| /* |
| * Copyright (c) 2017 Phytec Messtechnik GmbH |
| * |
| * SPDX-License-Identifier: Apache-2.0 |
| */ |
| |
| #include <init.h> |
| #include <drivers/pinmux.h> |
| #include <fsl_port.h> |
| |
| static int usb_kw24d512_pinmux_init(const struct device *dev) |
| { |
| ARG_UNUSED(dev); |
| |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(porta), okay) |
| __unused const struct device *porta = |
| device_get_binding(DT_LABEL(DT_NODELABEL(porta))); |
| #endif |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(portb), okay) |
| __unused const struct device *portb = |
| device_get_binding(DT_LABEL(DT_NODELABEL(portb))); |
| #endif |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(portc), okay) |
| __unused const struct device *portc = |
| device_get_binding(DT_LABEL(DT_NODELABEL(portc))); |
| #endif |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(portd), okay) |
| __unused const struct device *portd = |
| device_get_binding(DT_LABEL(DT_NODELABEL(portd))); |
| #endif |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(porte), okay) |
| __unused const struct device *porte = |
| device_get_binding(DT_LABEL(DT_NODELABEL(porte))); |
| #endif |
| |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(uart0), okay) && CONFIG_SERIAL |
| /* UART0 RX, TX */ |
| pinmux_pin_set(porta, 1, PORT_PCR_MUX(kPORT_MuxAlt2)); |
| pinmux_pin_set(porta, 2, PORT_PCR_MUX(kPORT_MuxAlt2)); |
| #endif |
| |
| /* SW1 */ |
| pinmux_pin_set(portc, 4, PORT_PCR_MUX(kPORT_MuxAsGpio)); |
| |
| /* blue LEDs D2, D3 */ |
| pinmux_pin_set(portd, 4, PORT_PCR_MUX(kPORT_MuxAsGpio)); |
| pinmux_pin_set(portd, 5, PORT_PCR_MUX(kPORT_MuxAsGpio)); |
| |
| #if DT_NODE_HAS_STATUS(DT_NODELABEL(spi1), okay) && CONFIG_SPI |
| /* SPI1 CS0, SCK, SOUT, SIN */ |
| pinmux_pin_set(portb, 10, PORT_PCR_MUX(kPORT_MuxAlt2)); |
| pinmux_pin_set(portb, 11, PORT_PCR_MUX(kPORT_MuxAlt2)); |
| pinmux_pin_set(portb, 16, PORT_PCR_MUX(kPORT_MuxAlt2)); |
| pinmux_pin_set(portb, 17, PORT_PCR_MUX(kPORT_MuxAlt2)); |
| #endif |
| |
| #ifdef CONFIG_IEEE802154_MCR20A |
| /* Reset, IRQ_B */ |
| pinmux_pin_set(portb, 19, PORT_PCR_MUX(kPORT_MuxAsGpio)); |
| pinmux_pin_set(portb, 3, PORT_PCR_MUX(kPORT_MuxAsGpio)); |
| #endif |
| return 0; |
| } |
| |
| SYS_INIT(usb_kw24d512_pinmux_init, PRE_KERNEL_1, CONFIG_PINMUX_INIT_PRIORITY); |