blob: 9cc78b0f4c823d08c3d0e22fb2bab856cd020afd [file] [log] [blame]
.. _nucleo_g071rb_board:
ST Nucleo G071RB
################
Overview
********
The Nucleo G071RB board features an ARM Cortex-M0+ based STM32G071RB MCU
with a wide range of connectivity support and configurations. Here are
some highlights of the Nucleo G071RB board:
- STM32 microcontroller in QFP64 package
- Two types of extension resources:
- Arduino Uno V3 connectivity
- ST morpho extension pin headers for full access to all STM32 I/Os
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector
- Flexible board power supply:
- USB VBUS or external source(3.3V, 5V, 7 - 12V)
- Power management access point
- Three LEDs: USB communication (LD1), user LED (LD4), power LED (LD3)
- Two push-buttons: USER and RESET
.. image:: img/nucleo_g071rb.jpg
:align: center
:alt: Nucleo G071RB
More information about the board can be found at the `Nucleo G071RB website`_.
Hardware
********
Nucleo G071RB provides the following hardware components:
- STM32 microcontroller in LQFP64 package
- Two types of extension resources:
- Arduino* Uno V3 connectivity
- ST morpho extension pin headers for full access to all STM32 I/Os
- ARM* mbed*
- On-board ST-LINK/V2-1 debugger/programmer with SWD connector:
- Selection-mode switch to use the kit as a standalone ST-LINK/V2-1
- Flexible board power supply:
- USB VBUS or external source (3.3V, 5V, 7 - 12V)
- Power management access point
- Three LEDs:
- USB communication (LD1), user LED (LD4), power LED (LD3)
- Two push-buttons: USER and RESET
- USB re-enumeration capability. Three different interfaces supported on USB:
- Virtual COM port
- Mass storage
- Debug port
- Support of wide choice of Integrated Development Environments (IDEs) including:
- IAR
- ARM Keil
- GCC-based IDEs
More information about STM32G071RB can be found here:
- `G071RB on www.st.com`_
- `STM32G071 reference manual`_
Supported Features
==================
The Zephyr nucleo_g071rb board configuration supports the following hardware features:
+-----------+------------+-------------------------------------+
| Interface | Controller | Driver/Component |
+===========+============+=====================================+
| MPU | on-chip | arm memory protection unit |
+-----------+------------+-------------------------------------+
| NVIC | on-chip | nested vector interrupt controller |
+-----------+------------+-------------------------------------+
| UART | on-chip | serial port-polling; |
| | | serial port-interrupt |
+-----------+------------+-------------------------------------+
| PINMUX | on-chip | pinmux |
+-----------+------------+-------------------------------------+
| GPIO | on-chip | gpio |
+-----------+------------+-------------------------------------+
| I2C | on-chip | i2c |
+-----------+------------+-------------------------------------+
| SPI | on-chip | spi |
+-----------+------------+-------------------------------------+
| CLOCK | on-chip | reset and clock control |
+-----------+------------+-------------------------------------+
| FLASH | on-chip | flash memory |
+-----------+------------+-------------------------------------+
| COUNTER | on-chip | rtc |
+-----------+------------+-------------------------------------+
| WATCHDOG | on-chip | independent watchdog |
+-----------+------------+-------------------------------------+
| PWM | on-chip | pwm |
+-----------+------------+-------------------------------------+
| ADC | on-chip | adc |
+-----------+------------+-------------------------------------+
| DAC | on-chip | dac |
+-----------+------------+-------------------------------------+
| die-temp | on-chip | die temperature sensor |
+-----------+------------+-------------------------------------+
Other hardware features are not yet supported in this Zephyr port.
The default configuration can be found in the defconfig file:
:zephyr_file:`boards/st/nucleo_g071rb/nucleo_g071rb_defconfig`
Connections and IOs
===================
Each of the GPIO pins can be configured by software as output (push-pull or open-drain), as
input (with or without pull-up or pull-down), or as peripheral alternate function. Most of the
GPIO pins are shared with digital or analog alternate functions. All GPIOs are high current
capable except for analog inputs.
Default Zephyr Peripheral Mapping:
----------------------------------
- UART_1 TX/RX : PC4/PC5
- UART_2 TX/RX : PA2/PA3 (ST-Link Virtual Port Com)
- I2C1 SCL/SDA : PB8/PB9 (Arduino I2C)
- I2C2 SCL/SDA : PA11/PA12
- SPI1 NSS/SCK/MISO/MOSI : PB0/PA5/PA6/PA7 (Arduino SPI)
- SPI2 NSS/SCK/MISO/MOSI : PB12/PB13/PB14/PB15
- USER_PB : PC13
- LD4 : PA5
- PWM : PA6
- ADC1 IN0 : PA0
- ADC1 IN1 : PA1
- DAC1_OUT1 : PA4
For more details please refer to `STM32 Nucleo-64 board User Manual`_.
Programming and Debugging
*************************
Applications for the ``nucleo_g071rb`` board configuration can be built and
flashed in the usual way (see :ref:`build_an_application` and
:ref:`application_run` for more details).
Flashing
========
Nucleo G071RB board includes an ST-LINK/V3 embedded debug tool interface.
Flashing an application to Nucleo G071RB
----------------------------------------
Here is an example for the :zephyr:code-sample:`blinky` application.
.. zephyr-app-commands::
:zephyr-app: samples/basic/blinky
:board: nucleo_g071rb
:goals: build flash
You will see the LED blinking every second.
Debugging
=========
You can debug an application in the usual way. Here is an example for the
:ref:`hello_world` application.
.. zephyr-app-commands::
:zephyr-app: samples/hello_world
:board: nucleo_g071rb
:maybe-skip-config:
:goals: debug
References
**********
.. target-notes::
.. _Nucleo G071RB website:
https://www.st.com/en/evaluation-tools/nucleo-g071rb.html
.. _STM32G071 reference manual:
https://www.st.com/resource/en/reference_manual/dm00371828.pdf
.. _STM32 Nucleo-64 board User Manual:
https://www.st.com/resource/en/user_manual/dm00452640.pdf
.. _G071RB on www.st.com:
https://www.st.com/en/microcontrollers/stm32g071rb.html