL_I2C_GENERATE_RESTART_7BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Restart for write request, slave 7Bit address. */
-#define LL_I2C_GENERATE_RESTART_10BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN | I2C_CR2_HEAD10R) /*!< Generate Restart for read request, slave 10Bit address. */
-#define LL_I2C_GENERATE_RESTART_10BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START) /*!< Generate Restart for write request, slave 10Bit address.*/
+#define LL_I2C_GENERATE_NOSTARTSTOP 0x00000000U
+/*!< Don't Generate Stop and Start condition. */
+#define LL_I2C_GENERATE_STOP (uint32_t)(0x80000000U | I2C_CR2_STOP)
+/*!< Generate Stop condition (Size should be set to 0). */
+#define LL_I2C_GENERATE_START_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN)
+/*!< Generate Start for read request. */
+#define LL_I2C_GENERATE_START_WRITE (uint32_t)(0x80000000U | I2C_CR2_START)
+/*!< Generate Start for write request. */
+#define LL_I2C_GENERATE_RESTART_7BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | I2C_CR2_RD_WRN)
+/*!< Generate Restart for read request, slave 7Bit address. */
+#define LL_I2C_GENERATE_RESTART_7BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START)
+/*!< Generate Restart for write request, slave 7Bit address. */
+#define LL_I2C_GENERATE_RESTART_10BIT_READ (uint32_t)(0x80000000U | I2C_CR2_START | \
+ I2C_CR2_RD_WRN | I2C_CR2_HEAD10R)
+/*!< Generate Restart for read request, slave 10Bit address. */
+#define LL_I2C_GENERATE_RESTART_10BIT_WRITE (uint32_t)(0x80000000U | I2C_CR2_START)
+/*!< Generate Restart for write request, slave 10Bit address.*/
/**
* @}
*/
@@ -280,8 +306,10 @@
/** @defgroup I2C_LL_EC_DIRECTION Read Write Direction
* @{
*/
-#define LL_I2C_DIRECTION_WRITE 0x00000000U /*!< Write transfer request by master, slave enters receiver mode. */
-#define LL_I2C_DIRECTION_READ I2C_ISR_DIR /*!< Read transfer request by master, slave enters transmitter mode.*/
+#define LL_I2C_DIRECTION_WRITE 0x00000000U /*!< Write transfer request by master,
+ slave enters receiver mode. */
+#define LL_I2C_DIRECTION_READ I2C_ISR_DIR /*!< Read transfer request by master,
+ slave enters transmitter mode.*/
/**
* @}
*/
@@ -289,8 +317,10 @@
/** @defgroup I2C_LL_EC_DMA_REG_DATA DMA Register Data
* @{
*/
-#define LL_I2C_DMA_REG_DATA_TRANSMIT 0x00000000U /*!< Get address of data register used for transmission */
-#define LL_I2C_DMA_REG_DATA_RECEIVE 0x00000001U /*!< Get address of data register used for reception */
+#define LL_I2C_DMA_REG_DATA_TRANSMIT 0x00000000U /*!< Get address of data register used for
+ transmission */
+#define LL_I2C_DMA_REG_DATA_RECEIVE 0x00000001U /*!< Get address of data register used for
+ reception */
/**
* @}
*/
@@ -298,8 +328,10 @@
/** @defgroup I2C_LL_EC_SMBUS_TIMEOUTA_MODE SMBus TimeoutA Mode SCL SDA Timeout
* @{
*/
-#define LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW 0x00000000U /*!< TimeoutA is used to detect SCL low level timeout. */
-#define LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH I2C_TIMEOUTR_TIDLE /*!< TimeoutA is used to detect both SCL and SDA high level timeout.*/
+#define LL_I2C_SMBUS_TIMEOUTA_MODE_SCL_LOW 0x00000000U /*!< TimeoutA is used to detect
+ SCL low level timeout. */
+#define LL_I2C_SMBUS_TIMEOUTA_MODE_SDA_SCL_HIGH I2C_TIMEOUTR_TIDLE /*!< TimeoutA is used to detect
+ both SCL and SDA high level timeout.*/
/**
* @}
*/
@@ -307,9 +339,12 @@
/** @defgroup I2C_LL_EC_SMBUS_TIMEOUT_SELECTION SMBus Timeout Selection
* @{
*/
-#define LL_I2C_SMBUS_TIMEOUTA I2C_TIMEOUTR_TIMOUTEN /*!< TimeoutA enable bit */
-#define LL_I2C_SMBUS_TIMEOUTB I2C_TIMEOUTR_TEXTEN /*!< TimeoutB (extended clock) enable bit */
-#define LL_I2C_SMBUS_ALL_TIMEOUT (uint32_t)(I2C_TIMEOUTR_TIMOUTEN | I2C_TIMEOUTR_TEXTEN) /*!< TimeoutA and TimeoutB (extended clock) enable bits */
+#define LL_I2C_SMBUS_TIMEOUTA I2C_TIMEOUTR_TIMOUTEN /*!< TimeoutA enable bit */
+#define LL_I2C_SMBUS_TIMEOUTB I2C_TIMEOUTR_TEXTEN /*!< TimeoutB (extended clock)
+ enable bit */
+#define LL_I2C_SMBUS_ALL_TIMEOUT (uint32_t)(I2C_TIMEOUTR_TIMOUTEN | \
+ I2C_TIMEOUTR_TEXTEN) /*!< TimeoutA and TimeoutB
+(extended clock) enable bits */
/**
* @}
*/
@@ -353,18 +388,22 @@
/**
* @brief Configure the SDA setup, hold time and the SCL high, low period.
* @param __PRESCALER__ This parameter must be a value between Min_Data=0 and Max_Data=0xF.
- * @param __DATA_SETUP_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. (tscldel = (SCLDEL+1)xtpresc)
- * @param __DATA_HOLD_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF. (tsdadel = SDADELxtpresc)
- * @param __CLOCK_HIGH_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF. (tsclh = (SCLH+1)xtpresc)
- * @param __CLOCK_LOW_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF. (tscll = (SCLL+1)xtpresc)
+ * @param __SETUP_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF.
+ (tscldel = (SCLDEL+1)xtpresc)
+ * @param __HOLD_TIME__ This parameter must be a value between Min_Data=0 and Max_Data=0xF.
+ (tsdadel = SDADELxtpresc)
+ * @param __SCLH_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF.
+ (tsclh = (SCLH+1)xtpresc)
+ * @param __SCLL_PERIOD__ This parameter must be a value between Min_Data=0 and Max_Data=0xFF.
+ (tscll = (SCLL+1)xtpresc)
* @retval Value between Min_Data=0 and Max_Data=0xFFFFFFFF
*/
-#define __LL_I2C_CONVERT_TIMINGS(__PRESCALER__, __DATA_SETUP_TIME__, __DATA_HOLD_TIME__, __CLOCK_HIGH_PERIOD__, __CLOCK_LOW_PERIOD__) \
- ((((uint32_t)(__PRESCALER__) << I2C_TIMINGR_PRESC_Pos) & I2C_TIMINGR_PRESC) | \
- (((uint32_t)(__DATA_SETUP_TIME__) << I2C_TIMINGR_SCLDEL_Pos) & I2C_TIMINGR_SCLDEL) | \
- (((uint32_t)(__DATA_HOLD_TIME__) << I2C_TIMINGR_SDADEL_Pos) & I2C_TIMINGR_SDADEL) | \
- (((uint32_t)(__CLOCK_HIGH_PERIOD__) << I2C_TIMINGR_SCLH_Pos) & I2C_TIMINGR_SCLH) | \
- (((uint32_t)(__CLOCK_LOW_PERIOD__) << I2C_TIMINGR_SCLL_Pos) & I2C_TIMINGR_SCLL))
+#define __LL_I2C_CONVERT_TIMINGS(__PRESCALER__, __SETUP_TIME__, __HOLD_TIME__, __SCLH_PERIOD__, __SCLL_PERIOD__) \
+ ((((uint32_t)(__PRESCALER__) << I2C_TIMINGR_PRESC_Pos) & I2C_TIMINGR_PRESC) | \
+ (((uint32_t)(__SETUP_TIME__) << I2C_TIMINGR_SCLDEL_Pos) & I2C_TIMINGR_SCLDEL) | \
+ (((uint32_t)(__HOLD_TIME__) << I2C_TIMINGR_SDADEL_Pos) & I2C_TIMINGR_SDADEL) | \
+ (((uint32_t)(__SCLH_PERIOD__) << I2C_TIMINGR_SCLH_Pos) & I2C_TIMINGR_SCLH) | \
+ (((uint32_t)(__SCLL_PERIOD__) << I2C_TIMINGR_SCLL_Pos) & I2C_TIMINGR_SCLL))
/**
* @}
*/
@@ -428,7 +467,8 @@
* @param AnalogFilter This parameter can be one of the following values:
* @arg @ref LL_I2C_ANALOGFILTER_ENABLE
* @arg @ref LL_I2C_ANALOGFILTER_DISABLE
- * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled) and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk).
+ * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled)
+ and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk).
* This parameter is used to configure the digital noise filter on SDA and SCL input.
* The digital filter will filter spikes with a length of up to DNF[3:0]*ti2cclk.
* @retval None
@@ -444,7 +484,8 @@
* This filter can only be programmed when the I2C is disabled (PE = 0).
* @rmtoll CR1 DNF LL_I2C_SetDigitalFilter
* @param I2Cx I2C Instance.
- * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled) and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk).
+ * @param DigitalFilter This parameter must be a value between Min_Data=0x00 (Digital filter disabled)
+ and Max_Data=0x0F (Digital filter enabled and filtering capability up to 15*ti2cclk).
* This parameter is used to configure the digital noise filter on SDA and SCL input.
* The digital filter will filter spikes with a length of up to DNF[3:0]*ti2cclk.
* @retval None
@@ -664,7 +705,7 @@
/**
* @brief Enable Wakeup from STOP.
- * @note Macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not
* WakeUpFromStop feature is supported by the I2Cx Instance.
* @note This bit can only be programmed when Digital Filter is disabled.
* @rmtoll CR1 WUPEN LL_I2C_EnableWakeUpFromStop
@@ -678,7 +719,7 @@
/**
* @brief Disable Wakeup from STOP.
- * @note Macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not
* WakeUpFromStop feature is supported by the I2Cx Instance.
* @rmtoll CR1 WUPEN LL_I2C_DisableWakeUpFromStop
* @param I2Cx I2C Instance.
@@ -691,7 +732,7 @@
/**
* @brief Check if Wakeup from STOP is enabled or disabled.
- * @note Macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_I2C_WAKEUP_FROMSTOP_INSTANCE(I2Cx) can be used to check whether or not
* WakeUpFromStop feature is supported by the I2Cx Instance.
* @rmtoll CR1 WUPEN LL_I2C_IsEnabledWakeUpFromStop
* @param I2Cx I2C Instance.
@@ -941,7 +982,7 @@
/**
* @brief Configure peripheral mode.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 SMBHEN LL_I2C_SetMode\n
* CR1 SMBDEN LL_I2C_SetMode
@@ -960,7 +1001,7 @@
/**
* @brief Get peripheral mode.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 SMBHEN LL_I2C_GetMode\n
* CR1 SMBDEN LL_I2C_GetMode
@@ -978,7 +1019,7 @@
/**
* @brief Enable SMBus alert (Host or Device mode)
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note SMBus Device mode:
* - SMBus Alert pin is drived low and
@@ -996,7 +1037,7 @@
/**
* @brief Disable SMBus alert (Host or Device mode)
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note SMBus Device mode:
* - SMBus Alert pin is not drived (can be used as a standard GPIO) and
@@ -1014,7 +1055,7 @@
/**
* @brief Check if SMBus alert (Host or Device mode) is enabled or disabled.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 ALERTEN LL_I2C_IsEnabledSMBusAlert
* @param I2Cx I2C Instance.
@@ -1027,7 +1068,7 @@
/**
* @brief Enable SMBus Packet Error Calculation (PEC).
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 PECEN LL_I2C_EnableSMBusPEC
* @param I2Cx I2C Instance.
@@ -1040,7 +1081,7 @@
/**
* @brief Disable SMBus Packet Error Calculation (PEC).
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 PECEN LL_I2C_DisableSMBusPEC
* @param I2Cx I2C Instance.
@@ -1053,7 +1094,7 @@
/**
* @brief Check if SMBus Packet Error Calculation (PEC) is enabled or disabled.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR1 PECEN LL_I2C_IsEnabledSMBusPEC
* @param I2Cx I2C Instance.
@@ -1066,7 +1107,7 @@
/**
* @brief Configure the SMBus Clock Timeout.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note This configuration can only be programmed when associated Timeout is disabled (TimeoutA and/orTimeoutB).
* @rmtoll TIMEOUTR TIMEOUTA LL_I2C_ConfigSMBusTimeout\n
@@ -1089,7 +1130,7 @@
/**
* @brief Configure the SMBus Clock TimeoutA (SCL low timeout or SCL and SDA high timeout depends on TimeoutA mode).
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note These bits can only be programmed when TimeoutA is disabled.
* @rmtoll TIMEOUTR TIMEOUTA LL_I2C_SetSMBusTimeoutA
@@ -1104,7 +1145,7 @@
/**
* @brief Get the SMBus Clock TimeoutA setting.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll TIMEOUTR TIMEOUTA LL_I2C_GetSMBusTimeoutA
* @param I2Cx I2C Instance.
@@ -1117,7 +1158,7 @@
/**
* @brief Set the SMBus Clock TimeoutA mode.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note This bit can only be programmed when TimeoutA is disabled.
* @rmtoll TIMEOUTR TIDLE LL_I2C_SetSMBusTimeoutAMode
@@ -1134,7 +1175,7 @@
/**
* @brief Get the SMBus Clock TimeoutA mode.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll TIMEOUTR TIDLE LL_I2C_GetSMBusTimeoutAMode
* @param I2Cx I2C Instance.
@@ -1149,7 +1190,7 @@
/**
* @brief Configure the SMBus Extended Cumulative Clock TimeoutB (Master or Slave mode).
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note These bits can only be programmed when TimeoutB is disabled.
* @rmtoll TIMEOUTR TIMEOUTB LL_I2C_SetSMBusTimeoutB
@@ -1164,7 +1205,7 @@
/**
* @brief Get the SMBus Extended Cumulative Clock TimeoutB setting.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll TIMEOUTR TIMEOUTB LL_I2C_GetSMBusTimeoutB
* @param I2Cx I2C Instance.
@@ -1177,7 +1218,7 @@
/**
* @brief Enable the SMBus Clock Timeout.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll TIMEOUTR TIMOUTEN LL_I2C_EnableSMBusTimeout\n
* TIMEOUTR TEXTEN LL_I2C_EnableSMBusTimeout
@@ -1195,7 +1236,7 @@
/**
* @brief Disable the SMBus Clock Timeout.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll TIMEOUTR TIMOUTEN LL_I2C_DisableSMBusTimeout\n
* TIMEOUTR TEXTEN LL_I2C_DisableSMBusTimeout
@@ -1213,7 +1254,7 @@
/**
* @brief Check if the SMBus Clock Timeout is enabled or disabled.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll TIMEOUTR TIMOUTEN LL_I2C_IsEnabledSMBusTimeout\n
* TIMEOUTR TEXTEN LL_I2C_IsEnabledSMBusTimeout
@@ -1226,7 +1267,8 @@
*/
__STATIC_INLINE uint32_t LL_I2C_IsEnabledSMBusTimeout(I2C_TypeDef *I2Cx, uint32_t ClockTimeout)
{
- return ((READ_BIT(I2Cx->TIMEOUTR, (I2C_TIMEOUTR_TIMOUTEN | I2C_TIMEOUTR_TEXTEN)) == (ClockTimeout)) ? 1UL : 0UL);
+ return ((READ_BIT(I2Cx->TIMEOUTR, (I2C_TIMEOUTR_TIMOUTEN | I2C_TIMEOUTR_TEXTEN)) == \
+ (ClockTimeout)) ? 1UL : 0UL);
}
/**
@@ -1443,7 +1485,7 @@
/**
* @brief Enable Error interrupts.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note Any of these errors will generate interrupt :
* Arbitration Loss (ARLO)
@@ -1463,7 +1505,7 @@
/**
* @brief Disable Error interrupts.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note Any of these errors will generate interrupt :
* Arbitration Loss (ARLO)
@@ -1645,7 +1687,7 @@
/**
* @brief Indicate the status of SMBus PEC error flag in reception.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note RESET: Clear default value.
* SET: When the received PEC does not match with the PEC register content.
@@ -1660,7 +1702,7 @@
/**
* @brief Indicate the status of SMBus Timeout detection flag.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note RESET: Clear default value.
* SET: When a timeout or extended clock timeout occurs.
@@ -1675,7 +1717,7 @@
/**
* @brief Indicate the status of SMBus alert flag.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @note RESET: Clear default value.
* SET: When SMBus host configuration, SMBus alert enabled and
@@ -1782,7 +1824,7 @@
/**
* @brief Clear SMBus PEC error flag.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll ICR PECCF LL_I2C_ClearSMBusFlag_PECERR
* @param I2Cx I2C Instance.
@@ -1795,7 +1837,7 @@
/**
* @brief Clear SMBus Timeout detection flag.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll ICR TIMOUTCF LL_I2C_ClearSMBusFlag_TIMEOUT
* @param I2Cx I2C Instance.
@@ -1808,7 +1850,7 @@
/**
* @brief Clear SMBus Alert flag.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll ICR ALERTCF LL_I2C_ClearSMBusFlag_ALERT
* @param I2Cx I2C Instance.
@@ -1923,7 +1965,8 @@
}
/**
- * @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code or next received byte.
+ * @brief Prepare the generation of a ACKnowledge or Non ACKnowledge condition after the address receive match code
+ or next received byte.
* @note Usage in Slave mode only.
* @rmtoll CR2 NACK LL_I2C_AcknowledgeNextData
* @param I2Cx I2C Instance.
@@ -1964,7 +2007,8 @@
/**
* @brief Enable automatic RESTART Read request condition for 10bit address header (master mode).
* @note The master sends the complete 10bit slave address read sequence :
- * Start + 2 bytes 10bit address in Write direction + Restart + first 7 bits of 10bit address in Read direction.
+ * Start + 2 bytes 10bit address in Write direction + Restart + first 7 bits of 10bit address
+ in Read direction.
* @rmtoll CR2 HEAD10R LL_I2C_EnableAuto10BitRead
* @param I2Cx I2C Instance.
* @retval None
@@ -2125,9 +2169,10 @@
/**
* @brief Enable internal comparison of the SMBus Packet Error byte (transmission or reception mode).
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
- * @note This feature is cleared by hardware when the PEC byte is transferred, or when a STOP condition or an Address Matched is received.
+ * @note This feature is cleared by hardware when the PEC byte is transferred, or when a STOP condition
+ or an Address Matched is received.
* This bit has no effect when RELOAD bit is set.
* This bit has no effect in device mode when SBC bit is not set.
* @rmtoll CR2 PECBYTE LL_I2C_EnableSMBusPECCompare
@@ -2141,7 +2186,7 @@
/**
* @brief Check if the SMBus Packet Error byte internal comparison is requested or not.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll CR2 PECBYTE LL_I2C_IsEnabledSMBusPECCompare
* @param I2Cx I2C Instance.
@@ -2154,7 +2199,7 @@
/**
* @brief Get the SMBus Packet Error byte calculated.
- * @note Macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
+ * @note The macro IS_SMBUS_ALL_INSTANCE(I2Cx) can be used to check whether or not
* SMBus feature is supported by the I2Cx Instance.
* @rmtoll PECR PEC LL_I2C_GetSMBusPEC
* @param I2Cx I2C Instance.
diff --git a/Inc/stm32wlxx_ll_iwdg.h b/Inc/stm32wlxx_ll_iwdg.h
index e3d3093..dc43d8f 100644
--- a/Inc/stm32wlxx_ll_iwdg.h
+++ b/Inc/stm32wlxx_ll_iwdg.h
@@ -304,8 +304,8 @@
/**
* @brief Check if all flags Prescaler, Reload & Window Value Update are reset or not
* @rmtoll SR PVU LL_IWDG_IsReady\n
- * SR WVU LL_IWDG_IsReady\n
- * SR RVU LL_IWDG_IsReady
+ * SR RVU LL_IWDG_IsReady\n
+ * SR WVU LL_IWDG_IsReady
* @param IWDGx IWDG Instance
* @retval State of bits (1 or 0).
*/
@@ -318,7 +318,6 @@
* @}
*/
-
/**
* @}
*/
diff --git a/Inc/stm32wlxx_ll_lpuart.h b/Inc/stm32wlxx_ll_lpuart.h
index 493a3f2..013c67d 100644
--- a/Inc/stm32wlxx_ll_lpuart.h
+++ b/Inc/stm32wlxx_ll_lpuart.h
@@ -559,7 +559,7 @@
*/
__STATIC_INLINE void LL_LPUART_SetTXFIFOThreshold(USART_TypeDef *LPUARTx, uint32_t Threshold)
{
- MODIFY_REG(LPUARTx->CR3, USART_CR3_TXFTCFG, Threshold << USART_CR3_TXFTCFG_Pos);
+ ATOMIC_MODIFY_REG(LPUARTx->CR3, USART_CR3_TXFTCFG, Threshold << USART_CR3_TXFTCFG_Pos);
}
/**
@@ -594,7 +594,7 @@
*/
__STATIC_INLINE void LL_LPUART_SetRXFIFOThreshold(USART_TypeDef *LPUARTx, uint32_t Threshold)
{
- MODIFY_REG(LPUARTx->CR3, USART_CR3_RXFTCFG, Threshold << USART_CR3_RXFTCFG_Pos);
+ ATOMIC_MODIFY_REG(LPUARTx->CR3, USART_CR3_RXFTCFG, Threshold << USART_CR3_RXFTCFG_Pos);
}
/**
@@ -637,8 +637,8 @@
*/
__STATIC_INLINE void LL_LPUART_ConfigFIFOsThreshold(USART_TypeDef *LPUARTx, uint32_t TXThreshold, uint32_t RXThreshold)
{
- MODIFY_REG(LPUARTx->CR3, USART_CR3_TXFTCFG | USART_CR3_RXFTCFG, (TXThreshold << USART_CR3_TXFTCFG_Pos) | \
- (RXThreshold << USART_CR3_RXFTCFG_Pos));
+ ATOMIC_MODIFY_REG(LPUARTx->CR3, USART_CR3_TXFTCFG | USART_CR3_RXFTCFG, (TXThreshold << USART_CR3_TXFTCFG_Pos) | \
+ (RXThreshold << USART_CR3_RXFTCFG_Pos));
}
/**
@@ -651,7 +651,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableInStopMode(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_UESM);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_UESM);
}
/**
@@ -663,7 +663,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableInStopMode(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_UESM);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_UESM);
}
/**
@@ -686,7 +686,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableDirectionRx(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_RE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RE);
}
/**
@@ -697,7 +697,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableDirectionRx(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_RE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RE);
}
/**
@@ -708,7 +708,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableDirectionTx(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_TE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TE);
}
/**
@@ -719,7 +719,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableDirectionTx(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_TE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TE);
}
/**
@@ -737,7 +737,7 @@
*/
__STATIC_INLINE void LL_LPUART_SetTransferDirection(USART_TypeDef *LPUARTx, uint32_t TransferDirection)
{
- MODIFY_REG(LPUARTx->CR1, USART_CR1_RE | USART_CR1_TE, TransferDirection);
+ ATOMIC_MODIFY_REG(LPUARTx->CR1, USART_CR1_RE | USART_CR1_TE, TransferDirection);
}
/**
@@ -854,7 +854,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableMuteMode(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_MME);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_MME);
}
/**
@@ -865,7 +865,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableMuteMode(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_MME);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_MME);
}
/**
@@ -1928,7 +1928,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_IDLE(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_IDLEIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_IDLEIE);
}
/* Legacy define */
@@ -1942,7 +1942,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_RXNE_RXFNE(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
}
/**
@@ -1953,7 +1953,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_TC(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TCIE);
}
/* Legacy define */
@@ -1967,7 +1967,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_TXE_TXFNF(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
}
/**
@@ -1978,7 +1978,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_PE(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_PEIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_PEIE);
}
/**
@@ -1989,7 +1989,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_CM(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_CMIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_CMIE);
}
/**
@@ -2000,7 +2000,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_TXFE(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_TXFEIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_TXFEIE);
}
/**
@@ -2011,7 +2011,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_RXFF(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR1, USART_CR1_RXFFIE);
+ ATOMIC_SET_BIT(LPUARTx->CR1, USART_CR1_RXFFIE);
}
/**
@@ -2026,7 +2026,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_ERROR(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_EIE);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_EIE);
}
/**
@@ -2037,7 +2037,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_CTS(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_CTSIE);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_CTSIE);
}
/**
@@ -2048,7 +2048,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_WKUP(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_WUFIE);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_WUFIE);
}
/**
@@ -2059,7 +2059,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_TXFT(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_TXFTIE);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_TXFTIE);
}
/**
@@ -2070,7 +2070,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableIT_RXFT(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_RXFTIE);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_RXFTIE);
}
/**
@@ -2081,7 +2081,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_IDLE(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_IDLEIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_IDLEIE);
}
/* Legacy define */
@@ -2095,7 +2095,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_RXNE_RXFNE(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
}
/**
@@ -2106,7 +2106,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_TC(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_TCIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TCIE);
}
/* Legacy define */
@@ -2120,7 +2120,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_TXE_TXFNF(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
}
/**
@@ -2131,7 +2131,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_PE(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_PEIE);
}
/**
@@ -2142,7 +2142,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_CM(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_CMIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_CMIE);
}
/**
@@ -2153,7 +2153,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_TXFE(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXFEIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_TXFEIE);
}
/**
@@ -2164,7 +2164,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_RXFF(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXFFIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR1, USART_CR1_RXFFIE);
}
/**
@@ -2179,7 +2179,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_ERROR(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_EIE);
}
/**
@@ -2190,7 +2190,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_CTS(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_CTSIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_CTSIE);
}
/**
@@ -2201,7 +2201,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_WKUP(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_WUFIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_WUFIE);
}
/**
@@ -2212,7 +2212,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_TXFT(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_TXFTIE);
}
/**
@@ -2223,7 +2223,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableIT_RXFT(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_RXFTIE);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_RXFTIE);
}
/**
@@ -2391,7 +2391,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableDMAReq_RX(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_DMAR);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_DMAR);
}
/**
@@ -2402,7 +2402,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableDMAReq_RX(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_DMAR);
}
/**
@@ -2424,7 +2424,7 @@
*/
__STATIC_INLINE void LL_LPUART_EnableDMAReq_TX(USART_TypeDef *LPUARTx)
{
- SET_BIT(LPUARTx->CR3, USART_CR3_DMAT);
+ ATOMIC_SET_BIT(LPUARTx->CR3, USART_CR3_DMAT);
}
/**
@@ -2435,7 +2435,7 @@
*/
__STATIC_INLINE void LL_LPUART_DisableDMAReq_TX(USART_TypeDef *LPUARTx)
{
- CLEAR_BIT(LPUARTx->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(LPUARTx->CR3, USART_CR3_DMAT);
}
/**
diff --git a/Inc/stm32wlxx_ll_spi.h b/Inc/stm32wlxx_ll_spi.h
index 0765aed..3e04ef1 100644
--- a/Inc/stm32wlxx_ll_spi.h
+++ b/Inc/stm32wlxx_ll_spi.h
@@ -1333,7 +1333,7 @@
*/
__STATIC_INLINE uint8_t LL_SPI_ReceiveData8(SPI_TypeDef *SPIx)
{
- return (uint8_t)(READ_REG(SPIx->DR));
+ return (*((__IO uint8_t *)&SPIx->DR));
}
/**
diff --git a/Inc/stm32wlxx_ll_tim.h b/Inc/stm32wlxx_ll_tim.h
index 1aefeb7..649049a 100644
--- a/Inc/stm32wlxx_ll_tim.h
+++ b/Inc/stm32wlxx_ll_tim.h
@@ -598,8 +598,8 @@
/** @defgroup TIM_LL_EC_ONEPULSEMODE One Pulse Mode
* @{
*/
-#define LL_TIM_ONEPULSEMODE_SINGLE TIM_CR1_OPM /*!< Counter is not stopped at update event */
-#define LL_TIM_ONEPULSEMODE_REPETITIVE 0x00000000U /*!< Counter stops counting at the next update event */
+#define LL_TIM_ONEPULSEMODE_SINGLE TIM_CR1_OPM /*!< Counter stops counting at the next update event */
+#define LL_TIM_ONEPULSEMODE_REPETITIVE 0x00000000U /*!< Counter is not stopped at update event */
/**
* @}
*/
@@ -1515,7 +1515,16 @@
*/
__STATIC_INLINE uint32_t LL_TIM_GetCounterMode(TIM_TypeDef *TIMx)
{
- return (uint32_t)(READ_BIT(TIMx->CR1, TIM_CR1_DIR | TIM_CR1_CMS));
+ uint32_t counter_mode;
+
+ counter_mode = (uint32_t)(READ_BIT(TIMx->CR1, TIM_CR1_CMS));
+
+ if (counter_mode == 0U)
+ {
+ counter_mode = (uint32_t)(READ_BIT(TIMx->CR1, TIM_CR1_DIR));
+ }
+
+ return counter_mode;
}
/**
diff --git a/Inc/stm32wlxx_ll_usart.h b/Inc/stm32wlxx_ll_usart.h
index de04ac3..830b0ad 100644
--- a/Inc/stm32wlxx_ll_usart.h
+++ b/Inc/stm32wlxx_ll_usart.h
@@ -88,41 +88,49 @@
uint32_t PrescalerValue; /*!< Specifies the Prescaler to compute the communication baud rate.
This parameter can be a value of @ref USART_LL_EC_PRESCALER.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetPrescaler().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetPrescaler().*/
uint32_t BaudRate; /*!< This field defines expected Usart communication baud rate.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetBaudRate().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetBaudRate().*/
uint32_t DataWidth; /*!< Specifies the number of data bits transmitted or received in a frame.
This parameter can be a value of @ref USART_LL_EC_DATAWIDTH.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetDataWidth().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetDataWidth().*/
uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
This parameter can be a value of @ref USART_LL_EC_STOPBITS.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetStopBitsLength().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetStopBitsLength().*/
uint32_t Parity; /*!< Specifies the parity mode.
This parameter can be a value of @ref USART_LL_EC_PARITY.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetParity().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetParity().*/
uint32_t TransferDirection; /*!< Specifies whether the Receive and/or Transmit mode is enabled or disabled.
This parameter can be a value of @ref USART_LL_EC_DIRECTION.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetTransferDirection().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetTransferDirection().*/
uint32_t HardwareFlowControl; /*!< Specifies whether the hardware flow control mode is enabled or disabled.
This parameter can be a value of @ref USART_LL_EC_HWCONTROL.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetHWFlowCtrl().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetHWFlowCtrl().*/
uint32_t OverSampling; /*!< Specifies whether USART oversampling mode is 16 or 8.
This parameter can be a value of @ref USART_LL_EC_OVERSAMPLING.
- This feature can be modified afterwards using unitary function @ref LL_USART_SetOverSampling().*/
+ This feature can be modified afterwards using unitary
+ function @ref LL_USART_SetOverSampling().*/
} LL_USART_InitTypeDef;
@@ -141,20 +149,23 @@
uint32_t ClockPolarity; /*!< Specifies the steady state of the serial clock.
This parameter can be a value of @ref USART_LL_EC_POLARITY.
- USART HW configuration can be modified afterwards using unitary functions @ref LL_USART_SetClockPolarity().
+ USART HW configuration can be modified afterwards using unitary
+ functions @ref LL_USART_SetClockPolarity().
For more details, refer to description of this function. */
uint32_t ClockPhase; /*!< Specifies the clock transition on which the bit capture is made.
This parameter can be a value of @ref USART_LL_EC_PHASE.
- USART HW configuration can be modified afterwards using unitary functions @ref LL_USART_SetClockPhase().
+ USART HW configuration can be modified afterwards using unitary
+ functions @ref LL_USART_SetClockPhase().
For more details, refer to description of this function. */
uint32_t LastBitClockPulse; /*!< Specifies whether the clock pulse corresponding to the last transmitted
data bit (MSB) has to be output on the SCLK pin in synchronous mode.
This parameter can be a value of @ref USART_LL_EC_LASTCLKPULSE.
- USART HW configuration can be modified afterwards using unitary functions @ref LL_USART_SetLastClkPulseOutput().
+ USART HW configuration can be modified afterwards using unitary
+ functions @ref LL_USART_SetLastClkPulseOutput().
For more details, refer to description of this function. */
} LL_USART_ClockInitTypeDef;
@@ -699,7 +710,7 @@
*/
__STATIC_INLINE void LL_USART_SetTXFIFOThreshold(USART_TypeDef *USARTx, uint32_t Threshold)
{
- MODIFY_REG(USARTx->CR3, USART_CR3_TXFTCFG, Threshold << USART_CR3_TXFTCFG_Pos);
+ ATOMIC_MODIFY_REG(USARTx->CR3, USART_CR3_TXFTCFG, Threshold << USART_CR3_TXFTCFG_Pos);
}
/**
@@ -738,7 +749,7 @@
*/
__STATIC_INLINE void LL_USART_SetRXFIFOThreshold(USART_TypeDef *USARTx, uint32_t Threshold)
{
- MODIFY_REG(USARTx->CR3, USART_CR3_RXFTCFG, Threshold << USART_CR3_RXFTCFG_Pos);
+ ATOMIC_MODIFY_REG(USARTx->CR3, USART_CR3_RXFTCFG, Threshold << USART_CR3_RXFTCFG_Pos);
}
/**
@@ -785,7 +796,8 @@
*/
__STATIC_INLINE void LL_USART_ConfigFIFOsThreshold(USART_TypeDef *USARTx, uint32_t TXThreshold, uint32_t RXThreshold)
{
- MODIFY_REG(USARTx->CR3, USART_CR3_TXFTCFG | USART_CR3_RXFTCFG, (TXThreshold << USART_CR3_TXFTCFG_Pos) | (RXThreshold << USART_CR3_RXFTCFG_Pos));
+ ATOMIC_MODIFY_REG(USARTx->CR3, USART_CR3_TXFTCFG | USART_CR3_RXFTCFG,
+ (TXThreshold << USART_CR3_TXFTCFG_Pos) | (RXThreshold << USART_CR3_RXFTCFG_Pos));
}
/**
@@ -800,7 +812,7 @@
*/
__STATIC_INLINE void LL_USART_EnableInStopMode(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_UESM);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_UESM);
}
/**
@@ -814,7 +826,7 @@
*/
__STATIC_INLINE void LL_USART_DisableInStopMode(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_UESM);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_UESM);
}
/**
@@ -838,7 +850,7 @@
*/
__STATIC_INLINE void LL_USART_EnableDirectionRx(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_RE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_RE);
}
/**
@@ -849,7 +861,7 @@
*/
__STATIC_INLINE void LL_USART_DisableDirectionRx(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_RE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_RE);
}
/**
@@ -860,7 +872,7 @@
*/
__STATIC_INLINE void LL_USART_EnableDirectionTx(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_TE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TE);
}
/**
@@ -871,7 +883,7 @@
*/
__STATIC_INLINE void LL_USART_DisableDirectionTx(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_TE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TE);
}
/**
@@ -889,7 +901,7 @@
*/
__STATIC_INLINE void LL_USART_SetTransferDirection(USART_TypeDef *USARTx, uint32_t TransferDirection)
{
- MODIFY_REG(USARTx->CR1, USART_CR1_RE | USART_CR1_TE, TransferDirection);
+ ATOMIC_MODIFY_REG(USARTx->CR1, USART_CR1_RE | USART_CR1_TE, TransferDirection);
}
/**
@@ -1008,7 +1020,7 @@
*/
__STATIC_INLINE void LL_USART_EnableMuteMode(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_MME);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_MME);
}
/**
@@ -1019,7 +1031,7 @@
*/
__STATIC_INLINE void LL_USART_DisableMuteMode(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_MME);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_MME);
}
/**
@@ -1870,6 +1882,10 @@
{
/* Do not overstep the size of USART_PRESCALER_TAB */
}
+ else if (BaudRate == 0U)
+ {
+ /* Can Not divide per 0 */
+ }
else if (OverSampling == LL_USART_OVERSAMPLING_8)
{
usartdiv = (uint16_t)(__LL_USART_DIV_SAMPLING8(PeriphClk, (uint8_t)PrescalerValue, BaudRate));
@@ -3434,7 +3450,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_IDLE(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_IDLEIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_IDLEIE);
}
/* Legacy define */
@@ -3450,7 +3466,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_RXNE_RXFNE(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
}
/**
@@ -3461,7 +3477,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_TC(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TCIE);
}
/* Legacy define */
@@ -3477,7 +3493,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_TXE_TXFNF(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
}
/**
@@ -3488,7 +3504,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_PE(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_PEIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_PEIE);
}
/**
@@ -3499,7 +3515,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_CM(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_CMIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_CMIE);
}
/**
@@ -3510,7 +3526,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_RTO(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_RTOIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_RTOIE);
}
/**
@@ -3523,7 +3539,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_EOB(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_EOBIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_EOBIE);
}
/**
@@ -3536,7 +3552,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_TXFE(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_TXFEIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TXFEIE);
}
/**
@@ -3547,7 +3563,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_RXFF(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR1, USART_CR1_RXFFIE);
+ ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_RXFFIE);
}
/**
@@ -3575,7 +3591,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_ERROR(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_EIE);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_EIE);
}
/**
@@ -3588,7 +3604,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_CTS(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_CTSIE);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_CTSIE);
}
/**
@@ -3601,7 +3617,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_WKUP(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_WUFIE);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_WUFIE);
}
/**
@@ -3614,7 +3630,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_TXFT(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_TXFTIE);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_TXFTIE);
}
/**
@@ -3627,7 +3643,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_TCBGT(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_TCBGTIE);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_TCBGTIE);
}
/**
@@ -3640,7 +3656,7 @@
*/
__STATIC_INLINE void LL_USART_EnableIT_RXFT(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_RXFTIE);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_RXFTIE);
}
/**
@@ -3651,7 +3667,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_IDLE(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_IDLEIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_IDLEIE);
}
/* Legacy define */
@@ -3667,7 +3683,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_RXNE_RXFNE(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_RXNEIE_RXFNEIE);
}
/**
@@ -3678,7 +3694,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_TC(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_TCIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TCIE);
}
/* Legacy define */
@@ -3694,7 +3710,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_TXE_TXFNF(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TXEIE_TXFNFIE);
}
/**
@@ -3705,7 +3721,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_PE(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_PEIE);
}
/**
@@ -3716,7 +3732,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_CM(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_CMIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_CMIE);
}
/**
@@ -3727,7 +3743,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_RTO(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_RTOIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_RTOIE);
}
/**
@@ -3740,7 +3756,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_EOB(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_EOBIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_EOBIE);
}
/**
@@ -3753,7 +3769,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_TXFE(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_TXFEIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TXFEIE);
}
/**
@@ -3766,7 +3782,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_RXFF(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR1, USART_CR1_RXFFIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_RXFFIE);
}
/**
@@ -3794,7 +3810,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_ERROR(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_EIE);
}
/**
@@ -3807,7 +3823,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_CTS(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_CTSIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_CTSIE);
}
/**
@@ -3820,7 +3836,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_WKUP(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_WUFIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_WUFIE);
}
/**
@@ -3833,7 +3849,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_TXFT(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_TXFTIE);
}
/**
@@ -3846,7 +3862,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_TCBGT(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_TCBGTIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_TCBGTIE);
}
/**
@@ -3859,7 +3875,7 @@
*/
__STATIC_INLINE void LL_USART_DisableIT_RXFT(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_RXFTIE);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_RXFTIE);
}
/**
@@ -4093,7 +4109,7 @@
*/
__STATIC_INLINE void LL_USART_EnableDMAReq_RX(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_DMAR);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_DMAR);
}
/**
@@ -4104,7 +4120,7 @@
*/
__STATIC_INLINE void LL_USART_DisableDMAReq_RX(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_DMAR);
}
/**
@@ -4126,7 +4142,7 @@
*/
__STATIC_INLINE void LL_USART_EnableDMAReq_TX(USART_TypeDef *USARTx)
{
- SET_BIT(USARTx->CR3, USART_CR3_DMAT);
+ ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_DMAT);
}
/**
@@ -4137,7 +4153,7 @@
*/
__STATIC_INLINE void LL_USART_DisableDMAReq_TX(USART_TypeDef *USARTx)
{
- CLEAR_BIT(USARTx->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_DMAT);
}
/**
diff --git a/LICENSE.md b/LICENSE.md
new file mode 100644
index 0000000..efd2b1f
--- /dev/null
+++ b/LICENSE.md
@@ -0,0 +1,27 @@
+Copyright 2020 STMicroelectronics.
+All rights reserved.
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+
+1. Redistributions of source code must retain the above copyright notice, this
+list of conditions and the following disclaimer.
+
+2. Redistributions in binary form must reproduce the above copyright notice,
+this list of conditions and the following disclaimer in the documentation and/or
+other materials provided with the distribution.
+
+3. Neither the name of the copyright holder nor the names of its contributors
+may be used to endorse or promote products derived from this software without
+specific prior written permission.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
+ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
\ No newline at end of file
diff --git a/License.md b/License.md
deleted file mode 100644
index c6b7c8b..0000000
--- a/License.md
+++ /dev/null
@@ -1,3 +0,0 @@
-# Copyright (c) 2020 STMicroelectronics
-
-This software component is licensed by STMicroelectronics under the **BSD-3-Clause** license. You may not use this software except in compliance with this license. You may obtain a copy of the license [here](https://opensource.org/licenses/BSD-3-Clause).
\ No newline at end of file
diff --git a/README.md b/README.md
index d592d35..a663bfd 100644
--- a/README.md
+++ b/README.md
@@ -1,14 +1,16 @@
# STM32CubeWL HAL Driver MCU Component
+
+
## Overview
-**STM32Cube** is an STMicroelectronics original initiative to ease the developers life by reducing efforts, time and cost.
+**STM32Cube** is an STMicroelectronics original initiative to ease developers' life by reducing efforts, time and cost.
**STM32Cube** covers the overall STM32 products portfolio. It includes a comprehensive embedded software platform delivered for each STM32 series.
* The CMSIS modules (core and device) corresponding to the ARM(tm) core implemented in this STM32 product.
* The STM32 HAL-LL drivers, an abstraction layer offering a set of APIs ensuring maximized portability across the STM32 portfolio.
* The BSP drivers of each evaluation, demonstration or nucleo board provided for this STM32 series.
- * A consistent set of middleware components such as RTOS, USB, FatFS, graphics, touch sensing library...
+ * A consistent set of middleware libraries such as RTOS, USB, FatFS, graphics, touch sensing library...
* A full set of software projects (basic examples, applications, and demonstrations) for each board provided for this STM32 series.
Two models of publication are proposed for the STM32Cube embedded software:
@@ -28,23 +30,25 @@
## Release note
-Details about the content of this release are available in the release note [here](https://htmlpreview.github.io/?https://github.com/STMicroelectronics/stm32wlxx_hal_driver/blob/main/Release_Notes.html).
+Details about the content of this release are available in the release note [here](https://htmlpreview.github.io/?https://github.com/STMicroelectronics/stm32wlxx_hal_driver/blob/master/Release_Notes.html).
## Compatibility information
-In this table, you can find the successive versions of this HAL-LL Driver component, in line with the corresponding versions of the full MCU package.
+In this table, you can find the successive versions of this HAL-LL Driver component, in line with the corresponding versions of the full MCU package:
It is **crucial** that you use a consistent set of versions for the CMSIS Core - CMSIS Device - HAL, as mentioned in this table.
HAL Driver WL | CMSIS Device WL | CMSIS Core | Was delivered in the full MCU package
------------- | --------------- | ---------- | -------------------------------------
-Tag v1.0.0 | Tag v1.0.0 | Tag V5.6.0_cm4 | Tag v1.0.0 (and following, if any, till next HAL tag)
+Tag v1.0.0 | Tag v1.0.0 | Tag V5.6.0_cm4 | Tag v1.0.0 (and following, if any, till next tag)
+Tag v1.1.0 | Tag v1.1.0 | Tag V5.6.0_cm4 | Tag v1.1.0 (and following, if any, till next tag)
+
The full **STM32CubeWL** MCU package is available [here](https://github.com/STMicroelectronics/STM32CubeWL).
## Troubleshooting
-If you have any issue with the **software content** of this repository, you can file an issue [here](https://github.com/STMicroelectronics/stm32wlxx_hal_driver/issues/new/choose).
+If you have any issue with the **Software content** of this repository, you can file an issue [here](https://github.com/STMicroelectronics/stm32wlxx_hal_driver/issues/new/choose).
-For any other question related to the product, the tools, the environment, you can submit a topic to the [ST Community](https://community.st.com/s/).
+For any other question related to the product, the tools, the environment, you can submit a topic on the [ST Community/STM32 MCUs forum](https://community.st.com/s/group/0F90X000000AXsASAW/stm32-mcus).
diff --git a/Release_Notes.html b/Release_Notes.html
index 1ad577f..1c47340 100644
--- a/Release_Notes.html
+++ b/Release_Notes.html
@@ -21,7 +21,8 @@
<div class="row">
<div class="col-sm-12 col-lg-4">
<center>
-<h1 id="release-notes-forstm32wlxx-hal-drivers"><small>Release Notes for</small><mark>STM32WLxx HAL Drivers</mark></h1>
+<h1 id="release-notes-for">Release Notes for</h1>
+<h1 id="stm32wlxx-hal-drivers"><mark>STM32WLxx HAL Drivers</mark></h1>
<p>Copyright © 2020 STMicroelectronics</p>
<a href="https://www.st.com" class="logo"><img src="_htmresc/st_logo_2020.png" alt="ST logo" /></a>
</center>
@@ -42,19 +43,184 @@
<div class="col-sm-12 col-lg-8">
<h1 id="update-history">Update History</h1>
<div class="collapse">
-<input type="checkbox" id="collapse-section1" checked aria-hidden="true"> <label for="collapse-section1" aria-hidden="true"><strong>V1.0.0 / 28-October-2020</strong></label>
+<input type="checkbox" id="collapse-section2" checked aria-hidden="true"> <label for="collapse-section2" aria-hidden="true"><strong>V1.1.0 / 16-June-2021</strong></label>
<div>
<h2 id="main-changes">Main Changes</h2>
-<p><strong>First Official Release</strong></p>
+<ul>
+<li>Maintenance release of <strong>HAL and Low Layer</strong> drivers to include latest corrections</li>
+<li>Update of HAL SMBUS driver to introduce fast mode and fast mode plus
+<ul>
+<li>Add extension files stm32wlxx_hal_smbus_ex.h/.c for new APIs:
+<ul>
+<li><em>HAL_SMBUSEx_EnableFastModePlus()</em></li>
+<li><em>HAL_SMBUSEx_DisableFastModePlus()</em></li>
+</ul></li>
+</ul></li>
+</ul>
<h2 id="contents">Contents</h2>
-<p>First official release of LL / HAL Drivers for STM32WLxx series.</p>
+<h3 id="hal-drivers-updates"><strong>HAL Drivers</strong> updates</h3>
+<ul>
+<li><strong>HAL ADC</strong> driver
+<ul>
+<li>Update CFGR2 oversampling bitfields conditionally to oversampling enable</li>
+<li>Update timeout mechanism to avoid false timeout detection in case of preemption</li>
+<li>Update wait_loop_index computation so delay in us is always multiplicated by at least value “1”</li>
+</ul></li>
+<li><strong>HAL COMP</strong> driver
+<ul>
+<li>Update wait_loop_index computation so delay in us is always multiplicated by at least value “1”</li>
+</ul></li>
+<li><strong>HAL CORTEX</strong> driver
+<ul>
+<li>Disable the smallest MPU region sizes (32B, 64B, 128B) in the M0+ context</li>
+</ul></li>
+<li><strong>HAL CRYP</strong> driver
+<ul>
+<li>Update HAL_CRYP_SetConfig() and HAL_CRYP_GetConfig() APIs to set/get the continent of KeyIVConfigSkip correctly</li>
+<li>Resolve interrupt mode related GCM decryption issue causing wrong computation of decryption size</li>
+<li>Update HAL_CRYP_InCpltCallback() API to fix an incorrect condition call at resumption time</li>
+<li>Update CRYP_AESCCM_Process_IT() to fix incorrect CCM header length management when data are fed to the peripheral under interrupt</li>
+</ul></li>
+<li><strong>HAL EXTI</strong> driver
+<ul>
+<li>Update HAL_EXTI_GetConfigLine() to set default configuration value of Trigger and GPIOSel before checking each corresponding register</li>
+</ul></li>
+<li><strong>HAL GPIO</strong> driver
+<ul>
+<li>Update HAL_GPIO_Init() API to avoid the configuration of PUPDR register when Analog mode is selected</li>
+</ul></li>
+<li><strong>HAL HSEM</strong> driver
+<ul>
+<li>Update SemID comment related to the number of semaphores</li>
+</ul></li>
+<li><strong>HAL I2C</strong> driver
+<ul>
+<li>Updated I2C_IsAcknowledgeFailed() to avoid keeping I2C in busy state if NACK is received after transmitting register address</li>
+</ul></li>
+<li><strong>HAL IRDA</strong> driver
+<ul>
+<li>Fixed typos in the IRDA State definition description</li>
+</ul></li>
+<li><strong>HAL IWDG</strong> driver
+<ul>
+<li>Updated HAL_IWDG_Init() API in order to fix HAL_GetTick() timeout vulnerability issue</li>
+</ul></li>
+<li><strong>HAL LPTIM</strong> driver
+<ul>
+<li>Update HAL_LPTIM_Init() API implementation to configure digital filter for external clock when LPTIM is clocked by an internal clock source</li>
+</ul></li>
+<li><strong>HAL PWR</strong> driver
+<ul>
+<li>Correct HAL_PWREx_DisableInternalWakeUpLine() to update CM0+ register</li>
+</ul></li>
+<li><strong>HAL RCC</strong> driver
+<ul>
+<li>Update definition of IS_RCC_OSCILLATORTYPE() macro</li>
+<li>Update IS_RCC_PERIPHCLOCK() macro definition depending on targeted derivative</li>
+<li>Add new API HAL_RCC_GetResetSource() to get all reset sources and clear flags for next reset</li>
+</ul></li>
+<li><strong>HAL RNG</strong> driver
+<ul>
+<li>Update timeout mechanism to avoid false timeout detection in case of preemption</li>
+</ul></li>
+<li><strong>HAL RTC</strong> driver
+<ul>
+<li>Update HAL_RTC_DeactivateAlarm() to fix issue where Alarm Autoclear remained activated after deactivating alarm</li>
+<li>Update HAL_RTCEx_SetTimeStamp_IT() to avoid the call of TimeStamp callback during the setting of the TimeStamp</li>
+<li>Update assertions in HAL_RTC_SetAlarm() and HAL_RTC_SetAlarm_IT() to allow user to unset some Alarm parameters when AlarmMask is set</li>
+<li>Update HAL_RTC_DeactivateAlarm() to clear Alarm Flag</li>
+<li>Update HAL_RTCEx_DeactivateTimeStamp() to clear TimeStamp flag</li>
+<li>Update HAL_RTCEx_DeactivateInternalTimeStamp() to clear Internal TimeStamp flag
+<ul>
+<li>The flag is cleared only if TSOVF & TSE are set to 0</li>
+</ul></li>
+<li>Update HAL_RTCEx_DeactivateWakeUpTimer() to clear WakeUpTimer flag</li>
+<li>Update HAL_RTCEx_DeactivateSSRU() to clear SSR Underflow flag</li>
+<li>Update HAL_RTC_WaitForSynchro() to fix issue to clear RSF flag</li>
+</ul></li>
+<li><strong>HAL SMARTCARD</strong> driver
+<ul>
+<li>Fixed typos in the SMARTCARD State definition description</li>
+</ul></li>
+<li><strong>HAL SMBUS</strong> driver
+<ul>
+<li>Add support for Fast Mode Plus to be SMBUS Rev3 compliant:
+<ul>
+<li>Add HAL_SMBUSEx_EnableFastModePlus() and HAL_SMBUSEx_DisableFastModePlus() APIs to manage Fm+</li>
+</ul></li>
+</ul></li>
+<li><strong>HAL SPI</strong> driver
+<ul>
+<li>Update in SPI_WaitFifoStateUntilTimeout() to fix code optimization issue</li>
+<li>Update to fix MISRA-C 2012 Rule-13.2 issue</li>
+</ul></li>
+<li><strong>HAL SUBGHZ</strong> driver
+<ul>
+<li>Update HAL_Delay() by a polling loop to avoid blocking situation in case of Systick is mapped on Tick</li>
+<li>Update HAL_SUBGHZ_DeInit() to check RF Busy bit and deassert the reset signal on RF side</li>
+</ul></li>
+<li><strong>HAL TIM</strong> driver
+<ul>
+<li>Update HAL_TIMEx_OnePulseN_Start and HAL_TIMEx_OnePulseN_Stop (pooling and IT mode) to take into consideration all OutputChannel parameters</li>
+<li>Correct CodeSpell typos in HAL TIM drivers</li>
+<li>Update timeout mechanism to avoid false timeout detection in case of preemption</li>
+<li>Update input capture measurement in DMA mode to avoid zero return values at high frequencies</li>
+</ul></li>
+<li><strong>HAL UART</strong> driver
+<ul>
+<li>Remove an invalid FIFO mode configuration from UART_SetConfig() as it is not is not member of UART_InitTypeDef Structure</li>
+<li>Update HAL_UART_IRQHandler() API to handle receiver timeout interrupt
+<ul>
+<li>Update UART receive processes (IT and DMA) to handle the UART receive’s timeout interrupt</li>
+</ul></li>
+<li>Update arrays definition to be declared as static const</li>
+<li>Fix erroneous UART’s handle state in case of error returned after DMA reception start within UART_Start_Receive_DMA()</li>
+<li>Update UART ReceptionType management in case of ReceptionToIdle API are called from RxEvent callback</li>
+<li>Handling of UART concurrent register access in case of race condition between Tx and Rx transfers (HAL UART and LL LPUART)</li>
+</ul></li>
+</ul>
+<p><br />
+</p>
+<h3 id="ll-drivers-updates"><strong>LL Drivers</strong> updates</h3>
+<ul>
+<li><strong>LL RCC</strong> driver
+<ul>
+<li>Private functions made static</li>
+</ul></li>
+<li><strong>LL RTC</strong> driver
+<ul>
+<li>Fix wrong reference of RTC instance in LL_RTC_TIME_Init() and LL_RTC_DATE_Init() functions</li>
+</ul></li>
+<li><strong>LL SPI</strong> driver
+<ul>
+<li>Updated to set the FRXTH bit for 8bit data in LL_SPI_Init() API</li>
+<li>Update LL_SPI_TransmitData8() to avoid casting the result to 8 bits</li>
+</ul></li>
+<li><strong>LL TIM</strong> driver
+<ul>
+<li>Updated LL_TIM_GetCounterMode() API to return the correct counter mode</li>
+<li>Update reversed description of TIM_LL_EC_ONEPULSEMODE One Pulse Mode</li>
+</ul></li>
+<li><strong>LL LPUART</strong> driver
+<ul>
+<li>Handling of UART concurrent register access in case of race condition between Tx and Rx transfers (HAL UART and LL LPUART)</li>
+</ul></li>
+<li><strong>LL USART</strong> driver
+<ul>
+<li>Handling of UART concurrent register access in case of race condition between Tx and Rx transfers (HAL UART and LL LPUART)</li>
+<li>LL_USART_ClockInit now supports clock phase and clock polarity configuration for SPI_Slave mode</li>
+<li>Remove useless check on maximum BRR value by removing IS_LL_USART_BRR_MAX() macro</li>
+</ul></li>
+</ul>
+<p><br />
+</p>
<h2 id="known-limitations">Known Limitations</h2>
<p>None</p>
<h2 id="development-toolchains-and-compilers">Development Toolchains and Compilers</h2>
<ul>
<li>IAR Embedded Workbench for ARM (EWARM) toolchain V8.30.1</li>
-<li>RealView Microcontroller Development Kit (MDK-ARM) toolchain V5.28</li>
-<li>STM32CubeIDE 1.5.0</li>
+<li>RealView Microcontroller Development Kit (MDK-ARM) toolchain V5.31</li>
+<li>STM32CubeIDE 1.7.0</li>
</ul>
<h2 id="supported-devices-and-boards">Supported Devices and boards</h2>
<p>Supported Devices:</p>
@@ -72,6 +238,37 @@
</p>
</div>
</div>
+<div class="collapse">
+<input type="checkbox" id="collapse-section1" aria-hidden="true"> <label for="collapse-section1" aria-hidden="true"><strong>V1.0.0 / 28-October-2020</strong></label>
+<div>
+<h2 id="main-changes-1">Main Changes</h2>
+<p><strong>First Official Release</strong></p>
+<h2 id="contents-1">Contents</h2>
+<p>First official release of LL / HAL Drivers for STM32WLxx series.</p>
+<h2 id="known-limitations-1">Known Limitations</h2>
+<p>None</p>
+<h2 id="development-toolchains-and-compilers-1">Development Toolchains and Compilers</h2>
+<ul>
+<li>IAR Embedded Workbench for ARM (EWARM) toolchain V8.30.1</li>
+<li>RealView Microcontroller Development Kit (MDK-ARM) toolchain V5.28</li>
+<li>STM32CubeIDE 1.5.0</li>
+</ul>
+<h2 id="supported-devices-and-boards-1">Supported Devices and boards</h2>
+<p>Supported Devices:</p>
+<ul>
+<li>STM32WL55xx</li>
+<li>STM32WL54xx</li>
+<li>STM32WLE5xx</li>
+<li>STM32WLE4xx</li>
+</ul>
+<h2 id="backward-compatibility-1">Backward Compatibility</h2>
+<p>Not applicable</p>
+<h2 id="dependencies-1">Dependencies</h2>
+<p>None</p>
+<p><br />
+</p>
+</div>
+</div>
</div>
</div>
<footer class="sticky">
diff --git a/Src/stm32wlxx_hal.c b/Src/stm32wlxx_hal.c
index d656297..45d49c6 100644
--- a/Src/stm32wlxx_hal.c
+++ b/Src/stm32wlxx_hal.c
@@ -56,7 +56,7 @@
* @brief STM32WLxx HAL Driver version number
*/
#define __STM32WLxx_HAL_VERSION_MAIN (0x01U) /*!< [31:24] main version */
-#define __STM32WLxx_HAL_VERSION_SUB1 (0x00U) /*!< [23:16] sub1 version */
+#define __STM32WLxx_HAL_VERSION_SUB1 (0x01U) /*!< [23:16] sub1 version */
#define __STM32WLxx_HAL_VERSION_SUB2 (0x00U) /*!< [15:8] sub2 version */
#define __STM32WLxx_HAL_VERSION_RC (0x00U) /*!< [7:0] release candidate */
#define __STM32WLxx_HAL_VERSION ((__STM32WLxx_HAL_VERSION_MAIN << 24U)\
diff --git a/Src/stm32wlxx_hal_adc.c b/Src/stm32wlxx_hal_adc.c
index f56cb36..b3eb314 100644
--- a/Src/stm32wlxx_hal_adc.c
+++ b/Src/stm32wlxx_hal_adc.c
@@ -211,11 +211,11 @@
The compilation flag USE_HAL_ADC_REGISTER_CALLBACKS, when set to 1,
allows the user to configure dynamically the driver callbacks.
- Use Functions @ref HAL_ADC_RegisterCallback()
+ Use Functions HAL_ADC_RegisterCallback()
to register an interrupt callback.
[..]
- Function @ref HAL_ADC_RegisterCallback() allows to register following callbacks:
+ Function HAL_ADC_RegisterCallback() allows to register following callbacks:
(+) ConvCpltCallback : ADC conversion complete callback
(+) ConvHalfCpltCallback : ADC conversion DMA half-transfer callback
(+) LevelOutOfWindowCallback : ADC analog watchdog 1 callback
@@ -229,11 +229,11 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_ADC_UnRegisterCallback to reset a callback to the default
+ Use function HAL_ADC_UnRegisterCallback to reset a callback to the default
weak function.
[..]
- @ref HAL_ADC_UnRegisterCallback takes as parameters the HAL peripheral handle,
+ HAL_ADC_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) ConvCpltCallback : ADC conversion complete callback
@@ -247,27 +247,27 @@
(+) MspDeInitCallback : ADC Msp DeInit callback
[..]
- By default, after the @ref HAL_ADC_Init() and when the state is @ref HAL_ADC_STATE_RESET
+ By default, after the HAL_ADC_Init() and when the state is HAL_ADC_STATE_RESET
all callbacks are set to the corresponding weak functions:
- examples @ref HAL_ADC_ConvCpltCallback(), @ref HAL_ADC_ErrorCallback().
+ examples HAL_ADC_ConvCpltCallback(), HAL_ADC_ErrorCallback().
Exception done for MspInit and MspDeInit functions that are
- reset to the legacy weak functions in the @ref HAL_ADC_Init()/ @ref HAL_ADC_DeInit() only when
+ reset to the legacy weak functions in the HAL_ADC_Init()/HAL_ADC_DeInit() only when
these callbacks are null (not registered beforehand).
[..]
- If MspInit or MspDeInit are not null, the @ref HAL_ADC_Init()/ @ref HAL_ADC_DeInit()
+ If MspInit or MspDeInit are not null, the HAL_ADC_Init()/HAL_ADC_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
[..]
- Callbacks can be registered/unregistered in @ref HAL_ADC_STATE_READY state only.
+ Callbacks can be registered/unregistered in HAL_ADC_STATE_READY state only.
Exception done MspInit/MspDeInit functions that can be registered/unregistered
- in @ref HAL_ADC_STATE_READY or @ref HAL_ADC_STATE_RESET state,
+ in HAL_ADC_STATE_READY or HAL_ADC_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
[..]
Then, the user first registers the MspInit/MspDeInit user callbacks
- using @ref HAL_ADC_RegisterCallback() before calling @ref HAL_ADC_DeInit()
- or @ref HAL_ADC_Init() function.
+ using HAL_ADC_RegisterCallback() before calling HAL_ADC_DeInit()
+ or HAL_ADC_Init() function.
[..]
When the compilation flag USE_HAL_ADC_REGISTER_CALLBACKS is set to 0 or
@@ -416,7 +416,12 @@
assert_param(IS_ADC_SAMPLE_TIME(hadc->Init.SamplingTimeCommon1));
assert_param(IS_ADC_SAMPLE_TIME(hadc->Init.SamplingTimeCommon2));
assert_param(IS_FUNCTIONAL_STATE(hadc->Init.OversamplingMode));
-
+ if (hadc->Init.OversamplingMode == ENABLE)
+ {
+ assert_param(IS_ADC_OVERSAMPLING_RATIO(hadc->Init.Oversampling.Ratio));
+ assert_param(IS_ADC_RIGHT_BIT_SHIFT(hadc->Init.Oversampling.RightBitShift));
+ assert_param(IS_ADC_TRIGGERED_OVERSAMPLING_MODE(hadc->Init.Oversampling.TriggeredMode));
+ }
assert_param(IS_ADC_TRIGGER_FREQ(hadc->Init.TriggerFrequencyMode));
if (hadc->Init.ScanConvMode != ADC_SCAN_DISABLE)
@@ -476,7 +481,7 @@
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles, scaling in us split to not */
/* exceed 32 bits register capacity and handle low frequency. */
- wait_loop_index = ((LL_ADC_DELAY_INTERNAL_REGUL_STAB_US / 10UL) * (SystemCoreClock / (100000UL * 2UL)));
+ wait_loop_index = ((LL_ADC_DELAY_INTERNAL_REGUL_STAB_US / 10UL) * ((SystemCoreClock / (100000UL * 2UL)) + 1UL));
while (wait_loop_index != 0UL)
{
wait_loop_index--;
@@ -531,7 +536,7 @@
/* function on the fly (update of a parameter of ADC_InitTypeDef */
/* without needing to reconfigure all other ADC groups/channels */
/* parameters): */
- /* - internal measurement paths: Vbat, temperature sensor, Vref */
+ /* - internal measurement paths (VrefInt, ...) */
/* (set into HAL_ADC_ConfigChannel() ) */
/* Configuration of ADC resolution */
@@ -540,15 +545,17 @@
hadc->Init.Resolution);
tmpCFGR2 |= ((hadc->Init.ClockPrescaler & ADC_CFGR2_CKMODE) |
- hadc->Init.Oversampling.Ratio |
- hadc->Init.Oversampling.RightBitShift |
- hadc->Init.Oversampling.TriggeredMode |
hadc->Init.TriggerFrequencyMode
);
if (hadc->Init.OversamplingMode == ENABLE)
{
- SET_BIT(tmpCFGR2, ADC_CFGR2_OVSE);
+ tmpCFGR2 |= (ADC_CFGR2_OVSE |
+ (hadc->Init.ClockPrescaler & ADC_CFGR2_CKMODE) |
+ hadc->Init.Oversampling.Ratio |
+ hadc->Init.Oversampling.RightBitShift |
+ hadc->Init.Oversampling.TriggeredMode
+ );
}
MODIFY_REG(hadc->Instance->CFGR2,
@@ -748,7 +755,6 @@
tmp_hal_status = HAL_ERROR;
}
- /* Return function status */
return tmp_hal_status;
}
@@ -764,9 +770,6 @@
* bypassed without error reporting: it can be the intended behavior in
* case of reset of a single ADC while the other ADCs sharing the same
* common group is still running.
- * @note By default, HAL_ADC_DeInit() set ADC in mode deep power-down:
- * this saves more power by reducing leakage currents
- * and is particularly interesting before entering MCU low-power modes.
* @param hadc ADC handle
* @retval HAL status
*/
@@ -858,12 +861,10 @@
/* ========== Hard reset ADC peripheral ========== */
/* Performs a global reset of the entire ADC peripheral: ADC state is */
/* forced to a similar state after device power-on. */
- /* If needed, copy-paste and uncomment the following reset code into */
- /* function "void HAL_ADC_MspDeInit(ADC_HandleTypeDef *hadc)": */
- /* */
- /* __HAL_RCC_ADC_FORCE_RESET() */
- /* __HAL_RCC_ADC_RELEASE_RESET() */
-
+ /* Note: A possible implementation is to add RCC bus reset of ADC */
+ /* (for example, using macro */
+ /* __HAL_RCC_ADC..._FORCE_RESET()/..._RELEASE_RESET()/..._CLK_DISABLE()) */
+ /* in function "void HAL_ADC_MspDeInit(ADC_HandleTypeDef *hadc)": */
#if (USE_HAL_ADC_REGISTER_CALLBACKS == 1)
if (hadc->MspDeInitCallback == NULL)
{
@@ -886,10 +887,8 @@
/* Set ADC state */
hadc->State = HAL_ADC_STATE_RESET;
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -1192,7 +1191,6 @@
/* Perform ADC enable and conversion start if no conversion is on going */
if (LL_ADC_REG_IsConversionOngoing(hadc->Instance) == 0UL)
{
- /* Process locked */
__HAL_LOCK(hadc);
/* Enable the ADC peripheral */
@@ -1230,7 +1228,6 @@
}
else
{
- /* Process unlocked */
__HAL_UNLOCK(hadc);
}
}
@@ -1239,7 +1236,6 @@
tmp_hal_status = HAL_BUSY;
}
- /* Return function status */
return tmp_hal_status;
}
@@ -1259,7 +1255,6 @@
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
- /* Process locked */
__HAL_LOCK(hadc);
/* 1. Stop potential conversion on going, on ADC group regular */
@@ -1281,10 +1276,8 @@
}
}
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -1309,7 +1302,7 @@
HAL_StatusTypeDef HAL_ADC_PollForConversion(ADC_HandleTypeDef *hadc, uint32_t Timeout)
{
uint32_t tickstart;
- uint32_t tmp_Flag_End;
+ uint32_t tmp_flag_end;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
@@ -1317,7 +1310,7 @@
/* If end of conversion selected to end of sequence conversions */
if (hadc->Init.EOCSelection == ADC_EOC_SEQ_CONV)
{
- tmp_Flag_End = ADC_FLAG_EOS;
+ tmp_flag_end = ADC_FLAG_EOS;
}
/* If end of conversion selected to end of unitary conversion */
else /* ADC_EOC_SINGLE_CONV */
@@ -1337,7 +1330,7 @@
}
else
{
- tmp_Flag_End = (ADC_FLAG_EOC);
+ tmp_flag_end = (ADC_FLAG_EOC);
}
}
@@ -1345,20 +1338,23 @@
tickstart = HAL_GetTick();
/* Wait until End of unitary conversion or sequence conversions flag is raised */
- while ((hadc->Instance->ISR & tmp_Flag_End) == 0UL)
+ while ((hadc->Instance->ISR & tmp_flag_end) == 0UL)
{
/* Check if timeout is disabled (set to infinite wait) */
if (Timeout != HAL_MAX_DELAY)
{
if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0UL))
{
- /* Update ADC state machine to timeout */
- SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
+ /* New check to avoid false timeout detection in case of preemption */
+ if ((hadc->Instance->ISR & tmp_flag_end) == 0UL)
+ {
+ /* Update ADC state machine to timeout */
+ SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
- /* Process unlocked */
- __HAL_UNLOCK(hadc);
+ __HAL_UNLOCK(hadc);
- return HAL_TIMEOUT;
+ return HAL_TIMEOUT;
+ }
}
}
}
@@ -1452,13 +1448,16 @@
{
if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0UL))
{
- /* Update ADC state machine to timeout */
- SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
+ /* New check to avoid false timeout detection in case of preemption */
+ if (__HAL_ADC_GET_FLAG(hadc, EventType) == 0UL)
+ {
+ /* Update ADC state machine to timeout */
+ SET_BIT(hadc->State, HAL_ADC_STATE_TIMEOUT);
- /* Process unlocked */
- __HAL_UNLOCK(hadc);
+ __HAL_UNLOCK(hadc);
- return HAL_TIMEOUT;
+ return HAL_TIMEOUT;
+ }
}
}
}
@@ -1570,7 +1569,6 @@
/* Perform ADC enable and conversion start if no conversion is on going */
if (LL_ADC_REG_IsConversionOngoing(hadc->Instance) == 0UL)
{
- /* Process locked */
__HAL_LOCK(hadc);
/* Enable the ADC peripheral */
@@ -1633,7 +1631,6 @@
}
else
{
- /* Process unlocked */
__HAL_UNLOCK(hadc);
}
@@ -1643,7 +1640,6 @@
tmp_hal_status = HAL_BUSY;
}
- /* Return function status */
return tmp_hal_status;
}
@@ -1661,7 +1657,6 @@
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
- /* Process locked */
__HAL_LOCK(hadc);
/* 1. Stop potential conversion on going, on ADC group regular */
@@ -1687,10 +1682,8 @@
}
}
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -1714,7 +1707,6 @@
/* Perform ADC enable and conversion start if no conversion is on going */
if (LL_ADC_REG_IsConversionOngoing(hadc->Instance) == 0UL)
{
- /* Process locked */
__HAL_LOCK(hadc);
/* Specific case for first call occurrence of this function (DMA transfer */
@@ -1791,7 +1783,6 @@
tmp_hal_status = HAL_BUSY;
}
- /* Return function status */
return tmp_hal_status;
}
@@ -1809,7 +1800,6 @@
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
- /* Process locked */
__HAL_LOCK(hadc);
/* 1. Stop potential ADC group regular conversion on going */
@@ -1860,10 +1850,8 @@
CLEAR_BIT(hadc->Instance->CFGR1, ADC_CFGR1_DMAEN);
}
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -2100,7 +2088,7 @@
/* ========== Check channel configuration ready flag ========== */
if (((tmp_isr & ADC_FLAG_CCRDY) == ADC_FLAG_CCRDY) && ((tmp_ier & ADC_IT_CCRDY) == ADC_IT_CCRDY))
{
- /* Level out of window 1 callback */
+ /* Channel configuration ready callback */
HAL_ADCEx_ChannelConfigReadyCallback(hadc);
/* Clear ADC analog watchdog flag */
@@ -2208,10 +2196,10 @@
* The setting of these parameters is conditioned to ADC state:
* Refer to comments of structure "ADC_ChannelConfTypeDef".
* @param hadc ADC handle
- * @param sConfig Structure of ADC channel assigned to ADC group regular.
+ * @param pConfig Structure of ADC channel assigned to ADC group regular.
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef *hadc, ADC_ChannelConfTypeDef *sConfig)
+HAL_StatusTypeDef HAL_ADC_ConfigChannel(ADC_HandleTypeDef *hadc, ADC_ChannelConfTypeDef *pConfig)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
uint32_t tmp_config_internal_channel;
@@ -2219,22 +2207,21 @@
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
- assert_param(IS_ADC_CHANNEL(sConfig->Channel));
- assert_param(IS_ADC_SAMPLING_TIME_COMMON(sConfig->SamplingTime));
+ assert_param(IS_ADC_CHANNEL(pConfig->Channel));
+ assert_param(IS_ADC_SAMPLING_TIME_COMMON(pConfig->SamplingTime));
if ((hadc->Init.ScanConvMode == ADC_SCAN_SEQ_FIXED) ||
(hadc->Init.ScanConvMode == ADC_SCAN_SEQ_FIXED_BACKWARD))
{
- assert_param(IS_ADC_REGULAR_RANK_SEQ_FIXED(sConfig->Rank));
+ assert_param(IS_ADC_REGULAR_RANK_SEQ_FIXED(pConfig->Rank));
}
else
{
assert_param(IS_ADC_REGULAR_NB_CONV(hadc->Init.NbrOfConversion));
- assert_param(IS_ADC_REGULAR_RANK(sConfig->Rank));
+ assert_param(IS_ADC_REGULAR_RANK(pConfig->Rank));
}
- /* Process locked */
__HAL_LOCK(hadc);
/* Parameters update conditioned to ADC state: */
@@ -2252,7 +2239,7 @@
/* Otherwise (sequencer set to fully configurable or to to not fully */
/* configurable with channel rank to be set), configure the selected */
/* channel. */
- if (sConfig->Rank != ADC_RANK_NONE)
+ if (pConfig->Rank != ADC_RANK_NONE)
{
/* Regular sequence configuration */
/* Note: ADC channel configuration requires few ADC clock cycles */
@@ -2265,7 +2252,7 @@
{
/* Sequencer set to not fully configurable: */
/* Set the channel by enabling the corresponding bitfield. */
- LL_ADC_REG_SetSequencerChAdd(hadc->Instance, sConfig->Channel);
+ LL_ADC_REG_SetSequencerChAdd(hadc->Instance, pConfig->Channel);
}
else
{
@@ -2274,21 +2261,21 @@
/* Memorize the channel set into variable in HAL ADC handle */
MODIFY_REG(hadc->ADCGroupRegularSequencerRanks,
- ADC_CHSELR_SQ1 << (sConfig->Rank & 0x1FUL),
- __LL_ADC_CHANNEL_TO_DECIMAL_NB(sConfig->Channel) << (sConfig->Rank & 0x1FUL));
+ ADC_CHSELR_SQ1 << (pConfig->Rank & 0x1FUL),
+ __LL_ADC_CHANNEL_TO_DECIMAL_NB(pConfig->Channel) << (pConfig->Rank & 0x1FUL));
/* If the selected rank is below ADC group regular sequencer length, */
/* apply the configuration in ADC register. */
/* Note: Otherwise, configuration is not applied. */
/* To apply it, parameter'NbrOfConversion' must be increased. */
- if (((sConfig->Rank >> 2UL) + 1UL) <= hadc->Init.NbrOfConversion)
+ if (((pConfig->Rank >> 2UL) + 1UL) <= hadc->Init.NbrOfConversion)
{
- LL_ADC_REG_SetSequencerRanks(hadc->Instance, sConfig->Rank, sConfig->Channel);
+ LL_ADC_REG_SetSequencerRanks(hadc->Instance, pConfig->Rank, pConfig->Channel);
}
}
/* Set sampling time of the selected ADC channel */
- LL_ADC_SetChannelSamplingTime(hadc->Instance, sConfig->Channel, sConfig->SamplingTime);
+ LL_ADC_SetChannelSamplingTime(hadc->Instance, pConfig->Channel, pConfig->SamplingTime);
/* Management of internal measurement channels: VrefInt/TempSensor/Vbat */
/* internal measurement paths enable: If internal channel selected, */
@@ -2296,13 +2283,13 @@
/* Note: these internal measurement paths can be disabled using */
/* HAL_ADC_DeInit() or removing the channel from sequencer with */
/* channel configuration parameter "Rank". */
- if (__LL_ADC_IS_CHANNEL_INTERNAL(sConfig->Channel))
+ if (__LL_ADC_IS_CHANNEL_INTERNAL(pConfig->Channel))
{
tmp_config_internal_channel = LL_ADC_GetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance));
/* If the requested internal measurement path has already been enabled, */
/* bypass the configuration processing. */
- if ((sConfig->Channel == ADC_CHANNEL_TEMPSENSOR) &&
+ if ((pConfig->Channel == ADC_CHANNEL_TEMPSENSOR) &&
((tmp_config_internal_channel & LL_ADC_PATH_INTERNAL_TEMPSENSOR) == 0UL))
{
LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance),
@@ -2313,18 +2300,18 @@
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles, scaling in us split to not */
/* exceed 32 bits register capacity and handle low frequency. */
- wait_loop_index = (((LL_ADC_DELAY_TEMPSENSOR_STAB_US / 10UL) * (SystemCoreClock / (100000UL * 2UL))) + 1UL);
+ wait_loop_index = ((LL_ADC_DELAY_TEMPSENSOR_STAB_US / 10UL) * ((SystemCoreClock / (100000UL * 2UL)) + 1UL));
while (wait_loop_index != 0UL)
{
wait_loop_index--;
}
}
- else if ((sConfig->Channel == ADC_CHANNEL_VBAT) && ((tmp_config_internal_channel & LL_ADC_PATH_INTERNAL_VBAT) == 0UL))
+ else if ((pConfig->Channel == ADC_CHANNEL_VBAT) && ((tmp_config_internal_channel & LL_ADC_PATH_INTERNAL_VBAT) == 0UL))
{
LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance),
LL_ADC_PATH_INTERNAL_VBAT | tmp_config_internal_channel);
}
- else if ((sConfig->Channel == ADC_CHANNEL_VREFINT) &&
+ else if ((pConfig->Channel == ADC_CHANNEL_VREFINT) &&
((tmp_config_internal_channel & LL_ADC_PATH_INTERNAL_VREFINT) == 0UL))
{
LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance),
@@ -2348,27 +2335,27 @@
{
/* Sequencer set to not fully configurable: */
/* Reset the channel by disabling the corresponding bitfield. */
- LL_ADC_REG_SetSequencerChRem(hadc->Instance, sConfig->Channel);
+ LL_ADC_REG_SetSequencerChRem(hadc->Instance, pConfig->Channel);
}
/* Management of internal measurement channels: Vbat/VrefInt/TempSensor. */
/* If internal channel selected, enable dedicated internal buffers and */
/* paths. */
- if (__LL_ADC_IS_CHANNEL_INTERNAL(sConfig->Channel))
+ if (__LL_ADC_IS_CHANNEL_INTERNAL(pConfig->Channel))
{
tmp_config_internal_channel = LL_ADC_GetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance));
- if (sConfig->Channel == ADC_CHANNEL_TEMPSENSOR)
+ if (pConfig->Channel == ADC_CHANNEL_TEMPSENSOR)
{
LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance),
~LL_ADC_PATH_INTERNAL_TEMPSENSOR & tmp_config_internal_channel);
}
- else if (sConfig->Channel == ADC_CHANNEL_VBAT)
+ else if (pConfig->Channel == ADC_CHANNEL_VBAT)
{
LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance),
~LL_ADC_PATH_INTERNAL_VBAT & tmp_config_internal_channel);
}
- else if (sConfig->Channel == ADC_CHANNEL_VREFINT)
+ else if (pConfig->Channel == ADC_CHANNEL_VREFINT)
{
LL_ADC_SetCommonPathInternalCh(__LL_ADC_COMMON_INSTANCE(hadc->Instance),
~LL_ADC_PATH_INTERNAL_VREFINT & tmp_config_internal_channel);
@@ -2392,10 +2379,8 @@
tmp_hal_status = HAL_ERROR;
}
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -2418,24 +2403,24 @@
* bus activity, this might cause an uncertainty on the
* effective timing of the new programmed threshold values.
* @param hadc ADC handle
- * @param AnalogWDGConfig Structure of ADC analog watchdog configuration
+ * @param pAnalogWDGConfig Structure of ADC analog watchdog configuration
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef *hadc, ADC_AnalogWDGConfTypeDef *AnalogWDGConfig)
+HAL_StatusTypeDef HAL_ADC_AnalogWDGConfig(ADC_HandleTypeDef *hadc, ADC_AnalogWDGConfTypeDef *pAnalogWDGConfig)
{
HAL_StatusTypeDef tmp_hal_status = HAL_OK;
- uint32_t tmpAWDHighThresholdShifted;
- uint32_t tmpAWDLowThresholdShifted;
+ uint32_t tmp_awd_high_threshold_shifted;
+ uint32_t tmp_awd_low_threshold_shifted;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
- assert_param(IS_ADC_ANALOG_WATCHDOG_NUMBER(AnalogWDGConfig->WatchdogNumber));
- assert_param(IS_ADC_ANALOG_WATCHDOG_MODE(AnalogWDGConfig->WatchdogMode));
- assert_param(IS_FUNCTIONAL_STATE(AnalogWDGConfig->ITMode));
+ assert_param(IS_ADC_ANALOG_WATCHDOG_NUMBER(pAnalogWDGConfig->WatchdogNumber));
+ assert_param(IS_ADC_ANALOG_WATCHDOG_MODE(pAnalogWDGConfig->WatchdogMode));
+ assert_param(IS_FUNCTIONAL_STATE(pAnalogWDGConfig->ITMode));
- if (AnalogWDGConfig->WatchdogMode == ADC_ANALOGWATCHDOG_SINGLE_REG)
+ if (pAnalogWDGConfig->WatchdogMode == ADC_ANALOGWATCHDOG_SINGLE_REG)
{
- assert_param(IS_ADC_CHANNEL(AnalogWDGConfig->Channel));
+ assert_param(IS_ADC_CHANNEL(pAnalogWDGConfig->Channel));
}
/* Verify thresholds range */
@@ -2444,17 +2429,16 @@
/* Case of oversampling enabled: depending on ratio and shift configuration,
analog watchdog thresholds can be higher than ADC resolution.
Verify if thresholds are within maximum thresholds range. */
- assert_param(IS_ADC_RANGE(ADC_RESOLUTION_12B, AnalogWDGConfig->HighThreshold));
- assert_param(IS_ADC_RANGE(ADC_RESOLUTION_12B, AnalogWDGConfig->LowThreshold));
+ assert_param(IS_ADC_RANGE(ADC_RESOLUTION_12B, pAnalogWDGConfig->HighThreshold));
+ assert_param(IS_ADC_RANGE(ADC_RESOLUTION_12B, pAnalogWDGConfig->LowThreshold));
}
else
{
/* Verify if thresholds are within the selected ADC resolution */
- assert_param(IS_ADC_RANGE(ADC_GET_RESOLUTION(hadc), AnalogWDGConfig->HighThreshold));
- assert_param(IS_ADC_RANGE(ADC_GET_RESOLUTION(hadc), AnalogWDGConfig->LowThreshold));
+ assert_param(IS_ADC_RANGE(ADC_GET_RESOLUTION(hadc), pAnalogWDGConfig->HighThreshold));
+ assert_param(IS_ADC_RANGE(ADC_GET_RESOLUTION(hadc), pAnalogWDGConfig->LowThreshold));
}
- /* Process locked */
__HAL_LOCK(hadc);
/* Parameters update conditioned to ADC state: */
@@ -2464,16 +2448,16 @@
if (LL_ADC_REG_IsConversionOngoing(hadc->Instance) == 0UL)
{
/* Analog watchdog configuration */
- if (AnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_1)
+ if (pAnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_1)
{
/* Configuration of analog watchdog: */
/* - Set the analog watchdog enable mode: one or overall group of */
/* channels. */
- switch (AnalogWDGConfig->WatchdogMode)
+ switch (pAnalogWDGConfig->WatchdogMode)
{
case ADC_ANALOGWATCHDOG_SINGLE_REG:
LL_ADC_SetAnalogWDMonitChannels(hadc->Instance, LL_ADC_AWD1,
- __LL_ADC_ANALOGWD_CHANNEL_GROUP(AnalogWDGConfig->Channel, LL_ADC_GROUP_REGULAR));
+ __LL_ADC_ANALOGWD_CHANNEL_GROUP(pAnalogWDGConfig->Channel, LL_ADC_GROUP_REGULAR));
break;
case ADC_ANALOGWATCHDOG_ALL_REG:
@@ -2495,7 +2479,7 @@
LL_ADC_ClearFlag_AWD1(hadc->Instance);
/* Configure ADC analog watchdog interrupt */
- if (AnalogWDGConfig->ITMode == ENABLE)
+ if (pAnalogWDGConfig->ITMode == ENABLE)
{
LL_ADC_EnableIT_AWD1(hadc->Instance);
}
@@ -2507,31 +2491,31 @@
/* Case of ADC_ANALOGWATCHDOG_2 or ADC_ANALOGWATCHDOG_3 */
else
{
- switch (AnalogWDGConfig->WatchdogMode)
+ switch (pAnalogWDGConfig->WatchdogMode)
{
case ADC_ANALOGWATCHDOG_SINGLE_REG:
/* Update AWD by bitfield to keep the possibility to monitor */
/* several channels by successive calls of this function. */
- if (AnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_2)
+ if (pAnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_2)
{
- SET_BIT(hadc->Instance->AWD2CR, (1UL << __LL_ADC_CHANNEL_TO_DECIMAL_NB(AnalogWDGConfig->Channel)));
+ SET_BIT(hadc->Instance->AWD2CR, (1UL << __LL_ADC_CHANNEL_TO_DECIMAL_NB(pAnalogWDGConfig->Channel)));
}
else
{
- SET_BIT(hadc->Instance->AWD3CR, (1UL << __LL_ADC_CHANNEL_TO_DECIMAL_NB(AnalogWDGConfig->Channel)));
+ SET_BIT(hadc->Instance->AWD3CR, (1UL << __LL_ADC_CHANNEL_TO_DECIMAL_NB(pAnalogWDGConfig->Channel)));
}
break;
case ADC_ANALOGWATCHDOG_ALL_REG:
- LL_ADC_SetAnalogWDMonitChannels(hadc->Instance, AnalogWDGConfig->WatchdogNumber, LL_ADC_AWD_ALL_CHANNELS_REG);
+ LL_ADC_SetAnalogWDMonitChannels(hadc->Instance, pAnalogWDGConfig->WatchdogNumber, LL_ADC_AWD_ALL_CHANNELS_REG);
break;
default: /* ADC_ANALOGWATCHDOG_NONE */
- LL_ADC_SetAnalogWDMonitChannels(hadc->Instance, AnalogWDGConfig->WatchdogNumber, LL_ADC_AWD_DISABLE);
+ LL_ADC_SetAnalogWDMonitChannels(hadc->Instance, pAnalogWDGConfig->WatchdogNumber, LL_ADC_AWD_DISABLE);
break;
}
- if (AnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_2)
+ if (pAnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_2)
{
/* Update state, clear previous result related to AWD2 */
CLEAR_BIT(hadc->State, HAL_ADC_STATE_AWD2);
@@ -2543,7 +2527,7 @@
LL_ADC_ClearFlag_AWD2(hadc->Instance);
/* Configure ADC analog watchdog interrupt */
- if (AnalogWDGConfig->ITMode == ENABLE)
+ if (pAnalogWDGConfig->ITMode == ENABLE)
{
LL_ADC_EnableIT_AWD2(hadc->Instance);
}
@@ -2552,7 +2536,7 @@
LL_ADC_DisableIT_AWD2(hadc->Instance);
}
}
- /* (AnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_3) */
+ /* (pAnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_3) */
else
{
/* Update state, clear previous result related to AWD3 */
@@ -2565,7 +2549,7 @@
LL_ADC_ClearFlag_AWD3(hadc->Instance);
/* Configure ADC analog watchdog interrupt */
- if (AnalogWDGConfig->ITMode == ENABLE)
+ if (pAnalogWDGConfig->ITMode == ENABLE)
{
LL_ADC_EnableIT_AWD3(hadc->Instance);
}
@@ -2579,13 +2563,13 @@
}
/* Analog watchdog thresholds configuration */
- if (AnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_1)
+ if (pAnalogWDGConfig->WatchdogNumber == ADC_ANALOGWATCHDOG_1)
{
/* Shift the offset with respect to the selected ADC resolution: */
/* Thresholds have to be left-aligned on bit 11, the LSB (right bits) */
/* are set to 0. */
- tmpAWDHighThresholdShifted = ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(hadc, AnalogWDGConfig->HighThreshold);
- tmpAWDLowThresholdShifted = ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(hadc, AnalogWDGConfig->LowThreshold);
+ tmp_awd_high_threshold_shifted = ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(hadc, pAnalogWDGConfig->HighThreshold);
+ tmp_awd_low_threshold_shifted = ADC_AWD1THRESHOLD_SHIFT_RESOLUTION(hadc, pAnalogWDGConfig->LowThreshold);
}
/* Case of ADC_ANALOGWATCHDOG_2 and ADC_ANALOGWATCHDOG_3 */
else
@@ -2593,18 +2577,16 @@
/* No need to shift the offset with respect to the selected ADC resolution: */
/* Thresholds have to be left-aligned on bit 11, the LSB (right bits) */
/* are set to 0. */
- tmpAWDHighThresholdShifted = AnalogWDGConfig->HighThreshold;
- tmpAWDLowThresholdShifted = AnalogWDGConfig->LowThreshold;
+ tmp_awd_high_threshold_shifted = pAnalogWDGConfig->HighThreshold;
+ tmp_awd_low_threshold_shifted = pAnalogWDGConfig->LowThreshold;
}
/* Set ADC analog watchdog thresholds value of both thresholds high and low */
- LL_ADC_ConfigAnalogWDThresholds(hadc->Instance, AnalogWDGConfig->WatchdogNumber, tmpAWDHighThresholdShifted,
- tmpAWDLowThresholdShifted);
+ LL_ADC_ConfigAnalogWDThresholds(hadc->Instance, pAnalogWDGConfig->WatchdogNumber, tmp_awd_high_threshold_shifted,
+ tmp_awd_low_threshold_shifted);
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -2708,13 +2690,17 @@
{
if ((HAL_GetTick() - tickstart) > ADC_STOP_CONVERSION_TIMEOUT)
{
- /* Update ADC state machine to error */
- SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
+ /* New check to avoid false timeout detection in case of preemption */
+ if ((hadc->Instance->CR & ADC_CR_ADSTART) != 0UL)
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
- /* Set ADC error code to ADC peripheral internal error */
- SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+ /* Set ADC error code to ADC peripheral internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
- return HAL_ERROR;
+ return HAL_ERROR;
+ }
}
}
@@ -2764,7 +2750,7 @@
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles, scaling in us split to not */
/* exceed 32 bits register capacity and handle low frequency. */
- wait_loop_index = (((LL_ADC_DELAY_TEMPSENSOR_BUFFER_STAB_US / 10UL) * (SystemCoreClock / (100000UL * 2UL))) + 1UL);
+ wait_loop_index = ((LL_ADC_DELAY_TEMPSENSOR_BUFFER_STAB_US / 10UL) * ((SystemCoreClock / (100000UL * 2UL)) + 1UL));
while (wait_loop_index != 0UL)
{
wait_loop_index--;
@@ -2795,13 +2781,17 @@
if ((HAL_GetTick() - tickstart) > ADC_ENABLE_TIMEOUT)
{
- /* Update ADC state machine to error */
- SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
+ /* New check to avoid false timeout detection in case of preemption */
+ if (__HAL_ADC_GET_FLAG(hadc, ADC_FLAG_RDY) == 0UL)
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
- /* Set ADC error code to ADC peripheral internal error */
- SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+ /* Set ADC error code to ADC peripheral internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
- return HAL_ERROR;
+ return HAL_ERROR;
+ }
}
}
}
@@ -2856,13 +2846,17 @@
{
if ((HAL_GetTick() - tickstart) > ADC_DISABLE_TIMEOUT)
{
- /* Update ADC state machine to error */
- SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
+ /* New check to avoid false timeout detection in case of preemption */
+ if ((hadc->Instance->CR & ADC_CR_ADEN) != 0UL)
+ {
+ /* Update ADC state machine to error */
+ SET_BIT(hadc->State, HAL_ADC_STATE_ERROR_INTERNAL);
- /* Set ADC error code to ADC peripheral internal error */
- SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
+ /* Set ADC error code to ADC peripheral internal error */
+ SET_BIT(hadc->ErrorCode, HAL_ADC_ERROR_INTERNAL);
- return HAL_ERROR;
+ return HAL_ERROR;
+ }
}
}
}
diff --git a/Src/stm32wlxx_hal_adc_ex.c b/Src/stm32wlxx_hal_adc_ex.c
index 9cd5322..267367d 100644
--- a/Src/stm32wlxx_hal_adc_ex.c
+++ b/Src/stm32wlxx_hal_adc_ex.c
@@ -12,12 +12,6 @@
* Other functions (generic functions) are available in file
* "stm32wlxx_hal_adc.c".
*
- @verbatim
- [..]
- (@) Sections "ADC peripheral features" and "How to use this driver" are
- available in file of generic functions "stm32wlxx_hal_adc.c".
- [..]
- @endverbatim
******************************************************************************
* @attention
*
@@ -30,6 +24,12 @@
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
+ @verbatim
+ [..]
+ (@) Sections "ADC peripheral features" and "How to use this driver" are
+ available in file of generic functions "stm32wlxx_hal_adc.c".
+ [..]
+ @endverbatim
*/
/* Includes ------------------------------------------------------------------*/
@@ -110,7 +110,6 @@
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
- /* Process locked */
__HAL_LOCK(hadc);
/* Calibration prerequisite: ADC must be disabled. */
@@ -149,7 +148,6 @@
HAL_ADC_STATE_BUSY_INTERNAL,
HAL_ADC_STATE_ERROR_INTERNAL);
- /* Process unlocked */
__HAL_UNLOCK(hadc);
return HAL_ERROR;
@@ -172,10 +170,8 @@
/* to state "HAL_ERROR" by function disabling the ADC. */
}
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
@@ -209,7 +205,6 @@
assert_param(IS_ADC_ALL_INSTANCE(hadc->Instance));
assert_param(IS_ADC_CALFACT(CalibrationFactor));
- /* Process locked */
__HAL_LOCK(hadc);
/* Verification of hardware constraints before modifying the calibration */
@@ -234,10 +229,8 @@
tmp_hal_status = HAL_ERROR;
}
- /* Process unlocked */
__HAL_UNLOCK(hadc);
- /* Return function status */
return tmp_hal_status;
}
diff --git a/Src/stm32wlxx_hal_comp.c b/Src/stm32wlxx_hal_comp.c
index 9d5d83f..ccde724 100644
--- a/Src/stm32wlxx_hal_comp.c
+++ b/Src/stm32wlxx_hal_comp.c
@@ -335,7 +335,7 @@
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles, scaling in us split to not */
/* exceed 32 bits register capacity and handle low frequency. */
- wait_loop_index = ((COMP_DELAY_VOLTAGE_SCALER_STAB_US / 10UL) * (SystemCoreClock / (100000UL * 2UL)));
+ wait_loop_index = ((COMP_DELAY_VOLTAGE_SCALER_STAB_US / 10UL) * ((SystemCoreClock / (100000UL * 2UL)) + 1UL));
while(wait_loop_index != 0UL)
{
wait_loop_index--;
@@ -733,7 +733,7 @@
/* Note: Variable divided by 2 to compensate partially */
/* CPU processing cycles, scaling in us split to not */
/* exceed 32 bits register capacity and handle low frequency. */
- wait_loop_index = ((COMP_DELAY_STARTUP_US / 10UL) * (SystemCoreClock / (100000UL * 2UL)));
+ wait_loop_index = ((COMP_DELAY_STARTUP_US / 10UL) * ((SystemCoreClock / (100000UL * 2UL)) + 1UL));
while(wait_loop_index != 0UL)
{
wait_loop_index--;
diff --git a/Src/stm32wlxx_hal_cryp.c b/Src/stm32wlxx_hal_cryp.c
index 55dd871..3ba9898 100644
--- a/Src/stm32wlxx_hal_cryp.c
+++ b/Src/stm32wlxx_hal_cryp.c
@@ -587,15 +587,17 @@
__HAL_LOCK(hcryp);
/* Set CRYP parameters */
- hcryp->Init.DataType = pConf->DataType;
- hcryp->Init.pKey = pConf->pKey;
- hcryp->Init.Algorithm = pConf->Algorithm;
- hcryp->Init.KeySize = pConf->KeySize;
- hcryp->Init.pInitVect = pConf->pInitVect;
- hcryp->Init.Header = pConf->Header;
- hcryp->Init.HeaderSize = pConf->HeaderSize;
- hcryp->Init.B0 = pConf->B0;
- hcryp->Init.DataWidthUnit = pConf->DataWidthUnit;
+ hcryp->Init.DataType = pConf->DataType;
+ hcryp->Init.pKey = pConf->pKey;
+ hcryp->Init.Algorithm = pConf->Algorithm;
+ hcryp->Init.KeySize = pConf->KeySize;
+ hcryp->Init.pInitVect = pConf->pInitVect;
+ hcryp->Init.Header = pConf->Header;
+ hcryp->Init.HeaderSize = pConf->HeaderSize;
+ hcryp->Init.B0 = pConf->B0;
+ hcryp->Init.DataWidthUnit = pConf->DataWidthUnit;
+ hcryp->Init.HeaderWidthUnit = pConf->HeaderWidthUnit;
+ hcryp->Init.KeyIVConfigSkip = pConf->KeyIVConfigSkip;
/* Set the key size (This bit field is do not care in the DES or TDES modes), data type and operating mode*/
MODIFY_REG(hcryp->Instance->CR, AES_CR_DATATYPE | AES_CR_KEYSIZE | AES_CR_CHMOD, hcryp->Init.DataType | hcryp->Init.KeySize | hcryp->Init.Algorithm);
@@ -661,7 +663,9 @@
pConf->Header = hcryp->Init.Header ;
pConf->HeaderSize = hcryp->Init.HeaderSize;
pConf->B0 = hcryp->Init.B0;
- pConf->DataWidthUnit = hcryp->Init.DataWidthUnit;
+ pConf->DataWidthUnit = hcryp->Init.DataWidthUnit;
+ pConf->HeaderWidthUnit = hcryp->Init.HeaderWidthUnit;
+ pConf->KeyIVConfigSkip = hcryp->Init.KeyIVConfigSkip;
/* Process Unlocked */
__HAL_UNLOCK(hcryp);
@@ -693,8 +697,8 @@
/* Prevent unused argument(s) compilation warning */
UNUSED(hcryp);
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_CRYP_MspInit could be implemented in the user file
+ /* NOTE : This function should not be modified; when the callback is needed,
+ the HAL_CRYP_MspInit can be implemented in the user file
*/
}
@@ -709,8 +713,8 @@
/* Prevent unused argument(s) compilation warning */
UNUSED(hcryp);
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_CRYP_MspDeInit could be implemented in the user file
+ /* NOTE : This function should not be modified; when the callback is needed,
+ the HAL_CRYP_MspDeInit can be implemented in the user file
*/
}
@@ -1929,8 +1933,8 @@
/* Prevent unused argument(s) compilation warning */
UNUSED(hcryp);
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_CRYP_InCpltCallback could be implemented in the user file
+ /* NOTE : This function should not be modified; when the callback is needed,
+ the HAL_CRYP_InCpltCallback can be implemented in the user file
*/
}
@@ -1945,8 +1949,8 @@
/* Prevent unused argument(s) compilation warning */
UNUSED(hcryp);
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_CRYP_OutCpltCallback could be implemented in the user file
+ /* NOTE : This function should not be modified; when the callback is needed,
+ the HAL_CRYP_OutCpltCallback can be implemented in the user file
*/
}
@@ -1961,8 +1965,8 @@
/* Prevent unused argument(s) compilation warning */
UNUSED(hcryp);
- /* NOTE : This function Should not be modified, when the callback is needed,
- the HAL_CRYP_ErrorCallback could be implemented in the user file
+ /* NOTE : This function should not be modified; when the callback is needed,
+ the HAL_CRYP_ErrorCallback can be implemented in the user file
*/
}
/**
@@ -2570,15 +2574,31 @@
/* Initiate payload DMA IN and processed data DMA OUT transfers */
(void)CRYP_GCMCCM_SetPayloadPhase_DMA(hcryp);
}
+ else
+ {
+ uint32_t algo;
+ /* ECB, CBC or CTR end of input data feeding
+ or
+ end of GCM/CCM payload data feeding through DMA */
+ algo = hcryp->Instance->CR & AES_CR_CHMOD;
- /* Call input data transfer complete callback */
+ /* Don't call input data transfer complete callback only if
+ it remains some input data to write to the peripheral.
+ This case can only occur for GCM and CCM with a payload length
+ not a multiple of 16 bytes */
+ if (!(((algo == CRYP_AES_GCM_GMAC) || (algo == CRYP_AES_CCM)) && \
+ (((hcryp->Size) % 16U) != 0U)))
+ {
+ /* Call input data transfer complete callback */
#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
- /*Call registered Input complete callback*/
- hcryp->InCpltCallback(hcryp);
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
#else
- /*Call legacy weak Input complete callback*/
- HAL_CRYP_InCpltCallback(hcryp);
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
+ }
+ } /* if (hcryp->Phase == CRYP_PHASE_HEADER_DMA_FEED) */
}
/**
@@ -2642,6 +2662,14 @@
hcryp->Instance->DINR = 0x0U;
count++;
}
+ /* Call input data transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
/*Wait on CCF flag*/
CRYP_ClearCCFlagWhenHigh(hcryp, CRYP_TIMEOUT_GCMCCMHEADERPHASE);
@@ -3380,7 +3408,7 @@
hcryp->CrypInCount++;
hcryp->Instance->DINR = *(uint32_t *)(hcryp->pCrypInBuffPtr + hcryp->CrypInCount);
hcryp->CrypInCount++;
- if (hcryp->CrypInCount == (hcryp->Size / 4U))
+ if ((hcryp->CrypInCount == (hcryp->Size / 4U)) && ((hcryp->Size % 16U) == 0U))
{
/* Call Input transfer complete callback */
#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
@@ -3431,6 +3459,14 @@
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
+ /* Call Input transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
}
/* Enter header data */
@@ -3470,15 +3506,6 @@
hcryp->CrypHeaderCount++;
}
}
-
- /* Call Input transfer complete callback */
-#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
- /*Call registered Input complete callback*/
- hcryp->InCpltCallback(hcryp);
-#else
- /*Call legacy weak Input complete callback*/
- HAL_CRYP_InCpltCallback(hcryp);
-#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
else
{
@@ -3528,7 +3555,7 @@
hcryp->CrypInCount++;
hcryp->Instance->DINR = *(uint32_t *)(hcryp->pCrypInBuffPtr + hcryp->CrypInCount);
hcryp->CrypInCount++;
- if (hcryp->CrypInCount == (hcryp->Size / 4U))
+ if ((hcryp->CrypInCount == (hcryp->Size / 4U)) && ((hcryp->Size % 16U) == 0U))
{
/* Call Input transfer complete callback */
#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
@@ -3579,6 +3606,14 @@
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
+ /* Call Input transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
}
@@ -3904,6 +3939,11 @@
uint32_t npblb;
uint32_t mode;
uint32_t DoKeyIVConfig = 1U; /* By default, carry out peripheral Key and IV configuration */
+ uint32_t headersize_in_bytes;
+ uint32_t tmp;
+ uint32_t mask[12] = {0x0U, 0xFF000000U, 0xFFFF0000U, 0xFFFFFF00U, /* 32-bit data type */
+ 0x0U, 0x0000FF00U, 0x0000FFFFU, 0xFF00FFFFU, /* 16-bit data type */
+ 0x0U, 0x000000FFU, 0x0000FFFFU, 0x00FFFFFFU}; /* 8-bit data type */
#if (USE_HAL_CRYP_SUSPEND_RESUME == 1U)
if ((hcryp->Phase == CRYP_PHASE_HEADER_SUSPENDED) || (hcryp->Phase == CRYP_PHASE_PAYLOAD_SUSPENDED))
@@ -3993,7 +4033,16 @@
/* Enable the CRYP peripheral */
__HAL_CRYP_ENABLE(hcryp);
- if (hcryp->Init.HeaderSize == 0U) /*header phase is skipped*/
+ if (hcryp->Init.HeaderWidthUnit == CRYP_HEADERWIDTHUNIT_WORD)
+ {
+ headersize_in_bytes = hcryp->Init.HeaderSize * 4U;
+ }
+ else
+ {
+ headersize_in_bytes = hcryp->Init.HeaderSize;
+ }
+
+ if (headersize_in_bytes == 0U) /* Header phase is skipped */
{
/* Set the phase */
hcryp->Phase = CRYP_PHASE_PROCESS;
@@ -4077,26 +4126,63 @@
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
+ /* Call Input transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
}
- else if ((hcryp->Init.HeaderSize) < 4U) /*HeaderSize < 4 */
+ /* Enter header data */
+ /* Check first whether header length is small enough to enter the full header in one shot */
+ else if (headersize_in_bytes <= 16U)
{
- /* Last block optionally pad the data with zeros*/
- for (loopcounter = 0U; loopcounter < (hcryp->Init.HeaderSize % 4U); loopcounter++)
+ for (loopcounter = 0U; (loopcounter < (headersize_in_bytes / 4U)); loopcounter++)
{
hcryp->Instance->DINR = *(uint32_t *)(hcryp->Init.Header + hcryp->CrypHeaderCount);
hcryp->CrypHeaderCount++ ;
}
+ /* If the header size is a multiple of words */
+ if ((headersize_in_bytes % 4U) == 0U)
+ {
+ /* Pad the data with zeros to have a complete block */
+ while (loopcounter < 4U)
+ {
+ hcryp->Instance->DINR = 0x0U;
+ loopcounter++;
+ }
+ }
+ else
+ {
+ /* Enter last bytes, padded with zeros */
+ tmp = *(uint32_t *)(hcryp->Init.Header + hcryp->CrypHeaderCount);
+ tmp &= mask[(hcryp->Init.DataType * 2U) + (headersize_in_bytes % 4U)];
+ hcryp->Instance->DINR = tmp;
+ hcryp->CrypHeaderCount++;
+ loopcounter++;
+ /* Pad the data with zeros to have a complete block */
while (loopcounter < 4U)
{
- /* pad the data with zeros to have a complete block */
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
}
+ /* Call Input transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
+ }
else
{
- /* Write the input block in the IN FIFO */
+ /* Write the first input header block in the Input FIFO,
+ the following header data will be fed after interrupt occurrence */
hcryp->Instance->DINR = *(uint32_t *)(hcryp->Init.Header + hcryp->CrypHeaderCount);
hcryp->CrypHeaderCount++;
hcryp->Instance->DINR = *(uint32_t *)(hcryp->Init.Header + hcryp->CrypHeaderCount);
@@ -4105,9 +4191,8 @@
hcryp->CrypHeaderCount++;
hcryp->Instance->DINR = *(uint32_t *)(hcryp->Init.Header + hcryp->CrypHeaderCount);
hcryp->CrypHeaderCount++;
- }
-
- } /* end of if (DoKeyIVConfig == 1U) */
+ }/* if (hcryp->Init.HeaderSize == 0U) */ /* Header phase is skipped*/
+ } /* end of if (dokeyivconfig == 1U) */
else /* Key and IV have already been configured,
header has already been processed;
only process here message payload */
@@ -4182,6 +4267,14 @@
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
+ /* Call Input transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
}
@@ -4387,9 +4480,9 @@
hcryp->CrypInCount++;
hcryp->Instance->DINR = *(uint32_t *)(hcryp->pCrypInBuffPtr + hcryp->CrypInCount);
hcryp->CrypInCount++;
- if ((hcryp->CrypInCount == hcryp->Size) && (hcryp->Init.Algorithm == CRYP_AES_GCM_GMAC))
+ if ((hcryp->CrypInCount == (hcryp->Size / 4U)) && ((hcryp->Size % 16U) == 0U))
{
- /* Call output transfer complete callback */
+ /* Call input transfer complete callback */
#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
/*Call registered Input complete callback*/
hcryp->InCpltCallback(hcryp);
@@ -4435,6 +4528,14 @@
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
+ /* Call input transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
}
@@ -4509,6 +4610,14 @@
hcryp->Instance->DINR = 0U;
index++;
}
+ /* Call the input data transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
/* Wait for CCF flag to be raised */
count = CRYP_TIMEOUT_GCMCCMHEADERPHASE;
do
@@ -4550,6 +4659,15 @@
/* Process unlocked */
__HAL_UNLOCK(hcryp);
+
+ /* Call Output transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Output complete callback*/
+ hcryp->OutCpltCallback(hcryp);
+#else
+ /*Call legacy weak Output complete callback*/
+ HAL_CRYP_OutCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
return HAL_OK;
@@ -4947,6 +5065,14 @@
hcryp->Instance->DINR = 0x0U;
loopcounter++;
}
+ /* Call the input data transfer complete callback */
+#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1U)
+ /*Call registered Input complete callback*/
+ hcryp->InCpltCallback(hcryp);
+#else
+ /*Call legacy weak Input complete callback*/
+ HAL_CRYP_InCpltCallback(hcryp);
+#endif /* USE_HAL_CRYP_REGISTER_CALLBACKS */
}
}
else if ((((headersize_in_bytes / 4U) - (hcryp->CrypHeaderCount)) >= 4U))
@@ -5398,9 +5524,9 @@
hcryp->CrypInCount++;
hcryp->Instance->DINR = *(uint32_t *)(hcryp->pCrypInBuffPtr + hcryp->CrypInCount );
hcryp->CrypInCount++;
- if((hcryp->CrypInCount == hcryp->Size) && (hcryp->Init.Algorithm == CRYP_AES_GCM_GMAC))
+ if ((hcryp->CrypInCount == (hcryp->Size / 4U)) && ((hcryp->Size % 16U) == 0U))
{
- /* Call output transfer complete callback */
+ /* Call input transfer complete callback */
#if (USE_HAL_CRYP_REGISTER_CALLBACKS == 1)
/*Call registered Input complete callback*/
hcryp->InCpltCallback(hcryp);
diff --git a/Src/stm32wlxx_hal_dac.c b/Src/stm32wlxx_hal_dac.c
index 377bad3..f712cd1 100644
--- a/Src/stm32wlxx_hal_dac.c
+++ b/Src/stm32wlxx_hal_dac.c
@@ -209,7 +209,7 @@
The compilation define USE_HAL_DAC_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.
- Use Functions @ref HAL_DAC_RegisterCallback() to register a user callback,
+ Use Functions HAL_DAC_RegisterCallback() to register a user callback,
it allows to register following callbacks:
(+) ConvCpltCallbackCh1 : callback when a half transfer is completed on Ch1.
(+) ConvHalfCpltCallbackCh1 : callback when a transfer is completed on Ch1.
@@ -220,7 +220,7 @@
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
- Use function @ref HAL_DAC_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_DAC_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function. It allows to reset following callbacks:
(+) ConvCpltCallbackCh1 : callback when a half transfer is completed on Ch1.
(+) ConvHalfCpltCallbackCh1 : callback when a transfer is completed on Ch1.
@@ -231,12 +231,12 @@
(+) All Callbacks
This function) takes as parameters the HAL peripheral handle and the Callback ID.
- By default, after the @ref HAL_DAC_Init and if the state is HAL_DAC_STATE_RESET
+ By default, after the HAL_DAC_Init and if the state is HAL_DAC_STATE_RESET
all callbacks are reset to the corresponding legacy weak (surcharged) functions.
Exception done for MspInit and MspDeInit callbacks that are respectively
- reset to the legacy weak (surcharged) functions in the @ref HAL_DAC_Init
- and @ref HAL_DAC_DeInit only when these callbacks are null (not registered beforehand).
- If not, MspInit or MspDeInit are not null, the @ref HAL_DAC_Init and @ref HAL_DAC_DeInit
+ reset to the legacy weak (surcharged) functions in the HAL_DAC_Init
+ and HAL_DAC_DeInit only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the HAL_DAC_Init and HAL_DAC_DeInit
keep and use the user MspInit/MspDeInit callbacks (registered beforehand)
Callbacks can be registered/unregistered in READY state only.
@@ -244,8 +244,8 @@
in READY or RESET state, thus registered (user) MspInit/DeInit callbacks can be used
during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_DAC_RegisterCallback before calling @ref HAL_DAC_DeInit
- or @ref HAL_DAC_Init function.
+ using HAL_DAC_RegisterCallback before calling HAL_DAC_DeInit
+ or HAL_DAC_Init function.
When The compilation define USE_HAL_DAC_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registering feature is not available
diff --git a/Src/stm32wlxx_hal_dma.c b/Src/stm32wlxx_hal_dma.c
index 74c8c99..ee221a4 100644
--- a/Src/stm32wlxx_hal_dma.c
+++ b/Src/stm32wlxx_hal_dma.c
@@ -1002,7 +1002,7 @@
This subsection provides functions allowing to
(+) Configure the DMA channel(s) privilege and non-privilege attributes
(+) Configure the DMA channel(s) secure and non-secure attributes from
- secure world when the system implements the security (TZEN=1)
+ secure world when the system implements the security (ESE=1)
(+) Get the DMA channel(s) attributes
@endverbatim
@@ -1142,7 +1142,7 @@
/**
* @brief Get the attribute of a DMA channel.
* @note Secure and non-secure attributes are only available from secure state
- * when the system implements the security (TZEN=1)
+ * when the system implements the security (ESE=1)
* @param hdma Pointer to a DMA_HandleTypeDef structure that contains
* the configuration information for the specified DMA Channel.
* @param ChannelAttributes pointer to return the attributes.
diff --git a/Src/stm32wlxx_hal_exti.c b/Src/stm32wlxx_hal_exti.c
index 9eb7e47..74bfae7 100644
--- a/Src/stm32wlxx_hal_exti.c
+++ b/Src/stm32wlxx_hal_exti.c
@@ -330,6 +330,10 @@
pExtiConfig->Mode |= EXTI_MODE_EVENT;
}
+ /* Get default Trigger and GPIOSel configuration */
+ pExtiConfig->Trigger = EXTI_TRIGGER_NONE;
+ pExtiConfig->GPIOSel = 0x00u;
+
/* 2] Get trigger for configurable lines : rising */
if ((pExtiConfig->Line & EXTI_CONFIG) != 0x00u)
{
@@ -341,10 +345,6 @@
{
pExtiConfig->Trigger = EXTI_TRIGGER_RISING;
}
- else
- {
- pExtiConfig->Trigger = EXTI_TRIGGER_NONE;
- }
/* Get falling configuration */
regaddr = (&EXTI->FTSR1 + (EXTI_CONFIG_OFFSET * offset));
@@ -362,15 +362,6 @@
regval = SYSCFG->EXTICR[linepos >> 2u];
pExtiConfig->GPIOSel = ((regval << (SYSCFG_EXTICR1_EXTI1_Pos * (3uL - (linepos & 0x03u)))) >> 24u);
}
- else
- {
- pExtiConfig->GPIOSel = 0x00u;
- }
- }
- else
- {
- pExtiConfig->Trigger = EXTI_TRIGGER_NONE;
- pExtiConfig->GPIOSel = 0x00u;
}
return HAL_OK;
diff --git a/Src/stm32wlxx_hal_gpio.c b/Src/stm32wlxx_hal_gpio.c
index d11d3dc..a51154c 100644
--- a/Src/stm32wlxx_hal_gpio.c
+++ b/Src/stm32wlxx_hal_gpio.c
@@ -117,17 +117,9 @@
/* Private typedef -----------------------------------------------------------*/
/* Private defines ------------------------------------------------------------*/
-/** @defgroup GPIO_Private_Constants GPIO Private Constants
+/** @addtogroup GPIO_Private_Constants GPIO Private Constants
* @{
*/
-#define GPIO_MODE (0x00000003U)
-#define EXTI_MODE (0x10000000U)
-#define GPIO_MODE_IT (0x00010000U)
-#define GPIO_MODE_EVT (0x00020000U)
-#define RISING_EDGE (0x00100000U)
-#define FALLING_EDGE (0x00200000U)
-#define GPIO_OUTPUT_TYPE (0x00000010U)
-
#define GPIO_NUMBER (16U)
/**
* @}
@@ -183,8 +175,7 @@
{
/*--------------------- GPIO Mode Configuration ------------------------*/
/* In case of Output or Alternate function mode selection */
- if ((GPIO_Init->Mode == GPIO_MODE_OUTPUT_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_PP) ||
- (GPIO_Init->Mode == GPIO_MODE_OUTPUT_OD) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
+ if (((GPIO_Init->Mode & GPIO_MODE) == MODE_OUTPUT) || ((GPIO_Init->Mode & GPIO_MODE) == MODE_AF))
{
/* Check the Speed parameter */
assert_param(IS_GPIO_SPEED(GPIO_Init->Speed));
@@ -197,18 +188,21 @@
/* Configure the IO Output Type */
temp = GPIOx->OTYPER;
temp &= ~(GPIO_OTYPER_OT0 << position) ;
- temp |= (((GPIO_Init->Mode & GPIO_OUTPUT_TYPE) >> 4U) << position);
+ temp |= (((GPIO_Init->Mode & OUTPUT_TYPE) >> OUTPUT_TYPE_Pos) << position);
GPIOx->OTYPER = temp;
}
/* Activate the Pull-up or Pull down resistor for the current IO */
- temp = GPIOx->PUPDR;
- temp &= ~(GPIO_PUPDR_PUPD0 << (position * 2U));
- temp |= ((GPIO_Init->Pull) << (position * 2U));
- GPIOx->PUPDR = temp;
+ if ((GPIO_Init->Mode & GPIO_MODE) != MODE_ANALOG)
+ {
+ temp = GPIOx->PUPDR;
+ temp &= ~(GPIO_PUPDR_PUPD0 << (position * 2U));
+ temp |= ((GPIO_Init->Pull) << (position * 2U));
+ GPIOx->PUPDR = temp;
+ }
/* In case of Alternate function mode selection */
- if ((GPIO_Init->Mode == GPIO_MODE_AF_PP) || (GPIO_Init->Mode == GPIO_MODE_AF_OD))
+ if ((GPIO_Init->Mode & GPIO_MODE) == MODE_AF)
{
/* Check the Alternate function parameters */
assert_param(IS_GPIO_AF_INSTANCE(GPIOx));
@@ -229,7 +223,7 @@
/*--------------------- EXTI Mode Configuration ------------------------*/
/* Configure the External Interrupt or event for the current IO */
- if ((GPIO_Init->Mode & EXTI_MODE) == EXTI_MODE)
+ if ((GPIO_Init->Mode & EXTI_MODE) != 0x00u)
{
temp = SYSCFG->EXTICR[position >> 2u];
temp &= ~(0x07uL << (4U * (position & 0x03U)));
@@ -243,7 +237,7 @@
temp = EXTI->IMR1;
#endif /* CORE_CM0PLUS */
temp &= ~(iocurrent);
- if ((GPIO_Init->Mode & GPIO_MODE_IT) == GPIO_MODE_IT)
+ if ((GPIO_Init->Mode & EXTI_IT) != 0x00u)
{
temp |= iocurrent;
}
@@ -259,7 +253,7 @@
temp = EXTI->EMR1;
#endif /* CORE_CM0PLUS */
temp &= ~(iocurrent);
- if ((GPIO_Init->Mode & GPIO_MODE_EVT) == GPIO_MODE_EVT)
+ if ((GPIO_Init->Mode & EXTI_EVT) != 0x00u)
{
temp |= iocurrent;
}
@@ -272,7 +266,7 @@
/* Clear Rising Falling edge configuration */
temp = EXTI->RTSR1;
temp &= ~(iocurrent);
- if ((GPIO_Init->Mode & RISING_EDGE) == RISING_EDGE)
+ if ((GPIO_Init->Mode & TRIGGER_RISING) != 0x00u)
{
temp |= iocurrent;
}
@@ -280,7 +274,7 @@
temp = EXTI->FTSR1;
temp &= ~(iocurrent);
- if ((GPIO_Init->Mode & FALLING_EDGE) == FALLING_EDGE)
+ if ((GPIO_Init->Mode & TRIGGER_FALLING) != 0x00u)
{
temp |= iocurrent;
}
diff --git a/Src/stm32wlxx_hal_gtzc.c b/Src/stm32wlxx_hal_gtzc.c
index 36677c9..fee8189 100644
--- a/Src/stm32wlxx_hal_gtzc.c
+++ b/Src/stm32wlxx_hal_gtzc.c
@@ -15,16 +15,16 @@
##### GTZC main features #####
==============================================================================
[..]
- (+) Global TrustZone Controller (GTZC) composed of two sub-blocks:
- (++) TZSC: TrustZone security controller
+ (+) Global Security Controller (GTZC) composed of two sub-blocks:
+ (++) TZSC: Security controller
This sub-block defines the secure/privileged state of slave
peripherals. It also controls the unprivileged area size for the
watermark memory peripheral controller (MPCWM).
- (++) TZIC: TrustZone illegal access controller
+ (++) TZIC: Security Illegal access controller
This sub-block gathers all illegal access events in the system and
generates a secure interrupt towards the secure CPU2 NVIC.
- (+) These sub-blocks are used to configure TrustZone system security and
+ (+) These sub-blocks are used to configure system security and
privilege such as:
(++) on-chip Flash memory and RAM with programmable secure or privilege or
both area
@@ -112,7 +112,7 @@
==============================================================================
[..]
This section provides functions allowing to initialize/configure TZSC
- TZSC: TrustZone Security Controller
+ TZSC: Security Controller
@endverbatim
* @{
*/
@@ -503,7 +503,7 @@
[..]
This section provides functions allowing to manage the common TZSC and TZSC-MPCWM lock.
It includes lock enable, and current value read.
- TZSC: TrustZone Security Controller
+ TZSC: Security Controller
MPCWM: Memory Protection Controller WaterMark
@endverbatim
* @{
@@ -544,7 +544,7 @@
==============================================================================
[..]
This section provides functions allowing to initialize/configure TZIC
- TZIC: Trust Zone Interrupt Controller
+ TZIC: Security Interrupt Controller
@endverbatim
* @{
*/
diff --git a/Src/stm32wlxx_hal_hsem.c b/Src/stm32wlxx_hal_hsem.c
index 8b3d736..1f3bc93 100644
--- a/Src/stm32wlxx_hal_hsem.c
+++ b/Src/stm32wlxx_hal_hsem.c
@@ -20,15 +20,15 @@
==============================================================================
[..]
(#)Take a semaphore In 2-Step mode Using function HAL_HSEM_Take. This function takes as parameters :
- (++) the semaphore ID from 0 to 31
+ (++) the semaphore ID from 0 to 15
(++) the process ID from 0 to 255
(#) Fast Take semaphore In 1-Step mode Using function HAL_HSEM_FastTake. This function takes as parameter :
- (++) the semaphore ID from 0_ID to 31. Note that the process ID value is implicitly assumed as zero
+ (++) the semaphore ID from 0 to 15. Note that the process ID value is implicitly assumed as zero
(#) Check if a semaphore is Taken using function HAL_HSEM_IsSemTaken. This function takes as parameter :
- (++) the semaphore ID from 0_ID to 31
+ (++) the semaphore ID from 0 to 15
(++) It returns 1 if the given semaphore is taken otherwise (Free) zero
(#)Release a semaphore using function with HAL_HSEM_Release. This function takes as parameters :
- (++) the semaphore ID from 0 to 31
+ (++) the semaphore ID from 0 to 15
(++) the process ID from 0 to 255:
(++) Note: If ProcessID and MasterID match, semaphore is freed, and an interrupt
may be generated when enabled (notification activated). If ProcessID or MasterID does not match,
@@ -144,7 +144,7 @@
/**
* @brief Take a semaphore in 2 Step mode.
- * @param SemID: semaphore ID from 0 to 31
+ * @param SemID: semaphore ID from 0 to 15
* @param ProcessID: Process ID from 0 to 255
* @retval HAL status
*/
@@ -170,7 +170,7 @@
/**
* @brief Fast Take a semaphore with 1 Step mode.
- * @param SemID: semaphore ID from 0 to 31
+ * @param SemID: semaphore ID from 0 to 15
* @retval HAL status
*/
HAL_StatusTypeDef HAL_HSEM_FastTake(uint32_t SemID)
@@ -201,7 +201,7 @@
/**
* @brief Release a semaphore.
- * @param SemID: semaphore ID from 0 to 31
+ * @param SemID: semaphore ID from 0 to 15
* @param ProcessID: Process ID from 0 to 255
* @retval None
*/
diff --git a/Src/stm32wlxx_hal_i2c.c b/Src/stm32wlxx_hal_i2c.c
index 17feea7..1bf9eb7 100644
--- a/Src/stm32wlxx_hal_i2c.c
+++ b/Src/stm32wlxx_hal_i2c.c
@@ -19,7 +19,7 @@
(#) Declare a I2C_HandleTypeDef handle structure, for example:
I2C_HandleTypeDef hi2c;
- (#)Initialize the I2C low level resources by implementing the @ref HAL_I2C_MspInit() API:
+ (#)Initialize the I2C low level resources by implementing the HAL_I2C_MspInit() API:
(##) Enable the I2Cx interface clock
(##) I2C pins configuration
(+++) Enable the clock for the I2C GPIOs
@@ -28,7 +28,8 @@
(+++) Configure the I2Cx interrupt priority
(+++) Enable the NVIC I2C IRQ Channel
(##) DMA Configuration if you need to use DMA process
- (+++) Declare a DMA_HandleTypeDef handle structure for the transmit or receive channel
+ (+++) Declare a DMA_HandleTypeDef handle structure for
+ the transmit or receive channel
(+++) Enable the DMAx interface clock using
(+++) Configure the DMA handle parameters
(+++) Configure the DMA Tx or Rx channel
@@ -39,49 +40,49 @@
(#) Configure the Communication Clock Timing, Own Address1, Master Addressing mode, Dual Addressing mode,
Own Address2, Own Address2 Mask, General call and Nostretch mode in the hi2c Init structure.
- (#) Initialize the I2C registers by calling the @ref HAL_I2C_Init(), configures also the low level Hardware
- (GPIO, CLOCK, NVIC...etc) by calling the customized @ref HAL_I2C_MspInit(&hi2c) API.
+ (#) Initialize the I2C registers by calling the HAL_I2C_Init(), configures also the low level Hardware
+ (GPIO, CLOCK, NVIC...etc) by calling the customized HAL_I2C_MspInit(&hi2c) API.
- (#) To check if target device is ready for communication, use the function @ref HAL_I2C_IsDeviceReady()
+ (#) To check if target device is ready for communication, use the function HAL_I2C_IsDeviceReady()
(#) For I2C IO and IO MEM operations, three operation modes are available within this driver :
*** Polling mode IO operation ***
=================================
[..]
- (+) Transmit in master mode an amount of data in blocking mode using @ref HAL_I2C_Master_Transmit()
- (+) Receive in master mode an amount of data in blocking mode using @ref HAL_I2C_Master_Receive()
- (+) Transmit in slave mode an amount of data in blocking mode using @ref HAL_I2C_Slave_Transmit()
- (+) Receive in slave mode an amount of data in blocking mode using @ref HAL_I2C_Slave_Receive()
+ (+) Transmit in master mode an amount of data in blocking mode using HAL_I2C_Master_Transmit()
+ (+) Receive in master mode an amount of data in blocking mode using HAL_I2C_Master_Receive()
+ (+) Transmit in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Transmit()
+ (+) Receive in slave mode an amount of data in blocking mode using HAL_I2C_Slave_Receive()
*** Polling mode IO MEM operation ***
=====================================
[..]
- (+) Write an amount of data in blocking mode to a specific memory address using @ref HAL_I2C_Mem_Write()
- (+) Read an amount of data in blocking mode from a specific memory address using @ref HAL_I2C_Mem_Read()
+ (+) Write an amount of data in blocking mode to a specific memory address using HAL_I2C_Mem_Write()
+ (+) Read an amount of data in blocking mode from a specific memory address using HAL_I2C_Mem_Read()
*** Interrupt mode IO operation ***
===================================
[..]
- (+) Transmit in master mode an amount of data in non-blocking mode using @ref HAL_I2C_Master_Transmit_IT()
- (+) At transmission end of transfer, @ref HAL_I2C_MasterTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MasterTxCpltCallback()
- (+) Receive in master mode an amount of data in non-blocking mode using @ref HAL_I2C_Master_Receive_IT()
- (+) At reception end of transfer, @ref HAL_I2C_MasterRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MasterRxCpltCallback()
- (+) Transmit in slave mode an amount of data in non-blocking mode using @ref HAL_I2C_Slave_Transmit_IT()
- (+) At transmission end of transfer, @ref HAL_I2C_SlaveTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_SlaveTxCpltCallback()
- (+) Receive in slave mode an amount of data in non-blocking mode using @ref HAL_I2C_Slave_Receive_IT()
- (+) At reception end of transfer, @ref HAL_I2C_SlaveRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_SlaveRxCpltCallback()
- (+) In case of transfer Error, @ref HAL_I2C_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_ErrorCallback()
- (+) Abort a master I2C process communication with Interrupt using @ref HAL_I2C_Master_Abort_IT()
- (+) End of abort process, @ref HAL_I2C_AbortCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_AbortCpltCallback()
- (+) Discard a slave I2C process communication using @ref __HAL_I2C_GENERATE_NACK() macro.
+ (+) Transmit in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Transmit_IT()
+ (+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MasterTxCpltCallback()
+ (+) Receive in master mode an amount of data in non-blocking mode using HAL_I2C_Master_Receive_IT()
+ (+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MasterRxCpltCallback()
+ (+) Transmit in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Transmit_IT()
+ (+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback()
+ (+) Receive in slave mode an amount of data in non-blocking mode using HAL_I2C_Slave_Receive_IT()
+ (+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback()
+ (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can
+ add their own code by customization of function pointer HAL_I2C_ErrorCallback()
+ (+) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
+ (+) End of abort process, HAL_I2C_AbortCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_AbortCpltCallback()
+ (+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro.
This action will inform Master to generate a Stop condition to discard the communication.
@@ -92,120 +93,137 @@
when a direction change during transfer
[..]
(+) A specific option field manage the different steps of a sequential transfer
- (+) Option field values are defined through @ref I2C_XFEROPTIONS and are listed below:
- (++) I2C_FIRST_AND_LAST_FRAME: No sequential usage, functional is same as associated interfaces in no sequential mode
+ (+) Option field values are defined through I2C_XFEROPTIONS and are listed below:
+ (++) I2C_FIRST_AND_LAST_FRAME: No sequential usage, functional is same as associated interfaces in
+ no sequential mode
(++) I2C_FIRST_FRAME: Sequential usage, this option allow to manage a sequence with start condition, address
and data to transfer without a final stop condition
- (++) I2C_FIRST_AND_NEXT_FRAME: Sequential usage (Master only), this option allow to manage a sequence with start condition, address
- and data to transfer without a final stop condition, an then permit a call the same master sequential interface
- several times (like @ref HAL_I2C_Master_Seq_Transmit_IT() then @ref HAL_I2C_Master_Seq_Transmit_IT()
- or @ref HAL_I2C_Master_Seq_Transmit_DMA() then @ref HAL_I2C_Master_Seq_Transmit_DMA())
+ (++) I2C_FIRST_AND_NEXT_FRAME: Sequential usage (Master only), this option allow to manage a sequence with
+ start condition, address and data to transfer without a final stop condition,
+ an then permit a call the same master sequential interface several times
+ (like HAL_I2C_Master_Seq_Transmit_IT() then HAL_I2C_Master_Seq_Transmit_IT()
+ or HAL_I2C_Master_Seq_Transmit_DMA() then HAL_I2C_Master_Seq_Transmit_DMA())
(++) I2C_NEXT_FRAME: Sequential usage, this option allow to manage a sequence with a restart condition, address
- and with new data to transfer if the direction change or manage only the new data to transfer
+ and with new data to transfer if the direction change or manage only the new data to
+ transfer
if no direction change and without a final stop condition in both cases
(++) I2C_LAST_FRAME: Sequential usage, this option allow to manage a sequance with a restart condition, address
- and with new data to transfer if the direction change or manage only the new data to transfer
+ and with new data to transfer if the direction change or manage only the new data to
+ transfer
if no direction change and with a final stop condition in both cases
- (++) I2C_LAST_FRAME_NO_STOP: Sequential usage (Master only), this option allow to manage a restart condition after several call of the same master sequential
- interface several times (link with option I2C_FIRST_AND_NEXT_FRAME).
- Usage can, transfer several bytes one by one using HAL_I2C_Master_Seq_Transmit_IT(option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME)
- or HAL_I2C_Master_Seq_Receive_IT(option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME)
- or HAL_I2C_Master_Seq_Transmit_DMA(option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME)
- or HAL_I2C_Master_Seq_Receive_DMA(option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME).
- Then usage of this option I2C_LAST_FRAME_NO_STOP at the last Transmit or Receive sequence permit to call the opposite interface Receive or Transmit
+ (++) I2C_LAST_FRAME_NO_STOP: Sequential usage (Master only), this option allow to manage a restart condition
+ after several call of the same master sequential interface several times
+ (link with option I2C_FIRST_AND_NEXT_FRAME).
+ Usage can, transfer several bytes one by one using
+ HAL_I2C_Master_Seq_Transmit_IT
+ or HAL_I2C_Master_Seq_Receive_IT
+ or HAL_I2C_Master_Seq_Transmit_DMA
+ or HAL_I2C_Master_Seq_Receive_DMA
+ with option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME.
+ Then usage of this option I2C_LAST_FRAME_NO_STOP at the last Transmit or
+ Receive sequence permit to call the opposite interface Receive or Transmit
without stopping the communication and so generate a restart condition.
- (++) I2C_OTHER_FRAME: Sequential usage (Master only), this option allow to manage a restart condition after each call of the same master sequential
+ (++) I2C_OTHER_FRAME: Sequential usage (Master only), this option allow to manage a restart condition after
+ each call of the same master sequential
interface.
- Usage can, transfer several bytes one by one with a restart with slave address between each bytes using HAL_I2C_Master_Seq_Transmit_IT(option I2C_FIRST_FRAME then I2C_OTHER_FRAME)
- or HAL_I2C_Master_Seq_Receive_IT(option I2C_FIRST_FRAME then I2C_OTHER_FRAME)
- or HAL_I2C_Master_Seq_Transmit_DMA(option I2C_FIRST_FRAME then I2C_OTHER_FRAME)
- or HAL_I2C_Master_Seq_Receive_DMA(option I2C_FIRST_FRAME then I2C_OTHER_FRAME).
- Then usage of this option I2C_OTHER_AND_LAST_FRAME at the last frame to help automatic generation of STOP condition.
+ Usage can, transfer several bytes one by one with a restart with slave address between
+ each bytes using
+ HAL_I2C_Master_Seq_Transmit_IT
+ or HAL_I2C_Master_Seq_Receive_IT
+ or HAL_I2C_Master_Seq_Transmit_DMA
+ or HAL_I2C_Master_Seq_Receive_DMA
+ with option I2C_FIRST_FRAME then I2C_OTHER_FRAME.
+ Then usage of this option I2C_OTHER_AND_LAST_FRAME at the last frame to help automatic
+ generation of STOP condition.
(+) Different sequential I2C interfaces are listed below:
- (++) Sequential transmit in master I2C mode an amount of data in non-blocking mode using @ref HAL_I2C_Master_Seq_Transmit_IT()
- or using @ref HAL_I2C_Master_Seq_Transmit_DMA()
- (+++) At transmission end of current frame transfer, @ref HAL_I2C_MasterTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MasterTxCpltCallback()
- (++) Sequential receive in master I2C mode an amount of data in non-blocking mode using @ref HAL_I2C_Master_Seq_Receive_IT()
- or using @ref HAL_I2C_Master_Seq_Receive_DMA()
- (+++) At reception end of current frame transfer, @ref HAL_I2C_MasterRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MasterRxCpltCallback()
- (++) Abort a master IT or DMA I2C process communication with Interrupt using @ref HAL_I2C_Master_Abort_IT()
- (+++) End of abort process, @ref HAL_I2C_AbortCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_AbortCpltCallback()
- (++) Enable/disable the Address listen mode in slave I2C mode using @ref HAL_I2C_EnableListen_IT() @ref HAL_I2C_DisableListen_IT()
- (+++) When address slave I2C match, @ref HAL_I2C_AddrCallback() is executed and user can
- add his own code to check the Address Match Code and the transmission direction request by master (Write/Read).
- (+++) At Listen mode end @ref HAL_I2C_ListenCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_ListenCpltCallback()
- (++) Sequential transmit in slave I2C mode an amount of data in non-blocking mode using @ref HAL_I2C_Slave_Seq_Transmit_IT()
- or using @ref HAL_I2C_Slave_Seq_Transmit_DMA()
- (+++) At transmission end of current frame transfer, @ref HAL_I2C_SlaveTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_SlaveTxCpltCallback()
- (++) Sequential receive in slave I2C mode an amount of data in non-blocking mode using @ref HAL_I2C_Slave_Seq_Receive_IT()
- or using @ref HAL_I2C_Slave_Seq_Receive_DMA()
- (+++) At reception end of current frame transfer, @ref HAL_I2C_SlaveRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_SlaveRxCpltCallback()
- (++) In case of transfer Error, @ref HAL_I2C_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_ErrorCallback()
- (++) Discard a slave I2C process communication using @ref __HAL_I2C_GENERATE_NACK() macro.
+ (++) Sequential transmit in master I2C mode an amount of data in non-blocking mode using
+ HAL_I2C_Master_Seq_Transmit_IT() or using HAL_I2C_Master_Seq_Transmit_DMA()
+ (+++) At transmission end of current frame transfer, HAL_I2C_MasterTxCpltCallback() is executed and
+ users can add their own code by customization of function pointer HAL_I2C_MasterTxCpltCallback()
+ (++) Sequential receive in master I2C mode an amount of data in non-blocking mode using
+ HAL_I2C_Master_Seq_Receive_IT() or using HAL_I2C_Master_Seq_Receive_DMA()
+ (+++) At reception end of current frame transfer, HAL_I2C_MasterRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MasterRxCpltCallback()
+ (++) Abort a master IT or DMA I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
+ (+++) End of abort process, HAL_I2C_AbortCpltCallback() is executed and users can
+ add their own code by customization of function pointerHAL_I2C_AbortCpltCallback()
+ (++) Enable/disable the Address listen mode in slave I2C mode using HAL_I2C_EnableListen_IT()
+ HAL_I2C_DisableListen_IT()
+ (+++) When address slave I2C match, HAL_I2C_AddrCallback() is executed and users can
+ add their own code to check the Address Match Code and the transmission direction request by master
+ (Write/Read).
+ (+++) At Listen mode end HAL_I2C_ListenCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_ListenCpltCallback()
+ (++) Sequential transmit in slave I2C mode an amount of data in non-blocking mode using
+ HAL_I2C_Slave_Seq_Transmit_IT()
+ or using HAL_I2C_Slave_Seq_Transmit_DMA()
+ (+++) At transmission end of current frame transfer, HAL_I2C_SlaveTxCpltCallback() is executed and
+ users can add their own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback()
+ (++) Sequential receive in slave I2C mode an amount of data in non-blocking mode using
+ HAL_I2C_Slave_Seq_Receive_IT()
+ or usingHAL_I2C_Slave_Seq_Receive_DMA()
+ (+++) At reception end of current frame transfer, HAL_I2C_SlaveRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback()
+ (++) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can
+ add their own code by customization of function pointer HAL_I2C_ErrorCallback()
+ (++) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro.
This action will inform Master to generate a Stop condition to discard the communication.
*** Interrupt mode IO MEM operation ***
=======================================
[..]
(+) Write an amount of data in non-blocking mode with Interrupt to a specific memory address using
- @ref HAL_I2C_Mem_Write_IT()
- (+) At Memory end of write transfer, @ref HAL_I2C_MemTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MemTxCpltCallback()
+ HAL_I2C_Mem_Write_IT()
+ (+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MemTxCpltCallback()
(+) Read an amount of data in non-blocking mode with Interrupt from a specific memory address using
- @ref HAL_I2C_Mem_Read_IT()
- (+) At Memory end of read transfer, @ref HAL_I2C_MemRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MemRxCpltCallback()
- (+) In case of transfer Error, @ref HAL_I2C_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_ErrorCallback()
+ HAL_I2C_Mem_Read_IT()
+ (+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MemRxCpltCallback()
+ (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can
+ add their own code by customization of function pointer HAL_I2C_ErrorCallback()
*** DMA mode IO operation ***
==============================
[..]
(+) Transmit in master mode an amount of data in non-blocking mode (DMA) using
- @ref HAL_I2C_Master_Transmit_DMA()
- (+) At transmission end of transfer, @ref HAL_I2C_MasterTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MasterTxCpltCallback()
+ HAL_I2C_Master_Transmit_DMA()
+ (+) At transmission end of transfer, HAL_I2C_MasterTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MasterTxCpltCallback()
(+) Receive in master mode an amount of data in non-blocking mode (DMA) using
- @ref HAL_I2C_Master_Receive_DMA()
- (+) At reception end of transfer, @ref HAL_I2C_MasterRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MasterRxCpltCallback()
+ HAL_I2C_Master_Receive_DMA()
+ (+) At reception end of transfer, HAL_I2C_MasterRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MasterRxCpltCallback()
(+) Transmit in slave mode an amount of data in non-blocking mode (DMA) using
- @ref HAL_I2C_Slave_Transmit_DMA()
- (+) At transmission end of transfer, @ref HAL_I2C_SlaveTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_SlaveTxCpltCallback()
+ HAL_I2C_Slave_Transmit_DMA()
+ (+) At transmission end of transfer, HAL_I2C_SlaveTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_SlaveTxCpltCallback()
(+) Receive in slave mode an amount of data in non-blocking mode (DMA) using
- @ref HAL_I2C_Slave_Receive_DMA()
- (+) At reception end of transfer, @ref HAL_I2C_SlaveRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_SlaveRxCpltCallback()
- (+) In case of transfer Error, @ref HAL_I2C_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_ErrorCallback()
- (+) Abort a master I2C process communication with Interrupt using @ref HAL_I2C_Master_Abort_IT()
- (+) End of abort process, @ref HAL_I2C_AbortCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_AbortCpltCallback()
- (+) Discard a slave I2C process communication using @ref __HAL_I2C_GENERATE_NACK() macro.
+ HAL_I2C_Slave_Receive_DMA()
+ (+) At reception end of transfer, HAL_I2C_SlaveRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_SlaveRxCpltCallback()
+ (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can
+ add their own code by customization of function pointer HAL_I2C_ErrorCallback()
+ (+) Abort a master I2C process communication with Interrupt using HAL_I2C_Master_Abort_IT()
+ (+) End of abort process, HAL_I2C_AbortCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_AbortCpltCallback()
+ (+) Discard a slave I2C process communication using __HAL_I2C_GENERATE_NACK() macro.
This action will inform Master to generate a Stop condition to discard the communication.
*** DMA mode IO MEM operation ***
=================================
[..]
(+) Write an amount of data in non-blocking mode with DMA to a specific memory address using
- @ref HAL_I2C_Mem_Write_DMA()
- (+) At Memory end of write transfer, @ref HAL_I2C_MemTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MemTxCpltCallback()
+ HAL_I2C_Mem_Write_DMA()
+ (+) At Memory end of write transfer, HAL_I2C_MemTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MemTxCpltCallback()
(+) Read an amount of data in non-blocking mode with DMA from a specific memory address using
- @ref HAL_I2C_Mem_Read_DMA()
- (+) At Memory end of read transfer, @ref HAL_I2C_MemRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_MemRxCpltCallback()
- (+) In case of transfer Error, @ref HAL_I2C_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_I2C_ErrorCallback()
+ HAL_I2C_Mem_Read_DMA()
+ (+) At Memory end of read transfer, HAL_I2C_MemRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_I2C_MemRxCpltCallback()
+ (+) In case of transfer Error, HAL_I2C_ErrorCallback() function is executed and users can
+ add their own code by customization of function pointer HAL_I2C_ErrorCallback()
*** I2C HAL driver macros list ***
@@ -213,23 +231,23 @@
[..]
Below the list of most used macros in I2C HAL driver.
- (+) @ref __HAL_I2C_ENABLE: Enable the I2C peripheral
- (+) @ref __HAL_I2C_DISABLE: Disable the I2C peripheral
- (+) @ref __HAL_I2C_GENERATE_NACK: Generate a Non-Acknowledge I2C peripheral in Slave mode
- (+) @ref __HAL_I2C_GET_FLAG: Check whether the specified I2C flag is set or not
- (+) @ref __HAL_I2C_CLEAR_FLAG: Clear the specified I2C pending flag
- (+) @ref __HAL_I2C_ENABLE_IT: Enable the specified I2C interrupt
- (+) @ref __HAL_I2C_DISABLE_IT: Disable the specified I2C interrupt
+ (+) __HAL_I2C_ENABLE: Enable the I2C peripheral
+ (+) __HAL_I2C_DISABLE: Disable the I2C peripheral
+ (+) __HAL_I2C_GENERATE_NACK: Generate a Non-Acknowledge I2C peripheral in Slave mode
+ (+) __HAL_I2C_GET_FLAG: Check whether the specified I2C flag is set or not
+ (+) __HAL_I2C_CLEAR_FLAG: Clear the specified I2C pending flag
+ (+) __HAL_I2C_ENABLE_IT: Enable the specified I2C interrupt
+ (+) __HAL_I2C_DISABLE_IT: Disable the specified I2C interrupt
*** Callback registration ***
=============================================
[..]
The compilation flag USE_HAL_I2C_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.
- Use Functions @ref HAL_I2C_RegisterCallback() or @ref HAL_I2C_RegisterAddrCallback()
+ Use Functions HAL_I2C_RegisterCallback() or HAL_I2C_RegisterAddrCallback()
to register an interrupt callback.
[..]
- Function @ref HAL_I2C_RegisterCallback() allows to register following callbacks:
+ Function HAL_I2C_RegisterCallback() allows to register following callbacks:
(+) MasterTxCpltCallback : callback for Master transmission end of transfer.
(+) MasterRxCpltCallback : callback for Master reception end of transfer.
(+) SlaveTxCpltCallback : callback for Slave transmission end of transfer.
@@ -244,11 +262,11 @@
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
[..]
- For specific callback AddrCallback use dedicated register callbacks : @ref HAL_I2C_RegisterAddrCallback().
+ For specific callback AddrCallback use dedicated register callbacks : HAL_I2C_RegisterAddrCallback().
[..]
- Use function @ref HAL_I2C_UnRegisterCallback to reset a callback to the default
+ Use function HAL_I2C_UnRegisterCallback to reset a callback to the default
weak function.
- @ref HAL_I2C_UnRegisterCallback takes as parameters the HAL peripheral handle,
+ HAL_I2C_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) MasterTxCpltCallback : callback for Master transmission end of transfer.
@@ -263,24 +281,24 @@
(+) MspInitCallback : callback for Msp Init.
(+) MspDeInitCallback : callback for Msp DeInit.
[..]
- For callback AddrCallback use dedicated register callbacks : @ref HAL_I2C_UnRegisterAddrCallback().
+ For callback AddrCallback use dedicated register callbacks : HAL_I2C_UnRegisterAddrCallback().
[..]
- By default, after the @ref HAL_I2C_Init() and when the state is @ref HAL_I2C_STATE_RESET
+ By default, after the HAL_I2C_Init() and when the state is HAL_I2C_STATE_RESET
all callbacks are set to the corresponding weak functions:
- examples @ref HAL_I2C_MasterTxCpltCallback(), @ref HAL_I2C_MasterRxCpltCallback().
+ examples HAL_I2C_MasterTxCpltCallback(), HAL_I2C_MasterRxCpltCallback().
Exception done for MspInit and MspDeInit functions that are
- reset to the legacy weak functions in the @ref HAL_I2C_Init()/ @ref HAL_I2C_DeInit() only when
+ reset to the legacy weak functions in the HAL_I2C_Init()/ HAL_I2C_DeInit() only when
these callbacks are null (not registered beforehand).
- If MspInit or MspDeInit are not null, the @ref HAL_I2C_Init()/ @ref HAL_I2C_DeInit()
+ If MspInit or MspDeInit are not null, the HAL_I2C_Init()/ HAL_I2C_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
[..]
- Callbacks can be registered/unregistered in @ref HAL_I2C_STATE_READY state only.
+ Callbacks can be registered/unregistered in HAL_I2C_STATE_READY state only.
Exception done MspInit/MspDeInit functions that can be registered/unregistered
- in @ref HAL_I2C_STATE_READY or @ref HAL_I2C_STATE_RESET state,
+ in HAL_I2C_STATE_READY or HAL_I2C_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
Then, the user first registers the MspInit/MspDeInit user callbacks
- using @ref HAL_I2C_RegisterCallback() before calling @ref HAL_I2C_DeInit()
- or @ref HAL_I2C_Init() function.
+ using HAL_I2C_RegisterCallback() before calling HAL_I2C_DeInit()
+ or HAL_I2C_Init() function.
[..]
When the compilation flag USE_HAL_I2C_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available and all callbacks
@@ -336,28 +354,48 @@
#define I2C_TIMEOUT_FLAG (25U) /*!< 25 ms */
#define MAX_NBYTE_SIZE 255U
-#define SlaveAddr_SHIFT 7U
-#define SlaveAddr_MSK 0x06U
+#define SLAVE_ADDR_SHIFT 7U
+#define SLAVE_ADDR_MSK 0x06U
/* Private define for @ref PreviousState usage */
-#define I2C_STATE_MSK ((uint32_t)((uint32_t)((uint32_t)HAL_I2C_STATE_BUSY_TX | (uint32_t)HAL_I2C_STATE_BUSY_RX) & (uint32_t)(~((uint32_t)HAL_I2C_STATE_READY)))) /*!< Mask State define, keep only RX and TX bits */
-#define I2C_STATE_NONE ((uint32_t)(HAL_I2C_MODE_NONE)) /*!< Default Value */
-#define I2C_STATE_MASTER_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | (uint32_t)HAL_I2C_MODE_MASTER)) /*!< Master Busy TX, combinaison of State LSB and Mode enum */
-#define I2C_STATE_MASTER_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | (uint32_t)HAL_I2C_MODE_MASTER)) /*!< Master Busy RX, combinaison of State LSB and Mode enum */
-#define I2C_STATE_SLAVE_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | (uint32_t)HAL_I2C_MODE_SLAVE)) /*!< Slave Busy TX, combinaison of State LSB and Mode enum */
-#define I2C_STATE_SLAVE_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | (uint32_t)HAL_I2C_MODE_SLAVE)) /*!< Slave Busy RX, combinaison of State LSB and Mode enum */
-#define I2C_STATE_MEM_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | (uint32_t)HAL_I2C_MODE_MEM)) /*!< Memory Busy TX, combinaison of State LSB and Mode enum */
-#define I2C_STATE_MEM_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | (uint32_t)HAL_I2C_MODE_MEM)) /*!< Memory Busy RX, combinaison of State LSB and Mode enum */
+#define I2C_STATE_MSK ((uint32_t)((uint32_t)((uint32_t)HAL_I2C_STATE_BUSY_TX | \
+ (uint32_t)HAL_I2C_STATE_BUSY_RX) & \
+ (uint32_t)(~((uint32_t)HAL_I2C_STATE_READY))))
+/*!< Mask State define, keep only RX and TX bits */
+#define I2C_STATE_NONE ((uint32_t)(HAL_I2C_MODE_NONE))
+/*!< Default Value */
+#define I2C_STATE_MASTER_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | \
+ (uint32_t)HAL_I2C_MODE_MASTER))
+/*!< Master Busy TX, combinaison of State LSB and Mode enum */
+#define I2C_STATE_MASTER_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | \
+ (uint32_t)HAL_I2C_MODE_MASTER))
+/*!< Master Busy RX, combinaison of State LSB and Mode enum */
+#define I2C_STATE_SLAVE_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | \
+ (uint32_t)HAL_I2C_MODE_SLAVE))
+/*!< Slave Busy TX, combinaison of State LSB and Mode enum */
+#define I2C_STATE_SLAVE_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | \
+ (uint32_t)HAL_I2C_MODE_SLAVE))
+/*!< Slave Busy RX, combinaison of State LSB and Mode enum */
+#define I2C_STATE_MEM_BUSY_TX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_TX & I2C_STATE_MSK) | \
+ (uint32_t)HAL_I2C_MODE_MEM))
+/*!< Memory Busy TX, combinaison of State LSB and Mode enum */
+#define I2C_STATE_MEM_BUSY_RX ((uint32_t)(((uint32_t)HAL_I2C_STATE_BUSY_RX & I2C_STATE_MSK) | \
+ (uint32_t)HAL_I2C_MODE_MEM))
+/*!< Memory Busy RX, combinaison of State LSB and Mode enum */
/* Private define to centralize the enable/disable of Interrupts */
-#define I2C_XFER_TX_IT (uint16_t)(0x0001U) /* Bit field can be combinated with @ref I2C_XFER_LISTEN_IT */
-#define I2C_XFER_RX_IT (uint16_t)(0x0002U) /* Bit field can be combinated with @ref I2C_XFER_LISTEN_IT */
-#define I2C_XFER_LISTEN_IT (uint16_t)(0x8000U) /* Bit field can be combinated with @ref I2C_XFER_TX_IT and @ref I2C_XFER_RX_IT */
+#define I2C_XFER_TX_IT (uint16_t)(0x0001U) /*!< Bit field can be combinated with
+ @ref I2C_XFER_LISTEN_IT */
+#define I2C_XFER_RX_IT (uint16_t)(0x0002U) /*!< Bit field can be combinated with
+ @ref I2C_XFER_LISTEN_IT */
+#define I2C_XFER_LISTEN_IT (uint16_t)(0x8000U) /*!< Bit field can be combinated with @ref I2C_XFER_TX_IT
+ and @ref I2C_XFER_RX_IT */
-#define I2C_XFER_ERROR_IT (uint16_t)(0x0010U) /* Bit definition to manage addition of global Error and NACK treatment */
-#define I2C_XFER_CPLT_IT (uint16_t)(0x0020U) /* Bit definition to manage only STOP evenement */
-#define I2C_XFER_RELOAD_IT (uint16_t)(0x0040U) /* Bit definition to manage only Reload of NBYTE */
+#define I2C_XFER_ERROR_IT (uint16_t)(0x0010U) /*!< Bit definition to manage addition of global Error
+ and NACK treatment */
+#define I2C_XFER_CPLT_IT (uint16_t)(0x0020U) /*!< Bit definition to manage only STOP evenement */
+#define I2C_XFER_RELOAD_IT (uint16_t)(0x0040U) /*!< Bit definition to manage only Reload of NBYTE */
/* Private define Sequential Transfer Options default/reset value */
#define I2C_NO_OPTION_FRAME (0xFFFF0000U)
@@ -390,24 +428,34 @@
static void I2C_ITError(I2C_HandleTypeDef *hi2c, uint32_t ErrorCode);
/* Private functions to handle IT transfer */
-static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
- uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart);
-static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
- uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart);
+static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress,
+ uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout,
+ uint32_t Tickstart);
+static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress,
+ uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout,
+ uint32_t Tickstart);
/* Private functions for I2C transfer IRQ handler */
-static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
-static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
-static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
-static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources);
+static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources);
+static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources);
+static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources);
+static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources);
/* Private functions to handle flags during polling transfer */
static HAL_StatusTypeDef I2C_WaitOnFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Flag, FlagStatus Status,
uint32_t Timeout, uint32_t Tickstart);
-static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
-static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
-static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
-static HAL_StatusTypeDef I2C_IsAcknowledgeFailed(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart);
+static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart);
+static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart);
+static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart);
+static HAL_StatusTypeDef I2C_IsAcknowledgeFailed(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart);
/* Private functions to centralize the enable/disable of Interrupts */
static void I2C_Enable_IRQ(I2C_HandleTypeDef *hi2c, uint16_t InterruptRequest);
@@ -559,7 +607,8 @@
hi2c->Instance->OAR2 &= ~I2C_DUALADDRESS_ENABLE;
/* Configure I2Cx: Dual mode and Own Address2 */
- hi2c->Instance->OAR2 = (hi2c->Init.DualAddressMode | hi2c->Init.OwnAddress2 | (hi2c->Init.OwnAddress2Masks << 8));
+ hi2c->Instance->OAR2 = (hi2c->Init.DualAddressMode | hi2c->Init.OwnAddress2 | \
+ (hi2c->Init.OwnAddress2Masks << 8));
/*---------------------------- I2Cx CR1 Configuration ----------------------*/
/* Configure I2Cx: Generalcall and NoStretch mode */
@@ -1065,8 +1114,8 @@
* @param Timeout Timeout duration
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size,
- uint32_t Timeout)
+HAL_StatusTypeDef HAL_I2C_Master_Transmit(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+ uint16_t Size, uint32_t Timeout)
{
uint32_t tickstart;
@@ -1097,12 +1146,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_GENERATE_START_WRITE);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_WRITE);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_WRITE);
}
while (hi2c->XferCount > 0U)
@@ -1132,12 +1183,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_NO_STARTSTOP);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_NO_STARTSTOP);
}
}
}
@@ -1180,8 +1233,8 @@
* @param Timeout Timeout duration
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size,
- uint32_t Timeout)
+HAL_StatusTypeDef HAL_I2C_Master_Receive(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+ uint16_t Size, uint32_t Timeout)
{
uint32_t tickstart;
@@ -1212,12 +1265,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_READ);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_GENERATE_START_READ);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_READ);
}
while (hi2c->XferCount > 0U)
@@ -1248,12 +1303,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_NO_STARTSTOP);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_NO_STARTSTOP);
}
}
}
@@ -1294,7 +1351,8 @@
* @param Timeout Timeout duration
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout)
+HAL_StatusTypeDef HAL_I2C_Slave_Transmit(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+ uint32_t Timeout)
{
uint32_t tickstart;
@@ -1431,7 +1489,8 @@
* @param Timeout Timeout duration
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size, uint32_t Timeout)
+HAL_StatusTypeDef HAL_I2C_Slave_Receive(I2C_HandleTypeDef *hi2c, uint8_t *pData, uint16_t Size,
+ uint32_t Timeout)
{
uint32_t tickstart;
@@ -1606,7 +1665,8 @@
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
return HAL_OK;
@@ -1627,7 +1687,8 @@
* @param Size Amount of data to be sent
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData, uint16_t Size)
+HAL_StatusTypeDef HAL_I2C_Master_Receive_IT(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint8_t *pData,
+ uint16_t Size)
{
uint32_t xfermode;
@@ -1675,7 +1736,8 @@
/* Enable ERR, TC, STOP, NACK, RXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT);
return HAL_OK;
@@ -1724,7 +1786,8 @@
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT | I2C_XFER_LISTEN_IT);
return HAL_OK;
@@ -1773,7 +1836,8 @@
/* Enable ERR, TC, STOP, NACK, RXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT | I2C_XFER_LISTEN_IT);
return HAL_OK;
@@ -1846,7 +1910,8 @@
hi2c->hdmatx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR,
+ hi2c->XferSize);
}
else
{
@@ -1906,7 +1971,8 @@
/* Send Slave Address */
/* Set NBYTES to write and generate START condition */
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_WRITE);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_WRITE);
/* Process Unlocked */
__HAL_UNLOCK(hi2c);
@@ -1916,7 +1982,8 @@
process unlock */
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
}
@@ -1990,7 +2057,8 @@
hi2c->hdmarx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData,
+ hi2c->XferSize);
}
else
{
@@ -2050,7 +2118,8 @@
/* Send Slave Address */
/* Set NBYTES to read and generate START condition */
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_READ);
/* Process Unlocked */
__HAL_UNLOCK(hi2c);
@@ -2060,7 +2129,8 @@
process unlock */
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
}
@@ -2118,7 +2188,8 @@
hi2c->hdmatx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR,
+ hi2c->XferSize);
}
else
{
@@ -2221,7 +2292,8 @@
hi2c->hdmarx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData,
+ hi2c->XferSize);
}
else
{
@@ -2374,12 +2446,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_NO_STARTSTOP);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_NO_STARTSTOP);
}
}
@@ -2474,12 +2548,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE, I2C_GENERATE_START_READ);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_GENERATE_START_READ);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_READ);
}
do
@@ -2510,12 +2586,14 @@
if (hi2c->XferCount > MAX_NBYTE_SIZE)
{
hi2c->XferSize = MAX_NBYTE_SIZE;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t) hi2c->XferSize, I2C_RELOAD_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t) hi2c->XferSize, I2C_RELOAD_MODE,
+ I2C_NO_STARTSTOP);
}
else
{
hi2c->XferSize = hi2c->XferCount;
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_NO_STARTSTOP);
}
}
} while (hi2c->XferCount > 0U);
@@ -2608,7 +2686,8 @@
}
/* Send Slave Address and Memory Address */
- if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK)
+ if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart)
+ != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(hi2c);
@@ -2627,7 +2706,8 @@
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
return HAL_OK;
@@ -2719,7 +2799,8 @@
/* Enable ERR, TC, STOP, NACK, RXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_RX_IT);
return HAL_OK;
@@ -2792,7 +2873,8 @@
}
/* Send Slave Address and Memory Address */
- if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart) != HAL_OK)
+ if (I2C_RequestMemoryWrite(hi2c, DevAddress, MemAddress, MemAddSize, I2C_TIMEOUT_FLAG, tickstart)
+ != HAL_OK)
{
/* Process Unlocked */
__HAL_UNLOCK(hi2c);
@@ -2813,7 +2895,8 @@
hi2c->hdmatx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR,
+ hi2c->XferSize);
}
else
{
@@ -2957,7 +3040,8 @@
hi2c->hdmarx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData,
+ hi2c->XferSize);
}
else
{
@@ -3028,7 +3112,8 @@
* @param Timeout Timeout duration
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials, uint32_t Timeout)
+HAL_StatusTypeDef HAL_I2C_IsDeviceReady(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint32_t Trials,
+ uint32_t Timeout)
{
uint32_t tickstart;
@@ -3205,9 +3290,11 @@
xfermode = hi2c->XferOptions;
}
- /* If transfer direction not change and there is no request to start another frame, do not generate Restart Condition */
+ /* If transfer direction not change and there is no request to start another frame,
+ do not generate Restart Condition */
/* Mean Previous state is same as current state */
- if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX) && (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
+ if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX) && \
+ (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
{
xferrequest = I2C_NO_STARTSTOP;
}
@@ -3291,9 +3378,11 @@
xfermode = hi2c->XferOptions;
}
- /* If transfer direction not change and there is no request to start another frame, do not generate Restart Condition */
+ /* If transfer direction not change and there is no request to start another frame,
+ do not generate Restart Condition */
/* Mean Previous state is same as current state */
- if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX) && (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
+ if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_TX) && \
+ (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
{
xferrequest = I2C_NO_STARTSTOP;
}
@@ -3324,7 +3413,8 @@
hi2c->hdmatx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR,
+ hi2c->XferSize);
}
else
{
@@ -3383,7 +3473,8 @@
/* Send Slave Address */
/* Set NBYTES to write and generate START condition */
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_WRITE);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_WRITE);
/* Process Unlocked */
__HAL_UNLOCK(hi2c);
@@ -3393,7 +3484,8 @@
process unlock */
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
}
@@ -3453,9 +3545,11 @@
xfermode = hi2c->XferOptions;
}
- /* If transfer direction not change and there is no request to start another frame, do not generate Restart Condition */
+ /* If transfer direction not change and there is no request to start another frame,
+ do not generate Restart Condition */
/* Mean Previous state is same as current state */
- if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) && (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
+ if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) && \
+ (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
{
xferrequest = I2C_NO_STARTSTOP;
}
@@ -3539,9 +3633,11 @@
xfermode = hi2c->XferOptions;
}
- /* If transfer direction not change and there is no request to start another frame, do not generate Restart Condition */
+ /* If transfer direction not change and there is no request to start another frame,
+ do not generate Restart Condition */
/* Mean Previous state is same as current state */
- if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) && (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
+ if ((hi2c->PreviousState == I2C_STATE_MASTER_BUSY_RX) && \
+ (IS_I2C_TRANSFER_OTHER_OPTIONS_REQUEST(XferOptions) == 0))
{
xferrequest = I2C_NO_STARTSTOP;
}
@@ -3572,7 +3668,8 @@
hi2c->hdmarx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData,
+ hi2c->XferSize);
}
else
{
@@ -3631,7 +3728,8 @@
/* Send Slave Address */
/* Set NBYTES to read and generate START condition */
- I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_GENERATE_START_READ);
+ I2C_TransferConfig(hi2c, DevAddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE,
+ I2C_GENERATE_START_READ);
/* Process Unlocked */
__HAL_UNLOCK(hi2c);
@@ -3641,7 +3739,8 @@
process unlock */
/* Enable ERR, TC, STOP, NACK, TXI interrupt */
/* possible to enable all of these */
- /* I2C_IT_ERRI | I2C_IT_TCI| I2C_IT_STOPI| I2C_IT_NACKI | I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
+ /* I2C_IT_ERRI | I2C_IT_TCI | I2C_IT_STOPI | I2C_IT_NACKI |
+ I2C_IT_ADDRI | I2C_IT_RXI | I2C_IT_TXI */
I2C_Enable_IRQ(hi2c, I2C_XFER_TX_IT);
}
@@ -3862,7 +3961,8 @@
hi2c->hdmatx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)pData, (uint32_t)&hi2c->Instance->TXDR,
+ hi2c->XferSize);
}
else
{
@@ -4138,7 +4238,8 @@
hi2c->hdmarx->XferAbortCallback = NULL;
/* Enable the DMA channel */
- dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)pData, hi2c->XferSize);
+ dmaxferstatus = HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR,
+ (uint32_t)pData, hi2c->XferSize);
}
else
{
@@ -4356,7 +4457,8 @@
uint32_t tmperror;
/* I2C Bus error interrupt occurred ------------------------------------*/
- if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_BERR) != RESET) && (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET))
+ if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_BERR) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET))
{
hi2c->ErrorCode |= HAL_I2C_ERROR_BERR;
@@ -4365,7 +4467,8 @@
}
/* I2C Over-Run/Under-Run interrupt occurred ----------------------------------------*/
- if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_OVR) != RESET) && (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET))
+ if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_OVR) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET))
{
hi2c->ErrorCode |= HAL_I2C_ERROR_OVR;
@@ -4374,7 +4477,8 @@
}
/* I2C Arbitration Loss error interrupt occurred -------------------------------------*/
- if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_ARLO) != RESET) && (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET))
+ if ((I2C_CHECK_FLAG(itflags, I2C_FLAG_ARLO) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(itsources, I2C_IT_ERRI) != RESET))
{
hi2c->ErrorCode |= HAL_I2C_ERROR_ARLO;
@@ -4628,7 +4732,8 @@
* @param ITSources Interrupt sources enabled.
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
+static HAL_StatusTypeDef I2C_Master_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources)
{
uint16_t devaddress;
uint32_t tmpITFlags = ITFlags;
@@ -4636,7 +4741,8 @@
/* Process Locked */
__HAL_LOCK(hi2c);
- if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
+ if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
{
/* Clear NACK Flag */
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
@@ -4649,7 +4755,8 @@
/* Flush TX register */
I2C_Flush_TXDR(hi2c);
}
- else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET))
+ else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET))
{
/* Remove RXNE flag on temporary variable as read done */
tmpITFlags &= ~I2C_FLAG_RXNE;
@@ -4663,7 +4770,8 @@
hi2c->XferSize--;
hi2c->XferCount--;
}
- else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET))
+ else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET))
{
/* Write data to TXDR */
hi2c->Instance->TXDR = *hi2c->pBuffPtr;
@@ -4674,7 +4782,8 @@
hi2c->XferSize--;
hi2c->XferCount--;
}
- else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TCR) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
+ else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TCR) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
{
if ((hi2c->XferCount != 0U) && (hi2c->XferSize == 0U))
{
@@ -4690,11 +4799,13 @@
hi2c->XferSize = hi2c->XferCount;
if (hi2c->XferOptions != I2C_NO_OPTION_FRAME)
{
- I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize, hi2c->XferOptions, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize,
+ hi2c->XferOptions, I2C_NO_STARTSTOP);
}
else
{
- I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize, I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
+ I2C_TransferConfig(hi2c, devaddress, (uint8_t)hi2c->XferSize,
+ I2C_AUTOEND_MODE, I2C_NO_STARTSTOP);
}
}
}
@@ -4714,7 +4825,8 @@
}
}
}
- else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TC) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
+ else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TC) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
{
if (hi2c->XferCount == 0U)
{
@@ -4745,7 +4857,8 @@
/* Nothing to do */
}
- if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
+ if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
{
/* Call I2C Master complete process */
I2C_ITMasterCplt(hi2c, tmpITFlags);
@@ -4765,7 +4878,8 @@
* @param ITSources Interrupt sources enabled.
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
+static HAL_StatusTypeDef I2C_Slave_ISR_IT(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources)
{
uint32_t tmpoptions = hi2c->XferOptions;
uint32_t tmpITFlags = ITFlags;
@@ -4774,13 +4888,15 @@
__HAL_LOCK(hi2c);
/* Check if STOPF is set */
- if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
+ if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_STOPF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
{
/* Call I2C Slave complete process */
I2C_ITSlaveCplt(hi2c, tmpITFlags);
}
- if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
+ if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_AF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
{
/* Check that I2C transfer finished */
/* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */
@@ -4788,8 +4904,9 @@
/* So clear Flag NACKF only */
if (hi2c->XferCount == 0U)
{
- /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for Warning[Pa134]: left and right operands are identical */
if ((hi2c->State == HAL_I2C_STATE_LISTEN) && (tmpoptions == I2C_FIRST_AND_LAST_FRAME))
+ /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for
+ Warning[Pa134]: left and right operands are identical */
{
/* Call I2C Listen complete process */
I2C_ITListenCplt(hi2c, tmpITFlags);
@@ -4828,7 +4945,8 @@
}
}
}
- else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET))
+ else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_RXNE) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_RXI) != RESET))
{
if (hi2c->XferCount > 0U)
{
@@ -4854,7 +4972,8 @@
{
I2C_ITAddrCplt(hi2c, tmpITFlags);
}
- else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET))
+ else if ((I2C_CHECK_FLAG(tmpITFlags, I2C_FLAG_TXIS) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TXI) != RESET))
{
/* Write data to TXDR only if XferCount not reach "0" */
/* A TXIS flag can be set, during STOP treatment */
@@ -4900,7 +5019,8 @@
* @param ITSources Interrupt sources enabled.
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
+static HAL_StatusTypeDef I2C_Master_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources)
{
uint16_t devaddress;
uint32_t xfermode;
@@ -4908,7 +5028,8 @@
/* Process Locked */
__HAL_LOCK(hi2c);
- if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
+ if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
{
/* Clear NACK Flag */
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
@@ -4924,7 +5045,8 @@
/* Flush TX register */
I2C_Flush_TXDR(hi2c);
}
- else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TCR) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
+ else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TCR) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
{
/* Disable TC interrupt */
__HAL_I2C_DISABLE_IT(hi2c, I2C_IT_TCI);
@@ -4985,7 +5107,8 @@
}
}
}
- else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TC) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
+ else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_TC) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_TCI) != RESET))
{
if (hi2c->XferCount == 0U)
{
@@ -5011,7 +5134,8 @@
I2C_ITError(hi2c, HAL_I2C_ERROR_SIZE);
}
}
- else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
+ else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
{
/* Call I2C Master complete process */
I2C_ITMasterCplt(hi2c, ITFlags);
@@ -5035,7 +5159,8 @@
* @param ITSources Interrupt sources enabled.
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags, uint32_t ITSources)
+static HAL_StatusTypeDef I2C_Slave_ISR_DMA(struct __I2C_HandleTypeDef *hi2c, uint32_t ITFlags,
+ uint32_t ITSources)
{
uint32_t tmpoptions = hi2c->XferOptions;
uint32_t treatdmanack = 0U;
@@ -5045,13 +5170,15 @@
__HAL_LOCK(hi2c);
/* Check if STOPF is set */
- if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
+ if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_STOPF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_STOPI) != RESET))
{
/* Call I2C Slave complete process */
I2C_ITSlaveCplt(hi2c, ITFlags);
}
- if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
+ if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_AF) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_NACKI) != RESET))
{
/* Check that I2C transfer finished */
/* if yes, normal use case, a NACK is sent by the MASTER when Transfer is finished */
@@ -5086,8 +5213,9 @@
if (treatdmanack == 1U)
{
- /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for Warning[Pa134]: left and right operands are identical */
if ((hi2c->State == HAL_I2C_STATE_LISTEN) && (tmpoptions == I2C_FIRST_AND_LAST_FRAME))
+ /* Same action must be done for (tmpoptions == I2C_LAST_FRAME) which removed for
+ Warning[Pa134]: left and right operands are identical */
{
/* Call I2C Listen complete process */
I2C_ITListenCplt(hi2c, ITFlags);
@@ -5148,7 +5276,8 @@
__HAL_I2C_CLEAR_FLAG(hi2c, I2C_FLAG_AF);
}
}
- else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_ADDR) != RESET) && (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_ADDRI) != RESET))
+ else if ((I2C_CHECK_FLAG(ITFlags, I2C_FLAG_ADDR) != RESET) && \
+ (I2C_CHECK_IT_SOURCE(ITSources, I2C_IT_ADDRI) != RESET))
{
I2C_ITAddrCplt(hi2c, ITFlags);
}
@@ -5175,8 +5304,9 @@
* @param Tickstart Tick start value
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
- uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart)
+static HAL_StatusTypeDef I2C_RequestMemoryWrite(I2C_HandleTypeDef *hi2c, uint16_t DevAddress,
+ uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout,
+ uint32_t Tickstart)
{
I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_RELOAD_MODE, I2C_GENERATE_START_WRITE);
@@ -5229,8 +5359,9 @@
* @param Tickstart Tick start value
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress, uint16_t MemAddress,
- uint16_t MemAddSize, uint32_t Timeout, uint32_t Tickstart)
+static HAL_StatusTypeDef I2C_RequestMemoryRead(I2C_HandleTypeDef *hi2c, uint16_t DevAddress,
+ uint16_t MemAddress, uint16_t MemAddSize, uint32_t Timeout,
+ uint32_t Tickstart)
{
I2C_TransferConfig(hi2c, DevAddress, (uint8_t)MemAddSize, I2C_SOFTEND_MODE, I2C_GENERATE_START_WRITE);
@@ -5298,7 +5429,7 @@
/* If 10bits addressing mode is selected */
if (hi2c->Init.AddressingMode == I2C_ADDRESSINGMODE_10BIT)
{
- if ((slaveaddrcode & SlaveAddr_MSK) == ((ownadd1code >> SlaveAddr_SHIFT) & SlaveAddr_MSK))
+ if ((slaveaddrcode & SLAVE_ADDR_MSK) == ((ownadd1code >> SLAVE_ADDR_SHIFT) & SLAVE_ADDR_MSK))
{
slaveaddrcode = ownadd1code;
hi2c->AddrEventCount++;
@@ -6025,7 +6156,8 @@
*/
static void I2C_DMAMasterTransmitCplt(DMA_HandleTypeDef *hdma)
{
- I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
+ /* Derogation MISRAC2012-Rule-11.5 */
+ I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent);
/* Disable DMA Request */
hi2c->Instance->CR1 &= ~I2C_CR1_TXDMAEN;
@@ -6053,7 +6185,8 @@
}
/* Enable the DMA channel */
- if (HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, (uint32_t)&hi2c->Instance->TXDR, hi2c->XferSize) != HAL_OK)
+ if (HAL_DMA_Start_IT(hi2c->hdmatx, (uint32_t)hi2c->pBuffPtr, (uint32_t)&hi2c->Instance->TXDR,
+ hi2c->XferSize) != HAL_OK)
{
/* Call the corresponding callback to inform upper layer of End of Transfer */
I2C_ITError(hi2c, HAL_I2C_ERROR_DMA);
@@ -6073,7 +6206,8 @@
*/
static void I2C_DMASlaveTransmitCplt(DMA_HandleTypeDef *hdma)
{
- I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
+ /* Derogation MISRAC2012-Rule-11.5 */
+ I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent);
uint32_t tmpoptions = hi2c->XferOptions;
if ((tmpoptions == I2C_NEXT_FRAME) || (tmpoptions == I2C_FIRST_FRAME))
@@ -6100,7 +6234,8 @@
*/
static void I2C_DMAMasterReceiveCplt(DMA_HandleTypeDef *hdma)
{
- I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
+ /* Derogation MISRAC2012-Rule-11.5 */
+ I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent);
/* Disable DMA Request */
hi2c->Instance->CR1 &= ~I2C_CR1_RXDMAEN;
@@ -6128,7 +6263,8 @@
}
/* Enable the DMA channel */
- if (HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)hi2c->pBuffPtr, hi2c->XferSize) != HAL_OK)
+ if (HAL_DMA_Start_IT(hi2c->hdmarx, (uint32_t)&hi2c->Instance->RXDR, (uint32_t)hi2c->pBuffPtr,
+ hi2c->XferSize) != HAL_OK)
{
/* Call the corresponding callback to inform upper layer of End of Transfer */
I2C_ITError(hi2c, HAL_I2C_ERROR_DMA);
@@ -6148,7 +6284,8 @@
*/
static void I2C_DMASlaveReceiveCplt(DMA_HandleTypeDef *hdma)
{
- I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
+ /* Derogation MISRAC2012-Rule-11.5 */
+ I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent);
uint32_t tmpoptions = hi2c->XferOptions;
if ((__HAL_DMA_GET_COUNTER(hi2c->hdmarx) == 0U) && \
@@ -6175,7 +6312,8 @@
*/
static void I2C_DMAError(DMA_HandleTypeDef *hdma)
{
- I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
+ /* Derogation MISRAC2012-Rule-11.5 */
+ I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent);
/* Disable Acknowledge */
hi2c->Instance->CR2 |= I2C_CR2_NACK;
@@ -6192,7 +6330,8 @@
*/
static void I2C_DMAAbort(DMA_HandleTypeDef *hdma)
{
- I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
+ /* Derogation MISRAC2012-Rule-11.5 */
+ I2C_HandleTypeDef *hi2c = (I2C_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent);
/* Reset AbortCpltCallback */
if (hi2c->hdmatx != NULL)
@@ -6248,7 +6387,8 @@
* @param Tickstart Tick start value
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
+static HAL_StatusTypeDef I2C_WaitOnTXISFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart)
{
while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_TXIS) == RESET)
{
@@ -6285,7 +6425,8 @@
* @param Tickstart Tick start value
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
+static HAL_StatusTypeDef I2C_WaitOnSTOPFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart)
{
while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET)
{
@@ -6319,7 +6460,8 @@
* @param Tickstart Tick start value
* @retval HAL status
*/
-static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout, uint32_t Tickstart)
+static HAL_StatusTypeDef I2C_WaitOnRXNEFlagUntilTimeout(I2C_HandleTypeDef *hi2c, uint32_t Timeout,
+ uint32_t Tickstart)
{
while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_RXNE) == RESET)
{
@@ -6386,6 +6528,12 @@
{
if (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_AF) == SET)
{
+ /* In case of Soft End condition, generate the STOP condition */
+ if (I2C_GET_STOP_MODE(hi2c) != I2C_AUTOEND_MODE)
+ {
+ /* Generate Stop */
+ hi2c->Instance->CR2 |= I2C_CR2_STOP;
+ }
/* Wait until STOP Flag is reset */
/* AutoEnd should be initiate after AF */
while (__HAL_I2C_GET_FLAG(hi2c, I2C_FLAG_STOPF) == RESET)
@@ -6461,9 +6609,11 @@
/* update CR2 register */
MODIFY_REG(hi2c->Instance->CR2,
((I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | \
- (I2C_CR2_RD_WRN & (uint32_t)(Request >> (31U - I2C_CR2_RD_WRN_Pos))) | I2C_CR2_START | I2C_CR2_STOP)), \
- (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) |
- (((uint32_t)Size << I2C_CR2_NBYTES_Pos) & I2C_CR2_NBYTES) | (uint32_t)Mode | (uint32_t)Request));
+ (I2C_CR2_RD_WRN & (uint32_t)(Request >> (31U - I2C_CR2_RD_WRN_Pos))) | \
+ I2C_CR2_START | I2C_CR2_STOP)), \
+ (uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | \
+ (((uint32_t)Size << I2C_CR2_NBYTES_Pos) & I2C_CR2_NBYTES) | \
+ (uint32_t)Mode | (uint32_t)Request));
}
/**
diff --git a/Src/stm32wlxx_hal_i2c_ex.c b/Src/stm32wlxx_hal_i2c_ex.c
index 189f884..bb03324 100644
--- a/Src/stm32wlxx_hal_i2c_ex.c
+++ b/Src/stm32wlxx_hal_i2c_ex.c
@@ -71,17 +71,15 @@
* @{
*/
-/** @defgroup I2CEx_Exported_Functions_Group1 Extended features functions
- * @brief Extended features functions
+/** @defgroup I2CEx_Exported_Functions_Group1 Filter Mode Functions
+ * @brief Filter Mode Functions
*
@verbatim
===============================================================================
- ##### Extended features functions #####
+ ##### Filter Mode Functions #####
===============================================================================
[..] This section provides functions allowing to:
(+) Configure Noise Filters
- (+) Configure Wake Up Feature
- (+) Configure Fast Mode Plus
@endverbatim
* @{
@@ -182,6 +180,23 @@
return HAL_BUSY;
}
}
+/**
+ * @}
+ */
+
+/** @defgroup I2CEx_Exported_Functions_Group2 WakeUp Mode Functions
+ * @brief WakeUp Mode Functions
+ *
+@verbatim
+ ===============================================================================
+ ##### WakeUp Mode Functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Configure Wake Up Feature
+
+@endverbatim
+ * @{
+ */
/**
* @brief Enable I2C wakeup from Stop mode(s).
@@ -260,6 +275,23 @@
return HAL_BUSY;
}
}
+/**
+ * @}
+ */
+
+/** @defgroup I2CEx_Exported_Functions_Group3 Fast Mode Plus Functions
+ * @brief Fast Mode Plus Functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Fast Mode Plus Functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+ (+) Configure Fast Mode Plus
+
+@endverbatim
+ * @{
+ */
/**
* @brief Enable the I2C fast mode plus driving capability.
@@ -308,7 +340,6 @@
/* Disable fast mode plus driving capability for selected pin */
CLEAR_BIT(SYSCFG->CFGR1, (uint32_t)ConfigFastModePlus);
}
-
/**
* @}
*/
diff --git a/Src/stm32wlxx_hal_i2s.c b/Src/stm32wlxx_hal_i2s.c
index e5336eb..8890e8a 100644
--- a/Src/stm32wlxx_hal_i2s.c
+++ b/Src/stm32wlxx_hal_i2s.c
@@ -741,7 +741,7 @@
* @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
* configuration phase, the Size parameter means the number of 16-bit data length
* in the transaction and when a 24-bit data frame or a 32-bit data frame is selected
- * the Size parameter means the number of 16-bit data length.
+ * the Size parameter means the number of 24-bit or 32-bit data length.
* @param Timeout Timeout duration
* @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization
* between Master and Slave(example: audio streaming).
@@ -858,7 +858,7 @@
* @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
* configuration phase, the Size parameter means the number of 16-bit data length
* in the transaction and when a 24-bit data frame or a 32-bit data frame is selected
- * the Size parameter means the number of 16-bit data length.
+ * the Size parameter means the number of 24-bit or 32-bit data length.
* @param Timeout Timeout duration
* @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization
* between Master and Slave(example: audio streaming).
@@ -959,7 +959,7 @@
* @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
* configuration phase, the Size parameter means the number of 16-bit data length
* in the transaction and when a 24-bit data frame or a 32-bit data frame is selected
- * the Size parameter means the number of 16-bit data length.
+ * the Size parameter means the number of 24-bit or 32-bit data length.
* @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization
* between Master and Slave(example: audio streaming).
* @retval HAL status
@@ -1023,7 +1023,7 @@
* @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
* configuration phase, the Size parameter means the number of 16-bit data length
* in the transaction and when a 24-bit data frame or a 32-bit data frame is selected
- * the Size parameter means the number of 16-bit data length.
+ * the Size parameter means the number of 24-bit or 32-bit data length.
* @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization
* between Master and Slave(example: audio streaming).
* @note It is recommended to use DMA for the I2S receiver to avoid de-synchronization
@@ -1089,7 +1089,7 @@
* @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
* configuration phase, the Size parameter means the number of 16-bit data length
* in the transaction and when a 24-bit data frame or a 32-bit data frame is selected
- * the Size parameter means the number of 16-bit data length.
+ * the Size parameter means the number of 24-bit or 32-bit data length.
* @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization
* between Master and Slave(example: audio streaming).
* @retval HAL status
@@ -1180,7 +1180,7 @@
* @note When a 16-bit data frame or a 16-bit data frame extended is selected during the I2S
* configuration phase, the Size parameter means the number of 16-bit data length
* in the transaction and when a 24-bit data frame or a 32-bit data frame is selected
- * the Size parameter means the number of 16-bit data length.
+ * the Size parameter means the number of 24-bit or 32-bit data length.
* @note The I2S is kept enabled at the end of transaction to avoid the clock de-synchronization
* between Master and Slave(example: audio streaming).
* @retval HAL status
diff --git a/Src/stm32wlxx_hal_irda.c b/Src/stm32wlxx_hal_irda.c
index e53a26a..5f5951d 100644
--- a/Src/stm32wlxx_hal_irda.c
+++ b/Src/stm32wlxx_hal_irda.c
@@ -113,8 +113,8 @@
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_IRDA_RegisterCallback() to register a user callback.
- Function @ref HAL_IRDA_RegisterCallback() allows to register following callbacks:
+ Use Function HAL_IRDA_RegisterCallback() to register a user callback.
+ Function HAL_IRDA_RegisterCallback() allows to register following callbacks:
(+) TxHalfCpltCallback : Tx Half Complete Callback.
(+) TxCpltCallback : Tx Complete Callback.
(+) RxHalfCpltCallback : Rx Half Complete Callback.
@@ -129,9 +129,9 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_IRDA_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_IRDA_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function.
- @ref HAL_IRDA_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ HAL_IRDA_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) TxHalfCpltCallback : Tx Half Complete Callback.
@@ -146,13 +146,13 @@
(+) MspDeInitCallback : IRDA MspDeInit.
[..]
- By default, after the @ref HAL_IRDA_Init() and when the state is HAL_IRDA_STATE_RESET
+ By default, after the HAL_IRDA_Init() and when the state is HAL_IRDA_STATE_RESET
all callbacks are set to the corresponding weak (surcharged) functions:
- examples @ref HAL_IRDA_TxCpltCallback(), @ref HAL_IRDA_RxHalfCpltCallback().
+ examples HAL_IRDA_TxCpltCallback(), HAL_IRDA_RxHalfCpltCallback().
Exception done for MspInit and MspDeInit functions that are respectively
- reset to the legacy weak (surcharged) functions in the @ref HAL_IRDA_Init()
- and @ref HAL_IRDA_DeInit() only when these callbacks are null (not registered beforehand).
- If not, MspInit or MspDeInit are not null, the @ref HAL_IRDA_Init() and @ref HAL_IRDA_DeInit()
+ reset to the legacy weak (surcharged) functions in the HAL_IRDA_Init()
+ and HAL_IRDA_DeInit() only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the HAL_IRDA_Init() and HAL_IRDA_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand).
[..]
@@ -161,8 +161,8 @@
in HAL_IRDA_STATE_READY or HAL_IRDA_STATE_RESET state, thus registered (user)
MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_IRDA_RegisterCallback() before calling @ref HAL_IRDA_DeInit()
- or @ref HAL_IRDA_Init() function.
+ using HAL_IRDA_RegisterCallback() before calling HAL_IRDA_DeInit()
+ or HAL_IRDA_Init() function.
[..]
When The compilation define USE_HAL_IRDA_REGISTER_CALLBACKS is set to 0 or
@@ -2362,7 +2362,7 @@
uint32_t tmpreg;
IRDA_ClockSourceTypeDef clocksource;
HAL_StatusTypeDef ret = HAL_OK;
- const uint16_t IRDAPrescTable[12] = {1U, 2U, 4U, 6U, 8U, 10U, 12U, 16U, 32U, 64U, 128U, 256U};
+ static const uint16_t IRDAPrescTable[12] = {1U, 2U, 4U, 6U, 8U, 10U, 12U, 16U, 32U, 64U, 128U, 256U};
uint32_t pclk;
/* Check the communication parameters */
diff --git a/Src/stm32wlxx_hal_iwdg.c b/Src/stm32wlxx_hal_iwdg.c
index 67d19e5..d95f368 100644
--- a/Src/stm32wlxx_hal_iwdg.c
+++ b/Src/stm32wlxx_hal_iwdg.c
@@ -65,13 +65,13 @@
(++) Configure the IWDG prescaler and counter reload value. This reload
value will be loaded in the IWDG counter each time the watchdog is
reloaded, then the IWDG will start counting down from this value.
- (++) Wait for status flags to be reset.
(++) Depending on window parameter:
(+++) If Window Init parameter is same as Window register value,
nothing more is done but reload counter value in order to exit
function with exact time base.
(+++) Else modify Window register. This will automatically reload
watchdog counter.
+ (++) Wait for status flags to be reset.
(#) Then the application program must refresh the IWDG counter at regular
intervals during normal operation to prevent an MCU reset, using
@@ -121,11 +121,14 @@
/* Status register needs up to 5 LSI clock periods divided by the clock
prescaler to be updated. The number of LSI clock periods is upper-rounded to
6 for the timeout value calculation.
- The timeout value is also calculated using the highest prescaler (256) and
+ The timeout value is calculated using the highest prescaler (256) and
the LSI_VALUE constant. The value of this constant can be changed by the user
to take into account possible LSI clock period variations.
- The timeout value is multiplied by 1000 to be converted in milliseconds. */
-#define HAL_IWDG_DEFAULT_TIMEOUT ((6UL * 256UL * 1000UL) / LSI_VALUE)
+ The timeout value is multiplied by 1000 to be converted in milliseconds.
+ LSI startup time is also considered here by adding LSI_STARTUP_TIMEOUT
+ converted in milliseconds. */
+#define HAL_IWDG_DEFAULT_TIMEOUT (((6UL * 256UL * 1000UL) / LSI_VALUE) + ((LSI_STARTUP_TIME / 1000UL) + 1UL))
+#define IWDG_KERNEL_UPDATE_FLAGS (IWDG_SR_WVU | IWDG_SR_RVU | IWDG_SR_PVU)
/**
* @}
*/
@@ -196,11 +199,14 @@
tickstart = HAL_GetTick();
/* Wait for register to be updated */
- while (hiwdg->Instance->SR != 0x00u)
+ while ((hiwdg->Instance->SR & IWDG_KERNEL_UPDATE_FLAGS) != 0x00u)
{
if ((HAL_GetTick() - tickstart) > HAL_IWDG_DEFAULT_TIMEOUT)
{
- return HAL_TIMEOUT;
+ if ((hiwdg->Instance->SR & IWDG_KERNEL_UPDATE_FLAGS) != 0x00u)
+ {
+ return HAL_TIMEOUT;
+ }
}
}
@@ -223,6 +229,7 @@
return HAL_OK;
}
+
/**
* @}
*/
@@ -242,7 +249,6 @@
* @{
*/
-
/**
* @brief Refresh the IWDG.
* @param hiwdg pointer to a IWDG_HandleTypeDef structure that contains
@@ -258,6 +264,7 @@
return HAL_OK;
}
+
/**
* @}
*/
diff --git a/Src/stm32wlxx_hal_lptim.c b/Src/stm32wlxx_hal_lptim.c
index db28046..9b849c8 100644
--- a/Src/stm32wlxx_hal_lptim.c
+++ b/Src/stm32wlxx_hal_lptim.c
@@ -96,13 +96,13 @@
The compilation define USE_HAL_LPTIM_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_LPTIM_RegisterCallback() to register a callback.
- @ref HAL_LPTIM_RegisterCallback() takes as parameters the HAL peripheral handle,
+ Use Function HAL_LPTIM_RegisterCallback() to register a callback.
+ HAL_LPTIM_RegisterCallback() takes as parameters the HAL peripheral handle,
the Callback ID and a pointer to the user callback function.
[..]
- Use function @ref HAL_LPTIM_UnRegisterCallback() to reset a callback to the
+ Use function HAL_LPTIM_UnRegisterCallback() to reset a callback to the
default weak function.
- @ref HAL_LPTIM_UnRegisterCallback takes as parameters the HAL peripheral handle,
+ HAL_LPTIM_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
[..]
These functions allow to register/unregister following callbacks:
@@ -122,7 +122,7 @@
[..]
By default, after the Init and when the state is HAL_LPTIM_STATE_RESET
all interrupt callbacks are set to the corresponding weak functions:
- examples @ref HAL_LPTIM_TriggerCallback(), @ref HAL_LPTIM_CompareMatchCallback().
+ examples HAL_LPTIM_TriggerCallback(), HAL_LPTIM_CompareMatchCallback().
[..]
Exception done for MspInit and MspDeInit functions that are reset to the legacy weak
@@ -136,7 +136,7 @@
in HAL_LPTIM_STATE_READY or HAL_LPTIM_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_LPTIM_RegisterCallback() before calling DeInit or Init function.
+ using HAL_LPTIM_RegisterCallback() before calling DeInit or Init function.
[..]
When The compilation define USE_HAL_LPTIM_REGISTER_CALLBACKS is set to 0 or
@@ -251,19 +251,17 @@
assert_param(IS_LPTIM_CLOCK_SOURCE(hlptim->Init.Clock.Source));
assert_param(IS_LPTIM_CLOCK_PRESCALER(hlptim->Init.Clock.Prescaler));
- if (hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM)
+ if ((hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM)
+ || (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL))
{
assert_param(IS_LPTIM_CLOCK_POLARITY(hlptim->Init.UltraLowPowerClock.Polarity));
+ assert_param(IS_LPTIM_CLOCK_SAMPLE_TIME(hlptim->Init.UltraLowPowerClock.SampleTime));
}
assert_param(IS_LPTIM_TRG_SOURCE(hlptim->Init.Trigger.Source));
if (hlptim->Init.Trigger.Source != LPTIM_TRIGSOURCE_SOFTWARE)
{
assert_param(IS_LPTIM_EXT_TRG_POLARITY(hlptim->Init.Trigger.ActiveEdge));
- }
- if (hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_APBCLOCK_LPOSC)
- {
assert_param(IS_LPTIM_TRIG_SAMPLE_TIME(hlptim->Init.Trigger.SampleTime));
- assert_param(IS_LPTIM_CLOCK_SAMPLE_TIME(hlptim->Init.UltraLowPowerClock.SampleTime));
}
assert_param(IS_LPTIM_OUTPUT_POLARITY(hlptim->Init.OutputPolarity));
assert_param(IS_LPTIM_UPDATE_MODE(hlptim->Init.UpdateMode));
@@ -322,21 +320,18 @@
/* Get the LPTIMx CFGR value */
tmpcfgr = hlptim->Instance->CFGR;
- if (hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM)
+ if ((hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM)
+ || (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL))
{
- tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKPOL));
+ tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKPOL | LPTIM_CFGR_CKFLT));
}
if (hlptim->Init.Trigger.Source != LPTIM_TRIGSOURCE_SOFTWARE)
{
- tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_TRIGSEL));
- }
- if (hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_APBCLOCK_LPOSC)
- {
- tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_TRGFLT | LPTIM_CFGR_CKFLT));
+ tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_TRGFLT | LPTIM_CFGR_TRIGSEL));
}
- /* Clear CKSEL, CKPOL, PRESC, TRIGEN, TRGFLT, WAVPOL, PRELOAD & COUNTMODE bits */
- tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKSEL | LPTIM_CFGR_CKPOL | LPTIM_CFGR_TRIGEN | LPTIM_CFGR_PRELOAD |
+ /* Clear CKSEL, PRESC, TRIGEN, TRGFLT, WAVPOL, PRELOAD & COUNTMODE bits */
+ tmpcfgr &= (uint32_t)(~(LPTIM_CFGR_CKSEL | LPTIM_CFGR_TRIGEN | LPTIM_CFGR_PRELOAD |
LPTIM_CFGR_WAVPOL | LPTIM_CFGR_PRESC | LPTIM_CFGR_COUNTMODE));
/* Set initialization parameters */
@@ -355,19 +350,21 @@
hlptim->Init.UltraLowPowerClock.SampleTime);
}
- /* Configure the active edge or edges used by the counter only if LPTIM is
- * clocked by an external clock source
- */
- if (hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM)
+ /* Configure LPTIM external clock polarity and digital filter */
+ if ((hlptim->Init.Clock.Source == LPTIM_CLOCKSOURCE_ULPTIM)
+ || (hlptim->Init.CounterSource == LPTIM_COUNTERSOURCE_EXTERNAL))
{
- tmpcfgr |= (hlptim->Init.UltraLowPowerClock.Polarity);
+ tmpcfgr |= (hlptim->Init.UltraLowPowerClock.Polarity |
+ hlptim->Init.UltraLowPowerClock.SampleTime);
}
+ /* Configure LPTIM external trigger */
if (hlptim->Init.Trigger.Source != LPTIM_TRIGSOURCE_SOFTWARE)
{
/* Enable External trigger and set the trigger source */
- tmpcfgr |= (hlptim->Init.Trigger.Source |
- hlptim->Init.Trigger.ActiveEdge);
+ tmpcfgr |= (hlptim->Init.Trigger.Source |
+ hlptim->Init.Trigger.ActiveEdge |
+ hlptim->Init.Trigger.SampleTime);
}
/* Write to LPTIMx CFGR */
diff --git a/Src/stm32wlxx_hal_pka.c b/Src/stm32wlxx_hal_pka.c
index 7faf33b..edc23a1 100644
--- a/Src/stm32wlxx_hal_pka.c
+++ b/Src/stm32wlxx_hal_pka.c
@@ -174,11 +174,11 @@
The compilation flag USE_HAL_PKA_REGISTER_CALLBACKS, when set to 1,
allows the user to configure dynamically the driver callbacks.
- Use Functions @ref HAL_PKA_RegisterCallback()
+ Use Functions HAL_PKA_RegisterCallback()
to register an interrupt callback.
[..]
- Function @ref HAL_PKA_RegisterCallback() allows to register following callbacks:
+ Function HAL_PKA_RegisterCallback() allows to register following callbacks:
(+) OperationCpltCallback : callback for End of operation.
(+) ErrorCallback : callback for error detection.
(+) MspInitCallback : callback for Msp Init.
@@ -187,11 +187,11 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_PKA_UnRegisterCallback to reset a callback to the default
+ Use function HAL_PKA_UnRegisterCallback to reset a callback to the default
weak function.
[..]
- @ref HAL_PKA_UnRegisterCallback takes as parameters the HAL peripheral handle,
+ HAL_PKA_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) OperationCpltCallback : callback for End of operation.
@@ -200,27 +200,27 @@
(+) MspDeInitCallback : callback for Msp DeInit.
[..]
- By default, after the @ref HAL_PKA_Init() and when the state is @ref HAL_PKA_STATE_RESET
+ By default, after the HAL_PKA_Init() and when the state is HAL_PKA_STATE_RESET
all callbacks are set to the corresponding weak functions:
- examples @ref HAL_PKA_OperationCpltCallback(), @ref HAL_PKA_ErrorCallback().
+ examples HAL_PKA_OperationCpltCallback(), HAL_PKA_ErrorCallback().
Exception done for MspInit and MspDeInit functions that are
- reset to the legacy weak functions in the @ref HAL_PKA_Init()/ @ref HAL_PKA_DeInit() only when
+ reset to the legacy weak functions in the HAL_PKA_Init()/ HAL_PKA_DeInit() only when
these callbacks are null (not registered beforehand).
[..]
- If MspInit or MspDeInit are not null, the @ref HAL_PKA_Init()/ @ref HAL_PKA_DeInit()
+ If MspInit or MspDeInit are not null, the HAL_PKA_Init()/ HAL_PKA_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
[..]
- Callbacks can be registered/unregistered in @ref HAL_PKA_STATE_READY state only.
+ Callbacks can be registered/unregistered in HAL_PKA_STATE_READY state only.
Exception done MspInit/MspDeInit functions that can be registered/unregistered
- in @ref HAL_PKA_STATE_READY or @ref HAL_PKA_STATE_RESET state,
+ in HAL_PKA_STATE_READY or HAL_PKA_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
[..]
Then, the user first registers the MspInit/MspDeInit user callbacks
- using @ref HAL_PKA_RegisterCallback() before calling @ref HAL_PKA_DeInit()
- or @ref HAL_PKA_Init() function.
+ using HAL_PKA_RegisterCallback() before calling HAL_PKA_DeInit()
+ or HAL_PKA_Init() function.
[..]
When the compilation flag USE_HAL_PKA_REGISTER_CALLBACKS is set to 0 or
diff --git a/Src/stm32wlxx_hal_pwr_ex.c b/Src/stm32wlxx_hal_pwr_ex.c
index 5c86117..34613a5 100644
--- a/Src/stm32wlxx_hal_pwr_ex.c
+++ b/Src/stm32wlxx_hal_pwr_ex.c
@@ -198,7 +198,7 @@
void HAL_PWREx_DisableInternalWakeUpLine(void)
{
#ifdef CORE_CM0PLUS
- CLEAR_BIT(PWR->CR3, PWR_C2CR3_EIWUL);
+ CLEAR_BIT(PWR->C2CR3, PWR_C2CR3_EIWUL);
#else
CLEAR_BIT(PWR->CR3, PWR_CR3_EIWUL);
#endif
diff --git a/Src/stm32wlxx_hal_rcc.c b/Src/stm32wlxx_hal_rcc.c
index d905622..27b9281 100644
--- a/Src/stm32wlxx_hal_rcc.c
+++ b/Src/stm32wlxx_hal_rcc.c
@@ -133,7 +133,7 @@
(+) MSI (Multiple Speed Internal): Its frequency is software trimmable from 100KHZ to 48MHZ.
The number of flash wait states is automatically adjusted when MSI range is updated with
- @ref HAL_RCC_OscConfig() and the MSI is used as System clock source.
+ HAL_RCC_OscConfig() and the MSI is used as System clock source.
(+) LSI (low-speed internal): 32 KHz low consumption RC used as IWDG and/or RTC
clock source.
@@ -173,14 +173,14 @@
on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived
from AHB clock through configurable prescalers and used to clock
the peripherals mapped on these buses. You can use
- "@ref HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks.
+ "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks.
The AHB3 clock (HCLK3) is derived from System clock through configurable
prescaler and used to clock the FLASH. APB3 (PCLK3) is derived from AHB3 clock.
-@- All the peripheral clocks are derived from the System clock (SYSCLK) except:
(+@) RTC: the RTC clock can be derived either from the LSI, LSE or HSE clock divided by 32.
- You have to use @ref __HAL_RCC_RTC_ENABLE() and @ref HAL_RCCEx_PeriphCLKConfig() function
+ You have to use __HAL_RCC_RTC_ENABLE() and HAL_RCCEx_PeriphCLKConfig() function
to configure this clock.
(+@) IWDG clock which is always the LSI clock.
@@ -1592,6 +1592,25 @@
}
/**
+ * @brief Get and clear reset flags
+ * @note Once reset flags are retrieved, this API is clearing them in order
+ * to isolate next reset reason.
+ * @retval can be a combination of @ref RCC_Reset_Flag
+ */
+uint32_t HAL_RCC_GetResetSource(void)
+{
+ uint32_t reset;
+
+ /* Get all reset flags */
+ reset = RCC->CSR & RCC_RESET_FLAG_ALL;
+
+ /* Clear Reset flags */
+ RCC->CSR |= RCC_CSR_RMVF;
+
+ return reset;
+}
+
+/**
* @}
*/
diff --git a/Src/stm32wlxx_hal_rcc_ex.c b/Src/stm32wlxx_hal_rcc_ex.c
index 89cad9d..4a71925 100644
--- a/Src/stm32wlxx_hal_rcc_ex.c
+++ b/Src/stm32wlxx_hal_rcc_ex.c
@@ -78,7 +78,7 @@
This subsection provides a set of functions allowing to control the RCC Clocks
frequencies.
[..]
- (@) Important note: Care must be taken when @ref HAL_RCCEx_PeriphCLKConfig() is used to
+ (@) Important note: Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to
select the RTC clock source; in this case the Backup domain will be reset in
order to modify the RTC Clock source, as consequence RTC registers (including
the backup registers) and RCC_BDCR register are set to their reset values.
diff --git a/Src/stm32wlxx_hal_rng.c b/Src/stm32wlxx_hal_rng.c
index 457f608..60dd1b7 100644
--- a/Src/stm32wlxx_hal_rng.c
+++ b/Src/stm32wlxx_hal_rng.c
@@ -31,8 +31,8 @@
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_RNG_RegisterCallback() to register a user callback.
- Function @ref HAL_RNG_RegisterCallback() allows to register following callbacks:
+ Use FunctionHAL_RNG_RegisterCallback() to register a user callback.
+ Function HAL_RNG_RegisterCallback() allows to register following callbacks:
(+) ErrorCallback : RNG Error Callback.
(+) MspInitCallback : RNG MspInit.
(+) MspDeInitCallback : RNG MspDeInit.
@@ -40,9 +40,9 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_RNG_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_RNG_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function.
- @ref HAL_RNG_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ HAL_RNG_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) ErrorCallback : RNG Error Callback.
@@ -51,16 +51,16 @@
[..]
For specific callback ReadyDataCallback, use dedicated register callbacks:
- respectively @ref HAL_RNG_RegisterReadyDataCallback() , @ref HAL_RNG_UnRegisterReadyDataCallback().
+ respectively HAL_RNG_RegisterReadyDataCallback() , HAL_RNG_UnRegisterReadyDataCallback().
[..]
- By default, after the @ref HAL_RNG_Init() and when the state is HAL_RNG_STATE_RESET
+ By default, after the HAL_RNG_Init() and when the state is HAL_RNG_STATE_RESET
all callbacks are set to the corresponding weak (surcharged) functions:
- example @ref HAL_RNG_ErrorCallback().
+ example HAL_RNG_ErrorCallback().
Exception done for MspInit and MspDeInit functions that are respectively
- reset to the legacy weak (surcharged) functions in the @ref HAL_RNG_Init()
- and @ref HAL_RNG_DeInit() only when these callbacks are null (not registered beforehand).
- If not, MspInit or MspDeInit are not null, the @ref HAL_RNG_Init() and @ref HAL_RNG_DeInit()
+ reset to the legacy weak (surcharged) functions in the HAL_RNG_Init()
+ and HAL_RNG_DeInit() only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the HAL_RNG_Init() and HAL_RNG_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand).
[..]
@@ -69,8 +69,8 @@
in HAL_RNG_STATE_READY or HAL_RNG_STATE_RESET state, thus registered (user)
MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_RNG_RegisterCallback() before calling @ref HAL_RNG_DeInit()
- or @ref HAL_RNG_Init() function.
+ using HAL_RNG_RegisterCallback() before calling HAL_RNG_DeInit()
+ or HAL_RNG_Init() function.
[..]
When The compilation define USE_HAL_RNG_REGISTER_CALLBACKS is set to 0 or
@@ -227,9 +227,13 @@
{
if ((HAL_GetTick() - tickstart) > RNG_TIMEOUT_VALUE)
{
- hrng->State = HAL_RNG_STATE_READY;
- hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
- return HAL_ERROR;
+ /* New check to avoid false timeout detection in case of preemption */
+ if (HAL_IS_BIT_SET(hrng->Instance->CR, RNG_CR_CONDRST))
+ {
+ hrng->State = HAL_RNG_STATE_READY;
+ hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
+ return HAL_ERROR;
+ }
}
}
@@ -249,9 +253,13 @@
{
if ((HAL_GetTick() - tickstart) > RNG_TIMEOUT_VALUE)
{
- hrng->State = HAL_RNG_STATE_ERROR;
- hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
- return HAL_ERROR;
+ /* New check to avoid false timeout detection in case of preemption */
+ if (__HAL_RNG_GET_FLAG(hrng, RNG_FLAG_SECS) != RESET)
+ {
+ hrng->State = HAL_RNG_STATE_ERROR;
+ hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
+ return HAL_ERROR;
+ }
}
}
@@ -295,11 +303,15 @@
{
if ((HAL_GetTick() - tickstart) > RNG_TIMEOUT_VALUE)
{
- hrng->State = HAL_RNG_STATE_READY;
- hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
- /* Process Unlocked */
- __HAL_UNLOCK(hrng);
- return HAL_ERROR;
+ /* New check to avoid false timeout detection in case of preemption */
+ if (HAL_IS_BIT_SET(hrng->Instance->CR, RNG_CR_CONDRST))
+ {
+ hrng->State = HAL_RNG_STATE_READY;
+ hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrng);
+ return HAL_ERROR;
+ }
}
}
@@ -665,11 +677,15 @@
{
if ((HAL_GetTick() - tickstart) > RNG_TIMEOUT_VALUE)
{
- hrng->State = HAL_RNG_STATE_READY;
- hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
- /* Process Unlocked */
- __HAL_UNLOCK(hrng);
- return HAL_ERROR;
+ /* New check to avoid false timeout detection in case of preemption */
+ if (__HAL_RNG_GET_FLAG(hrng, RNG_FLAG_DRDY) == RESET)
+ {
+ hrng->State = HAL_RNG_STATE_READY;
+ hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrng);
+ return HAL_ERROR;
+ }
}
}
diff --git a/Src/stm32wlxx_hal_rng_ex.c b/Src/stm32wlxx_hal_rng_ex.c
index 09fd3f7..34591bc 100644
--- a/Src/stm32wlxx_hal_rng_ex.c
+++ b/Src/stm32wlxx_hal_rng_ex.c
@@ -31,7 +31,7 @@
#if defined(RNG)
-/** @addtogroup RNGEx
+/** @addtogroup RNG_Ex
* @brief RNG Extended HAL module driver.
* @{
*/
@@ -40,7 +40,7 @@
#if defined(RNG_CR_CONDRST)
/* Private types -------------------------------------------------------------*/
/* Private defines -----------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Defines RNGEx Private Defines
+/** @defgroup RNG_Ex_Private_Defines RNGEx Private Defines
* @{
*/
/* Health test control register information to use in CCM algorithm */
@@ -51,7 +51,7 @@
*/
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
-/** @defgroup RNGEx_Private_Constants RNGEx Private Constants
+/** @defgroup RNG_Ex_Private_Constants RNGEx Private Constants
* @{
*/
#define RNG_TIMEOUT_VALUE 2U
@@ -63,11 +63,11 @@
/* Private functions --------------------------------------------------------*/
/* Exported functions --------------------------------------------------------*/
-/** @addtogroup RNGEx_Exported_Functions
+/** @addtogroup RNG_Ex_Exported_Functions
* @{
*/
-/** @addtogroup RNGEx_Exported_Functions_Group1
+/** @addtogroup RNG_Ex_Exported_Functions_Group1
* @brief Configuration functions
*
@verbatim
@@ -152,9 +152,13 @@
{
if ((HAL_GetTick() - tickstart) > RNG_TIMEOUT_VALUE)
{
- hrng->State = HAL_RNG_STATE_READY;
- hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
- return HAL_ERROR;
+ /* New check to avoid false timeout detection in case of prememption */
+ if (HAL_IS_BIT_SET(hrng->Instance->CR, RNG_CR_CONDRST))
+ {
+ hrng->State = HAL_RNG_STATE_READY;
+ hrng->ErrorCode = HAL_RNG_ERROR_TIMEOUT;
+ return HAL_ERROR;
+ }
}
}
@@ -276,7 +280,7 @@
* @}
*/
-/** @addtogroup RNGEx_Exported_Functions_Group2
+/** @addtogroup RNG_Ex_Exported_Functions_Group2
* @brief Recover from seed error function
*
@verbatim
diff --git a/Src/stm32wlxx_hal_rtc.c b/Src/stm32wlxx_hal_rtc.c
index 93ac670..67c9788 100644
--- a/Src/stm32wlxx_hal_rtc.c
+++ b/Src/stm32wlxx_hal_rtc.c
@@ -1174,14 +1174,18 @@
assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
- if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ if( sAlarm->AlarmMask != RTC_ALARMMASK_DATEWEEKDAY )
{
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
+ }
}
- else
- {
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
- }
+
tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds) << RTC_ALRMAR_SU_Pos) | \
@@ -1192,30 +1196,37 @@
}
else /* format BCD */
{
- if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
+ if( sAlarm->AlarmMask != RTC_ALARMMASK_ALL )
{
- assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
- assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
- }
- else
- {
- sAlarm->AlarmTime.TimeFormat = 0x00U;
- assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
- }
+ if( sAlarm->AlarmMask != RTC_ALARMMASK_HOURS )
+ {
+ if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
+ {
+ assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00U;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ }
+ }
- assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
- assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
-
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+ }
#ifdef USE_FULL_ASSERT
- if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ if( ( sAlarm->AlarmMask != RTC_ALARMMASK_ALL ) && ( sAlarm->AlarmMask != RTC_ALARMMASK_DATEWEEKDAY ) )
{
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
}
- else
- {
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
- }
-
#endif /* USE_FULL_ASSERT */
tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
@@ -1369,14 +1380,18 @@
assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
- if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ if( sAlarm->AlarmMask != RTC_ALARMMASK_DATEWEEKDAY )
{
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
+ }
}
- else
- {
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
- }
+
tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds) << RTC_ALRMAR_SU_Pos) | \
@@ -1387,30 +1402,38 @@
}
else /* Format BCD */
{
- if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
+ if( sAlarm->AlarmMask != RTC_ALARMMASK_ALL )
{
- assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
- assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
- }
- else
- {
- sAlarm->AlarmTime.TimeFormat = 0x00U;
- assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
- }
+ if( sAlarm->AlarmMask != RTC_ALARMMASK_HOURS )
+ {
+ if (READ_BIT(RTC->CR, RTC_CR_FMT) != 0U)
+ {
+ assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00U;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ }
+ }
- assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
- assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+ }
#ifdef USE_FULL_ASSERT
- if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ if( ( sAlarm->AlarmMask != RTC_ALARMMASK_ALL ) && ( sAlarm->AlarmMask != RTC_ALARMMASK_DATEWEEKDAY ) )
{
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ if (sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
}
- else
- {
- assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
- }
-
#endif /* USE_FULL_ASSERT */
tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
((uint32_t)(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
@@ -1516,26 +1539,33 @@
if (Alarm == RTC_ALARM_A)
{
- /* AlarmA, Clear SSCLR */
- CLEAR_BIT(RTC->ALRMASSR, RTC_ALRMASSR_SSCLR);
-
/* AlarmA, In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, RTC_CR_ALRAE | RTC_CR_ALRAIE);
+ /* AlarmA, Clear SSCLR */
+ CLEAR_BIT(RTC->ALRMASSR, RTC_ALRMASSR_SSCLR);
+
/* Store in the handle the Alarm A disabled */
CLEAR_BIT(hrtc->IsEnabled.RtcFeatures, RTC_MISR_ALRAMF);
+
+ /* Clear AlarmA flag */
+ WRITE_REG(RTC->SCR, RTC_SCR_CALRAF);
}
else
{
- /* AlarmB, Clear SSCLR */
- CLEAR_BIT(RTC->ALRMBSSR, RTC_ALRMBSSR_SSCLR);
-
/* AlarmB, In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, RTC_CR_ALRBE | RTC_CR_ALRBIE);
+ /* AlarmB, Clear SSCLR */
+ CLEAR_BIT(RTC->ALRMBSSR, RTC_ALRMBSSR_SSCLR);
+
/* Store in the handle the Alarm B disabled */
CLEAR_BIT(hrtc->IsEnabled.RtcFeatures, RTC_MISR_ALRBMF);
+
+ /* Clear AlarmB flag */
+ WRITE_REG(RTC->SCR, RTC_SCR_CALRBF);
}
+
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
@@ -1742,7 +1772,7 @@
UNUSED(hrtc);
/* Clear RSF flag */
- SET_BIT(RTC->ICSR, RTC_RSF_MASK);
+ CLEAR_BIT(RTC->ICSR, RTC_ICSR_RSF);
tickstart = HAL_GetTick();
diff --git a/Src/stm32wlxx_hal_rtc_ex.c b/Src/stm32wlxx_hal_rtc_ex.c
index 815977e..f4c8526 100644
--- a/Src/stm32wlxx_hal_rtc_ex.c
+++ b/Src/stm32wlxx_hal_rtc_ex.c
@@ -282,6 +282,12 @@
/* In case of interrupt mode is used, the interrupt source must disabled */
CLEAR_BIT(RTC->CR, (RTC_CR_TSEDGE | RTC_CR_TSE | RTC_CR_TSIE));
+ /* Clear timestamp flag only if internal timestamp flag not set */
+ if( READ_BIT( RTC->SR, RTC_SR_ITSF) == 0U )
+ {
+ WRITE_REG(RTC->SCR, RTC_SCR_CTSF);
+ }
+
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
@@ -342,6 +348,16 @@
/* Configure the internal Time Stamp Enable bits */
CLEAR_BIT(RTC->CR, RTC_CR_ITSE);
+ /* Clear internal timestamp flag if Timestamp not enabled and TSOVF not set */
+ WRITE_REG(RTC->SCR, RTC_SCR_CITSF);
+ if ( READ_BIT(RTC->SR, RTC_SR_TSOVF) == 0U )
+ {
+ if ( READ_BIT(RTC->CR, RTC_CR_TSE) == 0U )
+ {
+ WRITE_REG(RTC->SCR, RTC_SCR_CTSF);
+ }
+ }
+
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
@@ -710,6 +726,9 @@
}
}
+ /* Clear wakeup timer flag */
+ WRITE_REG(RTC->SCR, RTC_SCR_CWUTF);
+
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
@@ -1355,6 +1374,9 @@
/* In case of interrupt mode is used, the interrupt source must disabled */
__HAL_RTC_SSRU_DISABLE_IT(hrtc, RTC_IT_TS);
+ /* Clear SSR underflow flag */
+ WRITE_REG(RTC->SCR, RTC_SCR_CSSRUF);
+
/* Enable the write protection for RTC registers */
__HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
diff --git a/Src/stm32wlxx_hal_smartcard.c b/Src/stm32wlxx_hal_smartcard.c
index f811a6b..67f585e 100644
--- a/Src/stm32wlxx_hal_smartcard.c
+++ b/Src/stm32wlxx_hal_smartcard.c
@@ -107,8 +107,8 @@
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_SMARTCARD_RegisterCallback() to register a user callback.
- Function @ref HAL_SMARTCARD_RegisterCallback() allows to register following callbacks:
+ Use Function HAL_SMARTCARD_RegisterCallback() to register a user callback.
+ Function HAL_SMARTCARD_RegisterCallback() allows to register following callbacks:
(+) TxCpltCallback : Tx Complete Callback.
(+) RxCpltCallback : Rx Complete Callback.
(+) ErrorCallback : Error Callback.
@@ -123,9 +123,9 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_SMARTCARD_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_SMARTCARD_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function.
- @ref HAL_SMARTCARD_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ HAL_SMARTCARD_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) TxCpltCallback : Tx Complete Callback.
@@ -140,13 +140,13 @@
(+) MspDeInitCallback : SMARTCARD MspDeInit.
[..]
- By default, after the @ref HAL_SMARTCARD_Init() and when the state is HAL_SMARTCARD_STATE_RESET
+ By default, after the HAL_SMARTCARD_Init() and when the state is HAL_SMARTCARD_STATE_RESET
all callbacks are set to the corresponding weak (surcharged) functions:
- examples @ref HAL_SMARTCARD_TxCpltCallback(), @ref HAL_SMARTCARD_RxCpltCallback().
+ examples HAL_SMARTCARD_TxCpltCallback(), HAL_SMARTCARD_RxCpltCallback().
Exception done for MspInit and MspDeInit functions that are respectively
- reset to the legacy weak (surcharged) functions in the @ref HAL_SMARTCARD_Init()
- and @ref HAL_SMARTCARD_DeInit() only when these callbacks are null (not registered beforehand).
- If not, MspInit or MspDeInit are not null, the @ref HAL_SMARTCARD_Init() and @ref HAL_SMARTCARD_DeInit()
+ reset to the legacy weak (surcharged) functions in the HAL_SMARTCARD_Init()
+ and HAL_SMARTCARD_DeInit() only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the HAL_SMARTCARD_Init() and HAL_SMARTCARD_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand).
[..]
@@ -155,8 +155,8 @@
in HAL_SMARTCARD_STATE_READY or HAL_SMARTCARD_STATE_RESET state, thus registered (user)
MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_SMARTCARD_RegisterCallback() before calling @ref HAL_SMARTCARD_DeInit()
- or @ref HAL_SMARTCARD_Init() function.
+ using HAL_SMARTCARD_RegisterCallback() before calling HAL_SMARTCARD_DeInit()
+ or HAL_SMARTCARD_Init() function.
[..]
When The compilation define USE_HAL_SMARTCARD_REGISTER_CALLBACKS is set to 0 or
@@ -2327,7 +2327,7 @@
uint32_t tmpreg;
SMARTCARD_ClockSourceTypeDef clocksource;
HAL_StatusTypeDef ret = HAL_OK;
- const uint16_t SMARTCARDPrescTable[12] = {1U, 2U, 4U, 6U, 8U, 10U, 12U, 16U, 32U, 64U, 128U, 256U};
+ static const uint16_t SMARTCARDPrescTable[12] = {1U, 2U, 4U, 6U, 8U, 10U, 12U, 16U, 32U, 64U, 128U, 256U};
uint32_t pclk;
/* Check the parameters */
diff --git a/Src/stm32wlxx_hal_smartcard_ex.c b/Src/stm32wlxx_hal_smartcard_ex.c
index 823dc41..6a27ed4 100644
--- a/Src/stm32wlxx_hal_smartcard_ex.c
+++ b/Src/stm32wlxx_hal_smartcard_ex.c
@@ -458,8 +458,8 @@
uint8_t rx_fifo_threshold;
uint8_t tx_fifo_threshold;
/* 2 0U/1U added for MISRAC2012-Rule-18.1_b and MISRAC2012-Rule-18.1_d */
- uint8_t numerator[] = {1U, 1U, 1U, 3U, 7U, 1U, 0U, 0U};
- uint8_t denominator[] = {8U, 4U, 2U, 4U, 8U, 1U, 1U, 1U};
+ static const uint8_t numerator[] = {1U, 1U, 1U, 3U, 7U, 1U, 0U, 0U};
+ static const uint8_t denominator[] = {8U, 4U, 2U, 4U, 8U, 1U, 1U, 1U};
if (hsmartcard->FifoMode == SMARTCARD_FIFOMODE_DISABLE)
{
diff --git a/Src/stm32wlxx_hal_smbus.c b/Src/stm32wlxx_hal_smbus.c
index 5754a50..6321032 100644
--- a/Src/stm32wlxx_hal_smbus.c
+++ b/Src/stm32wlxx_hal_smbus.c
@@ -20,7 +20,7 @@
(#) Declare a SMBUS_HandleTypeDef handle structure, for example:
SMBUS_HandleTypeDef hsmbus;
- (#)Initialize the SMBUS low level resources by implementing the @ref HAL_SMBUS_MspInit() API:
+ (#)Initialize the SMBUS low level resources by implementing the HAL_SMBUS_MspInit() API:
(##) Enable the SMBUSx interface clock
(##) SMBUS pins configuration
(+++) Enable the clock for the SMBUS GPIOs
@@ -33,69 +33,75 @@
Dual Addressing mode, Own Address2, Own Address2 Mask, General call, Nostretch mode,
Peripheral mode and Packet Error Check mode in the hsmbus Init structure.
- (#) Initialize the SMBUS registers by calling the @ref HAL_SMBUS_Init() API:
+ (#) Initialize the SMBUS registers by calling the HAL_SMBUS_Init() API:
(++) These API's configures also the low level Hardware GPIO, CLOCK, CORTEX...etc)
- by calling the customized @ref HAL_SMBUS_MspInit(&hsmbus) API.
+ by calling the customized HAL_SMBUS_MspInit(&hsmbus) API.
- (#) To check if target device is ready for communication, use the function @ref HAL_SMBUS_IsDeviceReady()
+ (#) To check if target device is ready for communication, use the function HAL_SMBUS_IsDeviceReady()
(#) For SMBUS IO operations, only one mode of operations is available within this driver
*** Interrupt mode IO operation ***
===================================
[..]
- (+) Transmit in master/host SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Master_Transmit_IT()
- (++) At transmission end of transfer @ref HAL_SMBUS_MasterTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_MasterTxCpltCallback()
- (+) Receive in master/host SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Master_Receive_IT()
- (++) At reception end of transfer @ref HAL_SMBUS_MasterRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_MasterRxCpltCallback()
- (+) Abort a master/host SMBUS process communication with Interrupt using @ref HAL_SMBUS_Master_Abort_IT()
+ (+) Transmit in master/host SMBUS mode an amount of data in non-blocking mode
+ using HAL_SMBUS_Master_Transmit_IT()
+ (++) At transmission end of transfer HAL_SMBUS_MasterTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_MasterTxCpltCallback()
+ (+) Receive in master/host SMBUS mode an amount of data in non-blocking mode
+ using HAL_SMBUS_Master_Receive_IT()
+ (++) At reception end of transfer HAL_SMBUS_MasterRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_MasterRxCpltCallback()
+ (+) Abort a master/host SMBUS process communication with Interrupt using HAL_SMBUS_Master_Abort_IT()
(++) The associated previous transfer callback is called at the end of abort process
- (++) mean @ref HAL_SMBUS_MasterTxCpltCallback() in case of previous state was master transmit
- (++) mean @ref HAL_SMBUS_MasterRxCpltCallback() in case of previous state was master receive
+ (++) mean HAL_SMBUS_MasterTxCpltCallback() in case of previous state was master transmit
+ (++) mean HAL_SMBUS_MasterRxCpltCallback() in case of previous state was master receive
(+) Enable/disable the Address listen mode in slave/device or host/slave SMBUS mode
- using @ref HAL_SMBUS_EnableListen_IT() @ref HAL_SMBUS_DisableListen_IT()
- (++) When address slave/device SMBUS match, @ref HAL_SMBUS_AddrCallback() is executed and user can
- add his own code to check the Address Match Code and the transmission direction request by master/host (Write/Read).
- (++) At Listen mode end @ref HAL_SMBUS_ListenCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_ListenCpltCallback()
- (+) Transmit in slave/device SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Slave_Transmit_IT()
- (++) At transmission end of transfer @ref HAL_SMBUS_SlaveTxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_SlaveTxCpltCallback()
- (+) Receive in slave/device SMBUS mode an amount of data in non-blocking mode using @ref HAL_SMBUS_Slave_Receive_IT()
- (++) At reception end of transfer @ref HAL_SMBUS_SlaveRxCpltCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_SlaveRxCpltCallback()
- (+) Enable/Disable the SMBUS alert mode using @ref HAL_SMBUS_EnableAlert_IT() @ref HAL_SMBUS_DisableAlert_IT()
- (++) When SMBUS Alert is generated @ref HAL_SMBUS_ErrorCallback() is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_ErrorCallback()
- to check the Alert Error Code using function @ref HAL_SMBUS_GetError()
- (+) Get HAL state machine or error values using @ref HAL_SMBUS_GetState() or @ref HAL_SMBUS_GetError()
- (+) In case of transfer Error, @ref HAL_SMBUS_ErrorCallback() function is executed and user can
- add his own code by customization of function pointer @ref HAL_SMBUS_ErrorCallback()
- to check the Error Code using function @ref HAL_SMBUS_GetError()
+ using HAL_SMBUS_EnableListen_IT() HAL_SMBUS_DisableListen_IT()
+ (++) When address slave/device SMBUS match, HAL_SMBUS_AddrCallback() is executed and users can
+ add their own code to check the Address Match Code and the transmission direction
+ request by master/host (Write/Read).
+ (++) At Listen mode end HAL_SMBUS_ListenCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_ListenCpltCallback()
+ (+) Transmit in slave/device SMBUS mode an amount of data in non-blocking mode
+ using HAL_SMBUS_Slave_Transmit_IT()
+ (++) At transmission end of transfer HAL_SMBUS_SlaveTxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_SlaveTxCpltCallback()
+ (+) Receive in slave/device SMBUS mode an amount of data in non-blocking mode
+ using HAL_SMBUS_Slave_Receive_IT()
+ (++) At reception end of transfer HAL_SMBUS_SlaveRxCpltCallback() is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_SlaveRxCpltCallback()
+ (+) Enable/Disable the SMBUS alert mode using
+ HAL_SMBUS_EnableAlert_IT() or HAL_SMBUS_DisableAlert_IT()
+ (++) When SMBUS Alert is generated HAL_SMBUS_ErrorCallback() is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_ErrorCallback()
+ to check the Alert Error Code using function HAL_SMBUS_GetError()
+ (+) Get HAL state machine or error values using HAL_SMBUS_GetState() or HAL_SMBUS_GetError()
+ (+) In case of transfer Error, HAL_SMBUS_ErrorCallback() function is executed and users can
+ add their own code by customization of function pointer HAL_SMBUS_ErrorCallback()
+ to check the Error Code using function HAL_SMBUS_GetError()
*** SMBUS HAL driver macros list ***
==================================
[..]
Below the list of most used macros in SMBUS HAL driver.
- (+) @ref __HAL_SMBUS_ENABLE: Enable the SMBUS peripheral
- (+) @ref __HAL_SMBUS_DISABLE: Disable the SMBUS peripheral
- (+) @ref __HAL_SMBUS_GET_FLAG: Check whether the specified SMBUS flag is set or not
- (+) @ref __HAL_SMBUS_CLEAR_FLAG: Clear the specified SMBUS pending flag
- (+) @ref __HAL_SMBUS_ENABLE_IT: Enable the specified SMBUS interrupt
- (+) @ref __HAL_SMBUS_DISABLE_IT: Disable the specified SMBUS interrupt
+ (+) __HAL_SMBUS_ENABLE: Enable the SMBUS peripheral
+ (+) __HAL_SMBUS_DISABLE: Disable the SMBUS peripheral
+ (+) __HAL_SMBUS_GET_FLAG: Check whether the specified SMBUS flag is set or not
+ (+) __HAL_SMBUS_CLEAR_FLAG: Clear the specified SMBUS pending flag
+ (+) __HAL_SMBUS_ENABLE_IT: Enable the specified SMBUS interrupt
+ (+) __HAL_SMBUS_DISABLE_IT: Disable the specified SMBUS interrupt
*** Callback registration ***
=============================================
[..]
The compilation flag USE_HAL_SMBUS_REGISTER_CALLBACKS when set to 1
allows the user to configure dynamically the driver callbacks.
- Use Functions @ref HAL_SMBUS_RegisterCallback() or @ref HAL_SMBUS_RegisterAddrCallback()
+ Use Functions HAL_SMBUS_RegisterCallback() or HAL_SMBUS_RegisterAddrCallback()
to register an interrupt callback.
[..]
- Function @ref HAL_SMBUS_RegisterCallback() allows to register following callbacks:
+ Function HAL_SMBUS_RegisterCallback() allows to register following callbacks:
(+) MasterTxCpltCallback : callback for Master transmission end of transfer.
(+) MasterRxCpltCallback : callback for Master reception end of transfer.
(+) SlaveTxCpltCallback : callback for Slave transmission end of transfer.
@@ -107,11 +113,11 @@
This function takes as parameters the HAL peripheral handle, the Callback ID
and a pointer to the user callback function.
[..]
- For specific callback AddrCallback use dedicated register callbacks : @ref HAL_SMBUS_RegisterAddrCallback.
+ For specific callback AddrCallback use dedicated register callbacks : HAL_SMBUS_RegisterAddrCallback.
[..]
- Use function @ref HAL_SMBUS_UnRegisterCallback to reset a callback to the default
+ Use function HAL_SMBUS_UnRegisterCallback to reset a callback to the default
weak function.
- @ref HAL_SMBUS_UnRegisterCallback takes as parameters the HAL peripheral handle,
+ HAL_SMBUS_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) MasterTxCpltCallback : callback for Master transmission end of transfer.
@@ -123,24 +129,24 @@
(+) MspInitCallback : callback for Msp Init.
(+) MspDeInitCallback : callback for Msp DeInit.
[..]
- For callback AddrCallback use dedicated register callbacks : @ref HAL_SMBUS_UnRegisterAddrCallback.
+ For callback AddrCallback use dedicated register callbacks : HAL_SMBUS_UnRegisterAddrCallback.
[..]
- By default, after the @ref HAL_SMBUS_Init() and when the state is @ref HAL_I2C_STATE_RESET
+ By default, after theHAL_SMBUS_Init() and when the state is HAL_I2C_STATE_RESET
all callbacks are set to the corresponding weak functions:
- examples @ref HAL_SMBUS_MasterTxCpltCallback(), @ref HAL_SMBUS_MasterRxCpltCallback().
+ examples HAL_SMBUS_MasterTxCpltCallback(), HAL_SMBUS_MasterRxCpltCallback().
Exception done for MspInit and MspDeInit functions that are
- reset to the legacy weak functions in the @ref HAL_SMBUS_Init()/ @ref HAL_SMBUS_DeInit() only when
+ reset to the legacy weak functions in the HAL_SMBUS_Init()/ HAL_SMBUS_DeInit() only when
these callbacks are null (not registered beforehand).
- If MspInit or MspDeInit are not null, the @ref HAL_SMBUS_Init()/ @ref HAL_SMBUS_DeInit()
+ If MspInit or MspDeInit are not null, the HAL_SMBUS_Init()/ HAL_SMBUS_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand) whatever the state.
[..]
- Callbacks can be registered/unregistered in @ref HAL_I2C_STATE_READY state only.
+ Callbacks can be registered/unregistered in HAL_I2C_STATE_READY state only.
Exception done MspInit/MspDeInit functions that can be registered/unregistered
- in @ref HAL_I2C_STATE_READY or @ref HAL_I2C_STATE_RESET state,
+ in HAL_I2C_STATE_READY or HAL_I2C_STATE_RESET state,
thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
Then, the user first registers the MspInit/MspDeInit user callbacks
- using @ref HAL_SMBUS_RegisterCallback() before calling @ref HAL_SMBUS_DeInit()
- or @ref HAL_SMBUS_Init() function.
+ using HAL_SMBUS_RegisterCallback() before calling HAL_SMBUS_DeInit()
+ or HAL_SMBUS_Init() function.
[..]
When the compilation flag USE_HAL_SMBUS_REGISTER_CALLBACKS is set to 0 or
not defined, the callback registration feature is not available and all callbacks
@@ -203,8 +209,8 @@
/** @addtogroup SMBUS_Private_Functions SMBUS Private Functions
* @{
*/
-static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status,
- uint32_t Timeout);
+static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag,
+ FlagStatus Status, uint32_t Timeout);
static void SMBUS_Enable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint32_t InterruptRequest);
static void SMBUS_Disable_IRQ(SMBUS_HandleTypeDef *hsmbus, uint32_t InterruptRequest);
@@ -215,8 +221,8 @@
static void SMBUS_ITErrorHandler(SMBUS_HandleTypeDef *hsmbus);
-static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode,
- uint32_t Request);
+static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size,
+ uint32_t Mode, uint32_t Request);
/**
* @}
*/
@@ -364,15 +370,20 @@
/*---------------------------- SMBUSx OAR2 Configuration -----------------------*/
/* Configure SMBUSx: Dual mode and Own Address2 */
- hsmbus->Instance->OAR2 = (hsmbus->Init.DualAddressMode | hsmbus->Init.OwnAddress2 | (hsmbus->Init.OwnAddress2Masks << 8U));
+ hsmbus->Instance->OAR2 = (hsmbus->Init.DualAddressMode | hsmbus->Init.OwnAddress2 | \
+ (hsmbus->Init.OwnAddress2Masks << 8U));
/*---------------------------- SMBUSx CR1 Configuration ------------------------*/
/* Configure SMBUSx: Generalcall and NoStretch mode */
- hsmbus->Instance->CR1 = (hsmbus->Init.GeneralCallMode | hsmbus->Init.NoStretchMode | hsmbus->Init.PacketErrorCheckMode | hsmbus->Init.PeripheralMode | hsmbus->Init.AnalogFilter);
+ hsmbus->Instance->CR1 = (hsmbus->Init.GeneralCallMode | hsmbus->Init.NoStretchMode | \
+ hsmbus->Init.PacketErrorCheckMode | hsmbus->Init.PeripheralMode | \
+ hsmbus->Init.AnalogFilter);
- /* Enable Slave Byte Control only in case of Packet Error Check is enabled and SMBUS Peripheral is set in Slave mode */
- if ((hsmbus->Init.PacketErrorCheckMode == SMBUS_PEC_ENABLE)
- && ((hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE) || (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE_ARP)))
+ /* Enable Slave Byte Control only in case of Packet Error Check is enabled
+ and SMBUS Peripheral is set in Slave mode */
+ if ((hsmbus->Init.PacketErrorCheckMode == SMBUS_PEC_ENABLE) && \
+ ((hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE) || \
+ (hsmbus->Init.PeripheralMode == SMBUS_PERIPHERAL_MODE_SMBUS_SLAVE_ARP)))
{
hsmbus->Instance->CR1 |= I2C_CR1_SBC;
}
@@ -581,7 +592,8 @@
* @param pCallback pointer to the Callback function
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_SMBUS_RegisterCallback(SMBUS_HandleTypeDef *hsmbus, HAL_SMBUS_CallbackIDTypeDef CallbackID,
+HAL_StatusTypeDef HAL_SMBUS_RegisterCallback(SMBUS_HandleTypeDef *hsmbus,
+ HAL_SMBUS_CallbackIDTypeDef CallbackID,
pSMBUS_CallbackTypeDef pCallback)
{
HAL_StatusTypeDef status = HAL_OK;
@@ -695,7 +707,8 @@
* @arg @ref HAL_SMBUS_MSPDEINIT_CB_ID MspDeInit callback ID
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_SMBUS_UnRegisterCallback(SMBUS_HandleTypeDef *hsmbus, HAL_SMBUS_CallbackIDTypeDef CallbackID)
+HAL_StatusTypeDef HAL_SMBUS_UnRegisterCallback(SMBUS_HandleTypeDef *hsmbus,
+ HAL_SMBUS_CallbackIDTypeDef CallbackID)
{
HAL_StatusTypeDef status = HAL_OK;
@@ -790,7 +803,8 @@
* @param pCallback pointer to the Address Match Callback function
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_SMBUS_RegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus, pSMBUS_AddrCallbackTypeDef pCallback)
+HAL_StatusTypeDef HAL_SMBUS_RegisterAddrCallback(SMBUS_HandleTypeDef *hsmbus,
+ pSMBUS_AddrCallbackTypeDef pCallback)
{
HAL_StatusTypeDef status = HAL_OK;
@@ -914,8 +928,8 @@
* @param XferOptions Options of Transfer, value of @ref SMBUS_XferOptions_definition
* @retval HAL status
*/
-HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t *pData,
- uint16_t Size, uint32_t XferOptions)
+HAL_StatusTypeDef HAL_SMBUS_Master_Transmit_IT(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress,
+ uint8_t *pData, uint16_t Size, uint32_t XferOptions)
{
uint32_t tmp;
@@ -955,7 +969,8 @@
if ((hsmbus->XferSize < hsmbus->XferCount) && (hsmbus->XferSize == MAX_NBYTE_SIZE))
{
SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize,
- SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_WRITE);
+ SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE),
+ SMBUS_GENERATE_START_WRITE);
}
else
{
@@ -965,9 +980,11 @@
/* Store current volatile XferOptions, misra rule */
tmp = hsmbus->XferOptions;
- if ((hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX) && (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(tmp) == 0))
+ if ((hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_TX) && \
+ (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(tmp) == 0))
{
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions,
+ SMBUS_NO_STARTSTOP);
}
/* Else transfer direction change, so generate Restart with new transfer direction */
else
@@ -976,7 +993,9 @@
SMBUS_ConvertOtherXferOptions(hsmbus);
/* Handle Transfer */
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_WRITE);
+ SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize,
+ hsmbus->XferOptions,
+ SMBUS_GENERATE_START_WRITE);
}
/* If PEC mode is enable, size to transmit manage by SW part should be Size-1 byte, corresponding to PEC byte */
@@ -1057,7 +1076,8 @@
if ((hsmbus->XferSize < hsmbus->XferCount) && (hsmbus->XferSize == MAX_NBYTE_SIZE))
{
SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize,
- SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_GENERATE_START_READ);
+ SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE),
+ SMBUS_GENERATE_START_READ);
}
else
{
@@ -1067,9 +1087,11 @@
/* Store current volatile XferOptions, Misra rule */
tmp = hsmbus->XferOptions;
- if ((hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX) && (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(tmp) == 0))
+ if ((hsmbus->PreviousState == HAL_SMBUS_STATE_MASTER_BUSY_RX) && \
+ (IS_SMBUS_TRANSFER_OTHER_OPTIONS_REQUEST(tmp) == 0))
{
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions,
+ SMBUS_NO_STARTSTOP);
}
/* Else transfer direction change, so generate Restart with new transfer direction */
else
@@ -1078,7 +1100,9 @@
SMBUS_ConvertOtherXferOptions(hsmbus);
/* Handle Transfer */
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_GENERATE_START_READ);
+ SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize,
+ hsmbus->XferOptions,
+ SMBUS_GENERATE_START_READ);
}
}
@@ -1222,12 +1246,14 @@
if ((hsmbus->XferSize < hsmbus->XferCount) && (hsmbus->XferSize == MAX_NBYTE_SIZE))
{
SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize,
- SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP);
+ SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE),
+ SMBUS_NO_STARTSTOP);
}
else
{
/* Set NBYTE to transmit */
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions,
+ SMBUS_NO_STARTSTOP);
/* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
/* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
@@ -1313,7 +1339,8 @@
/* This RELOAD bit will be reset for last BYTE to be receive in SMBUS_Slave_ISR */
if (((SMBUS_GET_PEC_MODE(hsmbus) != 0UL) && (hsmbus->XferSize == 2U)) || (hsmbus->XferSize == 1U))
{
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions,
+ SMBUS_NO_STARTSTOP);
}
else
{
@@ -1576,7 +1603,8 @@
uint32_t tmpcr1value = READ_REG(hsmbus->Instance->CR1);
/* SMBUS in mode Transmitter ---------------------------------------------------*/
- if ((SMBUS_CHECK_IT_SOURCE(tmpcr1value, (SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_TXI)) != RESET) &&
+ if ((SMBUS_CHECK_IT_SOURCE(tmpcr1value, (SMBUS_IT_TCI | SMBUS_IT_STOPI |
+ SMBUS_IT_NACKI | SMBUS_IT_TXI)) != RESET) &&
((SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TXIS) != RESET) ||
(SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) ||
(SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) ||
@@ -1600,7 +1628,8 @@
}
/* SMBUS in mode Receiver ----------------------------------------------------*/
- if ((SMBUS_CHECK_IT_SOURCE(tmpcr1value, (SMBUS_IT_TCI | SMBUS_IT_STOPI | SMBUS_IT_NACKI | SMBUS_IT_RXI)) != RESET) &&
+ if ((SMBUS_CHECK_IT_SOURCE(tmpcr1value, (SMBUS_IT_TCI | SMBUS_IT_STOPI |
+ SMBUS_IT_NACKI | SMBUS_IT_RXI)) != RESET) &&
((SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_RXNE) != RESET) ||
(SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TCR) != RESET) ||
(SMBUS_CHECK_FLAG(tmpisrvalue, SMBUS_FLAG_TC) != RESET) ||
@@ -1720,7 +1749,8 @@
* @param AddrMatchCode Address Match Code
* @retval None
*/
-__weak void HAL_SMBUS_AddrCallback(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection, uint16_t AddrMatchCode)
+__weak void HAL_SMBUS_AddrCallback(SMBUS_HandleTypeDef *hsmbus, uint8_t TransferDirection,
+ uint16_t AddrMatchCode)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(hsmbus);
@@ -1879,7 +1909,7 @@
/* Process Unlocked */
__HAL_UNLOCK(hsmbus);
- /* re-enable the selected SMBUS peripheral */
+ /* Re-enable the selected SMBUS peripheral */
__HAL_SMBUS_ENABLE(hsmbus);
/* Call the corresponding callback to inform upper layer of End of Transfer */
@@ -1967,13 +1997,15 @@
if (hsmbus->XferCount > MAX_NBYTE_SIZE)
{
SMBUS_TransferConfig(hsmbus, DevAddress, MAX_NBYTE_SIZE,
- (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)), SMBUS_NO_STARTSTOP);
+ (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)),
+ SMBUS_NO_STARTSTOP);
hsmbus->XferSize = MAX_NBYTE_SIZE;
}
else
{
hsmbus->XferSize = hsmbus->XferCount;
- SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, DevAddress, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions,
+ SMBUS_NO_STARTSTOP);
/* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
/* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
if (SMBUS_GET_PEC_MODE(hsmbus) != 0UL)
@@ -2225,7 +2257,9 @@
else
{
/* Set Reload for next Bytes */
- SMBUS_TransferConfig(hsmbus, 0, 1, SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE), SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, 0, 1,
+ SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE),
+ SMBUS_NO_STARTSTOP);
/* Ack last Byte Read */
hsmbus->Instance->CR2 &= ~I2C_CR2_NACK;
@@ -2237,14 +2271,16 @@
{
if (hsmbus->XferCount > MAX_NBYTE_SIZE)
{
- SMBUS_TransferConfig(hsmbus, 0, MAX_NBYTE_SIZE, (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)),
+ SMBUS_TransferConfig(hsmbus, 0, MAX_NBYTE_SIZE,
+ (SMBUS_RELOAD_MODE | (hsmbus->XferOptions & SMBUS_SENDPEC_MODE)),
SMBUS_NO_STARTSTOP);
hsmbus->XferSize = MAX_NBYTE_SIZE;
}
else
{
hsmbus->XferSize = hsmbus->XferCount;
- SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions, SMBUS_NO_STARTSTOP);
+ SMBUS_TransferConfig(hsmbus, 0, (uint8_t)hsmbus->XferSize, hsmbus->XferOptions,
+ SMBUS_NO_STARTSTOP);
/* If PEC mode is enable, size to transmit should be Size-1 byte, corresponding to PEC byte */
/* PEC byte is automatically sent by HW block, no need to manage it in Transmit process */
if (SMBUS_GET_PEC_MODE(hsmbus) != 0UL)
@@ -2489,7 +2525,8 @@
uint32_t tmperror;
/* SMBUS Bus error interrupt occurred ------------------------------------*/
- if (((itflags & SMBUS_FLAG_BERR) == SMBUS_FLAG_BERR) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
+ if (((itflags & SMBUS_FLAG_BERR) == SMBUS_FLAG_BERR) && \
+ ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
{
hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BERR;
@@ -2498,7 +2535,8 @@
}
/* SMBUS Over-Run/Under-Run interrupt occurred ----------------------------------------*/
- if (((itflags & SMBUS_FLAG_OVR) == SMBUS_FLAG_OVR) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
+ if (((itflags & SMBUS_FLAG_OVR) == SMBUS_FLAG_OVR) && \
+ ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
{
hsmbus->ErrorCode |= HAL_SMBUS_ERROR_OVR;
@@ -2507,7 +2545,8 @@
}
/* SMBUS Arbitration Loss error interrupt occurred ------------------------------------*/
- if (((itflags & SMBUS_FLAG_ARLO) == SMBUS_FLAG_ARLO) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
+ if (((itflags & SMBUS_FLAG_ARLO) == SMBUS_FLAG_ARLO) && \
+ ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
{
hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ARLO;
@@ -2516,7 +2555,8 @@
}
/* SMBUS Timeout error interrupt occurred ---------------------------------------------*/
- if (((itflags & SMBUS_FLAG_TIMEOUT) == SMBUS_FLAG_TIMEOUT) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
+ if (((itflags & SMBUS_FLAG_TIMEOUT) == SMBUS_FLAG_TIMEOUT) && \
+ ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
{
hsmbus->ErrorCode |= HAL_SMBUS_ERROR_BUSTIMEOUT;
@@ -2525,7 +2565,8 @@
}
/* SMBUS Alert error interrupt occurred -----------------------------------------------*/
- if (((itflags & SMBUS_FLAG_ALERT) == SMBUS_FLAG_ALERT) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
+ if (((itflags & SMBUS_FLAG_ALERT) == SMBUS_FLAG_ALERT) && \
+ ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
{
hsmbus->ErrorCode |= HAL_SMBUS_ERROR_ALERT;
@@ -2534,7 +2575,8 @@
}
/* SMBUS Packet Error Check error interrupt occurred ----------------------------------*/
- if (((itflags & SMBUS_FLAG_PECERR) == SMBUS_FLAG_PECERR) && ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
+ if (((itflags & SMBUS_FLAG_PECERR) == SMBUS_FLAG_PECERR) && \
+ ((itsources & SMBUS_IT_ERRI) == SMBUS_IT_ERRI))
{
hsmbus->ErrorCode |= HAL_SMBUS_ERROR_PECERR;
@@ -2582,8 +2624,8 @@
* @param Timeout Timeout duration
* @retval HAL status
*/
-static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag, FlagStatus Status,
- uint32_t Timeout)
+static HAL_StatusTypeDef SMBUS_WaitOnFlagUntilTimeout(SMBUS_HandleTypeDef *hsmbus, uint32_t Flag,
+ FlagStatus Status, uint32_t Timeout)
{
uint32_t tickstart = HAL_GetTick();
@@ -2632,8 +2674,8 @@
* @arg @ref SMBUS_GENERATE_START_WRITE Generate Restart for write request.
* @retval None
*/
-static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size, uint32_t Mode,
- uint32_t Request)
+static void SMBUS_TransferConfig(SMBUS_HandleTypeDef *hsmbus, uint16_t DevAddress, uint8_t Size,
+ uint32_t Mode, uint32_t Request)
{
/* Check the parameters */
assert_param(IS_SMBUS_ALL_INSTANCE(hsmbus->Instance));
@@ -2644,9 +2686,10 @@
MODIFY_REG(hsmbus->Instance->CR2,
((I2C_CR2_SADD | I2C_CR2_NBYTES | I2C_CR2_RELOAD | I2C_CR2_AUTOEND | \
(I2C_CR2_RD_WRN & (uint32_t)(Request >> (31UL - I2C_CR2_RD_WRN_Pos))) | \
- I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_PECBYTE)), \
+ I2C_CR2_START | I2C_CR2_STOP | I2C_CR2_PECBYTE)), \
(uint32_t)(((uint32_t)DevAddress & I2C_CR2_SADD) | \
- (((uint32_t)Size << I2C_CR2_NBYTES_Pos) & I2C_CR2_NBYTES) | (uint32_t)Mode | (uint32_t)Request));
+ (((uint32_t)Size << I2C_CR2_NBYTES_Pos) & I2C_CR2_NBYTES) | \
+ (uint32_t)Mode | (uint32_t)Request));
}
/**
diff --git a/Src/stm32wlxx_hal_smbus_ex.c b/Src/stm32wlxx_hal_smbus_ex.c
new file mode 100644
index 0000000..f249e07
--- /dev/null
+++ b/Src/stm32wlxx_hal_smbus_ex.c
@@ -0,0 +1,146 @@
+/**
+ ******************************************************************************
+ * @file stm32wlxx_hal_smbus_ex.c
+ * @author MCD Application Team
+ * @brief SMBUS Extended HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of SMBUS Extended peripheral:
+ * + Extended features functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### SMBUS peripheral Extended features #####
+ ==============================================================================
+
+ [..] Comparing to other previous devices, the SMBUS interface for STM32WLxx
+ devices contains the following additional features
+
+ (+) Disable or enable Fast Mode Plus
+
+ ##### How to use this driver #####
+ ==============================================================================
+ (#) Configure the enable or disable of fast mode plus driving capability using the functions :
+ (++) HAL_SMBUSEx_EnableFastModePlus()
+ (++) HAL_SMBUSEx_DisableFastModePlus()
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2020 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32wlxx_hal.h"
+
+/** @addtogroup STM32WLxx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup SMBUSEx SMBUSEx
+ * @brief SMBUS Extended HAL module driver
+ * @{
+ */
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup SMBUSEx_Exported_Functions SMBUS Extended Exported Functions
+ * @{
+ */
+
+/** @defgroup SMBUSEx_Exported_Functions_Group1 Extended features functions
+ * @brief Extended features functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Extended features functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to:
+
+ (+) Configure Fast Mode Plus
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Enable the SMBUS fast mode plus driving capability.
+ * @param ConfigFastModePlus Selects the pin.
+ * This parameter can be one of the @ref SMBUSEx_FastModePlus values
+ * @note For I2C1, fast mode plus driving capability can be enabled on all selected
+ * I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently
+ * on each one of the following pins PB6, PB7, PB8 and PB9.
+ * @note For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability
+ * can be enabled only by using I2C_FASTMODEPLUS_I2C1 parameter.
+ * @note For all I2C2 pins fast mode plus driving capability can be enabled
+ * only by using I2C_FASTMODEPLUS_I2C2 parameter.
+ * @note For all I2C3 pins fast mode plus driving capability can be enabled
+ * only by using I2C_FASTMODEPLUS_I2C3 parameter.
+ * @retval None
+ */
+void HAL_SMBUSEx_EnableFastModePlus(uint32_t ConfigFastModePlus)
+{
+ /* Check the parameter */
+ assert_param(IS_SMBUS_FASTMODEPLUS(ConfigFastModePlus));
+
+ /* Enable fast mode plus driving capability for selected pin */
+ SET_BIT(SYSCFG->CFGR1, (uint32_t)ConfigFastModePlus);
+}
+
+/**
+ * @brief Disable the SMBUS fast mode plus driving capability.
+ * @param ConfigFastModePlus Selects the pin.
+ * This parameter can be one of the @ref SMBUSEx_FastModePlus values
+ * @note For I2C1, fast mode plus driving capability can be disabled on all selected
+ * I2C1 pins using I2C_FASTMODEPLUS_I2C1 parameter or independently
+ * on each one of the following pins PB6, PB7, PB8 and PB9.
+ * @note For remaining I2C1 pins (PA14, PA15...) fast mode plus driving capability
+ * can be disabled only by using I2C_FASTMODEPLUS_I2C1 parameter.
+ * @note For all I2C2 pins fast mode plus driving capability can be disabled
+ * only by using I2C_FASTMODEPLUS_I2C2 parameter.
+ * @note For all I2C3 pins fast mode plus driving capability can be disabled
+ * only by using I2C_FASTMODEPLUS_I2C3 parameter.
+ * @retval None
+ */
+void HAL_SMBUSEx_DisableFastModePlus(uint32_t ConfigFastModePlus)
+{
+ /* Check the parameter */
+ assert_param(IS_SMBUS_FASTMODEPLUS(ConfigFastModePlus));
+
+ /* Disable fast mode plus driving capability for selected pin */
+ CLEAR_BIT(SYSCFG->CFGR1, (uint32_t)ConfigFastModePlus);
+}
+
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
diff --git a/Src/stm32wlxx_hal_spi.c b/Src/stm32wlxx_hal_spi.c
index f494700..dd82402 100644
--- a/Src/stm32wlxx_hal_spi.c
+++ b/Src/stm32wlxx_hal_spi.c
@@ -1007,6 +1007,11 @@
*/
HAL_StatusTypeDef HAL_SPI_Receive(SPI_HandleTypeDef *hspi, uint8_t *pData, uint16_t Size, uint32_t Timeout)
{
+#if (USE_SPI_CRC != 0U)
+ __IO uint32_t tmpreg = 0U;
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
+#endif /* USE_SPI_CRC */
uint32_t tickstart;
HAL_StatusTypeDef errorcode = HAL_OK;
@@ -1173,12 +1178,18 @@
if (hspi->Init.DataSize == SPI_DATASIZE_16BIT)
{
/* Read 16bit CRC */
- READ_REG(hspi->Instance->DR);
+ tmpreg = READ_REG(hspi->Instance->DR);
+ /* To avoid GCC warning */
+ UNUSED(tmpreg);
}
else
{
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
/* Read 8bit CRC */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
if ((hspi->Init.DataSize == SPI_DATASIZE_8BIT) && (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT))
{
@@ -1190,7 +1201,9 @@
goto error;
}
/* Read 8bit CRC again in case of 16bit CRC in 8bit Data mode */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
}
}
}
@@ -1241,8 +1254,11 @@
HAL_SPI_StateTypeDef tmp_state;
uint32_t tickstart;
#if (USE_SPI_CRC != 0U)
+ __IO uint32_t tmpreg = 0U;
uint32_t spi_cr1;
uint32_t spi_cr2;
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
#endif /* USE_SPI_CRC */
/* Variable used to alternate Rx and Tx during transfer */
@@ -1476,12 +1492,18 @@
if (hspi->Init.DataSize == SPI_DATASIZE_16BIT)
{
/* Read 16bit CRC */
- READ_REG(hspi->Instance->DR);
+ tmpreg = READ_REG(hspi->Instance->DR);
+ /* To avoid GCC warning */
+ UNUSED(tmpreg);
}
else
{
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
/* Read 8bit CRC */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
if (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT)
{
@@ -1493,7 +1515,9 @@
goto error;
}
/* Read 8bit CRC again in case of 16bit CRC in 8bit Data mode */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
}
}
}
@@ -3048,6 +3072,11 @@
{
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
uint32_t tickstart;
+#if (USE_SPI_CRC != 0U)
+ __IO uint32_t tmpreg = 0U;
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
+#endif /* USE_SPI_CRC */
/* Init tickstart for timeout management*/
tickstart = HAL_GetTick();
@@ -3072,12 +3101,18 @@
if (hspi->Init.DataSize > SPI_DATASIZE_8BIT)
{
/* Read 16bit CRC */
- READ_REG(hspi->Instance->DR);
+ tmpreg = READ_REG(hspi->Instance->DR);
+ /* To avoid GCC warning */
+ UNUSED(tmpreg);
}
else
{
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
/* Read 8bit CRC */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
if (hspi->Init.CRCLength == SPI_CRC_LENGTH_16BIT)
{
@@ -3087,7 +3122,9 @@
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
}
/* Read 8bit CRC again in case of 16bit CRC in 8bit Data mode */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
}
}
}
@@ -3152,6 +3189,11 @@
{
SPI_HandleTypeDef *hspi = (SPI_HandleTypeDef *)(((DMA_HandleTypeDef *)hdma)->Parent); /* Derogation MISRAC2012-Rule-11.5 */
uint32_t tickstart;
+#if (USE_SPI_CRC != 0U)
+ __IO uint32_t tmpreg = 0U;
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
+#endif /* USE_SPI_CRC */
/* Init tickstart for timeout management*/
tickstart = HAL_GetTick();
@@ -3174,8 +3216,12 @@
/* Error on the CRC reception */
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
}
- /* Read CRC to Flush DR and RXNE flag */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
+ /* Read 8bit CRC */
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
}
else
{
@@ -3185,7 +3231,9 @@
SET_BIT(hspi->ErrorCode, HAL_SPI_ERROR_CRC);
}
/* Read CRC to Flush DR and RXNE flag */
- READ_REG(hspi->Instance->DR);
+ tmpreg = READ_REG(hspi->Instance->DR);
+ /* To avoid GCC warning */
+ UNUSED(tmpreg);
}
}
#endif /* USE_SPI_CRC */
@@ -3520,8 +3568,15 @@
*/
static void SPI_2linesRxISR_8BITCRC(struct __SPI_HandleTypeDef *hspi)
{
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
+
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
/* Read 8bit CRC to flush Data Register */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
hspi->CRCSize--;
@@ -3628,8 +3683,12 @@
*/
static void SPI_2linesRxISR_16BITCRC(struct __SPI_HandleTypeDef *hspi)
{
+ __IO uint32_t tmpreg = 0U;
+
/* Read 16bit CRC to flush Data Register */
- READ_REG(hspi->Instance->DR);
+ tmpreg = READ_REG(hspi->Instance->DR);
+ /* To avoid GCC warning */
+ UNUSED(tmpreg);
/* Disable RXNE interrupt */
__HAL_SPI_DISABLE_IT(hspi, SPI_IT_RXNE);
@@ -3684,8 +3743,15 @@
*/
static void SPI_RxISR_8BITCRC(struct __SPI_HandleTypeDef *hspi)
{
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
+
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
/* Read 8bit CRC to flush Data Register */
- READ_REG(*(__IO uint8_t *)&hspi->Instance->DR);
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
hspi->CRCSize--;
@@ -3738,8 +3804,12 @@
*/
static void SPI_RxISR_16BITCRC(struct __SPI_HandleTypeDef *hspi)
{
+ __IO uint32_t tmpreg = 0U;
+
/* Read 16bit CRC to flush Data Register */
- READ_REG(hspi->Instance->DR);
+ tmpreg = READ_REG(hspi->Instance->DR);
+ /* To avoid GCC warning */
+ UNUSED(tmpreg);
/* Disable RXNE and ERR interrupt */
__HAL_SPI_DISABLE_IT(hspi, (SPI_IT_RXNE | SPI_IT_ERR));
@@ -3917,11 +3987,16 @@
__IO uint32_t count;
uint32_t tmp_timeout;
uint32_t tmp_tickstart;
+ __IO uint8_t * ptmpreg8;
+ __IO uint8_t tmpreg8 = 0;
/* Adjust Timeout value in case of end of transfer */
tmp_timeout = Timeout - (HAL_GetTick() - Tickstart);
tmp_tickstart = HAL_GetTick();
+ /* Initialize the 8bit temporary pointer */
+ ptmpreg8 = (__IO uint8_t *)&hspi->Instance->DR;
+
/* Calculate Timeout based on a software loop to avoid blocking issue if Systick is disabled */
count = tmp_timeout * ((SystemCoreClock * 35U) >> 20U);
@@ -3929,8 +4004,10 @@
{
if ((Fifo == SPI_SR_FRLVL) && (State == SPI_FRLVL_EMPTY))
{
- /* Read 8bit CRC to flush Data Register */
- READ_REG(*((__IO uint8_t *)&hspi->Instance->DR));
+ /* Flush Data Register by a blank read */
+ tmpreg8 = *ptmpreg8;
+ /* To avoid GCC warning */
+ UNUSED(tmpreg8);
}
if (Timeout != HAL_MAX_DELAY)
diff --git a/Src/stm32wlxx_hal_subghz.c b/Src/stm32wlxx_hal_subghz.c
index e2fa9a8..bc5a3f7 100644
--- a/Src/stm32wlxx_hal_subghz.c
+++ b/Src/stm32wlxx_hal_subghz.c
@@ -155,6 +155,7 @@
/* SystemCoreClock dividers. Corresponding to time execution of while loop. */
#define SUBGHZ_DEFAULT_LOOP_TIME ((SystemCoreClock*28U)>>19U)
#define SUBGHZ_RFBUSY_LOOP_TIME ((SystemCoreClock*24U)>>20U)
+#define SUBGHZ_NSS_LOOP_TIME ((SystemCoreClock*24U)>>16U)
/**
* @}
*/
@@ -319,6 +320,7 @@
HAL_StatusTypeDef HAL_SUBGHZ_DeInit(SUBGHZ_HandleTypeDef *hsubghz)
{
HAL_StatusTypeDef status;
+ __IO uint32_t count;
/* Check the SUBGHZ handle allocation */
if (hsubghz == NULL)
@@ -363,8 +365,25 @@
LL_PWR_SetRadioBusyTrigger(LL_PWR_RADIO_BUSY_TRIGGER_NONE);
#endif /* CM0PLUS */
- /* Disable the Radio peripheral Reset signal */
- LL_RCC_RF_DisableReset();
+ /* Clear Pending Flag */
+ LL_PWR_ClearFlag_RFBUSY();
+
+ /* Re-asserts the reset signal of the Radio peripheral */
+ LL_RCC_RF_EnableReset();
+
+ /* Verify that Radio in reset status flag is set */
+ count = SUBGHZ_DEFAULT_TIMEOUT * SUBGHZ_DEFAULT_LOOP_TIME;
+
+ do
+ {
+ if (count == 0U)
+ {
+ status = HAL_ERROR;
+ hsubghz->ErrorCode = HAL_SUBGHZ_ERROR_TIMEOUT;
+ break;
+ }
+ count--;
+ } while (LL_RCC_IsRFUnderReset() != 1UL);
hsubghz->ErrorCode = HAL_SUBGHZ_ERROR_NONE;
hsubghz->State = HAL_SUBGHZ_STATE_RESET;
@@ -1677,13 +1696,22 @@
*/
HAL_StatusTypeDef SUBGHZ_CheckDeviceReady(SUBGHZ_HandleTypeDef *hsubghz)
{
+ __IO uint32_t count;
+
/* Wakeup radio in case of sleep mode: Select-Unselect radio */
if (hsubghz->DeepSleep == SUBGHZ_DEEP_SLEEP_ENABLE)
{
+ /* Initialize NSS switch Delay */
+ count = SUBGHZ_NSS_LOOP_TIME;
+
/* NSS = 0; */
LL_PWR_SelectSUBGHZSPI_NSS();
- HAL_Delay(1);
+ /* Wait Radio wakeup */
+ do
+ {
+ count--;
+ } while (count != 0UL);
/* NSS = 1 */
LL_PWR_UnselectSUBGHZSPI_NSS();
diff --git a/Src/stm32wlxx_hal_tim.c b/Src/stm32wlxx_hal_tim.c
index be883ae..a2575c2 100644
--- a/Src/stm32wlxx_hal_tim.c
+++ b/Src/stm32wlxx_hal_tim.c
@@ -103,14 +103,14 @@
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_TIM_RegisterCallback() to register a callback.
- @ref HAL_TIM_RegisterCallback() takes as parameters the HAL peripheral handle,
+ Use Function HAL_TIM_RegisterCallback() to register a callback.
+ HAL_TIM_RegisterCallback() takes as parameters the HAL peripheral handle,
the Callback ID and a pointer to the user callback function.
[..]
- Use function @ref HAL_TIM_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_TIM_UnRegisterCallback() to reset a callback to the default
weak function.
- @ref HAL_TIM_UnRegisterCallback takes as parameters the HAL peripheral handle,
+ HAL_TIM_UnRegisterCallback takes as parameters the HAL peripheral handle,
and the Callback ID.
[..]
@@ -147,7 +147,7 @@
[..]
By default, after the Init and when the state is HAL_TIM_STATE_RESET
all interrupt callbacks are set to the corresponding weak functions:
- examples @ref HAL_TIM_TriggerCallback(), @ref HAL_TIM_ErrorCallback().
+ examples HAL_TIM_TriggerCallback(), HAL_TIM_ErrorCallback().
[..]
Exception done for MspInit and MspDeInit functions that are reset to the legacy weak
@@ -161,7 +161,7 @@
in HAL_TIM_STATE_READY or HAL_TIM_STATE_RESET state,
thus registered(user) MspInit / DeInit callbacks can be used during the Init / DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_TIM_RegisterCallback() before calling DeInit or Init function.
+ using HAL_TIM_RegisterCallback() before calling DeInit or Init function.
[..]
When The compilation define USE_HAL_TIM_REGISTER_CALLBACKS is set to 0 or
@@ -2333,6 +2333,23 @@
return HAL_ERROR;
}
+ /* Enable the Input Capture channel */
+ TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
+
+ /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
+ if (IS_TIM_SLAVE_INSTANCE(htim->Instance))
+ {
+ tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
+ if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+ }
+ else
+ {
+ __HAL_TIM_ENABLE(htim);
+ }
+
switch (Channel)
{
case TIM_CHANNEL_1:
@@ -2419,23 +2436,6 @@
break;
}
- /* Enable the Input Capture channel */
- TIM_CCxChannelCmd(htim->Instance, Channel, TIM_CCx_ENABLE);
-
- /* Enable the Peripheral, except in trigger mode where enable is automatically done with trigger */
- if (IS_TIM_SLAVE_INSTANCE(htim->Instance))
- {
- tmpsmcr = htim->Instance->SMCR & TIM_SMCR_SMS;
- if (!IS_TIM_SLAVEMODE_TRIGGER_ENABLED(tmpsmcr))
- {
- __HAL_TIM_ENABLE(htim);
- }
- }
- else
- {
- __HAL_TIM_ENABLE(htim);
- }
-
/* Return function status */
return HAL_OK;
}
@@ -2690,11 +2690,12 @@
/**
* @brief Starts the TIM One Pulse signal generation.
+ * @note Though OutputChannel parameter is deprecated and ignored by the function
+ * it has been kept to avoid HAL_TIM API compatibility break.
+ * @note The pulse output channel is determined when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @param OutputChannel See note above
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
@@ -2726,7 +2727,7 @@
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
+ whatever the combination, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
No need to enable the counter, it's enabled automatically by hardware
(the counter starts in response to a stimulus and generate a pulse */
@@ -2746,11 +2747,12 @@
/**
* @brief Stops the TIM One Pulse signal generation.
+ * @note Though OutputChannel parameter is deprecated and ignored by the function
+ * it has been kept to avoid HAL_TIM API compatibility break.
+ * @note The pulse output channel is determined when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channels to be disable
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @param OutputChannel See note above
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Stop(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
@@ -2762,7 +2764,7 @@
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
+ whatever the combination, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
@@ -2788,11 +2790,12 @@
/**
* @brief Starts the TIM One Pulse signal generation in interrupt mode.
+ * @note Though OutputChannel parameter is deprecated and ignored by the function
+ * it has been kept to avoid HAL_TIM API compatibility break.
+ * @note The pulse output channel is determined when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @param OutputChannel See note above
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
@@ -2824,7 +2827,7 @@
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
+ whatever the combination, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be enabled together
No need to enable the counter, it's enabled automatically by hardware
(the counter starts in response to a stimulus and generate a pulse */
@@ -2850,11 +2853,12 @@
/**
* @brief Stops the TIM One Pulse signal generation in interrupt mode.
+ * @note Though OutputChannel parameter is deprecated and ignored by the function
+ * it has been kept to avoid HAL_TIM API compatibility break.
+ * @note The pulse output channel is determined when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channels to be enabled
- * This parameter can be one of the following values:
- * @arg TIM_CHANNEL_1: TIM Channel 1 selected
- * @arg TIM_CHANNEL_2: TIM Channel 2 selected
+ * @param OutputChannel See note above
* @retval HAL status
*/
HAL_StatusTypeDef HAL_TIM_OnePulse_Stop_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
@@ -2872,7 +2876,7 @@
(in the OPM Mode the two possible channels that can be used are TIM_CHANNEL_1 and TIM_CHANNEL_2)
if TIM_CHANNEL_1 is used as output, the TIM_CHANNEL_2 will be used as input and
if TIM_CHANNEL_1 is used as input, the TIM_CHANNEL_2 will be used as output
- in all combinations, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
+ whatever the combination, the TIM_CHANNEL_1 and TIM_CHANNEL_2 should be disabled together */
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_1, TIM_CCx_DISABLE);
TIM_CCxChannelCmd(htim->Instance, TIM_CHANNEL_2, TIM_CCx_DISABLE);
diff --git a/Src/stm32wlxx_hal_tim_ex.c b/Src/stm32wlxx_hal_tim_ex.c
index 0e7270c..379e367 100644
--- a/Src/stm32wlxx_hal_tim_ex.c
+++ b/Src/stm32wlxx_hal_tim_ex.c
@@ -1532,8 +1532,10 @@
/**
* @brief Starts the TIM One Pulse signal generation on the complementary
* output.
+ * @note OutputChannel must match the pulse output channel chosen when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channel to be enabled
+ * @param OutputChannel pulse output channel to enable
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
@@ -1542,22 +1544,28 @@
HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
{
uint32_t input_channel = (OutputChannel == TIM_CHANNEL_1) ? TIM_CHANNEL_2 : TIM_CHANNEL_1;
- HAL_TIM_ChannelStateTypeDef input_channel_state = TIM_CHANNEL_STATE_GET(htim, input_channel);
- HAL_TIM_ChannelStateTypeDef output_channel_state = TIM_CHANNEL_N_STATE_GET(htim, OutputChannel);
+ HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1);
+ HAL_TIM_ChannelStateTypeDef channel_2_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_2);
+ HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1);
+ HAL_TIM_ChannelStateTypeDef complementary_channel_2_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_2);
/* Check the parameters */
assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
/* Check the TIM channels state */
- if ((output_channel_state != HAL_TIM_CHANNEL_STATE_READY)
- || (input_channel_state != HAL_TIM_CHANNEL_STATE_READY))
+ if ((channel_1_state != HAL_TIM_CHANNEL_STATE_READY)
+ || (channel_2_state != HAL_TIM_CHANNEL_STATE_READY)
+ || (complementary_channel_1_state != HAL_TIM_CHANNEL_STATE_READY)
+ || (complementary_channel_2_state != HAL_TIM_CHANNEL_STATE_READY))
{
return HAL_ERROR;
}
/* Set the TIM channels state */
- TIM_CHANNEL_N_STATE_SET(htim, OutputChannel, HAL_TIM_CHANNEL_STATE_BUSY);
- TIM_CHANNEL_STATE_SET(htim, input_channel, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY);
/* Enable the complementary One Pulse output channel and the Input Capture channel */
TIM_CCxNChannelCmd(htim->Instance, OutputChannel, TIM_CCxN_ENABLE);
@@ -1573,8 +1581,10 @@
/**
* @brief Stops the TIM One Pulse signal generation on the complementary
* output.
+ * @note OutputChannel must match the pulse output channel chosen when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channel to be disabled
+ * @param OutputChannel pulse output channel to disable
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
@@ -1598,8 +1608,10 @@
__HAL_TIM_DISABLE(htim);
/* Set the TIM channels state */
- TIM_CHANNEL_N_STATE_SET(htim, OutputChannel, HAL_TIM_CHANNEL_STATE_READY);
- TIM_CHANNEL_STATE_SET(htim, input_channel, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY);
/* Return function status */
return HAL_OK;
@@ -1608,8 +1620,10 @@
/**
* @brief Starts the TIM One Pulse signal generation in interrupt mode on the
* complementary channel.
+ * @note OutputChannel must match the pulse output channel chosen when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channel to be enabled
+ * @param OutputChannel pulse output channel to enable
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
@@ -1618,22 +1632,28 @@
HAL_StatusTypeDef HAL_TIMEx_OnePulseN_Start_IT(TIM_HandleTypeDef *htim, uint32_t OutputChannel)
{
uint32_t input_channel = (OutputChannel == TIM_CHANNEL_1) ? TIM_CHANNEL_2 : TIM_CHANNEL_1;
- HAL_TIM_ChannelStateTypeDef input_channel_state = TIM_CHANNEL_STATE_GET(htim, input_channel);
- HAL_TIM_ChannelStateTypeDef output_channel_state = TIM_CHANNEL_N_STATE_GET(htim, OutputChannel);
+ HAL_TIM_ChannelStateTypeDef channel_1_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_1);
+ HAL_TIM_ChannelStateTypeDef channel_2_state = TIM_CHANNEL_STATE_GET(htim, TIM_CHANNEL_2);
+ HAL_TIM_ChannelStateTypeDef complementary_channel_1_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_1);
+ HAL_TIM_ChannelStateTypeDef complementary_channel_2_state = TIM_CHANNEL_N_STATE_GET(htim, TIM_CHANNEL_2);
/* Check the parameters */
assert_param(IS_TIM_CCXN_INSTANCE(htim->Instance, OutputChannel));
/* Check the TIM channels state */
- if ((output_channel_state != HAL_TIM_CHANNEL_STATE_READY)
- || (input_channel_state != HAL_TIM_CHANNEL_STATE_READY))
+ if ((channel_1_state != HAL_TIM_CHANNEL_STATE_READY)
+ || (channel_2_state != HAL_TIM_CHANNEL_STATE_READY)
+ || (complementary_channel_1_state != HAL_TIM_CHANNEL_STATE_READY)
+ || (complementary_channel_2_state != HAL_TIM_CHANNEL_STATE_READY))
{
return HAL_ERROR;
}
/* Set the TIM channels state */
- TIM_CHANNEL_N_STATE_SET(htim, OutputChannel, HAL_TIM_CHANNEL_STATE_BUSY);
- TIM_CHANNEL_STATE_SET(htim, input_channel, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_BUSY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_BUSY);
/* Enable the TIM Capture/Compare 1 interrupt */
__HAL_TIM_ENABLE_IT(htim, TIM_IT_CC1);
@@ -1655,8 +1675,10 @@
/**
* @brief Stops the TIM One Pulse signal generation in interrupt mode on the
* complementary channel.
+ * @note OutputChannel must match the pulse output channel chosen when calling
+ * @ref HAL_TIM_OnePulse_ConfigChannel().
* @param htim TIM One Pulse handle
- * @param OutputChannel TIM Channel to be disabled
+ * @param OutputChannel pulse output channel to disable
* This parameter can be one of the following values:
* @arg TIM_CHANNEL_1: TIM Channel 1 selected
* @arg TIM_CHANNEL_2: TIM Channel 2 selected
@@ -1686,8 +1708,10 @@
__HAL_TIM_DISABLE(htim);
/* Set the TIM channels state */
- TIM_CHANNEL_N_STATE_SET(htim, OutputChannel, HAL_TIM_CHANNEL_STATE_READY);
- TIM_CHANNEL_STATE_SET(htim, input_channel, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_1, HAL_TIM_CHANNEL_STATE_READY);
+ TIM_CHANNEL_N_STATE_SET(htim, TIM_CHANNEL_2, HAL_TIM_CHANNEL_STATE_READY);
/* Return function status */
return HAL_OK;
@@ -2370,15 +2394,17 @@
/* Break input BRK is re-armed automatically by hardware. Poll to check whether fault condition disappeared */
/* Init tickstart for timeout management */
tickstart = HAL_GetTick();
- do
+ while (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BKDSRM) != 0UL)
{
- if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BKDSRM) != TIM_BDTR_BKDSRM)
+ if ((HAL_GetTick() - tickstart) > TIM_BREAKINPUT_REARM_TIMEOUT)
{
- return HAL_OK;
+ /* New check to avoid false timeout detection in case of preemption */
+ if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BKDSRM) != 0UL)
+ {
+ return HAL_TIMEOUT;
+ }
}
- } while ((HAL_GetTick() - tickstart) <= TIM_BREAKINPUT_REARM_TIMEOUT);
-
- return HAL_TIMEOUT;
+ }
}
break;
}
@@ -2391,15 +2417,17 @@
/* Break input BRK2 is re-armed automatically by hardware. Poll to check whether fault condition disappeared */
/* Init tickstart for timeout management */
tickstart = HAL_GetTick();
- do
+ while (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BK2DSRM) != 0UL)
{
- if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BK2DSRM) != TIM_BDTR_BK2DSRM)
+ if ((HAL_GetTick() - tickstart) > TIM_BREAKINPUT_REARM_TIMEOUT)
{
- return HAL_OK;
+ /* New check to avoid false timeout detection in case of preemption */
+ if (READ_BIT(htim->Instance->BDTR, TIM_BDTR_BK2DSRM) != 0UL)
+ {
+ return HAL_TIMEOUT;
+ }
}
- } while ((HAL_GetTick() - tickstart) <= TIM_BREAKINPUT_REARM_TIMEOUT);
-
- return HAL_TIMEOUT;
+ }
}
break;
}
diff --git a/Src/stm32wlxx_hal_uart.c b/Src/stm32wlxx_hal_uart.c
index ccbd0bf..d466234 100644
--- a/Src/stm32wlxx_hal_uart.c
+++ b/Src/stm32wlxx_hal_uart.c
@@ -76,8 +76,8 @@
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_UART_RegisterCallback() to register a user callback.
- Function @ref HAL_UART_RegisterCallback() allows to register following callbacks:
+ Use Function HAL_UART_RegisterCallback() to register a user callback.
+ Function HAL_UART_RegisterCallback() allows to register following callbacks:
(+) TxHalfCpltCallback : Tx Half Complete Callback.
(+) TxCpltCallback : Tx Complete Callback.
(+) RxHalfCpltCallback : Rx Half Complete Callback.
@@ -95,9 +95,9 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_UART_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_UART_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function.
- @ref HAL_UART_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ HAL_UART_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) TxHalfCpltCallback : Tx Half Complete Callback.
@@ -116,16 +116,16 @@
[..]
For specific callback RxEventCallback, use dedicated registration/reset functions:
- respectively @ref HAL_UART_RegisterRxEventCallback() , @ref HAL_UART_UnRegisterRxEventCallback().
+ respectively HAL_UART_RegisterRxEventCallback() , HAL_UART_UnRegisterRxEventCallback().
[..]
- By default, after the @ref HAL_UART_Init() and when the state is HAL_UART_STATE_RESET
+ By default, after the HAL_UART_Init() and when the state is HAL_UART_STATE_RESET
all callbacks are set to the corresponding weak (surcharged) functions:
- examples @ref HAL_UART_TxCpltCallback(), @ref HAL_UART_RxHalfCpltCallback().
+ examples HAL_UART_TxCpltCallback(), HAL_UART_RxHalfCpltCallback().
Exception done for MspInit and MspDeInit functions that are respectively
- reset to the legacy weak (surcharged) functions in the @ref HAL_UART_Init()
- and @ref HAL_UART_DeInit() only when these callbacks are null (not registered beforehand).
- If not, MspInit or MspDeInit are not null, the @ref HAL_UART_Init() and @ref HAL_UART_DeInit()
+ reset to the legacy weak (surcharged) functions in the HAL_UART_Init()
+ and HAL_UART_DeInit() only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the HAL_UART_Init() and HAL_UART_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand).
[..]
@@ -134,8 +134,8 @@
in HAL_UART_STATE_READY or HAL_UART_STATE_RESET state, thus registered (user)
MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_UART_RegisterCallback() before calling @ref HAL_UART_DeInit()
- or @ref HAL_UART_Init() function.
+ using HAL_UART_RegisterCallback() before calling HAL_UART_DeInit()
+ or HAL_UART_Init() function.
[..]
When The compilation define USE_HAL_UART_REGISTER_CALLBACKS is set to 0 or
@@ -1380,7 +1380,7 @@
__HAL_UNLOCK(huart);
/* Enable the TX FIFO threshold interrupt */
- SET_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
}
else
{
@@ -1397,7 +1397,7 @@
__HAL_UNLOCK(huart);
/* Enable the Transmit Data Register Empty interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TXEIE_TXFNFIE);
}
return HAL_OK;
@@ -1452,6 +1452,16 @@
/* Set Reception type to Standard reception */
huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
+ if (!(IS_LPUART_INSTANCE(huart->Instance)))
+ {
+ /* Check that USART RTOEN bit is set */
+ if(READ_BIT(huart->Instance->CR2, USART_CR2_RTOEN) != 0U)
+ {
+ /* Enable the UART Receiver Timeout Interrupt */
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_RTOIE);
+ }
+ }
+
return(UART_Start_Receive_IT(huart, pData, Size));
}
else
@@ -1543,7 +1553,7 @@
/* Enable the DMA transfer for transmit request by setting the DMAT bit
in the UART CR3 register */
- SET_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAT);
return HAL_OK;
}
@@ -1599,6 +1609,16 @@
/* Set Reception type to Standard reception */
huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
+ if (!(IS_LPUART_INSTANCE(huart->Instance)))
+ {
+ /* Check that USART RTOEN bit is set */
+ if(READ_BIT(huart->Instance->CR2, USART_CR2_RTOEN) != 0U)
+ {
+ /* Enable the UART Receiver Timeout Interrupt */
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_RTOIE);
+ }
+ }
+
return(UART_Start_Receive_DMA(huart, pData, Size));
}
else
@@ -1623,17 +1643,17 @@
(gstate == HAL_UART_STATE_BUSY_TX))
{
/* Disable the UART DMA Tx request */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
}
if ((HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) &&
(rxstate == HAL_UART_STATE_BUSY_RX))
{
/* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Disable the UART DMA Rx request */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
}
__HAL_UNLOCK(huart);
@@ -1653,7 +1673,7 @@
if (huart->gState == HAL_UART_STATE_BUSY_TX)
{
/* Enable the UART DMA Tx request */
- SET_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAT);
}
if (huart->RxState == HAL_UART_STATE_BUSY_RX)
{
@@ -1661,11 +1681,11 @@
__HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_OREF);
/* Re-enable PE and ERR (Frame error, noise error, overrun error) interrupts */
- SET_BIT(huart->Instance->CR1, USART_CR1_PEIE);
- SET_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Enable the UART DMA Rx request */
- SET_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAR);
}
__HAL_UNLOCK(huart);
@@ -1694,7 +1714,7 @@
if ((HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT)) &&
(gstate == HAL_UART_STATE_BUSY_TX))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
/* Abort the UART DMA Tx channel */
if (huart->hdmatx != NULL)
@@ -1718,7 +1738,7 @@
if ((HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) &&
(rxstate == HAL_UART_STATE_BUSY_RX))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* Abort the UART DMA Rx channel */
if (huart->hdmarx != NULL)
@@ -1756,20 +1776,20 @@
HAL_StatusTypeDef HAL_UART_Abort(UART_HandleTypeDef *huart)
{
/* Disable TXE, TC, RXNE, PE, RXFT, TXFT and ERR (Frame error, noise error, overrun error) interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE | USART_CR1_TXEIE_TXFNFIE |
- USART_CR1_TCIE));
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE | USART_CR3_RXFTIE | USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE |
+ USART_CR1_TXEIE_TXFNFIE | USART_CR1_TCIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE | USART_CR3_RXFTIE | USART_CR3_TXFTIE);
/* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
}
/* Disable the UART DMA Tx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
/* Abort the UART DMA Tx channel : use blocking DMA Abort API (no callback) */
if (huart->hdmatx != NULL)
@@ -1794,7 +1814,7 @@
/* Disable the UART DMA Rx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* Abort the UART DMA Rx channel : use blocking DMA Abort API (no callback) */
if (huart->hdmarx != NULL)
@@ -1857,13 +1877,13 @@
HAL_StatusTypeDef HAL_UART_AbortTransmit(UART_HandleTypeDef *huart)
{
/* Disable TCIE, TXEIE and TXFTIE interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TCIE | USART_CR1_TXEIE_TXFNFIE));
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TCIE | USART_CR1_TXEIE_TXFNFIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
/* Disable the UART DMA Tx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
/* Abort the UART DMA Tx channel : use blocking DMA Abort API (no callback) */
if (huart->hdmatx != NULL)
@@ -1915,19 +1935,19 @@
HAL_StatusTypeDef HAL_UART_AbortReceive(UART_HandleTypeDef *huart)
{
/* Disable PEIE, EIE, RXNEIE and RXFTIE interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_PEIE | USART_CR1_RXNEIE_RXFNEIE));
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE | USART_CR3_RXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_PEIE | USART_CR1_RXNEIE_RXFNEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE | USART_CR3_RXFTIE);
/* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
}
/* Disable the UART DMA Rx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* Abort the UART DMA Rx channel : use blocking DMA Abort API (no callback) */
if (huart->hdmarx != NULL)
@@ -1984,14 +2004,14 @@
uint32_t abortcplt = 1U;
/* Disable interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_PEIE | USART_CR1_TCIE | USART_CR1_RXNEIE_RXFNEIE |
- USART_CR1_TXEIE_TXFNFIE));
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE | USART_CR3_TXFTIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_PEIE | USART_CR1_TCIE | USART_CR1_RXNEIE_RXFNEIE |
+ USART_CR1_TXEIE_TXFNFIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE | USART_CR3_TXFTIE));
/* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
}
/* If DMA Tx and/or DMA Rx Handles are associated to UART Handle, DMA Abort complete callbacks should be initialised
@@ -2029,7 +2049,7 @@
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT))
{
/* Disable DMA Tx at UART level */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
/* Abort the UART DMA Tx channel : use non blocking DMA Abort API (callback) */
if (huart->hdmatx != NULL)
@@ -2052,7 +2072,7 @@
/* Disable the UART DMA Rx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* Abort the UART DMA Rx channel : use non blocking DMA Abort API (callback) */
if (huart->hdmarx != NULL)
@@ -2134,13 +2154,13 @@
HAL_StatusTypeDef HAL_UART_AbortTransmit_IT(UART_HandleTypeDef *huart)
{
/* Disable interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TCIE | USART_CR1_TXEIE_TXFNFIE));
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TCIE | USART_CR1_TXEIE_TXFNFIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
/* Disable the UART DMA Tx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
/* Abort the UART DMA Tx channel : use non blocking DMA Abort API (callback) */
if (huart->hdmatx != NULL)
@@ -2224,19 +2244,19 @@
HAL_StatusTypeDef HAL_UART_AbortReceive_IT(UART_HandleTypeDef *huart)
{
/* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_PEIE | USART_CR1_RXNEIE_RXFNEIE));
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_PEIE | USART_CR1_RXNEIE_RXFNEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
/* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE));
}
/* Disable the UART DMA Rx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* Abort the UART DMA Rx channel : use non blocking DMA Abort API (callback) */
if (huart->hdmarx != NULL)
@@ -2417,7 +2437,7 @@
/* Disable the UART DMA Rx request if enabled */
if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR))
{
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* Abort the UART DMA Rx channel */
if (huart->hdmarx != NULL)
@@ -2502,18 +2522,18 @@
if (HAL_IS_BIT_CLR(huart->hdmarx->Instance->CCR, DMA_CCR_CIRC))
{
/* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Disable the DMA transfer for the receiver request by resetting the DMAR bit
in the UART CR3 register */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* At end of Rx process, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
/* Last bytes received, so no need as the abort is immediate */
(void)HAL_DMA_Abort(huart->hdmarx);
@@ -2538,10 +2558,10 @@
&&(nb_rx_data > 0U) )
{
/* Disable the UART Parity Error Interrupt and RXNE interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
- /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) and RX FIFO Threshold interrupt */
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
+ /* Disable the UART Error Interrupt:(Frame error, noise error, overrun error) and RX FIFO Threshold interrupt */
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
/* Rx process is completed, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
@@ -2550,7 +2570,7 @@
/* Clear RxISR function pointer */
huart->RxISR = NULL;
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
/*Call registered Rx complete callback*/
huart->RxEventCallback(huart, nb_rx_data);
@@ -2900,7 +2920,7 @@
huart->gState = HAL_UART_STATE_BUSY;
/* Enable USART mute mode by setting the MME bit in the CR1 register */
- SET_BIT(huart->Instance->CR1, USART_CR1_MME);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_MME);
huart->gState = HAL_UART_STATE_READY;
@@ -2920,7 +2940,7 @@
huart->gState = HAL_UART_STATE_BUSY;
/* Disable USART mute mode by clearing the MME bit in the CR1 register */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_MME);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_MME);
huart->gState = HAL_UART_STATE_READY;
@@ -2949,10 +2969,10 @@
huart->gState = HAL_UART_STATE_BUSY;
/* Clear TE and RE bits */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE));
/* Enable the USART's transmit interface by setting the TE bit in the USART CR1 register */
- SET_BIT(huart->Instance->CR1, USART_CR1_TE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TE);
huart->gState = HAL_UART_STATE_READY;
@@ -2972,10 +2992,10 @@
huart->gState = HAL_UART_STATE_BUSY;
/* Clear TE and RE bits */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TE | USART_CR1_RE));
/* Enable the USART's receive interface by setting the RE bit in the USART CR1 register */
- SET_BIT(huart->Instance->CR1, USART_CR1_RE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_RE);
huart->gState = HAL_UART_STATE_READY;
@@ -3452,8 +3472,9 @@
{
/* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error)
interrupts for the interrupt process */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE | USART_CR1_TXEIE_TXFNFIE));
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE |
+ USART_CR1_TXEIE_TXFNFIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
huart->gState = HAL_UART_STATE_READY;
huart->RxState = HAL_UART_STATE_READY;
@@ -3472,8 +3493,9 @@
/* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error)
interrupts for the interrupt process */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE | USART_CR1_TXEIE_TXFNFIE));
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE |
+ USART_CR1_TXEIE_TXFNFIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
huart->gState = HAL_UART_STATE_READY;
huart->RxState = HAL_UART_STATE_READY;
@@ -3515,7 +3537,7 @@
huart->RxState = HAL_UART_STATE_BUSY_RX;
/* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */
- SET_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Configure Rx interrupt processing */
if ((huart->FifoMode == UART_FIFOMODE_ENABLE) && (Size >= huart->NbRxDataToProcess))
@@ -3533,8 +3555,8 @@
__HAL_UNLOCK(huart);
/* Enable the UART Parity Error interrupt and RX FIFO Threshold interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_PEIE);
- SET_BIT(huart->Instance->CR3, USART_CR3_RXFTIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_RXFTIE);
}
else
{
@@ -3551,7 +3573,7 @@
__HAL_UNLOCK(huart);
/* Enable the UART Parity Error interrupt and Data Register Not Empty interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_PEIE | USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_PEIE | USART_CR1_RXNEIE_RXFNEIE);
}
return HAL_OK;
}
@@ -3597,8 +3619,8 @@
__HAL_UNLOCK(huart);
- /* Restore huart->gState to ready */
- huart->gState = HAL_UART_STATE_READY;
+ /* Restore huart->RxState to ready */
+ huart->RxState = HAL_UART_STATE_READY;
return HAL_ERROR;
}
@@ -3606,14 +3628,14 @@
__HAL_UNLOCK(huart);
/* Enable the UART Parity Error Interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_PEIE);
/* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */
- SET_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Enable the DMA transfer for the receiver request by setting the DMAR bit
in the UART CR3 register */
- SET_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAR);
return HAL_OK;
}
@@ -3627,8 +3649,8 @@
static void UART_EndTxTransfer(UART_HandleTypeDef *huart)
{
/* Disable TXEIE, TCIE, TXFT interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TXEIE_TXFNFIE | USART_CR1_TCIE));
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_TXFTIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TXEIE_TXFNFIE | USART_CR1_TCIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_TXFTIE));
/* At end of Tx process, restore huart->gState to Ready */
huart->gState = HAL_UART_STATE_READY;
@@ -3643,13 +3665,13 @@
static void UART_EndRxTransfer(UART_HandleTypeDef *huart)
{
/* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
/* In case of reception waiting for IDLE event, disable also the IDLE IE interrupt source */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
}
/* At end of Rx process, restore huart->RxState to Ready */
@@ -3677,10 +3699,10 @@
/* Disable the DMA transfer for transmit request by resetting the DMAT bit
in the UART CR3 register */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT);
/* Enable the UART Transmit Complete Interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
}
/* DMA Circular mode */
else
@@ -3728,12 +3750,12 @@
huart->RxXferCount = 0U;
/* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Disable the DMA transfer for the receiver request by resetting the DMAR bit
in the UART CR3 register */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR);
/* At end of Rx process, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
@@ -3741,7 +3763,7 @@
/* If Reception till IDLE event has been selected, Disable IDLE Interrupt */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
}
}
@@ -4053,10 +4075,10 @@
if (huart->TxXferCount == 0U)
{
/* Disable the UART Transmit Data Register Empty Interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_TXEIE_TXFNFIE);
/* Enable the UART Transmit Complete Interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
}
else
{
@@ -4084,10 +4106,10 @@
if (huart->TxXferCount == 0U)
{
/* Disable the UART Transmit Data Register Empty Interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_TXEIE_TXFNFIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_TXEIE_TXFNFIE);
/* Enable the UART Transmit Complete Interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
}
else
{
@@ -4118,10 +4140,10 @@
if (huart->TxXferCount == 0U)
{
/* Disable the TX FIFO threshold interrupt */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
/* Enable the UART Transmit Complete Interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
break; /* force exit loop */
}
@@ -4159,10 +4181,10 @@
if (huart->TxXferCount == 0U)
{
/* Disable the TX FIFO threshold interrupt */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_TXFTIE);
/* Enable the UART Transmit Complete Interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TCIE);
break; /* force exit loop */
}
@@ -4190,7 +4212,7 @@
static void UART_EndTransmit_IT(UART_HandleTypeDef *huart)
{
/* Disable the UART Transmit Complete Interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_TCIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_TCIE);
/* Tx process is ended, restore huart->gState to Ready */
huart->gState = HAL_UART_STATE_READY;
@@ -4228,10 +4250,10 @@
if (huart->RxXferCount == 0U)
{
/* Disable the UART Parity Error Interrupt and RXNE interrupts */
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
/* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Rx process is completed, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
@@ -4243,9 +4265,17 @@
If Reception till IDLE event has been selected : */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- /* Disable IDLE interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ /* Set reception type to Standard */
+ huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
+ /* Disable IDLE interrupt */
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+
+ if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE) == SET)
+ {
+ /* Clear IDLE Flag */
+ __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+ }
#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
/*Call registered Rx Event callback*/
huart->RxEventCallback(huart, huart->RxXferSize);
@@ -4265,7 +4295,6 @@
HAL_UART_RxCpltCallback(huart);
#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
}
- huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
}
}
else
@@ -4300,10 +4329,10 @@
if (huart->RxXferCount == 0U)
{
/* Disable the UART Parity Error Interrupt and RXNE interrupt*/
- CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE_RXFNEIE | USART_CR1_PEIE));
/* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE);
/* Rx process is completed, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
@@ -4315,9 +4344,17 @@
If Reception till IDLE event has been selected : */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- /* Disable IDLE interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ /* Set reception type to Standard */
+ huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
+ /* Disable IDLE interrupt */
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+
+ if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE) == SET)
+ {
+ /* Clear IDLE Flag */
+ __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+ }
#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
/*Call registered Rx Event callback*/
huart->RxEventCallback(huart, huart->RxXferSize);
@@ -4337,7 +4374,6 @@
HAL_UART_RxCpltCallback(huart);
#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
}
- huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
}
}
else
@@ -4422,11 +4458,11 @@
if (huart->RxXferCount == 0U)
{
/* Disable the UART Parity Error Interrupt and RXFT interrupt*/
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
/* Disable the UART Error Interrupt: (Frame error, noise error, overrun error)
and RX FIFO Threshold interrupt */
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
/* Rx process is completed, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
@@ -4438,9 +4474,17 @@
If Reception till IDLE event has been selected : */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- /* Disable IDLE interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ /* Set reception type to Standard */
+ huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
+ /* Disable IDLE interrupt */
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+
+ if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE) == SET)
+ {
+ /* Clear IDLE Flag */
+ __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+ }
#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
/*Call registered Rx Event callback*/
huart->RxEventCallback(huart, huart->RxXferSize);
@@ -4460,7 +4504,6 @@
HAL_UART_RxCpltCallback(huart);
#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
}
- huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
}
}
@@ -4472,13 +4515,13 @@
if ((rxdatacount != 0U) && (rxdatacount < huart->NbRxDataToProcess))
{
/* Disable the UART RXFT interrupt*/
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_RXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_RXFTIE);
/* Update the RxISR function pointer */
huart->RxISR = UART_RxISR_8BIT;
/* Enable the UART Data Register Not Empty interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_RXNEIE_RXFNEIE);
}
}
else
@@ -4565,11 +4608,11 @@
if (huart->RxXferCount == 0U)
{
/* Disable the UART Parity Error Interrupt and RXFT interrupt*/
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE);
/* Disable the UART Error Interrupt: (Frame error, noise error, overrun error)
and RX FIFO Threshold interrupt */
- CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, (USART_CR3_EIE | USART_CR3_RXFTIE));
/* Rx process is completed, restore huart->RxState to Ready */
huart->RxState = HAL_UART_STATE_READY;
@@ -4581,9 +4624,17 @@
If Reception till IDLE event has been selected : */
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
- /* Disable IDLE interrupt */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ /* Set reception type to Standard */
+ huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
+ /* Disable IDLE interrupt */
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+
+ if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE) == SET)
+ {
+ /* Clear IDLE Flag */
+ __HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
+ }
#if (USE_HAL_UART_REGISTER_CALLBACKS == 1)
/*Call registered Rx Event callback*/
huart->RxEventCallback(huart, huart->RxXferSize);
@@ -4603,7 +4654,6 @@
HAL_UART_RxCpltCallback(huart);
#endif /* USE_HAL_UART_REGISTER_CALLBACKS */
}
- huart->ReceptionType = HAL_UART_RECEPTION_STANDARD;
}
}
@@ -4615,13 +4665,13 @@
if ((rxdatacount != 0U) && (rxdatacount < huart->NbRxDataToProcess))
{
/* Disable the UART RXFT interrupt*/
- CLEAR_BIT(huart->Instance->CR3, USART_CR3_RXFTIE);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_RXFTIE);
/* Update the RxISR function pointer */
huart->RxISR = UART_RxISR_16BIT;
/* Enable the UART Data Register Not Empty interrupt */
- SET_BIT(huart->Instance->CR1, USART_CR1_RXNEIE_RXFNEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_RXNEIE_RXFNEIE);
}
}
else
diff --git a/Src/stm32wlxx_hal_uart_ex.c b/Src/stm32wlxx_hal_uart_ex.c
index f942f33..ef07235 100644
--- a/Src/stm32wlxx_hal_uart_ex.c
+++ b/Src/stm32wlxx_hal_uart_ex.c
@@ -483,7 +483,7 @@
__HAL_LOCK(huart);
/* Set UESM bit */
- SET_BIT(huart->Instance->CR1, USART_CR1_UESM);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_UESM);
/* Process Unlocked */
__HAL_UNLOCK(huart);
@@ -502,7 +502,7 @@
__HAL_LOCK(huart);
/* Clear UESM bit */
- CLEAR_BIT(huart->Instance->CR1, USART_CR1_UESM);
+ ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_UESM);
/* Process Unlocked */
__HAL_UNLOCK(huart);
@@ -890,7 +890,7 @@
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
__HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
- SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
}
else
{
@@ -969,7 +969,7 @@
if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE)
{
__HAL_UART_CLEAR_FLAG(huart, UART_CLEAR_IDLEF);
- SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
+ ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE);
}
else
{
@@ -1031,8 +1031,8 @@
uint8_t tx_fifo_depth;
uint8_t rx_fifo_threshold;
uint8_t tx_fifo_threshold;
- uint8_t numerator[] = {1U, 1U, 1U, 3U, 7U, 1U, 0U, 0U};
- uint8_t denominator[] = {8U, 4U, 2U, 4U, 8U, 1U, 1U, 1U};
+ static const uint8_t numerator[] = {1U, 1U, 1U, 3U, 7U, 1U, 0U, 0U};
+ static const uint8_t denominator[] = {8U, 4U, 2U, 4U, 8U, 1U, 1U, 1U};
if (huart->FifoMode == UART_FIFOMODE_DISABLE)
{
diff --git a/Src/stm32wlxx_hal_usart.c b/Src/stm32wlxx_hal_usart.c
index f855cb6..aa7d901 100644
--- a/Src/stm32wlxx_hal_usart.c
+++ b/Src/stm32wlxx_hal_usart.c
@@ -62,8 +62,8 @@
allows the user to configure dynamically the driver callbacks.
[..]
- Use Function @ref HAL_USART_RegisterCallback() to register a user callback.
- Function @ref HAL_USART_RegisterCallback() allows to register following callbacks:
+ Use Function HAL_USART_RegisterCallback() to register a user callback.
+ Function HAL_USART_RegisterCallback() allows to register following callbacks:
(+) TxHalfCpltCallback : Tx Half Complete Callback.
(+) TxCpltCallback : Tx Complete Callback.
(+) RxHalfCpltCallback : Rx Half Complete Callback.
@@ -79,9 +79,9 @@
and a pointer to the user callback function.
[..]
- Use function @ref HAL_USART_UnRegisterCallback() to reset a callback to the default
+ Use function HAL_USART_UnRegisterCallback() to reset a callback to the default
weak (surcharged) function.
- @ref HAL_USART_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ HAL_USART_UnRegisterCallback() takes as parameters the HAL peripheral handle,
and the Callback ID.
This function allows to reset following callbacks:
(+) TxHalfCpltCallback : Tx Half Complete Callback.
@@ -97,13 +97,13 @@
(+) MspDeInitCallback : USART MspDeInit.
[..]
- By default, after the @ref HAL_USART_Init() and when the state is HAL_USART_STATE_RESET
+ By default, after the HAL_USART_Init() and when the state is HAL_USART_STATE_RESET
all callbacks are set to the corresponding weak (surcharged) functions:
- examples @ref HAL_USART_TxCpltCallback(), @ref HAL_USART_RxHalfCpltCallback().
+ examples HAL_USART_TxCpltCallback(), HAL_USART_RxHalfCpltCallback().
Exception done for MspInit and MspDeInit functions that are respectively
- reset to the legacy weak (surcharged) functions in the @ref HAL_USART_Init()
- and @ref HAL_USART_DeInit() only when these callbacks are null (not registered beforehand).
- If not, MspInit or MspDeInit are not null, the @ref HAL_USART_Init() and @ref HAL_USART_DeInit()
+ reset to the legacy weak (surcharged) functions in the HAL_USART_Init()
+ and HAL_USART_DeInit() only when these callbacks are null (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, the HAL_USART_Init() and HAL_USART_DeInit()
keep and use the user MspInit/MspDeInit callbacks (registered beforehand).
[..]
@@ -112,8 +112,8 @@
in HAL_USART_STATE_READY or HAL_USART_STATE_RESET state, thus registered (user)
MspInit/DeInit callbacks can be used during the Init/DeInit.
In that case first register the MspInit/MspDeInit user callbacks
- using @ref HAL_USART_RegisterCallback() before calling @ref HAL_USART_DeInit()
- or @ref HAL_USART_Init() function.
+ using HAL_USART_RegisterCallback() before calling HAL_USART_DeInit()
+ or HAL_USART_Init() function.
[..]
When The compilation define USE_HAL_USART_REGISTER_CALLBACKS is set to 0 or
diff --git a/Src/stm32wlxx_hal_usart_ex.c b/Src/stm32wlxx_hal_usart_ex.c
index 59c2184..a10093d 100644
--- a/Src/stm32wlxx_hal_usart_ex.c
+++ b/Src/stm32wlxx_hal_usart_ex.c
@@ -502,8 +502,8 @@
uint8_t rx_fifo_threshold;
uint8_t tx_fifo_threshold;
/* 2 0U/1U added for MISRAC2012-Rule-18.1_b and MISRAC2012-Rule-18.1_d */
- uint8_t numerator[] = {1U, 1U, 1U, 3U, 7U, 1U, 0U, 0U};
- uint8_t denominator[] = {8U, 4U, 2U, 4U, 8U, 1U, 1U, 1U};
+ static const uint8_t numerator[] = {1U, 1U, 1U, 3U, 7U, 1U, 0U, 0U};
+ static const uint8_t denominator[] = {8U, 4U, 2U, 4U, 8U, 1U, 1U, 1U};
if (husart->FifoMode == USART_FIFOMODE_DISABLE)
{
diff --git a/Src/stm32wlxx_ll_adc.c b/Src/stm32wlxx_ll_adc.c
index 05fade2..ba94eb1 100644
--- a/Src/stm32wlxx_ll_adc.c
+++ b/Src/stm32wlxx_ll_adc.c
@@ -232,18 +232,18 @@
* must be disabled.
* @param ADCxy_COMMON ADC common instance
* (can be set directly from CMSIS definition or by using helper macro @ref __LL_ADC_COMMON_INSTANCE() )
- * @param ADC_CommonInitStruct Pointer to a @ref LL_ADC_CommonInitTypeDef structure
+ * @param pADC_CommonInitStruct Pointer to a @ref LL_ADC_CommonInitTypeDef structure
* @retval An ErrorStatus enumeration value:
* - SUCCESS: ADC common registers are initialized
* - ERROR: ADC common registers are not initialized
*/
-ErrorStatus LL_ADC_CommonInit(ADC_Common_TypeDef *ADCxy_COMMON, LL_ADC_CommonInitTypeDef *ADC_CommonInitStruct)
+ErrorStatus LL_ADC_CommonInit(ADC_Common_TypeDef *ADCxy_COMMON, LL_ADC_CommonInitTypeDef *pADC_CommonInitStruct)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_ADC_COMMON_INSTANCE(ADCxy_COMMON));
- assert_param(IS_LL_ADC_COMMON_CLOCK(ADC_CommonInitStruct->CommonClock));
+ assert_param(IS_LL_ADC_COMMON_CLOCK(pADC_CommonInitStruct->CommonClock));
/* Note: Hardware constraint (refer to description of functions */
/* "LL_ADC_SetCommonXXX()": */
@@ -256,7 +256,7 @@
/* - common to several ADC */
/* (all ADC instances belonging to the same ADC common instance) */
/* - Set ADC clock (conversion clock) */
- LL_ADC_SetCommonClock(ADCxy_COMMON, ADC_CommonInitStruct->CommonClock);
+ LL_ADC_SetCommonClock(ADCxy_COMMON, pADC_CommonInitStruct->CommonClock);
}
else
{
@@ -270,16 +270,16 @@
/**
* @brief Set each @ref LL_ADC_CommonInitTypeDef field to default value.
- * @param ADC_CommonInitStruct Pointer to a @ref LL_ADC_CommonInitTypeDef structure
+ * @param pADC_CommonInitStruct Pointer to a @ref LL_ADC_CommonInitTypeDef structure
* whose fields will be set to default values.
* @retval None
*/
-void LL_ADC_CommonStructInit(LL_ADC_CommonInitTypeDef *ADC_CommonInitStruct)
+void LL_ADC_CommonStructInit(LL_ADC_CommonInitTypeDef *pADC_CommonInitStruct)
{
- /* Set ADC_CommonInitStruct fields to default values */
+ /* Set pADC_CommonInitStruct fields to default values */
/* Set fields of ADC common */
/* (all ADC instances belonging to the same ADC common instance) */
- ADC_CommonInitStruct->CommonClock = LL_ADC_CLOCK_ASYNC_DIV2;
+ pADC_CommonInitStruct->CommonClock = LL_ADC_CLOCK_ASYNC_DIV2;
}
@@ -506,22 +506,22 @@
* Refer to function LL_ADC_SetSamplingTimeCommonChannels();
* Refer to function LL_ADC_SetChannelSamplingTime();
* @param ADCx ADC instance
- * @param ADC_InitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
+ * @param pADC_InitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
* @retval An ErrorStatus enumeration value:
* - SUCCESS: ADC registers are initialized
* - ERROR: ADC registers are not initialized
*/
-ErrorStatus LL_ADC_Init(ADC_TypeDef *ADCx, LL_ADC_InitTypeDef *ADC_InitStruct)
+ErrorStatus LL_ADC_Init(ADC_TypeDef *ADCx, LL_ADC_InitTypeDef *pADC_InitStruct)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(ADCx));
- assert_param(IS_LL_ADC_CLOCK(ADC_InitStruct->Clock));
- assert_param(IS_LL_ADC_RESOLUTION(ADC_InitStruct->Resolution));
- assert_param(IS_LL_ADC_DATA_ALIGN(ADC_InitStruct->DataAlignment));
- assert_param(IS_LL_ADC_LOW_POWER(ADC_InitStruct->LowPowerMode));
+ assert_param(IS_LL_ADC_CLOCK(pADC_InitStruct->Clock));
+ assert_param(IS_LL_ADC_RESOLUTION(pADC_InitStruct->Resolution));
+ assert_param(IS_LL_ADC_DATA_ALIGN(pADC_InitStruct->DataAlignment));
+ assert_param(IS_LL_ADC_LOW_POWER(pADC_InitStruct->LowPowerMode));
/* Note: Hardware constraint (refer to description of this function): */
/* ADC instance must be disabled. */
@@ -538,15 +538,15 @@
| ADC_CFGR1_WAIT
| ADC_CFGR1_AUTOFF
,
- ADC_InitStruct->Resolution
- | ADC_InitStruct->DataAlignment
- | ADC_InitStruct->LowPowerMode
+ pADC_InitStruct->Resolution
+ | pADC_InitStruct->DataAlignment
+ | pADC_InitStruct->LowPowerMode
);
MODIFY_REG(ADCx->CFGR2,
ADC_CFGR2_CKMODE
,
- ADC_InitStruct->Clock
+ pADC_InitStruct->Clock
);
}
else
@@ -560,18 +560,18 @@
/**
* @brief Set each @ref LL_ADC_InitTypeDef field to default value.
- * @param ADC_InitStruct Pointer to a @ref LL_ADC_InitTypeDef structure
+ * @param pADC_InitStruct Pointer to a @ref LL_ADC_InitTypeDef structure
* whose fields will be set to default values.
* @retval None
*/
-void LL_ADC_StructInit(LL_ADC_InitTypeDef *ADC_InitStruct)
+void LL_ADC_StructInit(LL_ADC_InitTypeDef *pADC_InitStruct)
{
- /* Set ADC_InitStruct fields to default values */
+ /* Set pADC_InitStruct fields to default values */
/* Set fields of ADC instance */
- ADC_InitStruct->Clock = LL_ADC_CLOCK_SYNC_PCLK_DIV2;
- ADC_InitStruct->Resolution = LL_ADC_RESOLUTION_12B;
- ADC_InitStruct->DataAlignment = LL_ADC_DATA_ALIGN_RIGHT;
- ADC_InitStruct->LowPowerMode = LL_ADC_LP_MODE_NONE;
+ pADC_InitStruct->Clock = LL_ADC_CLOCK_SYNC_PCLK_DIV2;
+ pADC_InitStruct->Resolution = LL_ADC_RESOLUTION_12B;
+ pADC_InitStruct->DataAlignment = LL_ADC_DATA_ALIGN_RIGHT;
+ pADC_InitStruct->LowPowerMode = LL_ADC_LP_MODE_NONE;
}
@@ -610,37 +610,37 @@
* Refer to function LL_ADC_SetSamplingTimeCommonChannels();
* Refer to function LL_ADC_SetChannelSamplingTime();
* @param ADCx ADC instance
- * @param ADC_REG_InitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
+ * @param pADC_RegInitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
* @retval An ErrorStatus enumeration value:
* - SUCCESS: ADC registers are initialized
* - ERROR: ADC registers are not initialized
*/
-ErrorStatus LL_ADC_REG_Init(ADC_TypeDef *ADCx, LL_ADC_REG_InitTypeDef *ADC_REG_InitStruct)
+ErrorStatus LL_ADC_REG_Init(ADC_TypeDef *ADCx, LL_ADC_REG_InitTypeDef *pADC_RegInitStruct)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(ADCx));
- assert_param(IS_LL_ADC_REG_TRIG_SOURCE(ADC_REG_InitStruct->TriggerSource));
- assert_param(IS_LL_ADC_REG_CONTINUOUS_MODE(ADC_REG_InitStruct->ContinuousMode));
- assert_param(IS_LL_ADC_REG_DMA_TRANSFER(ADC_REG_InitStruct->DMATransfer));
- assert_param(IS_LL_ADC_REG_OVR_DATA_BEHAVIOR(ADC_REG_InitStruct->Overrun));
+ assert_param(IS_LL_ADC_REG_TRIG_SOURCE(pADC_RegInitStruct->TriggerSource));
+ assert_param(IS_LL_ADC_REG_CONTINUOUS_MODE(pADC_RegInitStruct->ContinuousMode));
+ assert_param(IS_LL_ADC_REG_DMA_TRANSFER(pADC_RegInitStruct->DMATransfer));
+ assert_param(IS_LL_ADC_REG_OVR_DATA_BEHAVIOR(pADC_RegInitStruct->Overrun));
if (LL_ADC_REG_GetSequencerConfigurable(ADCx) != LL_ADC_REG_SEQ_FIXED)
{
- assert_param(IS_LL_ADC_REG_SEQ_SCAN_LENGTH(ADC_REG_InitStruct->SequencerLength));
+ assert_param(IS_LL_ADC_REG_SEQ_SCAN_LENGTH(pADC_RegInitStruct->SequencerLength));
}
if ((LL_ADC_REG_GetSequencerConfigurable(ADCx) == LL_ADC_REG_SEQ_FIXED)
- || (ADC_REG_InitStruct->SequencerLength != LL_ADC_REG_SEQ_SCAN_DISABLE)
+ || (pADC_RegInitStruct->SequencerLength != LL_ADC_REG_SEQ_SCAN_DISABLE)
)
{
- assert_param(IS_LL_ADC_REG_SEQ_SCAN_DISCONT_MODE(ADC_REG_InitStruct->SequencerDiscont));
+ assert_param(IS_LL_ADC_REG_SEQ_SCAN_DISCONT_MODE(pADC_RegInitStruct->SequencerDiscont));
/* ADC group regular continuous mode and discontinuous mode */
/* can not be enabled simultenaeously */
- assert_param((ADC_REG_InitStruct->ContinuousMode == LL_ADC_REG_CONV_SINGLE)
- || (ADC_REG_InitStruct->SequencerDiscont == LL_ADC_REG_SEQ_DISCONT_DISABLE));
+ assert_param((pADC_RegInitStruct->ContinuousMode == LL_ADC_REG_CONV_SINGLE)
+ || (pADC_RegInitStruct->SequencerDiscont == LL_ADC_REG_SEQ_DISCONT_DISABLE));
}
/* Note: Hardware constraint (refer to description of this function): */
@@ -659,7 +659,7 @@
/* Note: On this STM32 series, ADC trigger edge is set to value 0x0 by */
/* setting of trigger source to SW start. */
if ((LL_ADC_REG_GetSequencerConfigurable(ADCx) == LL_ADC_REG_SEQ_FIXED)
- || (ADC_REG_InitStruct->SequencerLength != LL_ADC_REG_SEQ_SCAN_DISABLE)
+ || (pADC_RegInitStruct->SequencerLength != LL_ADC_REG_SEQ_SCAN_DISABLE)
)
{
/* Case of sequencer mode fixed
@@ -674,11 +674,11 @@
| ADC_CFGR1_DMACFG
| ADC_CFGR1_OVRMOD
,
- ADC_REG_InitStruct->TriggerSource
- | ADC_REG_InitStruct->SequencerDiscont
- | ADC_REG_InitStruct->ContinuousMode
- | ADC_REG_InitStruct->DMATransfer
- | ADC_REG_InitStruct->Overrun
+ pADC_RegInitStruct->TriggerSource
+ | pADC_RegInitStruct->SequencerDiscont
+ | pADC_RegInitStruct->ContinuousMode
+ | pADC_RegInitStruct->DMATransfer
+ | pADC_RegInitStruct->Overrun
);
}
else
@@ -695,18 +695,18 @@
| ADC_CFGR1_DMACFG
| ADC_CFGR1_OVRMOD
,
- ADC_REG_InitStruct->TriggerSource
+ pADC_RegInitStruct->TriggerSource
| LL_ADC_REG_SEQ_DISCONT_DISABLE
- | ADC_REG_InitStruct->ContinuousMode
- | ADC_REG_InitStruct->DMATransfer
- | ADC_REG_InitStruct->Overrun
+ | pADC_RegInitStruct->ContinuousMode
+ | pADC_RegInitStruct->DMATransfer
+ | pADC_RegInitStruct->Overrun
);
}
/* Set ADC group regular sequencer length */
if (LL_ADC_REG_GetSequencerConfigurable(ADCx) != LL_ADC_REG_SEQ_FIXED)
{
- LL_ADC_REG_SetSequencerLength(ADCx, ADC_REG_InitStruct->SequencerLength);
+ LL_ADC_REG_SetSequencerLength(ADCx, pADC_RegInitStruct->SequencerLength);
}
}
else
@@ -719,22 +719,22 @@
/**
* @brief Set each @ref LL_ADC_REG_InitTypeDef field to default value.
- * @param ADC_REG_InitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
+ * @param pADC_RegInitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
* whose fields will be set to default values.
* @retval None
*/
-void LL_ADC_REG_StructInit(LL_ADC_REG_InitTypeDef *ADC_REG_InitStruct)
+void LL_ADC_REG_StructInit(LL_ADC_REG_InitTypeDef *pADC_RegInitStruct)
{
- /* Set ADC_REG_InitStruct fields to default values */
+ /* Set pADC_RegInitStruct fields to default values */
/* Set fields of ADC group regular */
/* Note: On this STM32 series, ADC trigger edge is set to value 0x0 by */
/* setting of trigger source to SW start. */
- ADC_REG_InitStruct->TriggerSource = LL_ADC_REG_TRIG_SOFTWARE;
- ADC_REG_InitStruct->SequencerLength = LL_ADC_REG_SEQ_SCAN_DISABLE;
- ADC_REG_InitStruct->SequencerDiscont = LL_ADC_REG_SEQ_DISCONT_DISABLE;
- ADC_REG_InitStruct->ContinuousMode = LL_ADC_REG_CONV_SINGLE;
- ADC_REG_InitStruct->DMATransfer = LL_ADC_REG_DMA_TRANSFER_NONE;
- ADC_REG_InitStruct->Overrun = LL_ADC_REG_OVR_DATA_OVERWRITTEN;
+ pADC_RegInitStruct->TriggerSource = LL_ADC_REG_TRIG_SOFTWARE;
+ pADC_RegInitStruct->SequencerLength = LL_ADC_REG_SEQ_SCAN_DISABLE;
+ pADC_RegInitStruct->SequencerDiscont = LL_ADC_REG_SEQ_DISCONT_DISABLE;
+ pADC_RegInitStruct->ContinuousMode = LL_ADC_REG_CONV_SINGLE;
+ pADC_RegInitStruct->DMATransfer = LL_ADC_REG_DMA_TRANSFER_NONE;
+ pADC_RegInitStruct->Overrun = LL_ADC_REG_OVR_DATA_OVERWRITTEN;
}
/**
diff --git a/Src/stm32wlxx_ll_i2c.c b/Src/stm32wlxx_ll_i2c.c
index 1e8dd13..43921ec 100644
--- a/Src/stm32wlxx_ll_i2c.c
+++ b/Src/stm32wlxx_ll_i2c.c
@@ -25,7 +25,7 @@
#include "stm32_assert.h"
#else
#define assert_param(expr) ((void)0U)
-#endif
+#endif /* USE_FULL_ASSERT */
/** @addtogroup STM32WLxx_LL_Driver
* @{
diff --git a/Src/stm32wlxx_ll_rcc.c b/Src/stm32wlxx_ll_rcc.c
index 313c1f9..91efbd2 100644
--- a/Src/stm32wlxx_ll_rcc.c
+++ b/Src/stm32wlxx_ll_rcc.c
@@ -69,22 +69,22 @@
/** @defgroup RCC_LL_Private_Functions RCC Private functions
* @{
*/
-uint32_t RCC_PLL_GetFreqDomain_SYS(void);
-uint32_t RCC_PLL_GetFreqDomain_ADC(void);
-uint32_t RCC_PLL_GetFreqDomain_RNG(void);
-uint32_t RCC_PLL_GetFreqDomain_I2S(void);
+static uint32_t RCC_PLL_GetFreqDomain_SYS(void);
+static uint32_t RCC_PLL_GetFreqDomain_ADC(void);
+static uint32_t RCC_PLL_GetFreqDomain_RNG(void);
+static uint32_t RCC_PLL_GetFreqDomain_I2S(void);
-uint32_t RCC_GetSystemClockFreq(void);
+static uint32_t RCC_GetSystemClockFreq(void);
-uint32_t RCC_GetHCLK1ClockFreq(uint32_t SYSCLK_Frequency);
+static uint32_t RCC_GetHCLK1ClockFreq(uint32_t SYSCLK_Frequency);
#if defined(DUAL_CORE)
-uint32_t RCC_GetHCLK2ClockFreq(uint32_t SYSCLK_Frequency);
+static uint32_t RCC_GetHCLK2ClockFreq(uint32_t SYSCLK_Frequency);
#endif /* DUAL_CORE */
-uint32_t RCC_GetHCLK3ClockFreq(uint32_t SYSCLK_Frequency);
+static uint32_t RCC_GetHCLK3ClockFreq(uint32_t SYSCLK_Frequency);
-uint32_t RCC_GetPCLK1ClockFreq(uint32_t HCLK_Frequency);
-uint32_t RCC_GetPCLK2ClockFreq(uint32_t HCLK_Frequency);
+static uint32_t RCC_GetPCLK1ClockFreq(uint32_t HCLK_Frequency);
+static uint32_t RCC_GetPCLK2ClockFreq(uint32_t HCLK_Frequency);
/**
* @}
*/
@@ -778,7 +778,7 @@
* @brief Return SYSTEM clock (SYSCLK) frequency
* @retval SYSTEM clock frequency (in Hz)
*/
-uint32_t RCC_GetSystemClockFreq(void)
+static uint32_t RCC_GetSystemClockFreq(void)
{
uint32_t frequency;
@@ -828,7 +828,7 @@
* @param SYSCLK_Frequency SYSCLK clock frequency
* @retval HCLK1 clock frequency (in Hz)
*/
-uint32_t RCC_GetHCLK1ClockFreq(uint32_t SYSCLK_Frequency)
+static uint32_t RCC_GetHCLK1ClockFreq(uint32_t SYSCLK_Frequency)
{
/* HCLK clock frequency */
return __LL_RCC_CALC_HCLK1_FREQ(SYSCLK_Frequency, LL_RCC_GetAHBPrescaler());
@@ -840,7 +840,7 @@
* @param SYSCLK_Frequency SYSCLK clock frequency
* @retval HCLK2 clock frequency (in Hz)
*/
-uint32_t RCC_GetHCLK2ClockFreq(uint32_t SYSCLK_Frequency)
+static uint32_t RCC_GetHCLK2ClockFreq(uint32_t SYSCLK_Frequency)
{
/* HCLK clock frequency */
return __LL_RCC_CALC_HCLK2_FREQ(SYSCLK_Frequency, LL_C2_RCC_GetAHBPrescaler());
@@ -852,7 +852,7 @@
* @param SYSCLK_Frequency SYSCLK clock frequency
* @retval HCLK3 clock frequency (in Hz)
*/
-uint32_t RCC_GetHCLK3ClockFreq(uint32_t SYSCLK_Frequency)
+static uint32_t RCC_GetHCLK3ClockFreq(uint32_t SYSCLK_Frequency)
{
/* HCLK clock frequency */
return __LL_RCC_CALC_HCLK3_FREQ(SYSCLK_Frequency, LL_RCC_GetAHB3Prescaler());
@@ -863,7 +863,7 @@
* @param HCLK_Frequency HCLK clock frequency
* @retval PCLK1 clock frequency (in Hz)
*/
-uint32_t RCC_GetPCLK1ClockFreq(uint32_t HCLK_Frequency)
+static uint32_t RCC_GetPCLK1ClockFreq(uint32_t HCLK_Frequency)
{
/* PCLK1 clock frequency */
return __LL_RCC_CALC_PCLK1_FREQ(HCLK_Frequency, LL_RCC_GetAPB1Prescaler());
@@ -874,7 +874,7 @@
* @param HCLK_Frequency HCLK clock frequency
* @retval PCLK2 clock frequency (in Hz)
*/
-uint32_t RCC_GetPCLK2ClockFreq(uint32_t HCLK_Frequency)
+static uint32_t RCC_GetPCLK2ClockFreq(uint32_t HCLK_Frequency)
{
/* PCLK2 clock frequency */
return __LL_RCC_CALC_PCLK2_FREQ(HCLK_Frequency, LL_RCC_GetAPB2Prescaler());
@@ -884,7 +884,7 @@
* @brief Return PLL clock (PLLRCLK) frequency used for system domain
* @retval PLLRCLK clock frequency (in Hz)
*/
-uint32_t RCC_PLL_GetFreqDomain_SYS(void)
+static uint32_t RCC_PLL_GetFreqDomain_SYS(void)
{
uint32_t pllinputfreq;
uint32_t pllsource;
@@ -934,7 +934,7 @@
* @brief Return PLL clock (PLLPCLK) frequency used for ADC domain
* @retval PLLPCLK clock frequency (in Hz)
*/
-uint32_t RCC_PLL_GetFreqDomain_ADC(void)
+static uint32_t RCC_PLL_GetFreqDomain_ADC(void)
{
uint32_t pllinputfreq;
uint32_t pllsource;
@@ -982,7 +982,7 @@
* @brief Return PLL clock (PLLQCLK) frequency used for RNG domain
* @retval PLLQCLK clock frequency (in Hz)
*/
-uint32_t RCC_PLL_GetFreqDomain_RNG(void)
+static uint32_t RCC_PLL_GetFreqDomain_RNG(void)
{
uint32_t pllinputfreq;
uint32_t pllsource;
@@ -1030,7 +1030,7 @@
* @brief Return PLL clock (PLLQCLK) frequency used for I2S domain
* @retval PLLQCLK clock frequency (in Hz)
*/
-uint32_t RCC_PLL_GetFreqDomain_I2S(void)
+static uint32_t RCC_PLL_GetFreqDomain_I2S(void)
{
uint32_t pllinputfreq;
uint32_t pllsource;
diff --git a/Src/stm32wlxx_ll_rng.c b/Src/stm32wlxx_ll_rng.c
index 57d10fc..6ef5396 100644
--- a/Src/stm32wlxx_ll_rng.c
+++ b/Src/stm32wlxx_ll_rng.c
@@ -42,7 +42,7 @@
/* Private variables ---------------------------------------------------------*/
/* Private constants ---------------------------------------------------------*/
/* Private macros ------------------------------------------------------------*/
-/** @addtogroup RNG_LL_Private_Macros
+/** @defgroup RNG_LL_Private_Macros RNG Private Macros
* @{
*/
#define IS_LL_RNG_CED(__MODE__) (((__MODE__) == LL_RNG_CED_ENABLE) || \
diff --git a/Src/stm32wlxx_ll_rtc.c b/Src/stm32wlxx_ll_rtc.c
index 1e85f48..b80c475 100644
--- a/Src/stm32wlxx_ll_rtc.c
+++ b/Src/stm32wlxx_ll_rtc.c
@@ -343,7 +343,7 @@
}
/* Exit Initialization mode */
- LL_RTC_DisableInitMode(RTC);
+ LL_RTC_DisableInitMode(RTCx);
/* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
if (LL_RTC_IsShadowRegBypassEnabled(RTCx) == 0U)
@@ -431,7 +431,7 @@
}
/* Exit Initialization mode */
- LL_RTC_DisableInitMode(RTC);
+ LL_RTC_DisableInitMode(RTCx);
/* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
if (LL_RTC_IsShadowRegBypassEnabled(RTCx) == 0U)
diff --git a/Src/stm32wlxx_ll_spi.c b/Src/stm32wlxx_ll_spi.c
index c39fdfc..3478ef6 100644
--- a/Src/stm32wlxx_ll_spi.c
+++ b/Src/stm32wlxx_ll_spi.c
@@ -221,6 +221,12 @@
SPI_CR2_DS | SPI_CR2_SSOE,
SPI_InitStruct->DataWidth | (SPI_InitStruct->NSS >> 16U));
+ /* Set Rx FIFO to Quarter (1 Byte) in case of 8 Bits mode. No DataPacking by default */
+ if (SPI_InitStruct->DataWidth < LL_SPI_DATAWIDTH_9BIT)
+ {
+ LL_SPI_SetRxFIFOThreshold(SPIx, LL_SPI_RX_FIFO_TH_QUARTER);
+ }
+
/*---------------------------- SPIx CRCPR Configuration ----------------------
* Configure SPIx CRCPR with parameters:
* - CRCPoly: CRCPOLY[15:0] bits
diff --git a/Src/stm32wlxx_ll_usart.c b/Src/stm32wlxx_ll_usart.c
index b5f8ce1..4f1a458 100644
--- a/Src/stm32wlxx_ll_usart.c
+++ b/Src/stm32wlxx_ll_usart.c
@@ -66,9 +66,6 @@
/* __VALUE__ In case of oversampling by 16 and 8, BRR content must be greater than or equal to 16d. */
#define IS_LL_USART_BRR_MIN(__VALUE__) ((__VALUE__) >= 16U)
-/* __VALUE__ BRR content must be lower than or equal to 0xFFFF. */
-#define IS_LL_USART_BRR_MAX(__VALUE__) ((__VALUE__) <= 0x0000FFFFU)
-
#define IS_LL_USART_DIRECTION(__VALUE__) (((__VALUE__) == LL_USART_DIRECTION_NONE) \
|| ((__VALUE__) == LL_USART_DIRECTION_RX) \
|| ((__VALUE__) == LL_USART_DIRECTION_TX) \
@@ -252,9 +249,6 @@
/* Check BRR is greater than or equal to 16d */
assert_param(IS_LL_USART_BRR_MIN(USARTx->BRR));
-
- /* Check BRR is lower than or equal to 0xFFFF */
- assert_param(IS_LL_USART_BRR_MAX(USARTx->BRR));
}
/*---------------------------- USART PRESC Configuration -----------------------
@@ -312,37 +306,25 @@
CRx registers */
if (LL_USART_IsEnabled(USARTx) == 0U)
{
- /*---------------------------- USART CR2 Configuration -----------------------*/
- /* If Clock signal has to be output */
- if (USART_ClockInitStruct->ClockOutput == LL_USART_CLOCK_DISABLE)
- {
- /* Deactivate Clock signal delivery :
- * - Disable Clock Output: USART_CR2_CLKEN cleared
- */
- LL_USART_DisableSCLKOutput(USARTx);
- }
- else
- {
- /* Ensure USART instance is USART capable */
- assert_param(IS_USART_INSTANCE(USARTx));
+ /* Ensure USART instance is USART capable */
+ assert_param(IS_USART_INSTANCE(USARTx));
- /* Check clock related parameters */
- assert_param(IS_LL_USART_CLOCKPOLARITY(USART_ClockInitStruct->ClockPolarity));
- assert_param(IS_LL_USART_CLOCKPHASE(USART_ClockInitStruct->ClockPhase));
- assert_param(IS_LL_USART_LASTBITCLKOUTPUT(USART_ClockInitStruct->LastBitClockPulse));
+ /* Check clock related parameters */
+ assert_param(IS_LL_USART_CLOCKPOLARITY(USART_ClockInitStruct->ClockPolarity));
+ assert_param(IS_LL_USART_CLOCKPHASE(USART_ClockInitStruct->ClockPhase));
+ assert_param(IS_LL_USART_LASTBITCLKOUTPUT(USART_ClockInitStruct->LastBitClockPulse));
- /*---------------------------- USART CR2 Configuration -----------------------
- * Configure USARTx CR2 (Clock signal related bits) with parameters:
- * - Enable Clock Output: USART_CR2_CLKEN set
- * - Clock Polarity: USART_CR2_CPOL bit according to USART_ClockInitStruct->ClockPolarity value
- * - Clock Phase: USART_CR2_CPHA bit according to USART_ClockInitStruct->ClockPhase value
- * - Last Bit Clock Pulse Output: USART_CR2_LBCL bit according to USART_ClockInitStruct->LastBitClockPulse value.
- */
- MODIFY_REG(USARTx->CR2,
- USART_CR2_CLKEN | USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL,
- USART_CR2_CLKEN | USART_ClockInitStruct->ClockPolarity |
- USART_ClockInitStruct->ClockPhase | USART_ClockInitStruct->LastBitClockPulse);
- }
+ /*---------------------------- USART CR2 Configuration -----------------------
+ * Configure USARTx CR2 (Clock signal related bits) with parameters:
+ * - Clock Output: USART_CR2_CLKEN bit according to USART_ClockInitStruct->ClockOutput value
+ * - Clock Polarity: USART_CR2_CPOL bit according to USART_ClockInitStruct->ClockPolarity value
+ * - Clock Phase: USART_CR2_CPHA bit according to USART_ClockInitStruct->ClockPhase value
+ * - Last Bit Clock Pulse Output: USART_CR2_LBCL bit according to USART_ClockInitStruct->LastBitClockPulse value.
+ */
+ MODIFY_REG(USARTx->CR2,
+ USART_CR2_CLKEN | USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL,
+ USART_ClockInitStruct->ClockOutput | USART_ClockInitStruct->ClockPolarity |
+ USART_ClockInitStruct->ClockPhase | USART_ClockInitStruct->LastBitClockPulse);
}
/* Else (USART not in Disabled state => return ERROR */
else
