|  | /* | 
|  | * Copyright (c) 2017 Arthur Sfez | 
|  | * | 
|  | * Based on stm32l496g_disco: | 
|  | * | 
|  | * Copyright (c) 2017 Linaro Limited | 
|  | * | 
|  | * SPDX-License-Identifier: Apache-2.0 | 
|  | */ | 
|  |  | 
|  | /dts-v1/; | 
|  | #include <st/l4/stm32l476Xg.dtsi> | 
|  | #include <st/l4/stm32l476v(c-e-g)tx-pinctrl.dtsi> | 
|  |  | 
|  | / { | 
|  | model = "STMicroelectronics STM32L476G-DISCO board"; | 
|  | compatible = "st,stm32l476g-disco"; | 
|  |  | 
|  | chosen { | 
|  | zephyr,console = &usart2; | 
|  | zephyr,shell-uart = &usart2; | 
|  | zephyr,sram = &sram0; | 
|  | zephyr,flash = &flash0; | 
|  | }; | 
|  |  | 
|  | leds { | 
|  | compatible = "gpio-leds"; | 
|  | green_led_4: led_4 { | 
|  | gpios = <&gpiob 2 GPIO_ACTIVE_HIGH>; | 
|  | label = "User LD4"; | 
|  | }; | 
|  | green_led_5: led_5 { | 
|  | gpios = <&gpioe 8 GPIO_ACTIVE_HIGH>; | 
|  | label = "User LD5"; | 
|  | }; | 
|  | }; | 
|  |  | 
|  | gpio_keys { | 
|  | compatible = "gpio-keys"; | 
|  | joy_center: joystick_center { | 
|  | label = "joystick center"; | 
|  | gpios = <&gpioa 0 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; | 
|  | }; | 
|  | joy_down: joystick_down { | 
|  | label = "joystick down"; | 
|  | gpios = <&gpioa 5 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; | 
|  | }; | 
|  | joy_up: joystick_up { | 
|  | label = "joystick up"; | 
|  | gpios = <&gpioa 3 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; | 
|  | }; | 
|  | joy_left: joystick_left { | 
|  | label = "joystick left"; | 
|  | gpios = <&gpioa 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; | 
|  | }; | 
|  | joy_right: joystick_right { | 
|  | label = "joystick right"; | 
|  | gpios = <&gpioa 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; | 
|  | }; | 
|  | }; | 
|  |  | 
|  | aliases { | 
|  | led0 = &green_led_4; | 
|  | sw0 = &joy_center; | 
|  | }; | 
|  | }; | 
|  |  | 
|  | &clk_hsi { | 
|  | status = "okay"; | 
|  | }; | 
|  |  | 
|  | &pll { | 
|  | div-m = <1>; | 
|  | mul-n = <20>; | 
|  | div-p = <7>; | 
|  | div-q = <2>; | 
|  | div-r = <4>; | 
|  | clocks = <&clk_hsi>; | 
|  | status = "okay"; | 
|  | }; | 
|  |  | 
|  | &rcc { | 
|  | clocks = <&pll>; | 
|  | clock-frequency = <DT_FREQ_M(80)>; | 
|  | ahb-prescaler = <1>; | 
|  | apb1-prescaler = <1>; | 
|  | apb2-prescaler = <1>; | 
|  | }; | 
|  |  | 
|  | &usart2 { | 
|  | pinctrl-0 = <&usart2_tx_pd5 &usart2_rx_pd6>; | 
|  | current-speed = <115200>; | 
|  | status = "okay"; | 
|  | }; | 
|  |  | 
|  | &rtc { | 
|  | status = "okay"; | 
|  | }; |